RACK3000 EMCORE | Alldatasheet
Document overview
- Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
- PDF pages: 2
Technical content
Features
Integrated externally modulated transmitter 0.05 – 18 GHz bandwidth High dynamic range 1 RU rack mount package Front panel RF and optical connections Integrated Microwave Transmitter RACK3000 0.05 – 18 GHz, 1550 nm Externally Modulated Transmitter The Emcore RACK25 01 is an in tegrated, 1 RU high-performance transmitter with guaranteed performance over the 0.05 – 18 GHz frequency b and. It in corporates a high dyn amic range externally modulated transmitter and provides +6 dBm minimum of optical output power. The unit can be use d to constr uct transpa rent optical links for microwave test cell ant enna remoti ng, microwave signal distribution, microwave delay lines, point-to-point data links and other application s where it is necessary to transport RF and microwave signals over long distances without signal degradation. The unit operates at a nominal optical wavelength of 1550 nm. Specifications Electrical RF Connectors SMA (female, 50Ω) Frequency Range 0.05 to 18 GHz TX RF Input Power +25 dBm, max Input IP3 at 18 GHz +28 dBm, typical Input P1dB at 18 GHz +25 dBm, typical Noise Figure 49 dB, typical Optical Wavelength 1550 ± 6 nm Connectors SC/APC TX Optical Output Power +6 to +8 dBm Optical Power Stability <± 0.5 dBm over temperature and time Physical Configuration Self Contained 1 RU Housing, 19” Rack Dimensions 1.75” H x 17” W x 14” D Operating/Storage Temperature 0°C to +50°C Power Requirements 110 VAC @ 50W Interface and Control Front Panel Indicators Power, Link Status LED For more information on this and other products: Contact Sales at Emcore 626-293-3400, or visit www.emcore.com
DATA SHEET – MAY 2008 RACK3000 For more information on this and other products: Contact Sales at Emcore 626-293-3400 or visit www.emcore.com © Copyright 2008, Emcore Corporation EMCORE
2015 West Chestnut Street
Alhambra, California 91803-1542 Tel: 626-293-3400 Fax: 626-293-3428 www.emcore.com Optical Characteristics Parameter Symbol Condition Min Typ Max Unit Wavelength λ - 1530 1550 1565 nm Optical Output Power PL - 6 7 8 dBm Connector Return Loss - - 60 -- -- dB Optical Connector Type FC/APC Note: In order to prevent reflection-induced distortion degradation, the laser should be connected to an optical cable having a return loss of at least 55 dB for discrete reflections and 30 dB for distributed reflections. RF Characteristics Parameter Condition Min Typ Max Unit RF Input Impedance - 50 - Ω RF Return Loss 9.5 15 dB 2nd Harmonic Suppression RF input 0 dBm -60 -45 dBc 1 dB Compression Point +25 dBm RF Connector SMA (Female) Type Link Performance (Measured with 0 dBm TX RF Input and 0 dBm Optical Receiver Input) Parameter Symbol Condition Typ Unit Link Gain G @ 10 GHz -42 dB Gain Variation 50 MHz to 18 GHz 7 dB Input IP3 IIP3 @10 GHz +28 dBm Noise Figure NF @ 10 GHz 49 dB Spurious Free Dynamic Range SFDR @ 10 GHz 98 dB/Hz2/3
Ordering Information
FDA/CDRH Class IIIb laser product. All transmitter versions are Class IIIB laser products per CDRH, 21 CFR 2040 Laser Safety requirements. All versions are Class 3B laser products per IEC*60825-1:1993. Maximum Power = 8 dBm Caution: Use of controls, adjustments and procedures other than those specified herein may result in hazardous laser radiation exposure. *IEC is a registered trademark of the International Electrotechnical Commission.