RAB-32037-000 KNOWLES | Alldatasheet
Document overview
- Manufacturer or author: Provided By alldatasheet.com(free datasheet download site)
- PDF pages: 2
Technical content
| ; | NOTE ; >: POSITIVE GOING VOLTAGE AT TERMINAL 2 | RELATIVE TO TERMINAL I, CAUSES AN INCREASE | IN PRESSURE AT THE SOUND OUTLET | meray Z> DIMENSION TO APPROXIMATE CENTER OF | (2084. 002) TERMINAL PAD LASER MARK | [> Teawiniay ELECTRICALLY CONNECTED TO CASE ON THIS SURFACE | i Sao [E> Locate FROM THE RECEIVER TOP SURFACES TO UUW ADAPTER PLATE EDGE. THE PLATE EDGE CAN‘T = 2 960,05 EXTEND OUT THE RECEIVER OUTLINE SURFACES, PTE 002) BUT ACCEPT BELOW MAX.0. 10mm [.004] +o. 10 0,100,10 —e< 2,17 REF uo 14 REF a—+— 1.46 REF eo] ey 2,01 REF om f (2 Ps.) Mf Ni WETTIG) 2. s8x0.05 ( TI 7 yf 10i. 002) \\ | \\ RO, 4340, 05 eh REF ; | \\ 0,13. REF (01T+.002) ; | y TERMINAL I | LTERMINAL tT] 0,64 3 5840.05 (NEGATIVE) — | (POSITIVE) (025) 60.0 ” | MAXIMUM (1 4lae. 002] (_} > SOLDER BUILDUP SCA | 5 a a : NOMINAL MIE TOMI 5 a a
16 GRAMS DIMENSIONS IN MILLIMETERS CINCHESI Active A
DO NOT SCALE DRAWING cx one ITASCA, ILLINOIS U.S.A. 6 5. ' mw RECEIVER RAB-32037-000 [221-14 OUTLINE DRAWING SHT 1.1 TTT ag
THIS 1S AN UNDAMPED MAGNETIC BALANCED ARMATURE RECEIVER - - INTENDED FOR USE IN HEARING INSTRUMENTS NO DAMPING RAB- 32037 -000 SHEET 2.1 CONSTANT VOLTAGE DRIVE RESPONSE “LE TTT rT SCT TTT LL TTT > wt | | fT Ta F Tit S 110 So gg ftee ee LP S105 ars a en eee ca S= 100 aa . z= yf | dT Tt TN LTT ry ee ~5 90 = es ZS 5 |_| ~ oP TT 2 3 4 5 6789 2 3 4 5 6789 00 1000 10000 FREQUENCY IN HERTZ ACOUSTICAL ELECTRICAL SENSITIVITY DC RESISTANCE 49.0 Q +108 DEVICE WILL PRODUCE THE SPL LISTED BELOW WITH THE TEST : CONDITIONS DESCRIBED IN TABLE 3. NOMINAL SENSITIVITY IMPEDANCE @ 500 Az 76.0 Q 415% AT | kHz IS dB RELATIVE TO 20pPa, ALL OTHER VALUES IN TMPEDANCE @ 1 kA 126.0 © 415% dB RELATIVE TO THE SENSITIVITY AT | kia TNDUCTANCE-@ 300 Ee13T Pa TIP ICAL LIMIT TYPE | FREQUENCY os TABLE 4 ———— a ee ISOLATION: THE CASE WILL BE ELECTRICALLY ISOLATED FROM THE COIL CIRCUIT [REL (S00 OO [REF foo T3800 [3.0 | 2450-3050 MECHANICAL [VALLEY [4000-5400 [i265 [oT PORT LOCATION: 12 PEAK 5200-6200 | 10.0 [to | 4.0 | SOLDER TYPE: ROHS COMPLIANT TABLE | SAC305 TOTAL HARMONIC DISTORTION TEMPERATURE DEVICE WILL NOT EXCEED TOTAL HARMONIC DISTORTION LEVELS OPERATING: SENSITIVITY WILL NOT VARY MORE THAN LISTED BELOW +i/-3 dB FROM 0°C TO 63°C FREQUENCY (Hz) DRIVE (V rms)} LIMIT (4) STORAGE: -40"C TO 65°C /3 PEAKI (TYP. 917) /2 PEAK (TYP. 1375) TABLE 2 TEST CONDITIONS SOURCE _INPEDANCE TUBING 10 mm (,394) LONG, | mm (.039) 1D COUPLER CAVITY 2 CC SIMULATED ANSI 93.7 TYPE HA-3, (IEC 60318-5) TABLE 3 [ Revision | C.0. # J Implementation Date T RELEASE LEVEL REVISION | re ee ee . po Active A WHEN TEST LIMITS ARE USED TO ESTABLISH INCOMING INSPECTION ACCEPTANCE/ REJECTION CRITERIA, CORRELATION OF TEST EQUIPMENT WITH KNOWLES IS ALSO REQUIRED FOR ELIMINATION OF EQUIPMENT AND TEST METHOD VARIATION LW 4-14-14 KNOWLES ELECTRONICS ITASCA, ILLINOIS U.S.A. me RECEIVER RAB-32037-000 = oe __+ 18-14 PERFORMANCE SPECIFICATION SHT 2.1