R6P-SM MSYSTEM | Alldatasheet

Document overview

  • Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
  • PDF pages: 3

Technical content

MODEL: R6-PSM R6-PSM SPECIFICATIONS ES-7781-BZ Rev.1 Page 1/3 https://www.m-system.co.jp/ Remote I/O R6 Series POWER SUPPLY MODULE Functions & Features

  • Provides internal power needed for I/O and network modules from power input
  • Universal AC power input 96.5 (3.80) 18 (.71) (3.54) mm (inch) MODEL: R6-PSM

ORDERING INFORMATION

  • Code number: R6-PSM[1] Specify a code from below for [1]. (e.g. R6-PSM/Q)
  • Specify the specification for option code /Q (e.g. /C01) POWER INPUT AC Power 100 – 240 V AC (Operational voltage range 90 – 264 V, 47 – 66 Hz) [1] OPTIONS blank: none /Q: With options (specify the specification) SPECIFICATIONS OF OPTION: Q COATING (For the detail, refer to M-System's web site.) /C01: Silicone coating /C02: Polyurethane coating

RELATED PRODUCTS

  • Euro terminal remote I/O R6D series
  • Screw terminal remote I/O R6N series
  • Tension-clamp remote I/O R6S series GENERAL SPECIFICATIONS Connection Internal bus: Via the Installation Base (model: R6x-BS8B) RUN contact output, power supply: Euro type connector terminal (Applicable wire size: 0.2 to 2.5 mm2, stripped length 7 mm) Internal power supply: Via the Installation Base (model: R6x -BS8B) Housing material: Flame-resistant resin (black) Isolation: RUN contact output to internal bus or internal power to power supply to FG Power indicator: Bi-color (green/amber) LED; Green turns ON when the power is supplied. Amber turns ON in normal communication. ■ RUN CONTACT OUTPUT RUN contact: ON in normal communication with the host PLC; OFF in communication error. Rated load: 250 V AC @ 0.5 A (cos ø = 1) 30 V DC @ 0.5 A (resistive load) Maximum switching voltage: 250 V AC or 30 V DC Maximum switching power: 250 VA or 150 W Minimum load: 5 V DC @ 10 mA Mechanical life: 2 × 107 cycles (rate 300 cycles/min.) When driving an inductive load, external contact protection and noise quenching recommended. INSTALLATION Power input
  • AC: Approx. 25 VA at 100 V Approx. 30 VA at 200 V Approx. 35 VA at 264 V Operating temperature: -10 to +55°C (14 to 131°F) Operating humidity: 30 to 90 %RH (non-condensing) Mounting: Installation Base (model: R6x-BS8B) Weight: 120 g (0.26 lb) PERFORMANCE Output (internal power):

24 V ±1 V DC, 400 mA (continuance)

Arrange in order that the total current consumed by the I/O modules or Network modules is within this capacity. Insulation resistance: ≥ 100 MΩ with 500 V DC Dielectric strength: 2000 V AC @ 1 minute (RUN contact output to internal bus or internal power to power input to FG)

MODEL: R6-PSM R6-PSM SPECIFICATIONS ES-7781-BZ Rev.1 Page 2/3 https://www.m-system.co.jp/ STANDARDS & APPROVALS EU conformity: EMC Directive EMI EN 61000-6-4 EMS EN 61000-6-2 Low Voltage Directive EN 61010-1,EN 61010-2-201 Measurement Category II (RUN contact output) Installation Category II (power input) Pollution Degree 2 Internal power or RUN contact output to power input to FG: Reinforced insulation (300 V) Internal power to RUN contact output: Basic insulation (300 V) RoHS Directive CURRENT CONSUMPTION The network module and I/O modules operate with 24V DC power supply via the power supply module. The total current consumption of the network module and I/O modules is required to be not more than the continuance output current (400mA) of the power supply module. If the total current consumption exceeds the capacity of the power supply module, change the combination of I/O modules or reduce the number of I/O modules. R6xSV2 20mA R6xSS2 20mA R6xTS2 20mA R6xTS2A 20mA R6xRS2 20mA R6xDS1 55mA R6xYV2 25mA R6xYS2 45mA R6xDA4 10mA R6xDC4A 20mA R6xDC4B 20mA R6NC1 110mA R6NC3 110mA R6ND1 40mA R6NE1 75mA R6NE2 75mA R6NM1 50mA R6NM2 50mA R6NF1 100mA R6NP1 100mA

MODEL: R6-PSM R6-PSM SPECIFICATIONS ES-7781-BZ Rev.1 Page 3/3 https://www.m-system.co.jp/ EXTERNAL VIEW 4 5 6 1 2 3 POWER Power LED Connector Euro type terminal block EXTERNAL DIMENSIONS & TERMINAL ASSIGNMENTS unit: mm [inch] 4 5 6 1 2 3 18 (0.71) 90 (3.54) 5.6 (.22) LOCKING CLAMP POSITIONING GUIDE SCHEMATIC CIRCUITRY & CONNECTION DIAGRAM Note: In order to improve EMC performance, bond the FG terminal to ground. Caution: FG terminal is NOT a protective conductor terminal. INTERNAL POWER Control Circuit Output Driver POWER LED V U FG POWER INPUT RUN+ RUN– RUN CONTACT OUTPUT BUS CONNECTOR Ry INTERNAL BUS Specifications are subject to change without notice.