R474W14700002K

DATASHEET SEARCH SITE | WWW.ALLDATASHEET.COM

Document overview

• Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
• PDF pages: 17

Technical content

© KEMET Electronics Corporation • P.O. Box 5928 • Greenville, SC 29606 (864) 963-6300 • www.kemet.com F3 096_R47_X2_440 • 6/9/2016 One world. One KEMET Benefits

• A pprovals: ENEC, UL, cUL C lass X2 (IEC 60384-14) R ated voltage: 440 VAC 50/60 Hz Ca pacitance range: 0.0047 – 2.2 µF L ead spacing: 10.0 – 37.5 mm Ca pacitance tolerance: ±20%, ±10% C limatic category: 40/110/56, IEC 60068–1 T ape and reel in accordance with IEC 60286–2 R oHS Compliant and lead-free terminations
• Operating temperature range of −40˚C to +110˚C 00% screening factory test at 2,200 VDC/1,500 VAC S elf-healing properties A utomotive (AEC–Q200) grades available up to 22.5 mm Lead Spacing Overview The R47 Series is constructed of metallized polypropylene film encapsulated with self-extinguishing resin in a box of material meeting the requirements of UL 94 V–0. Automotive Grade devices are available (up to 22.5 mm Lead Spacing) and meet the demanding Automotive Electronics Council's AEC–Q200 qualification requirements.

Applications

For worldwide use in electromagnetic interference (EMI) suppression in across-the-line applications requiring X2 safety classification. Intended for use in situations where capacitor failure would not result in exposure to electric shock. Metallized Polypropylene Film EMI Suppression Capacitors R47 Series, Class X2, 440 VAC, 110ºC (Automotive Grade) Part Number System R47 4 F 1470 00 01 M Series Rated Voltage (VAC) Lead Spacing (mm) Capacitance Code (pF) Packaging Internal Use Capacitance Tolerance X2, Metallized Polypropylene 4 = 440 F = 10.0 I = 15.0 N = 22.5 R = 27.5 W = 37.5 The last three digits represent si gnificant fi gures. The first d igit specifies n umber of zeros to be added. See Ordering Options Table K = ±10% M = ±20%

© KEMET Electronics Corporation • P.O. Box 5928 • Greenville, SC 29606 (864) 963-6300 • www.kemet.com F3 096_R47_X2_440 • 6/9/2016 Metallized Polypropylene Film EMI Suppression Capacitors R47 Series, Class X2, 440 VAC, 110ºC (Automotive Grade) Ordering Options Table Lead Spacing Nominal (mm) Type of Leads and Packaging Lead Length (mm) Lead and Packaging Code 10, 15, 22.5 Standard Lead and Packaging Options Bulk (Bag) – Short Leads 4 +2/-0 00 Ammo Pack H0= 18.5 +/-0.5 DQ Other Lead and Packaging Options Tape & Reel (Large Reel) H0= 18.5 +/-0.5 CK B ulk (Bag) – Short Leads 3.5 +0.5/-0 JB Bulk (Bag) – Short Leads 4.0 +0.5/-0 JE Bulk (Bag) – Long Leads 30 +5/-0 40 Bulk (Bag) – Long Leads 25 +2/-1 50 27.5, 37.5 Standard Lead and Packaging Options Bulk (Bag) – Short Leads 4 +2/-0 00 Tape & Reel (Large Reel) H0= 18.5 +/-0.5 CK Other Lead and Packaging Options Bulk (Bag) – Short Leads 3.5 +0.5/-0 JB Bulk (Bag) – Long Leads 30 +5/-0 40 Bulk (Bag) – Long Leads 25 +2/-1 50

© KEMET Electronics Corporation • P.O. Box 5928 • Greenville, SC 29606 (864) 963-6300 • www.kemet.com F3 096_R47_X2_440 • 6/9/2016 Metallized Polypropylene Film EMI Suppression Capacitors R47 Series, Class X2, 440 VAC, 110ºC (Automotive Grade) Dimensions – Millimeters H p LL d L B FRONT VIEW SIDE VIEW p B H L d Nominal Tolerance Nominal Tolerance Nominal Tolerance Nominal Tolerance Nominal Tolerance Note: See Ordering Options Table for lead length (LL/H 0) options.

© KEMET Electronics Corporation • P.O. Box 5928 • Greenville, SC 29606 (864) 963-6300 • www.kemet.com F3 096_R47_X2_440 • 6/9/2016 Metallized Polypropylene Film EMI Suppression Capacitors R47 Series, Class X2, 440 VAC, 110ºC (Automotive Grade) Performance Characteristics Dielectric Polypropylene film Plates Metal layer deposited by evaporation under vacuum Winding Non-inductive type Leads Tinned wire Protection Plastic case, thermosetting resin filled. Box material is solvent resistant and flame retardant according to UL94. Related documents IEC 60384-14, EN 60384-14 Rated Voltage (VR) 440 VAC (50/60 Hz), 1,000 VDC Capacitance Range 4700 pF to 1 µF Capacitance Values E6 series (IEC 60063) measured kHz and +20 ±1°C Capacitance Tolerance ±10%, ±20% Temperature Range −40ºC to +110°C Climatic Category 40/110/56 IEC 60068-1 Storage Conditions Storage time: months from the date marked on the label package Average relative humidity per year 70% R H 85% for days randomly distributed throughout the year Dew is absent Temperature: −40 to 80°C (see "Maximum Humidity in Storage Conditions" graph below) Approvals ENEC, UL, cUL

© KEMET Electronics Corporation • P.O. Box 5928 • Greenville, SC 29606 (864) 963-6300 • www.kemet.com F3 096_R47_X2_440 • 6/9/2016 Metallized Polypropylene Film EMI Suppression Capacitors R47 Series, Class X2, 440 VAC, 110ºC (Automotive Grade) Performance Characteristics cont'd Impedance Graph Environmental Test Data Test IEC Publication Procedure Endurance EN/IEC 60384–14 1.25 x VR VAC 50 Hz, once every hour increase to 1,000 VAC for 0.1 second, 1,000 hours at upper rated temperature Vibration IEC 60068–2–6 Test Fc 3 directions at 2 hours each 10 – 55 Hz at 0.75 mm or 98 m/s 2 Bump IEC 60068–2–29 Test Eb 1,000 bumps at 390 m/s 2 Change of Temperature IEC 60068–2–14 Test Na Upper and lower rated temperature 5 cycles Active Flammability IEC 60384–14 VR + 20 surge pulses at 2.5 kV (pulse every 5 seconds) P assive Flammability IEC 60384–14 IEC 60384–1, IEC 60695–11–5 Needle flame test Damp Heat Steady State IEC 60068–2–78 Test Cab +40°C and 93% RH, days Dissipation Factor (tanδ) ≤ 0.1% (0.06%*) @ 1 kHz , +25°C ±5°C (* typical value) Test Voltage Between Terminals The 100% screening factory test is carried out at 2,700 VDC/1,700 VAC. The voltage level is selected to meet the requirements in applicable equipment standards. All electrical characteristics are checked after the test. It is not permitted to repeat this test as there is a risk to damage the capacitor. KEMET is not liable in such case for any failures. Insulation Resistance Measured at +25°C ±5°C, according to IEC 60384–2 Minimum Values Between Terminals Voltage Charge Voltage Charge Time C 0.33 μF C 0.33 μF

100 VDC 1 minute ≥

105 MΩ ≥ 30,000 MΩ • µF

In DC Applications Recommended voltage 1,000 VDC

© KEMET Electronics Corporation • P.O. Box 5928 • Greenville, SC 29606 (864) 963-6300 • www.kemet.com F3 096_R47_X2_440 • 6/9/2016 Metallized Polypropylene Film EMI Suppression Capacitors R47 Series, Class X2, 440 VAC, 110ºC (Automotive Grade) Approvals Mark Specification File Number EN/IEC 60384-14 CA08.00101 UL 60384-14 and CAN/CSA E60384-14 (440VAC) E97797 Environmental Compliance All KEMET EMI capacitors are RoHS Compliant.

© KEMET Electronics Corporation • P.O. Box 5928 • Greenville, SC 29606 (864) 963-6300 • www.kemet.com F3 096_R47_X2_440 • 6/9/2016 Metallized Polypropylene Film EMI Suppression Capacitors R47 Series, Class X2, 440 VAC, 110ºC (Automotive Grade) Table 1 – Ratings & Part Number Reference Capacitance Value (µF) Dimensions in mm Lead Spacing (p) dV/dt (V/µs) New KEMET Part Number Legacy Part Number B H L Capacitance Value (µF) B (mm) H (mm) L (mm) Lead Spacing (p) dV/dt (V/µs) New KEMET Part Number Legacy Part Number (1) Insert ordering code for lead type and packaging. See Ordering Options Table for available options.

© KEMET Electronics Corporation • P.O. Box 5928 • Greenville, SC 29606 (864) 963-6300 • www.kemet.com F3 096_R47_X2_440 • 6/9/2016 Metallized Polypropylene Film EMI Suppression Capacitors R47 Series, Class X2, 440 VAC, 110ºC (Automotive Grade) Manual Soldering Recommendations Following is the recommendation for manual soldering with a soldering iron. The soldering iron tip temperature should be set at 350°C (+10°C maximum) with the soldering duration not to exceed more than 3 seconds. Recommended Soldering Temperature 100 150 200 250 300 350 400 0 1 2 3 4 5 6 7 8 Soldering time (sec) Soldering iron bit temperature (deg C) Soldering Process The implementation of the RoHS directive has resulted in the selection of SnAgCu (SAC) alloys or SnCu alloys as primary solder. This has increased the liquidus temperature from that of 183ºC for SnPb eutectic alloy to 217 221ºC for the new alloys. As a result, the heat stress to the components, even in wave soldering, has increased considerably due to higher pre-heat and wave temperatures. Polypropyle ne capacitors are especially sensitive to heat (the melting point of polypropylene is 160 170ºC). Wave soldering can be destructive, especially for mechanically small polypropylene capacitors (with lead spacing of 5 mm to 15 mm), and great care has to be taken during sol dering. The recommended solder profiles from KEMET should be used. Please consult KEMET with any questions. In general, the wave soldering curve from IEC Publication 61760-1 Edition 2 serves as a solid guideline for successful soldering. Please see Figure 1. Reflow soldering is not recommended for through-hole film capacitors. Exposing capacitors to a soldering profile in excess of the above the recommended limits may result to degradation or permanent damage to the capacitors. Do not place the polypropylene capacitor through an adhesive curing oven to cure resin for surface mount components. Insert through- hole parts after the curing of surface mount parts. Consult KEMET to discuss the actual temperature profile in the oven, if through-hole components must pass through the adhesive curing process. A maximum two soldering cycles is recommended. Please allow time for the capacitor surface temperature to return to a normal temperature before the second soldering cycle. Wave Soldering Recommendations 100 150 200 250 300 0 40 80 120 160 200 240 Temperature (°C) Time (s) ca 2°C/s ca 3.5°C/s typical ca 5°C/s Cooling 2+3s max 115°C max Tpreheat ΔT <150°C 100°C Preheating Typical First wave Second wave 260°C

© KEMET Electronics Corporation • P.O. Box 5928 • Greenville, SC 29606 (864) 963-6300 • www.kemet.com F3 096_R47_X2_440 • 6/9/2016 Metallized Polypropylene Film EMI Suppression Capacitors R47 Series, Class X2, 440 VAC, 110ºC (Automotive Grade) Soldering Process cont'd Wave Soldering Recommendations cont'd 1. The table indicates the maximum set-up temperature of the soldering process Figure 1 Dielectric Film Material Maximum Preheat Temperature Maximum Peak Soldering Temperature Capacitor Pitch mm Capacitor Pitch = 15 mm Capacitor Pitch > 15 mm Capacitor Pitch mm Capacitor Pitch > 15 mm Polyester 130°C 130°C 130°C 270°C 270°C Polypropylene 100°C 110°C 130°C 260°C 270°C Paper 130°C 130°C 140°C 270°C 270°C Polyphenylene Sulphide 150°C 150°C 160°C 270°C 270°C 2. The maximum temperature measured inside the capacitor: S et the temperature so that inside the element the maximum temperature is below the limit: Dielectric Film Material Maximum temperature measured inside the element Polyester 160°C Polypropylene 110°C Paper 160°C Polyphenylene sulphide 160°C Temperature monitored inside the capacitor. Selective Soldering Recommendations Selective dip soldering is a variation of reflow soldering. In this method, the printed circuit board with through-hole components to be soldered is preheated and transported over the solder bath as in normal flow soldering without touching the solder. When the board is over the bath, it is stopped and pre-designed solder pots are lifted from the bath with molten solder only at the places of the selected components, and pressed against the lower surface of the board to solder the components. The temperature profile for selective soldering is similar to the double wave flow soldering outlined in this document, however , instead of two baths, there is only one bath with a time from 3 to 10 seconds. In selective soldering, the risk of overheating is greater than in double wave flow soldering, and great care must be taken so that the parts are not overheated.

© KEMET Electronics Corporation • P.O. Box 5928 • Greenville, SC 29606 (864) 963-6300 • www.kemet.com F3 096_R47_X2_440 • 6/9/2016 Metallized Polypropylene Film EMI Suppression Capacitors R47 Series, Class X2, 440 VAC, 110ºC (Automotive Grade) Construction Detailed Cross Section Self-Extinguishing Resin Molded Plastic Case Molded Plastic Case Leads Metal Contact Layer Metal Contact Layer Margin Single-sided Metallized Polypropylene Film (Second Layer) Single-sided Metallized Polypropylene Film (First Layer) Margin Margin

2 Sections

FILM WINDING SCHEME OPTIONS

1 Section

Single-sided Metallized Polypropylene Film

3 Sections 4 Sections

Double-sided Metallized Polyester Film

3 Sections

Film DielectricDouble-sided Metallized Polyester Carrier Film Single-sided Metallized Polypropylene Film

4 Sections

Film DielectricDouble-sided Metallized Polyester Carrier Film Polypropylene Film Dielectric Sulfide Film (SMR) Metallized Impregnated Paper Metallized Impregnated Paper Single-sided Metallized Polyester Film Single-sided Metallized Polyester Film Polypropylene Film Dielectric AXIAL - Polypropylene Film/Foil AXIAL - Single-sided Metallized Polypropylene Film Single-sided Metallized Polyester Film AXIAL - Single-sided Metallized Polyester Film AXIAL - Double-sided Metallized Polyester Film Winding Scheme

© KEMET Electronics Corporation • P.O. Box 5928 • Greenville, SC 29606 (864) 963-6300 • www.kemet.com F3 096_R47_X2_440 • 6/9/2016 Metallized Polypropylene Film EMI Suppression Capacitors R47 Series, Class X2, 440 VAC, 110ºC (Automotive Grade) Marking IEC Climatic Category Approval Marks TOPFRONT Lead Spacing 10 mm Manufacturer’s Logo Manufacturing Plant IEC Climatic Category Approval Marks TOPFRONT Series Capacitance, Capacitance Tolerance, Rated Voltage Manufacturing Plant Lead Spacing 22.5 mm (large case sizes), 27.5 mm, 37.5 mm Manufacturer’s Logo Dielectric Code Safety Class Self Healing Passive Flammability Category Date Code QA Number Capacitance Tolerance Date Code Capacitance, Rated Voltage Series, Dielectric Code, Safety Class, Self Healing IEC Climatic Category Approval Marks TOPFRONT Lead Spacing 15 mm, 22.5 mm (small case sizes) Manufacturer’s Logo Passive Flammability Category Manufacturing Plant Capacitance Tolerance Date Code Capacitance, Rated Voltage Series, Dielectric Code, Safety Class, Self Healing Passive Flammability Category: B for volume ≥ 1750 mm3 C for volume < 1750 mm3

© KEMET Electronics Corporation • P.O. Box 5928 • Greenville, SC 29606 (864) 963-6300 • www.kemet.com F3 096_R47_X2_440 • 6/9/2016 Metallized Polypropylene Film EMI Suppression Capacitors R47 Series, Class X2, 440 VAC, 110ºC (Automotive Grade) Marking cont'd IEC Climatic Category Approval Marks TOPFRONT Lead Spacing 10 mm Manufacturer’s Logo Manufacturing Plant IEC Climatic Category Approval Marks TOPFRONT Series Capacitance, Capacitance Tolerance, Rated Voltage Manufacturing Plant Lead Spacing 22.5 mm (large case sizes), 27.5 mm, 37.5 mm Manufacturer’s Logo Dielectric Code Safety Class Self Healing Passive Flammability Category Date Code QA Number Capacitance Tolerance Date Code Capacitance, Rated Voltage Series, Dielectric Code, Safety Class, Self Healing IEC Climatic Category Approval Marks TOPFRONT Lead Spacing 15 mm, 22.5 mm (small case sizes) Manufacturer’s Logo Passive Flammability Category Manufacturing Plant Capacitance Tolerance Date Code Capacitance, Rated Voltage Series, Dielectric Code, Safety Class, Self Healing Passive Flammability Category: B for volume ≥ 1750 mm3 C for volume < 1750 mm3 Manufacturing Date Code (IEC 60062) Y = Year, Z = Month Year Code Month Code

2000 M January 1

2001 N February 2

2002 P March 3

2003 R April 4

2004 S May 5

2005 T June 6

2006 U July 7

2007 V August 8

2008 W September 9

2009 X October O

2010 A November N

2011 B December D

© KEMET Electronics Corporation • P.O. Box 5928 • Greenville, SC 29606 (864) 963-6300 • www.kemet.com F3 096_R47_X2_440 • 6/9/2016 Metallized Polypropylene Film EMI Suppression Capacitors R47 Series, Class X2, 440 VAC, 110ºC (Automotive Grade) Packaging Quantities Lead Spacing (mm) Thickness (mm) Height (mm) Length (mm) Bulk Short Leads Bulk Long Leads Standard Reel ø 355 mm Large Reel ø 500 mm Ammo Taped 4 9 13 2000 1800 750 1500 1000 5 11 13 1300 1500 600 1250 800 6 12 13 1000 1200 500 1000 680 5 11 18 2000 1000 600 1250 800 6 12 18 1750 900 500 1000 680 6 17.5 18 1000 700 500 1000 680 7.5 13.5 18 1000 700 350 800 500 7.5 18.5 18 900 500 – 800 500 8.5 14.5 18 1000 500 300 700 440 9 12.5 18 1000 520 270 650 410 10 16 18 750 500 300 600 380 11 19 18 450 350 – 500 340 13 12 18 750 490 200 480 280 22.5 6 15 26.5 805 500 – 700 464 7 16 26.5 700 500 – 550 380 8.5 17 26.5 468 300 – 450 280 10 18.5 26.5 396 300 – 350 235 11 20 26.5 360 250 – 350 217 13 22 26.5 300 200 – 300 – 27.5 9 17 32 816 408 – 450 – 11 20 32 560 336 – 350 – 13 22 32 480 288 – 300 – 14 28 32 352 176 – – – 18 33 32 256 128 – – – 22 37 32 168 112 – – – 37.5 11 22 41.5 420 252 – – – 13 24 41.5 360 216 – – – 16 28.5 41.5 216 108 – – – 19 32 41.5 192 96 – – – 20 40 41.5 126 84 – – –

© KEMET Electronics Corporation • P.O. Box 5928 • Greenville, SC 29606 (864) 963-6300 • www.kemet.com F3 096_R47_X2_440 • 6/9/2016 Metallized Polypropylene Film EMI Suppression Capacitors R47 Series, Class X2, 440 VAC, 110ºC (Automotive Grade) Lead Taping & Packaging (IEC 60286–2) cont'd Ammo Specifi cations Dimensions (mm) H W T 360 340 59 Reel Specifi cations Reel Size Dimensions (mm) D H W Standard 355 30 55 MaximumLarge 500 25 D W H H T W

© KEMET Electronics Corporation • P.O. Box 5928 • Greenville, SC 29606 (864) 963-6300 • www.kemet.com F3 096_R47_X2_440 • 6/9/2016 Metallized Polypropylene Film EMI Suppression Capacitors R47 Series, Class X2, 440 VAC, 110ºC (Automotive Grade) KEMET Corporation World Headquarters

2835 KEMET Way

Simpsonville, SC 29681 Mailing Address: P.O. Box 5928 Greenville, SC 29606 www.kemet.com Tel: 864-963-6300 Fax: 864-963-6521 Corporate Offi ces Fort Lauderdale, FL Tel: 954-766-2800 North America Northeast Wilmington, MA Tel: 978-658-1663 Southeast Lake Mary, FL Tel: 407-855-8886 Central Novi, MI Tel: 248-994-1030 Irving, TX Tel: 972-915-6041 West Milpitas, CA Tel: 408-433-9950 Mexico Guadalajara, Jalisco Tel: 52-33-3123-2141 Europe Southern Europe Sasso Marconi, Italy Tel: 39-051-939111 Skopje, Macedonia Tel: 389-2-55-14-623 Central Europe Landsberg, Germany Tel: 49-8191-3350800 Kamen, Germany Tel: 49-2307-438110 Northern Europe Wyboston, United Kingdom Tel: 44-1480-273082 Espoo, Finland Tel: 358-9-5406-5000 Asia Northeast Asia Hong Kong Tel: 852-2305-1168 Shenzhen, China Tel: 86-755-2518-1306 Beijing, China Tel: 86-10-5877-1075 Shanghai, China Tel: 86-21-6447-0707 Seoul, South Korea Tel: 82-2-6294-0550 Taipei, Taiwan Tel: 886-2-27528585 Southeast Asia Singapore Tel: 65-6701-8033 Penang, Malaysia Tel: 60-4-6430200 Bangalore, India Tel: 91-806-53-76817 Note: KEMET reserves the right to modify minor details of internal and external construction at any time in the interest of product improvement. KEMET does not assume any responsibility for infringement that might result from the use of KEMET Capacitors in potential circuit designs. KEMET is a registered trademark of KEMET Electronics Corporation.

© KEMET Electronics Corporation • P.O. Box 5928 • Greenville, SC 29606 (864) 963-6300 • www.kemet.com F3 096_R47_X2_440 • 6/9/2016 Metallized Polypropylene Film EMI Suppression Capacitors R47 Series, Class X2, 440 VAC, 110ºC (Automotive Grade) Disclaimer All product specifi cations, statements, information and data (collectively, the “Information”) in this datasheet are subject to change. The customer is responsible for checking and verifying the extent to which the Information contained in this publication is applicable to an order at the time the order is placed. All Information given herein is believed to be accurate and reliable, but it is presented without guarantee, warranty, or responsibility of any kind, expressed or implied. Statements of suitability for certain applications are based on KEMET Electronics Corporation’s (“KEMET”) knowledge of typical operating conditions for such applications, but are not intended to constitute – and KEMET specifi cally disclaims – any warranty concerning suitability for a specifi c customer application or use. The Information is intended for use only by customers who have the requisite experience and capability to determine the correct products for their application. Any technical advice inferred from this Information or otherwise provided by KEMET with reference to the use of KEMET’s products is given gratis, and KEMET assumes no obligation or liability for the advice given or results obtained. Although KEMET designs and manufactures its products to the most stringent quality and safety standards, given the current state of the art, isolated component failures may still occur. Accordingly, customer applications which require a high degree of reliability or safety should employ suitable designs or other safeguards (such as installation of protective circuitry or redundancies) in order to ensure that the failure of an electrical component does not result in a risk of personal injury or property damage. Although all product–related warnings, cautions and notes must be observed, the customer should not assume that all safety measures are indicted or that other measures may not be required.