R3-SDA16 MSYSTEM | Alldatasheet
Document overview
- Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
- PDF pages: 4
Technical content
MODEL: R3S-DA16 R3S-DA16 SPECIFICATIONS ES-8931 Rev.3 Page 1/4 http://www.m-system.co.jp/ Remote I/O R3 Series DISCRETE INPUT MODULE (Di 16 points; with excitation supply, tension clamp terminal block) 27.5 (1.08) 130 (5.12) 120 (4.72) mm (inch) MODEL: R3S-DA16[1][2]
ORDERING INFORMATION
- Code number: R3S-DA16[1][2] Specify a code from below for each of [1] and [2]. (e.g. R3S-DA16W/Q)
- Specify the specification for option code /Q (e.g. /C01) NO. OF CHANNELS 16: 16 [1] COMMUNICATION MODE S: Single W: Dual [2] OPTIONS blank: none /Q: Options other than the above (specify the specification) SPECIFICATIONS OF OPTION: Q COATING (For the detail, refer to M-System's web site.) /C01: Silicone coating /C02: Polyurethane coating /C03: Rubber coating GENERAL SPECIFICATIONS Connection Internal bus: Via the Installation Base (model: R3-BSx) Input: Separable tension clamp terminal (applicable wire size: 0.2 to 1.5 mm2, stripped length 10 mm) Internal power: Via the Installation Base (model: R3-BSx) Isolation: Input to internal bus or internal power Excitation monitor: Selectable with side DIP switch; ON/OFF setting available RUN indicator: Bi-color (red/green) LED; Red when the bus A operates normally; Green when the bus B operates normally; Amber when both buses operate normally. ERR indicator: Bi-color (red/green) LED; Red with excitation abnormality; Green in normal operating conditions. Input status indicator: Red LED; turns on with the input ON. Read rate: 1 / 5 / 10 / 20 / 50 / 70 / 100 / 200 msec. selectable with DIP SW INPUT SPECIFICATIONS Number of input: 16 points Isolation: Optical isolator, transformer (internal power supply) Input resistance: Approx. 5.9 kΩ Common: Negative common per 16 points (20 terminals) Sensing: 13 V DC ON current/resistance: ≥ 1.5 mA (≤ 1.5 kΩ) OFF current/resistance: ≤ 0.75 mA (≥ 18 kΩ) Detection levels ON: ≥ 10 V OFF: ≤ 4 V INSTALLATION Operating temperature: -10 to +55°C (14 to 131°F) Operating humidity: 30 to 90 %RH (non-condensing) Atmosphere: No corrosive gas or heavy dust Mounting: Installation Base (model: R3-BSx) Weight: 200 g (0.44 lb) PERFORMANCE Data allocation: 1 Current consumption: 100 mA Insulation resistance: ≥ 100 MΩ with 500 V DC Dielectric strength: 2000 V AC @ 1 minute (input to internal bus or internal power)
2000 V AC @ 1 minute (power input to FG; isolated on the
power supply module) FUNCTIONS ■ EXCITATION MONITOR Enabled/disabled with DIP switch setting.
- Excitation Monitor ON The input is held at the last status when the loss of excitation is detected.
- Excitation Monitor OFF
MODEL: R3S-DA16 R3S-DA16 SPECIFICATIONS ES-8931 Rev.3 Page 2/4 http://www.m-system.co.jp/ All input signals are turned off when the loss of excitation is detected. EXTERNAL VIEW RUN LED ERR LED Status Indicator LED ■ FRONT VIEW ■ SIDE VIEW SW3 ON Functions Exc. Monitor Read Rate EXTERNAL DIMENSIONS unit: mm (inch) 130 (5.12) 120 (4.72) POSITIONING GUIDE
MODEL: R3S-DA16 R3S-DA16 SPECIFICATIONS ES-8931 Rev.3 Page 3/4 http://www.m-system.co.jp/ SCHEMATIC CIRCUITRY & CONNECTION DIAGRAM Comm. Circuit Numbers in italic indicate LED No.s assigned to the front panel LEDs. * For dual redundant communication. Control Circuit ERR LED RUN LED STATUS INDICATOR LED Di 1 Di 2 Di 3 Di 4 Di 5 Di 6 Di 7 Di 8 Di 9 Di 10 Di 11 Di 12 Di 13 Di 14 Di 15 Di 16 DIP SW BUS CONNECTOR Input Circuit INTERNAL POWER INTERNAL BUS A INTERNAL BUS B *
MODEL: R3S-DA16 R3S-DA16 SPECIFICATIONS ES-8931 Rev.3 Page 4/4 http://www.m-system.co.jp/ Di 1 Di 16 Excitation supply ■ Input Circuit Control Circuit INPUT TERMINAL ASSIGNMENT PIN No. FUNCTION PIN No. FUNCTION 21 0V 1 Di1 22 0V 2 Di2 23 0V 3 Di3 24 0V 4 Di4 25 0V 5 Di5 26 0V 6 Di6 27 0V 7 Di7 28 0V 8 Di8 29 0V 9 NC 30 0V 10 NC 31 0V 11 Di9 32 0V 12 Di10 33 0V 13 Di11 34 0V 14 Di12 35 0V 15 Di13 36 0V 16 Di14 37 0V 17 Di15 38 0V 18 Di16 39 0V 19 NC 40 0V 20 NC Specifications are subject to change without notice.