QME48T20120

QME48T20120 BEL | Alldatasheet

Document overview

• Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
• PDF pages: 15

Technical content

The QME48T20120 converter of the QME-Series provides outstanding thermal performance in high temperature environments. This performance is accomplished through the use of patented/patent - pending circuits, packaging, and processing techniques to achieve ultra-high efficiency, excellent thermal management, and a low -body profile. The low -body profile and the preclusion of heat sinks minimiz e impedance to system airflow, thus enhancing cooling for both upstream and downstream devices. The use of 100% automation for assembly, coupled with advanced electronic circuits and thermal design, results in a product with extremely high reliability. Operating from a 36 -75 V input, the QME-Series converters provide outputs that can be trimmed from –20% to +10% of the nominal output voltage, thus providing outstanding design flexibility.

• 36-75 VDC Input; 12 VDC @ 20 A Output
• On-board input differential LC-filter
• Startup into pre-biased load
• No minimum load required
• Withstands 100 V input transient for 100 ms
• Fixed-frequency operation
• Remote output sense
• Fully protected with automatic recovery
• Positive or negative logic ON/OFF option
• High reliability: MTBF approx. 8.7 million hours, calculated per Telcordia TR-332, Method I Case 1
• Approved to the latest edition and amendment of ITE Safety standards, UL/CSA 60950-1 and IEC60950-1
• RoHS lead free solder and lead-solder-exempted products are available

2 QME48T20120

tech.support@psbel.com Stresses in excess of the absolute maximum ratings may cause performance degradation, adversely affect long-term reliability, and cause permanent damage to the converter. Input Voltage Continuous 0 80 VDC Operating Ambient Temperature -40 85 C Storage Temperature -55 125 C Conditions: TA = 25ºC, Airflow = 300 LFM (1.5 m/s), Vin = 48 VDC, unless otherwise specified. Output Voltage Set Point (no load) 11.88 12.00 12.12 VDC Output Regulation Over Line ±4 ±10 mV Over Load ±4 ±10 mV Output Voltage Range Over line, load and temperature (-40ºC to 85ºC) 11.76 12.24 VDC Output Ripple and Noise (25 MHz bandwidth) Full load + 10 µF tantalum + 1 µF ceramic 60 120 mVPK-PK External Load Capacitance Plus full load (resistive) 2200 µF Output Current Range 0 20 ADC Current Limit Inception Non-latching 22 24 26.6 ADC Peak Short-Circuit Current Non-latching, Short = 10 mΩ 50 A RMS Short-Circuit Current Non-latching 5 Arms Dynamic Response Load Change 50%-75%-50%, di/dt = 0.1 A/µs, Co = 1 µF ceramic 50 mV di/dt = 5 A/µs, Co = 470 µF POS + 1 µF ceramic 120 mV Settling Time to 1% 30 µs Efficiency 100% Load 93 % 50% Load 94 %

2.1 INPUT SPECIFICATIONS

Operating Input Voltage Range 36 48 75 VDC Input Under Voltage Lockout (Non-latching) Turn-on Threshold 33 34 35 VDC Turn-off Threshold 31 32 33 VDC Input Voltage Transient 100 ms 100 VDC Maximum Input Current 20 ADC, 12 VDC Out @ 36 VDC In 7.5 ADC Input Stand-by Current Vin = 48 V, converter disabled 3 mADC Input No Load Current (0 load on the output) Vin = 48 V, converter enabled 69 mADC Input Reflected-Ripple Current 25 MHz bandwidth 20 mAPK-PK Input Voltage Ripple Rejection 120 Hz 65 dB

2.2 OUTPUT SPECIFICATIONS

+86 755 298 85888 Europe, Middle East +353 61 225 977 North America +1 408 785 5200 © 2018 Bel Power Solutions & Protection BCD.00713_AC Dimensions 36.83 x 58.42 x 12.24 1.45 x 2.30 x 0.482 mm inch Weight 1.25 35.85 oz g MTBF Calculated per Telcordia TR-332, Method I Case 1 8.7 million hours Flammability All materials meet UL94, V-0 flammability rating 1 Vout can be increased up to 10% via the sense leads or up to 10% via the trim function. However, the total output voltage tri m from all sources should not exceed 10% of VOUT(NOM), in order to ensure specified operation of overvoltage protection circuitry. Switching Frequency 380 kHz Output Voltage Trim Range1 Industry-std. equations -20 +10 % Remote Sense Compensation1 Percent of VOUT(NOM) +10 % Output Overvoltage Protection Non-latching 117 122 127 % Overtemperature Shutdown (PCB) Non-latching 125 °C Auto-Restart Period Applies to all protection features 200 ms Turn-On Time 4 ms ON/OFF Control (Positive Logic) Converter Off (logic low) -20 0.8 VDC Converter On (logic high) 2.4 20 VDC ON/OFF Control (Negative Logic) Converter Off (logic high) 2.4 20 VDC Converter On (logic low) -20 0.8 VDC I/O Isolation 2000 VDC Isolation Capacitance 3 ηF Isolation Resistance 10 MΩ

4 QME48T20120

tech.support@psbel.com These power converters have been designed to be stable with no external capacitors when used in low inductance input and output circuits. In many applications, the inductance associated with the distribution from the power source to the input of the conve rter can affect the stability of the converter. The addition of a 100 µF electrolytic capacitor with an ESR < 1 Ω across the input helps to ensure stability of the converter. In many applications, the user has to use decoupling capacitance at the load. The power converter will exhibit stable operation with external load capacitance up to 2,200 µF on 12 V output. Additionally, see the EMC section of this data sheet for discussion of other external components which may be required for control of conducted emissions. The ON/OFF pin is used to turn the power converter on or off remotely via a system signal. There are two remote control options available, positive and negative logic, with both referenced to Vin(-). A typical connection is shown in Fig. A. Figure A. Circuit configuration for ON/OFF function. The positive logic version turns on when the ON/OFF pin is at a logic high and turns off when at a logic low. The converter i s on when the ON/OFF pin is left open. See the Electrical Specifications for logic high/low definitions. The negative logic version turns on when the pin is at a logic low and turns off when the pin is at a logic high. The ON/OFF pin can be hardwired directly to Vin( -) to enable automatic power up of t he converter without the need of an external control signal. The ON/OFF pin is internally pulled up to 5 V through a resistor. A properly debounced mechanical switch, open -collector transistor, or FET can be used to drive the input of the ON/OFF pin. The device must be capable of sinking up to 0.2 mA at a low level voltage of  0.8 V. An external voltage source (±20 V maximum) may be connected directly to the ON/OFF input, in which case it must be capable of sourcing or sinking up to 1 mA depending on the signal polarity. See the Startup Information section for system timing waveforms associated with use of the ON/OFF pin. The remote sense feature of the converter compensates for voltage drops occurring between the output pins of the converter and the load. The SENSE(-) (Pin 5) and SENSE(+) (Pin 7) pins should be connected at the load or at the point where regulation is required (see Fig. B). Figure B. Remote sense circuit configuration. Rload Vin CONTROL INPUT Vin (+) Vin (-) ON/OFF Vout (+) Vout (-) TRIM SENSE (+) SENSE (-) (Top View) Converter QME Series 100 Rw Rw Rload Vin Vin (+) Vin (-) ON/OFF Vout (+) Vout (+) TRIM SENSE (+) SENSE (-) (Top View) Converter QME Series

+86 755 298 85888 Europe, Middle East +353 61 225 977 North America +1 408 785 5200 © 2018 Bel Power Solutions & Protection BCD.00713_AC CAUTION If remote sensing is not utilized, the SENSE (-) pin must be connected to the Vout(-) pin (Pin 4), and the SENSE(+) pin must be connected to the Vout(+) pin (Pin 8) to ensure the converter will regulate at the specified output voltage. If these connections are not made, the converter will deliver an output voltage that is slightly higher than the specified data sheet value. Because the sense leads carry minimal current, large traces on the end -user board are not required. However, sense traces should be run side by side and located close to a ground plane to minimize system noise and ensure optimum performance. The converter’s output overvoltage protection (OVP) senses the voltage across Vout(+) and Vout(-), and not across the sense lines, so the resistance (and resulting voltage drop) between the output pins of the converter and the load should be minimized to prevent unwanted triggering of the OVP. When utilizing the remote sense feature, care must be taken not to exceed the maximum allowable out put power capability of the converter, which is equal to the product of the nominal output voltage and the allowable output current for the given conditions. When using remote sense, the output voltage at the converter can be increased by as much as 10% above the nominal rating in order to maintain the required voltage across the load. Therefore, the designer must, if necessary, decrease the maximum current (originally obtained from the derating curves) by the same percentage to ensure the converter’s actua l output power remains at or below the maximum allowable output power. The output voltage can be adjusted up 10% or down 20% relative to the rated output voltage by the addition of an externally connected resistor. Trim up to 10% at full load is guaranteed at Vin ≥ 40V. The TRIM pin should be left open if trimming is not bein g used. To minimize noise pickup, a 0.1 µF capacitor is connected internally between the TRIM and SENSE(-) pins. To increase the output voltage, refer to Fig. C. A trim resistor, R T-INCR, should be connected between the TRIM (Pin 6) and SENSE(+) (Pin 7), with a value of: 10.221.225Δ 626Δ)V5.11(100R NOMO INCRT  [kΩ] where, INCRTR Required value of trim-up resistor [kΩ] NOMOV Nominal value of output voltage [V] 100XV )V(V Δ NOM- O NOM-OREQ-O  [%] REQOV Desired (trimmed) output voltage [V]. When trimming up, care must be taken not to exceed the converter‘s maximum allowable output power. See the previous section for a complete discussion of this requirement. Figure C. Configuration for increasing output voltage. To decrease the output voltage (Fig. D), a trim resistor, R T-DECR, should be connected between the TRIM (Pin 6) and SENSE( -) (Pin 5), with a value of: Rload Vin Vin (+) Vin (-) ON/OFF Vout (+) Vout (-) TRIM SENSE (+) SENSE (-) R T-INCR (Top View) Converter QME Series

6 QME48T20120

tech.support@psbel.com 10.22|Δ| 511R DECRT  [kΩ] where, DECRTR Required value of trim-down resistor [kΩ] and Δ is defined above. Note: The above equations for calculation of trim resistor values match those typically used in conventional industry -standard quarter-bricks. Figure D. Configuration for decreasing output voltage. Trimming/sensing beyond 110% of the rated output voltage is not an acceptable design practice, as this condition could cause unwanted triggering of the output overvoltage protection (OVP) circuit. The designer should ensure that the difference between the voltages across the converter’s output pins and its sense pins does not exceed 10% of VOUT(nom), or: X NOM-O SENSESENSEOUTOUT 10%V)](V)(V)([V  [V] This equation is applicable for any condition of output sensing and/or output trim. Input undervoltage lockout is standard with this converter. The converter will shut down when the input voltage drops below a pre-determined voltage. The input voltage must be typically 34 V for the converter to turn on. Once the converter has been turned on, it will shut off when the input voltage drops typically below 32 V. This feature is beneficial in preventing deep discharging of batteries used in telecom applications. The converter is protected against overcurrent or short circuit conditions. Upon sensing an overcurrent condition, the converter will switch to constant current operation and thereby begin to reduce output voltage. When the output voltage drops below 60% of the nominal value of output voltage, the converter will shut down. Once the converter has shut down, it will attempt to restart nominally every 100 ms with a typical 3 -5% duty cycle. The attempted restart will continue indefinitely until the overload or short circuit conditions are remove d or the output voltage rises above 60% of its nominal value. Once the output current is brought back into its specified range, the converter automatically exits the hiccup mode and continues normal operation. The converter will shut down if the output voltage across Vout(+) (Pin 8) and Vout(-) (Pin 4) exceeds the threshold of the OVP circuitry. The OVP circuitry contains its own reference, independent of the output voltage regulation loop. Once the converter has shut down, it will attempt to restart every 200 ms until the OVP condition is removed. Rload Vin Vin (+) Vin (-) ON/OFF Vout (+) Vout (-) TRIM SENSE (+) SENSE (-) RT-DECR (Top View) Converter QME Series

+86 755 298 85888 Europe, Middle East +353 61 225 977 North America +1 408 785 5200 © 2018 Bel Power Solutions & Protection BCD.00713_AC The converter will shut down under an overtemperature condition to protect itself from overheating caused by operation outside the thermal derating curves, or operation in abnormal conditions such as system fan failure. After the converter has cooled to a safe operating temperature, it will automatically restart. The converters are safety approved to UL/CSA60950-1, EN60950-1, and IEC60950-1. Basic Insulation is provided between input and output. To comply with safety agencies’ requirements, an input line fuse must be used external to the converter. A 15 A fuse is recommended for use with this product. All QME converters are UL approved for a maximum fuse rating of 15 Amps. To protect a group of converters with a single fuse, the rating can be increased from the recommended value above. EMC requirements must be met at the end-product system level, as no specific standards dedicated to EMC characteristics of board mounted component dc-dc converters exist. However, Bel Power Solutions tests its converters to several system level standards, primary of which is the more stringent EN55022, Information technology equipment - Radio disturbance characteristics-Limits and methods of measurement. An effective internal LC differential filter significantly reduces input reflected ripple current, and improves EMC. With the addition of a simple external filter, all versions of the QME -Series of converters pass the requirements of Class B conducted emissions per EN55022 and FCC requirements. Please contact Bel Power Solutions Applications Engineering for details of this testing. Scenario #1: Initial Startup From Bulk Supply ON/OFF function enabled, converter started via application of VIN. See Figure E. Time Comments t0 ON/OFF pin is ON; system front end power is toggled on, VIN to converter begins to rise. t1 VIN crosses undervoltage Lockout protection circuit threshold; converter enabled. t2 Converter begins to respond to turn-on command (converter turn-on delay). t3 Converter VOUT reaches 100% of nominal value. For this example, the total converter startup time (t3- t1) is typically 4 ms. Figure E. Startup scenario #1. Scenario #2: Initial Startup Using ON/OFF Pin With VIN previously powered, converter started via ON/OFF pin. See Figure F. Time Comments t0 VINPUT at nominal value. t1 Arbitrary time when ON/OFF pin is enabled (converter enabled). t2 End of converter turn-on delay. t3 Converter VOUT reaches 100% of nominal value. For this example, the total converter startup time (t3- t1) is typically 4 ms. Figure F. Startup scenario #2. VIN ON/OFF STATE VOUT t t0 t1 t2 t3 ON OFF ON/OFF STATE VOUT t0 t1 t2 t3 ON OFF VIN t

8 QME48T20120

tech.support@psbel.com Scenario #3: Turn-off and Restart Using ON/OFF Pin With VIN previously powered, converter is disabled and then enabled via ON/OFF pin. See Figure G. Time Comments t0 VIN and VOUT are at nominal values; ON/OFF pin ON. t1 ON/OFF pin arbitrarily disabled; converter output falls to zero; turn-on inhibit delay period (200 ms typical) is initiated, and ON/OFF pin action is internally inhibited. t2 ON/OFF pin is externally re-enabled. If (t2- t1) ≤ 200 ms, external action of ON/OFF pin is locked out by startup inhibit timer. If (t2- t1) > 200 ms, ON/OFF pin action is internally enabled. t3 Turn-on inhibit delay period ends. If ON/OFF pin is ON, converter begins turn-on; if off, converter awaits ON/OFF pin ON signal; see Figure F. t4 End of converter turn-on delay. t5 Converter VOUT reaches 100% of nominal value. For the condition, (t2- t1) ≤ 200 ms, the total converter startup time (t5- t2) is typically 204 ms. For (t2- t1) > 200 ms, startup will be typically 4 ms after release of ON/OFF pin. Figure G. Startup scenario #3. The converter has been characterized for many operational aspects, to include thermal derating (maximum load current as a function of ambient temperature and airflow) for vertical and horizontal mountings, efficiency, startup and shutdown parameters, output ripple and noise, transient response to load step-change, overload, and short circuit. The following pages contain specific plots or waveforms associated with the converter. Additional comments for specific data are provided below. All data presented were taken with the converter soldered to a test board, specifically a 0.060” thick printed wiring board (PWB) with four layers. The top and bottom layers were not metalized. The two inner layers, comprised of two-ounce copper, were used to provide traces for connectivity to the converter. The lack of metalizat ion on the outer layers as well as the limited thermal connection ensured that heat transfer from the converter to the PWB was minimized. This provides a worst-case but consistent scenario for thermal derating purposes. All measurements requiring airflow w ere made in the vertical and horizontal wind tunnel using Infrared (IR) thermography and thermocouples for thermometry. Ensuring components on the converter do not exceed their ratings is important to maintaining high reliability. If one anticipates operating the converter at or close to the maximum loads specified in the derating curves, it is prudent to check actual operating temperatures in the application. Thermographic imaging is preferable; if this capability is not available, then thermocouples may be used. The use of AWG #40 gauge thermocouples is recommended to ensure measurement accuracy. Careful routing of the thermocouple leads will further minimize measurement error. Refer to Fig. H for the optimum measuring thermocouple location. ON/OFF STATE OFF ON V OUT t t t t V IN t t 200 ms

+86 755 298 85888 Europe, Middle East +353 61 225 977 North America +1 408 785 5200 © 2018 Bel Power Solutions & Protection BCD.00713_AC Fig. H: Location of the thermocouple for thermal testing. Load current vs. ambient temperature and airflow rates are given in Fig. 1 and Fig. 2 for vertical and horizontal converter mountings. Ambient temperature w as varied between 25 °C and 85 °C, with airflow rates from 30 to 500 LFM (0.15 to 2.5 m/s). For each set of conditions, the maximum load current was defined as the lowest of: (i) The output current at which any FET junction temperature does not exceed a maximum specified temperature of 125 °C as indicated by the thermographic image, or (ii) The nominal rating of the converter (20 A). During normal operation, derating curves with maximum FET temperature less or equal to 125 °C should not be exceeded. Temperature at the thermocouple location shown in Fig. H should not exceed 125 °C in order to operate inside the derating curves. Fig. 3 shows the efficiency vs. load current plot for ambient temperature of 25 ºC, airflow rate of 300 LFM (1.5 m/s) with vertical mounting and input voltages of 36 V, 48 V and 72 V. Also, a plot of efficiency vs. load current, as a function of ambient temperature with Vin = 48 V, airflow rate of 200 LFM (1 m/s) with vertical mounting is shown in Fig. 4. Fig. 5 shows the power dissipation vs. load current plot for Ta = 25 ºC, airflow rate of 300 LFM (1.5 m/s) with vertical mounting and input voltages of 36 V, 48 V and 72 V. Also, a plot of power dissipation vs. load current, as a function of ambient temperature with Vin = 48 V, airflow rate of 200 LFM (1 m/s) with vertical mounting is shown in Fig. 6. Output voltage waveforms, during the turn-on transient using the ON/OFF pin for full rated load currents (resistive load) are shown without and with external load capacitance in Figs. 7-8, respectively. Fig. 11 show the output voltage ripple waveform, measured at full rated load current with a 10 µF tantalum and 1 µF ceramic capacitor across the output. Note that all output voltage waveforms are measured across a 1 µF ceramic capacitor. The input reflected ripple current waveforms are obtained using the test setup shown in Fig 12. The corresponding waveforms are shown in Figs. 13-14.

10 QME48T20120

tech.support@psbel.com Ambient Temperature [°C] 20 30 40 50 60 70 80 90 Load Current [Adc] 500 LFM (2.5 m/s) 400 LFM (2.0 m/s) 300 LFM (1.5 m/s) 200 LFM (1.0 m/s) 100 LFM (0.5 m/s) 30 LFM (0.15 m/s) Ambient Temperature [°C] 20 30 40 50 60 70 80 90 Load Current [Adc] 500 LFM (2.5 m/s) 400 LFM (2.0 m/s) 300 LFM (1.5 m/s) 200 LFM (1.0 m/s) 100 LFM (0.5 m/s) 30 LFM (0.15 m/s) Fig. 1 : Available load current vs. ambient air temperature and airflow rates for converter with G height pins mounted vertically with air flowing from pin 1 to pin 3, MOSFET temperature  125 C, Vin = 48 V. Fig. 2: Available load current vs. ambient air temperature and airflow rates for converter with G height pins mounted horizontally with air flowing from pin 1 to pin 3, MOSFET temperature  125 C, Vin = 48 V. Load Current [Adc] 0 4 8 12 16 20 24 Efficiency 0.70 0.75 0.80 0.85 0.90 0.95 1.00 72 V 48 V 36 V Load Current [Adc] 0 4 8 12 16 20 24 Efficiency 0.75 0.80 0.85 0.90 0.95 1.00 70 C 55 C 40 C Fig. 3: Efficiency vs. load current and input voltage for converter mounted vertically with air flowing from pin 1 to pin 3 at a rate of 300 LFM (1.5 m/s) and Ta = 25 C. Fig. 4: Efficiency vs. load current and ambient temperature for converter mounted vertically with Vin = 48 V and air flowing from pin 1 to pin 3 at a rate of 200 LFM (1.0 m/s). Load Current [Adc] 0 4 8 12 16 20 24 Power Dissipation [W] 0.00 5.00 10.00 15.00 20.00 25.00 72 V 48 V 36 V Load Current [Adc] 0 4 8 12 16 20 24 Power Dissipation [W] 0.00 5.00 10.00 15.00 20.00 25.00 70 C 55 C 40 C Fig. 5: Power dissipation vs. load current and input voltage for converter mounted vertically with air flowing from pin 1 to pin 3 at a rate of 300 LFM (1.5 m/s) and Ta = 25 C. Fig. 6: Power dissipation vs. load current and ambient temp. for converter mounted vertically with Vin = 48 V and air flowing from pin 1 to pin 3 at a rate of 200 LFM (1.0 m/s).

+86 755 298 85888 Europe, Middle East +353 61 225 977 North America +1 408 785 5200 © 2018 Bel Power Solutions & Protection BCD.00713_AC Fig. 7: Turn-on transient at full rated load current (resistive) with no output capacitor at Vin = 48 V, triggered via ON/OFF pin. Top trace: ON/OFF signal (5 V/div.). Bottom trace: output voltage (2 V/div.). Time scale: 2 ms/div. Fig. 8: Turn-on transient at full rated load current (resistive) plus 2,200 µF at Vin = 48 V, triggered via ON/OFF pin. Top trace: ON/OFF signal (5 V/div.). Bottom trace: output voltage (5 V/div.). Time scale: 2 ms/div. Fig. 9: Output voltage response to load current step-change (10 A – 15 A – 10 A) at Vin = 48 V. Top trace: output voltage (100 mV/div.). Bottom trace: load current (5 A/div.). Current slew rate: Fig. 10: Output voltage response to load current step-change (10 A – 15 A – 10 A) at Vin = 48 V. Top trace: output voltage (100 mV/div.). Bottom trace: load current (5 A/div.). Current slew rate: 5 A/µs. Co = 470 µF POS + 1 µF ceramic. Time scale: 0.2 ms/div. Fig. 11: Output voltage ripple (50 mV/div.) at full rated load current into a resistive load with Co = 10 µF tantalum + 1 µF ceramic and Vin = 48 V. Time scale: 1 µs/div. Fig. 12: Test setup for measuring input reflected-ripple currents, ic and is. Vout Vsource iS iC 1 F ceramic capacitor 10 H source inductance DC/DC Converter 33 F ESR <1 electrolytic capacitor QME Series

12 QME48T20120

tech.support@psbel.com Fig. 13: Input reflected ripple current, ic (500 mA/div.), measured at input terminals at full rated load current and Vin = 48 V. Refer to Fig. 12 for test setup. Time scale: 1 µs/div. Fig. 14: Input reflected ripple current, is (10 mA/div.), measured through 10 µH at the source at full rated load current and Vin = 48 V. Refer to Fig. 12 for test setup. Time scale: 1 µs/div. Fig. 15: Output voltage vs. load current showing current limit point and converter shutdown point. Input voltage has almost no effect on current limit characteristic. Fig. 16: Load current (top trace, 20 A/div., 50 ms/div.) into a 10 mΩ short circuit during restart, at Vin = 48 V. Bottom trace (20 A/div., 2 ms/div.) is an expansion of the on-time portion of the top trace. Iout [Adc] 8 32 16.0 Vout [Vdc] 8.0 4.0 16 24 12.0

+86 755 298 85888 Europe, Middle East +353 61 225 977 North America +1 408 785 5200 © 2018 Bel Power Solutions & Protection BCD.00713_AC PAD / PIN CONNECTIONS Pad/Pin # Function

1 Vin (+)

2 ON/OFF

3 Vin (-)

4 Vout (-)

5 SENSE(-)

6 TRIM

7 SENSE(+)

8 Vout (+)

(Max. Height) CL (Min. Clearance) +0.000 [+0.00] -0.038 [- 0.97] +0.016 [+0.41] -0.000 [- 0.00]

• All dimensions are in inches [mm]
• Pins 1-3 and 5-7 are Ø 0.040” [1.02] without shoulder
• Pins 4 and 8 are Ø 0.062” [1.57] without shoulder
• Pin Material & Finish: Brass Alloy 360 with Matte Tin over Nickel Pin Option PL Pin Length ±0.005 [±0.13] A 0.188 [4.78] B 0.145 [3.68] PAD / PIN CONNECTIONS Pad/Pin # Pad/Pin #

(Max. Height) CL (Min. Clearance) +0.000 [+0.00] -0.038 [- 0.97] +0.016 [+0.41] -0.000 [- 0.00] Pin Option PL Pin Length ±0.005 [±0.13] A 0.188 [4.78]

• All dimensions are in inches [mm]
• Pins 1-3 are Ø 0.040” [1.02] with Ø 0.078” [1.98] shoulder
• Pins 4 and 8 are Ø 0.062” [1.57] with Ø 0.096” [2.44] shoulder
• Pin Material: Pins 1-3 Brass Alloy 360, Pins 4 and 8 – Copper Alloy CDA 145
• Pin Finish - Matte Tin over Nickel SIDE VIEW TOP VIEW

14 QME48T20120

tech.support@psbel.com PAD / PIN CONNECTIONS Pad/Pin # Function (Max. Height) CL (Min. Clearance) +0.000 [+0.00] -0.038 [- 0.97] +0.016 [+0.41] -0.000 [- 0.00]

• All dimensions are in inches [mm]
• Pins 1-3 and 5-7 are Ø 0.040” [1.02] without shoulder
• Pins 4 and 8 are Ø 0.062” [1.57] without shoulder
• Pin Material & Finish: Brass Alloy 360 with Matte Tin over Nickel Pin Option PL Pin Length ±0.005 [±0.13] A 0.188 [4.78] B 0.145 [3.68]

+86 755 298 85888 Europe, Middle East +353 61 225 977 North America +1 408 785 5200 © 2018 Bel Power Solutions & Protection BCD.00713_AC PRODUCT SERIES INPUT VOLTAGE MOUNTING SCHEME RATED LOAD CURRENT OUTPUT VOLTAGE ON/OFF LOGIC MAXIMUM HEIGHT [HT] PIN LENGTH [PL] SPECIAL

FEATURES

QME 48 T 20 120 - N G B x y Quarter- Brick Format 36-75 V Through- hole

20 A 120  12 V

N  Negative P  Positive G  0.482” A  0.188” B  0.145” 0  Standard T  No sense and trim pins (pins 5-7), pins 4 and 8 are Ø 0.062” with Ø 0.096” shoulder W  Straight 0.040” and 0.062” pins with Ø 0.140” and Ø 0.150” plastic standoffs C Conformal Coating No Suffix Character  RoHS lead- solder- exempt compliant G  RoHS compliant for all six substances Example: QME48T20120-NGB0: 36-75 V input, through-hole mounting, 20 A @ 12 V output, negative ON/OFF logic, a maximum height of 0.482”, a through the board pin length of 0.145”, and RoHS lead-solder-exempt compliant. Please consult factory for the complete list of available options. Attention: Special features option “T” is only available with the 0.188” pin length Note: Conformal Coating Material used is compliant to IPC-CC-830 Rev B or similar and the acceptance are referring to IPC-610 Industrial Standard NUCLEAR AND MEDICAL APPLICATIONS - Products are not designed or intended for use as critical components in life support systems, equipment used in hazardous environments, or nuclear control systems. TECHNICAL REVISIONS - The appearance of products, including safety agency certifications pictured on labels, may change depending on the date manufactured. Specifications are subject to change without notice.