DATASHEET SEARCH SITE | WWW.ALLDATASHEET.COM

Document overview

  • Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
  • PDF pages: 6

Technical content

10W 5V Snap-in USB Type C Power Supply Receptacle Qualtek P/N: QKRC-10-05 :NOISIVER PREPARED: R. J. N APPROVED: L. J. Y DATE: 2021-11-11

1 GENERAL

1.1 Description

This specification defines the performance characteristics for a class adapter, single-phase 10.0 watts. Single output level power supply. Simple design philosophy. Reliability level of 50K hours MTBF @ 25 C (rated input voltage, and using the BELLCORE SR-332 method). DC output voltage must be Safe Extra Low Voltage (SELV) & Limited Power as defined by IEC62368-1. The maximum room ambient temperature (Tmra), as mentioned in clause B.1.6 and B.2.6 of IEC62368-1, for the external power supply is 40 °C.

  • Cooling: natural convection.

2 INPUT REQUIREMENTS

2.1 Input Conditions

The supply shall operate over the voltage ranges as follows: caV021-001 egatlov tupni detaR caV231-09 egnar gnitarepO zH3 -/+ zH06/05 ycneuqerf tupni detaR .xam A4.0 tnerruc tupni detaR .xam W1.0 )gnidaol-on( noitpmusnoc rewoP Primary current protection An adequate internal fuse on the AC input line is provide. rotcudnoC 2 noitarugifnoC

2.2 AC Inrush Current

No damage shall be occurred and the input fuse shall not be blown up nominal input voltage full load 25 C cold starts.

3 OUTPUT REQUIREMENTS

V0.5+ egatlov tuptuo CD lanimoN 1.3 A10.0 tnerruc daol muminiM 2.3 A0.2 tnerruc daol gnitaR 3.3 / tnerruc daol kaeP 4.3 3.5 W0.01 rewop tuptuo gnitaR

3.6 Line regulation The line regulation is less than ±5% while measuring at rated load and

+/-10% of input voltage changing. 3.7 Load regulation The load regulation for +5.0V is less than ±5%, at measured output load from 10% to 100% rated load . Qualtek

3.8 Peak load regulation The peak load regulation for +5.0V is less than / , at measured output load from 30% to 100% rated load.

3.9 Ripple and noise

Add 0.1uF/50V ceramic capacitor and 10uF/50V aluminum electrolytic capacitor across the output terminal. Measured with 20MHz Bandwidth Oscilloscope. 3.10 Switching efficiency 78.7% minimum 115V/60Hz, output current from 100%, 75%, 50%, 25%.

3.11 Turn on delay time 3000 mS max at nominal input AC voltage and full load

3.12 Rise time The supply shall have a start-up rise time of less than 20mS to rise to within

regulation limits for all DC outputs. 3.13 Hold up time 8 mS minimum at nominal input 100Vac minimum voltage and full load.

3.14 Output over-shoot Less than 10% of nominal voltage value

3.15 LED indication function /

3.16 Protection function

The adapter shall not be damaged by short the DC output to Ground. The adapter shall resume normal operation when a short circuited fault condition is removed. Over current protection The output shall be protected against the over current conditions.

4 MECHANICAL

4.1 Enclosure and Layout

Plastic case: UL94V-0 Weight : / g (Max.) Dimensions: 27.0x27.0x25.0mm Color : Black

4.2 Input and Output Configuration

Input pin: In ternational Pin Output connector : DC plug type: Type-C Polarity: / 10W 5V Snap-in USB Type C Power Supply Receptacle Qualtek P/N: QKRC-10-05 Qualtek :NOISIVER PREPARED: R. J. N APPROVED: L. J. Y DATE: 2021-11-11

5 REGULATORY COMPLIANCE

5.1 Safety Requirements and Certification

5.1.1 Regulatory Standard

The power supply shall complied the following international regulatory standards Approval Country Standard UL USA UL 62368-1 CUL Canada CSA C22.2 NO.62368-1

5.1.2 Additional Safety Requirements

Dielectric Withstand Voltage, Primary(input AC short)-to-Secondary(output DC short): 3000Vac, 5m A, 1 minute. In sulation Resistance, Input to output: 10M (MIN.) at 500VDC. Reinforced insulation system, Primary-to-Ground and Primary-to-Secondary. The leakage current shall not exceed 0.25mA.

6 ENVIRONMENTAL REQUIREMENTS

6.1 Temperature

Operating: 0 oC +40 oC Non-Operating: -25 oC +70 oC

6.2 Humidity

Operating: 10%~90% (Non Condensing) Non-Operating: 10%~90% (Non Condensing) 10W 5V Snap-in USB Type C Power Supply Receptacle Qualtek P/N: QKRC-10-05 Qualtek :NOISIVER PREPARED: R. J. N APPROVED: L. J. Y DATE: 2021-11-11

7 APPEARANCE DRAWING: (Unit: mm)

NOTE: 1. Case cover & chassis material: PC: BLACK 2. AC PIN MATERIAL: BRASS (NI PLATED) 3. Panel Thickness: 0.8~1.8mm 10W 5V Snap-in USB Type C Power Supply Receptacle Qualtek P/N: QKRC-10-05 Qualtek :NOISIVER PREPARED: R. J. N APPROVED: L. J. Y DATE: 2021-11-11

8 NAME PLATE:

Note: 1. Laser Date code(PXXYY: P=PAHS+REACH+ROHS, XX=Week, YY=Year) 10W 5V Snap-in USB Type C Power Supply Receptacle Qualtek P/N: QKRC-10-05 Qualtek :NOISIVER PREPARED: R. J. N APPROVED: L. J. Y DATE: 2021-11-11

9 AC Cable

10W 5V Snap-in USB Type C Power Supply Receptacle Qualtek P/N: QKRC-10-05 Qualtek :NOISIVER PREPARED: R. J. N APPROVED: L. J. Y DATE: 2021-11-11