Q45AD9 BANNER | Alldatasheet

Document overview

  • Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
  • PDF pages: 10

Technical content

No revision without agency approval.

  • Designed for use with approved amplifiers and intrinsically safe barriers in explosive environments
  • NAMUR compliant sensor with the rugged design and exceptional optical performance of Q45 series sensors
  • Output passes ≤ 1.2 mA in the “dark” condition and ≥ 2.1 mA in the “light” condition
  • Internal multi-turn SENSITIVITY (Gain) control accessible beneath hinged, o-ring sealed top cover
  • Models are available with an integral cable or a quick-disconnect connector
  • Supply voltage: 5 to 15 V dc WARNING: Not To Be Used for Personnel Protection Never use this device as a sensing device for personnel protection. Doing so could lead to serious injury or death. This device does not include the self-checking redundant circuitry necessary to allow its use in personnel safety applications. A sensor failure or malfunction can cause either an energized or de-energized sensor output condition. Models Standard 2 m (6.5 ft) cable models are listed. To order the 9 m (30 ft) cable model, add suffix "W/30" to the cabled model number (Q459E W/30). Models with a QD connector require a mating cable (see Accessories list). Opposed Models - Emitter (E) and Receiver (R) Models Cable Performance Output Type Q459E 2 m (6.5 ft) 880 nm, infrared Range: 6meters (20 feet) Constant current ≤ 1.2 mA dark ≥ 2.1 mA light Q459EQ 4-Pin Euro QD Q45AD9R 2 m (6.5 ft) Q45AD9RQ 4-Pin Euro QD Retroreflective Models Retroreflective range is specified using one model BRT-3 P retroreflector (3-inch diameter). Actual sensing range may be more or less than specified, depending upon the efficiency and reflective area of the retroreflector(s) in use. Non-Polarized Models Cable Performance Output Type Q45AD9LV 2 m (6.5 ft) 680 nm, visible red Range: 9 m (30 ft) Constant Current ≤ 1.2 mA dark ≥ 2.1 mA lightQ45AD9LVQ 4-pin Euro QD Polarized Models Cable Performance Output Type Q45AD9LP 2 m (6.5 ft) 680 nm, visible red Range: 6 m (20 ft) Constant Current ≤ 1.2 mA dark ≥ 2.1 mA lightQ45AD9LPQ 4-pin Euro QD Diffuse Models Performance curves are based on a 90% reflectance white test card. Q45AD9 NAMUR Series Sensor Original Document 38343 Rev. K

3 April 2017

Short Range Models Cable Performance Output Type Q45AD9D 2 m (6.5 ft) 880 nm, infrared Range: 300 mm (12 in) Constant Current ≤ 1.2 mA dark ≥ 2.1 mA lightQ45AD9DQ 4-pin Euro QD Long Range Models Cable Performance Output Type Q45AD9DL 2 m (6.5 ft) 880 nm, infrared Range: 1 m (40 in) Constant Current ≤ 1.2 mA dark ≥ 2.1 mA lightQ45AD9DLQ 4-pin Euro QD Convergent Models Convergent mode models operate at 680 nm, visible red. Performance curves are based on a 90% reflectance white test card. Models Cable Focus Output Type Q45AD9CV 2 m (6.5 ft) 38 mm (1.5 in) Spot size at focus: 1.3 mm (0.05 in) Constant Current ≤ 1.2 mA dark ≥ 2.1 mA lightQ45AD9CVQ 4-pin Euro QD Q45AD9CV4 2 m (6.5 ft) 100 mm (4 in) Spot size at focus: 1.5 mm (0.06 in) Constant Current ≤ 1.2 mA dark ≥ 2.1 mA lightQ45AD9CV4Q 4-pin Euro QD Plastic Fiber Optic Models Performance curves are based on a 90% reflectance white test card. Models Cable Performance Output Type Q45AD9FP 2 m (6.5 ft) 660 nm, visible red Range: varies by sensing mode and fiber optics used Constant Current ≤ 1.2 mA dark ≥ 2.1 mA lightQ45AD9FPQ 4-pin Euro QD Glass Fiber Optic Models Performance curves are based on a 90% reflectance white test card. Models Cable Performance Output Type Q45AD9F 2 m (6.5 ft) 880 nm, infrared Range: varies by sensing mode and fiber optics used Constant Current ≤ 1.2 mA dark ≥ 2.1 mA lightQ45AD9FQ 4-pin Euro QD Models Cable Performance Output Type Q45AD9FV 2 m (6.5 ft) 650 nm, visible red Range: varies by sensing mode and fiber optics used Constant Current ≤ 1.2 mA dark ≥ 2.1 mA lightQ45AD9FVQ 4-pin Euro QD Overview The Q45AD9 Series NAMUR Sensor is a rugged, self-contained two-wire sensor designed for use with certified intrinsically safe switching amplifiers and barriers (Approved Apparatus) with intrinsically safe circuits. The Q45AD9 Series NAMUR sensor is designed in accordance with DIN 19234 (IEC/EN 60947-5-6) for operation via two-wire connection to an Approved Apparatus controlled by the variable internal resistance of the sensor. The sensor varies the impedance across the sensor output, which passes 1 mA or less in the "dark" condition and 2 mA or more in the "light" condition. A highly visible red LED indicator is located beneath a raised transparent dome on top of the sensor.

  • SIGNAL—LED lights red when the sensor sees its modulated light source
  • POWER (Emitters only)—LED lights red when 5 to 15 V dc power is applied Multi-turn sensitivity control on top of sensor, beneath a transparent cover, allows precise sensitivity setting (turn clockwise to increase gain). Q45AD9 NAMUR Series Sensor 2 www.bannerengineering.com - Tel: +1-763-544-3164 P/N 38343 Rev. K

Models are available with either a 2 m (6.5 ft) or 9 m (30 ft) long attached PVC-covered cable, or a 4-pin M12/Euro-style quick disconnect (QD) connector. Quick disconnect models (with Q in the model number suffix) use MQD9-4.. mating cable (either straight or right angle connector; see Accessories on page 9). Contact Banner Engineering for the availability of sensor models with 9 m (30 ft) long attached cable. Installation Instructions Ex/HazLoc Applications WARNING:

  • Explosive Atmospheres/Hazardous Locations
  • The user has the responsibility to ensure that all local, state, and national laws, rules, codes, or regulations relating to the installation and use of this Banner device in any particular application are satisfied. This Banner device must be installed by Qualified Persons, in accordance with this document and applicable regulations.
  • A Qualified Person is a person who, by possession of a recognized degree or certificate of professional training, or who, by extensive knowledge, training and experience, has successfully demonstrated the ability to solve problems relating to the subject matter and work. WARNING:
  • Explosion Hazard
  • Do not disconnect equipment unless the power has been switched off or the area is known to be non- hazardous. CAUTION: Electrostatic Discharge (ESD) Special Conditions for Safe Use. Parts of the enclosure are non-conducting and may generate an ignition-capable level of ESD. Cleaning of the equipment shall be done only with a damp cloth. General Notes and Conditions for Safe Use:
  • See Specifications and Wiring Diagrams for important information concerning entity parameters, permissible locations, electrical connections and certifications.
  • In addition to the warning above concerning user responsibility, the installation must comply with the following: ◦ All installations must comply with all manufacturer's instructions. ◦ U.S. Installations: The relevant requirements of the National Electrical Code® (ANSI/NFPA-70 (NEC®) and when appropriate ANSI/ISA-RP12.06.01 Installation of Intrinsically Safe Systems for Hazardous (Classified) Locations. ◦ Canadian Installations: The relevant requirements of the Canadian Electrical Code (CSA C22.1). ◦ ATEX and IECEx Installations: The relevant requirements of EN 60079-14 and applicable National regulations.
  • Do not attempt any repairs to this Banner device; it contains no field-replaceable parts or components. Tampering and/or replacement with non-factory components may adversely affect the safe use of the system.
  • Approved Apparatus entity parameters must meet the following requirements: ◦ V oc or Vt ≤ Vmax ◦ C a ≥ Ci + Ccable ◦ I sc or It ≤ Imax ◦ La ≥ Li + Lcable
  • Sensor Entity Parameters: ◦ V max (Ui) ≤ 15 V dc ◦ I max (li) ≤ 60 mA ◦ P i ≤ 225 mW ◦ C i = 0.3 μ F ◦ L i = 0 mH
  • Cable Entity Parameters (if unknown): ◦ C cable = 60 pF/ft ◦ L cable = 0.2 µH/ft
  • The ambient operating temperature range of the Sensors is − 40 °C to +70 °C (− 40 °F to +158 °F).
  • For U.S. installations, Class II and III, Division 2 applies only to model numbers ending in a Q suffix.
  • For intrinsically safe installations, sensors must be used with certified intrinsically safe switching amplifiers and barriers (Approved Apparatus) with intrinsically safe circuits that limit supply voltage and current in the event of failures.
  • Associated Apparatus is not required for installation of the devices within a Division 2 hazardous (classified) location when installed per the National Electrical Code. The maximum voltage for Division 2 installation is 15V dc. In Division 2 installations (without Associated Apparatus), observe Explosion Hazard warning at the beginning of this section.
  • Associated Apparatus is not required for installation of the devices within a Division 2 hazardous (classified) location when installed in, or through the wall of a suitable enclosure with provision for connection of rigid metal conduit per the Canadian Electrical Code, as acceptable to the local inspection authority having jurisdiction. The maximum rating for Division 2 installation is 15V dc, 60 mA. In Division 2 installations (without Associated Apparatus), observe Explosion Hazard warning at the beginning of this section.
  • Maximum non-hazardous area voltage that the Approved Apparatus (intrinsically safe circuit) is connected to must not exceed 250V. Q45AD9 NAMUR Series Sensor P/N 38343 Rev. K www.bannerengineering.com - Tel: +1-763-544-3164 3
  • Intrinsic safety ground, if required for the Associated Apparatus, shall be less than 1 ohm.
  • Maximum connector torque: 6 ft-lbs. Wiring Connections Q45AD9 Series NUMAR sensors are intrinsically safe ONLY when used with certified intrinsically safe switching amplifiers and barriers (Approved Apparatus) with intrinsically safe circuits. Banner does not manufacture such devices; however, our applications engineers can refer you to suppliers of certified devices that will interface with Banner sensors. The user is responsible for proper installation and maintenance of this equipment, and must conform with the certification requirements relating to barriers and to maximum allowable capacitance and inductance of the field wiring. If in doubt about these requirements, our applications engineers can refer you to the appropriate authority. NAMUR Sensors with Attached Cable NAMUR Sensors with Quick-Disconnect NAMUR Sensor Hazardous Area ≤ 15 V dcPower Output Sensor Input Non-hazardous Area Approved Apparatus br bu NAMUR Sensor Hazardous Area ≤ 15 V dcPower Output Sensor Input Non-hazardous Area Approved Apparatus br bu Specifications for Q45 NAMUR Sensors Supply Voltage and Current 5 to 15 V dc. Supply voltage is provided by the amplifier to which the sensor is connected. Adjustments Multi-turn sensitivity control on top of sensor, beneath a transparent o-ring sealed cover, allows precise sensitivity setting (turn clockwise to increase gain). Output Constant current output: ≤ 1.2 mA in the “dark” condition and ≥ 2.1 mA in the “light” condition Output Response Time Opposed mode receiver: 2 milliseconds on/0.4 milliseconds off. All others 5 milliseconds on/off (does not include amplifier response) Construction Molded thermoplastic polyester housing, o-ring sealed transparent Lexan® top cover, molded acrylic lenses, and stainless steel hardware. Q45s are designed to withstand 1200 psi washdown. The base of cabled models has a 1/2-inch NPS integral internal conduit thread. 1 Environmental Rating Banner tested to NEMA 6P, IEC IP67 Application Note Special Conditions for Safe Use: Parts of the enclosure are non-conducting and may generate an ignition-capable level of ESD. Cleaning of the equipment must be done only with a damp cloth. Indicators Indicator LEDs are highly visible, located beneath a raised transparent dome on top of the sensor. POWER (red) LED (emitters only) lights whenever 5 to 15 V dc power is applied SIGNAL (red) LED lights whenever the sensor sees its modulated light source Connections PVC-jacketed 2 m (6.5 ft) or 9 m (30 ft) cables, or 4-pin Euro-style quick- disconnect (QD) fitting are available. QD cables are ordered separately. See Accessories. Operating Conditions Temperature: − 40 °C to +70 °C ( − 40 °F to +158 °F) Maximum relative humidity: 90% at 50 °C (non-condensing) Certifications IEC IECEx FMG 14.0029X ATEX FM12ATEX0094X FM CoC 0003046293 (US) FM CoC 0003046293C (CAN) Design Standards ATEX (European) EN 60079-0, EN 60079-11 and EN 60079-26 United States FM Class 3600, 3610, and 3810; ANSI/ISA 61010-1 (82.02.01), 60079-0 and 60079-11 IECEx IEC 60079-0, IEC 60079-11 1 Lexan® is a registered trademark of General Electric Co. Q45AD9 NAMUR Series Sensor 4 www.bannerengineering.com - Tel: +1-763-544-3164 P/N 38343 Rev. K

Q45AD9(a)(b), Q459E(b) a = Sensing mode D, DL, F, FP, FV, LV, LP, CV, CV4 or R. b = Connection method Q or blank ATEX (European) II 1 G Ex ia IIC T5 Ta = -40°C to 70°C - 38343; Entity Entity Parameters: U i = 15 V dc, I i = 60 mA, P i = 225 mW, C i = 0.3 μ F, L i = 0 mH. Canadian IS / I,II,III / 1 / ABCDEFG / T5 Ta = -40°C to 70°C - 38343; Entity I / 0 / Ex ia / IIC / T5 Ta = -40°C to 70° C - 38343; Entity (Non-incendive) NI / I / 2 / ABCD / T5 Ta = -40°C to 70°C Entity Parameters: V Max = 15 V dc, I Max = 60 mA, P i = 225 mW, C i = 0.3 μ F, L i = 0 mH United States IS / I,II,III / 1 / ABCDEFG / T5 Ta = -40°C to 70°C - 38343; Entity I / 0 / AEx ia / IIC / T5 Ta = -40°C to 70°C - 38343; Entity (Non-incendive) NI / I / 2 / ABCD / T5 Ta = -40°C to 70°C S / II,III / 2 / FG* / T5 Ta = -40°C to 70°C *Class II and III, Division 2 applies only to model numbers ending in a Q suffix. Entity Parameters: V Max = 15 V dc, I Max = 60 mA, P i = 225 mW, C i = 0.3 μ F, L i = 0 mH IECEx Ex ia IIC T5 Ta= -40 °C to +70 °C - 35331; Entity Entity Parameters: U i = 15 V dc, I i = 60 mA, C i = 0.3 μ F, L i = 0 mH. 1 4 7 2 9 1 D Performance Curves Opposed Excess Gain Beam Pattern 100 1.0 m3.3 ft 10 m33 ft 100 m330 ft0.1 m0.33 ft EXCESS GAIN DISTANCE 1000 Q45AD9 E/ROpposed Mode 4.8 m16 ft6 m20 ft3.6 m12 ft2.4 m8 ft1.2 m4 ft0 050 mm100 mm150 mm 50 mm100 mm150 mm 02 in4 in6 in 2 in4 in6 in DISTANCE Q45AD9 E/ROpposed Mode Q45AD9 NAMUR Series Sensor P/N 38343 Rev. K www.bannerengineering.com - Tel: +1-763-544-3164 5

Retroreflective Non-Polarized Retroreflective Polarized Excess Gain Beam Pattern Excess Gain Beam Pattern 100 1000 EXCESSGAIN DISTANCE Q45AD9LV Retroreflective Mode With BRT-3 Reflector 12 m40 ft15 m50 ft9 m30 ft6 m20 ft3 m10 ft0 025 mm50 mm75 mm 25 mm50 mm75 mm 01.0 in2.0 in3.0 in 1.0 in2.0 in3.0 in DISTANCE Q45AD9LVRetroreflective Mode With BRT-3 Reflector 100 1000 EXCESSGAIN DISTANCE Q45AD9LP Retroreflective Mode With BRT-3 Reflector 6 m20 ft7.5 m25 ft4.5 m15 ft3 m10 ft1.5 m5 ft0 025 mm50 mm75 mm 25 mm50 mm75 mm 01.0 in2.0 in3.0 in 1.0 in2.0 in3.0 in DISTANCE Q45AD9LPRetroreflectiveMode With BRT-3 Reflector Diffuse Short Range Diffuse Long Range Excess Gain Beam Pattern Excess Gain Beam Pattern 100 10 mm0.4 in100 mm4.0 in1000 mm40 in1.0 mm0.04 in 1000 EXCESSGAIN DISTANCE Q45AD9D Diffuse Mode 05 mm10 mm15 mm 5 mm10 mm15 mm 00.2 in0.4 in0.6 in 0.2 in0.4 in0.6 in DISTANCE Q45AD9DDiffuse Mode 100 1000 EXCESSGAIN DISTANCE Q45AD9DL Diffuse Mode 02.5 mm5.0 mm7.5 mm 2.5 mm5.0 mm7.5 mm 00.1 in0.2 in0.3 in 0.1 in0.2 in0.3 in DISTANCE Q45AD9DLDiffuse Mode Convergent (CV and CVQ Models) Convergent (CV4 and CV4Q Models) Excess Gain Beam Pattern Excess Gain Beam Pattern 100 10 mm.4 in 100 mm4 in 1000 mm40 in1 mm.04 in 1000 EXCESSGAIN DISTANCE Q45AD9CV Convergent Mode 01.2 mm2.5 mm3.8 mm 1.2 mm2.5 mm3.8 mm 00.05 in0.10 in0.15 in 0.05 in0.10 in0.15 in DISTANCE Q45AD9CVConvergent Mode 100 10 mm.4 in 100 mm4 in 1000 mm40 in1 mm.04 in 1000 EXCESSGAIN DISTANCE Q45AD9CV4 Convergent Mode 01.2 mm2.5 mm3.8 mm 1.2 mm2.5 mm3.8 mm 00.05 in0.10 in0.15 in 0.05 in0.10 in0.15 in DISTANCE Q45AD9CV4Convergent Mode Q45AD9 NAMUR Series Sensor 6 www.bannerengineering.com - Tel: +1-763-544-3164 P/N 38343 Rev. K

Plastic Fiber Optic (Opposed Mode) Plastic Fiber Optic (Diffuse Mode) Excess Gain Beam Pattern Excess Gain Beam Pattern 100 10 mm0.4 in100 mm4.0 in1000 mm40 in1 mm0.04 in 1000 EXCESSGAIN DISTANCE Q45AD9FP Opposed Mode PIT46U Fibers PIT26U Fibers 015 mm30 mm45 mm 15 mm30 mm45 mm 00.6 in1.2 in1.8 in 0.6 in1.2 in1.8 in DISTANCE Q45AD9FPOpposed ModePIT46U Fibers PIT26U Fibers 100 1 mm0.04 in10 mm0.4 in100 mm4 in0.1 mm0.004 in 1000 EXCESSGAIN DISTANCE Q45AD9FP Diffuse Mode PBT46U Fiber PBT26U Fiber 00.8 mm1.6 mm2.4 mm 0.8 mm1.6 mm2.4 mm 00.03 in0.06 in0.09 in 0.03 in0.06 in0.09 in DISTANCE Q45AD9FPDiffuse Mode PBT46U Fiber Glass Fiber Optic, Infrared (Opposed Mode) Glass Fiber Optic, Infrared (Diffuse Mode) Excess Gain Beam Pattern Excess Gain Beam Pattern 100 10 mm0.4 in100 mm4 in 1000 mm40 in1.0 mm0.04 in 1000 EXCESSGAIN DISTANCE Q45AD9F Opposed Mode IT23S fibers IT13S fibers 625 mm25 in500 mm20 in375 mm15 in250 mm10 in125 mm5 in0 012.5 mm25.0 mm37.5 mm 12.5 mm25.0 mm37.5 mm 00.5 in1.0 in1.5 in 0.5 in1.0 in1.5 in DISTANCE Q45AD9FOpposed Mode IT23S Fibers IT13S Fibers 100 10 mm0.4 in100 mm4 in 1000 mm40 in1.0 mm0.04 in 1000 EXCESSGAIN DISTANCE Q45AD9F Diffuse Mode BT23S fiber BT13S fiber 00.5 mm1.0 mm1.5 mm 0.5 mm1.0 mm1.5 mm 00.02 in0.04 in0.06 in 0.02 in0.04 in0.06 in DISTANCE Q45AD9FDiffuse Mode BT23S Fiber BT13S Fiber Glass Fiber Optic, Visible Red (Opposed Mode) Glass Fiber Optic, Visible Red (Diffuse Mode) Excess Gain Beam Pattern Excess Gain Beam Pattern 100 10 mm0.4 in100 mm4 in 1000 mm40 in1.0 mm0.04 in 1000 EXCESSGAIN DISTANCE Q45AD9FV Opposed Mode IT23S Fibers IT13S Fibers 300 mm12 in250 mm10 in200 mm8 in150 mm6 in100 mm4 in0 010 mm20 mm30 mm 10 mm20 mm30 mm 00.4 in0.8 in1.2 in 0.4 in0.8 in1.2 in DISTANCE Q45AD9FVOpposed ModeIT23S Fibers IT13S Fibers 100 10 mm0.4 in100 mm4.0 in1000 mm40 in1 mm0.04 in 1000 EXCESSGAIN DISTANCE Q45AD9FV Diffuse Mode BT23S FiberBT13SFiber 01.0 mm2.0 mm3.0 mm 1.0 mm2.0 mm3.0 mm 00.04 in0.08 in0.12 in 0.04 in0.08 in0.12 in DISTANCE Q45AD9FVDiffuse Mode BT23S Fiber BT13S Fiber Q45AD9 NAMUR Series Sensor P/N 38343 Rev. K www.bannerengineering.com - Tel: +1-763-544-3164 7

NAMUR Series Opposed, Retro, and Diffuse Sensing Modes (Model Suffix E, R, D, DL, LP, and LV) Cabled Models Quick-Disconnect 4-pin Euro-style Models 54.1 mm(2.13") 44.5 mm(1.75") 69.0 mm(2.72") 87.6 mm(3.45") Internal Thread(1/2–14NPSM) 30.0 mm(1.18") ø 6.1 (0.24")2m (6.5') Cable 7.1 mm(0.28") 4.5 mm (#10) ScrewClearance (2) 50.8 mm(2.00") 6.4 mm (0.25") Lens Centerline External thread (M30 x 1.5)hex nut supplied 15 mm (0.6") Euro- or Micro-styleQD Connector Convergent Sensor Models (CV and CV4) Glass Fiber Optic Models (F and FV) Plastic Fiber Optic Models (FP) 61.7 mm(2.43") Q45AD9 NAMUR Series Sensor 8 www.bannerengineering.com - Tel: +1-763-544-3164 P/N 38343 Rev. K

Quick-Disconnect (QD) Cables 4-Pin Threaded M12/Euro-Style Cordsets (for use with NAMUR sensors) Model Length Style Dimensions Pinout (Female) MQD9-406 1.83 m (6 ft) Straight 44 Typ. ø 14.5 M12 x 1 1 = Brown 2 = Blue MQD9-415 4.57 m (15 ft) MQD9-430 9.14 m (30 ft) MQD9-406RA 1.83 m (6 ft) Right-Angle 32 Typ.[1.26"] 30 Typ.[1.18"] ø 14.5 [0.57"] M12 x 1 MQD9-415RA 4.57 m (15 ft) MQD9-430RA 9.14 m (30 ft) Replacement Lenses Replacement Lens Assemblies Models Description UC-45L Replacement lens for E, R, DL and LV models UC-45LP Replacement lens for LP UC-45D Replacement lens for D UC-45F Replacement lens for F and FV UC-45FP Replacement lens for FP UC-45C Replacement lens for CV UC-45C4 Replacement lens for CV4 Q45 Series lens assemblies are field-replaceable. Brackets Mounting Brackets SMB30C

  • 30 mm split clamp, black PBT bracket
  • Stainless steel mounting hardware included
  • Mounting hole for 30 mm sensor A B Hole center spacing: A=ø 45 Hole size: B=ø 27.2 SMB30SC
  • Swivel bracket with 30 mm mounting hole for sensor
  • Black reinforced thermoplastic polyester
  • Stainless steel mounting and swivel locking hardware included B A Hole center spacing: A=ø 50.8 Hole size: A=ø 7.0, B=ø 30.0 Q45AD9 NAMUR Series Sensor P/N 38343 Rev. K www.bannerengineering.com - Tel: +1-763-544-3164 9
  • 12-ga. stainless steel bracket with curved mounting slots for versatile orientation
  • Clearance for M6 (¼ in) hardware
  • Mounting hole for 30 mm sensor A B C Hole center spacing: A = 51, A to B = 25.4 Hole size: A = 42.6 x 7, B = ø 6.4, C = ø 30.1 SMB30UR
  • 2-piece universal swivel bracket for limit-switch style sensors
  • 300 series stainless steel
  • Stainless steel swivel locking hardware included Hole center spacing: A to B=31.8, B to C=19.0, A to C=50.8, D=50.8 Hole size: C=6.9x32, D=73.0x6.9 Repairs and Translations Obtain assistance with product repairs by contacting your local Banner Engineering Corp distributor or by calling Banner directly at (763) 544-3164. Access literature translated into your native language on the Banner website at www.bannerengineering.com or contact Banner directly at (763) 544-3164. Para reparaciones de productos, por favor contacte a su distribuidor local de Banner Engineering o llame a Banner directamente al (763) 544-3164. Vea la literatura traducida en su idioma en el sitio web Banner en www.bannerengineering.com o comuníquese con Banner directamente al (763) 544-3164. Pour vous aider lors de la réparation de produits, contactez votre distributeur Banner local our appelez directement Banner au (763) 544-3164. La documentation traduite dans votre langue est disponible sur le site internet de Banner www.bannerengineering.com ou contactez directement Banner au (763) 544-3164. Banner Engineering Corp. Limited Warranty Banner Engineering Corp. warrants its products to be free from defects in material and workmanship for one year following the date of shipment. Banner Engineering Corp. will repair or replace, free of charge, any product of its manufacture which, at the time it is returned to the factory, is found to have been defective during the warranty period. This warranty does not cover damage or liability for misuse, abuse, or the improper application or installation of the Banner product. THIS LIMITED WARRANTY IS EXCLUSIVE AND IN LIEU OF ALL OTHER WARRANTIES WHETHER EXPRESS OR IMPLIED (INCLUDING, WITHOUT LIMITATION, ANY WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE), AND WHETHER ARISING UNDER COURSE OF PERFORMANCE, COURSE OF DEALING OR TRADE USAGE. This Warranty is exclusive and limited to repair or, at the discretion of Banner Engineering Corp., replacement. IN NO EVENT SHALL BANNER ENGINEERING CORP. BE LIABLE TO BUYER OR ANY OTHER PERSON OR ENTITY FOR ANY EXTRA COSTS, EXPENSES, LOSSES, LOSS OF PROFITS, OR ANY INCIDENTAL, CONSEQUENTIAL OR SPECIAL DAMAGES RESULTING FROM ANY PRODUCT DEFECT OR FROM THE USE OR INABILITY TO USE THE PRODUCT, WHETHER ARISING IN CONTRACT OR WARRANTY, STATUTE, TORT, STRICT LIABILITY, NEGLIGENCE, OR OTHERWISE. Banner Engineering Corp. reserves the right to change, modify or improve the design of the product without assuming any obligations or liabilities relating to any product previously manufactured by Banner Engineering Corp. Any misuse, abuse, or improper application or installation of this product or use of the product for personal protection applications when the product is identified as not intended for such purposes will void the product warranty. Any modifications to this product without prior express approval by Banner Engineering Corp will void the product warranties. All specifications published in this document are subject to change; Banner reserves the right to modify product specifications or update documentation at any time. Specifications and product information in English supersede that which is provided in any other language. For the most recent version of any documentation, refer to: www.bannerengineering.com. Q45AD9 NAMUR Series Sensor © Banner Engineering Corp. All rights reserved