2MS1T2B2M2RE MULTICOMP | Alldatasheet
Document overview
- Manufacturer or author: Provided By alldatasheet.com(free datasheet download site)
- PDF pages: 4
Technical content
Page <1> V1.005/05/20 Toggle Switches Sub-Miniature Newark.com/multicomp-pro Farnell.com/multicomp-pro Element14.com/multicomp-pro Specifications Contact Rating : Dependent upon content material Mechanical Life : 30,000 make and break cycles Maximum Contact Resistance : 20mΩ initial at 2-4 V DC 100mA for both silver and gold plated contacts Minimum insulation Resistance : 1,000MΩ. Dielectric strength : 1,000V rms at sea level Operating Temperature : -30°C to +85°C Materials: Case : Diallyl phthalate (DAP). Actuator : Brass, chrome plated. Bushing : Brass, nickel plated. Housing : Stainless steel. Switch Support : Brass, tin plated. Terminal / Contact : Silver or gold plated. Switch Function Number of Poles UL / CSA Model Number Model Number Switch Function Connected Terminals / Schematic Position 1 Position 2 Position 3 Position 1 Position 2 Position 3 SP Q2211 2MS1 On None ON N/A Q2212 2MS2 MOM Q2213 2MS3 Off ON Open DP Q2221 2MD1 On None N/A Q2223 2MD3 Off Open MOM = Momentary Pole Options SPDT 2MS6 Models : Omit 2nd terminal Dimensions : Inches (Millimetres)
Page <2> V1.005/05/20 Toggle Switches Sub-Miniature Newark.com/multicomp-pro Farnell.com/multicomp-pro Element14.com/multicomp-pro DPDT Actuator Options T1, T2, Actuator shown with B2 bushing, subtract 0.09 (2.29) for B5 bushing, subtract 0.04 (1.02) for B5 bushing, Bushing Options Termination Options M6, SPDT Dimensions : Inches (Millimetres)
Page <3> V1.005/05/20 Toggle Switches Sub-Miniature Newark.com/multicomp-pro Farnell.com/multicomp-pro Element14.com/multicomp-pro M6, DPDT Panel Mounting Hardware Contact Material Options Dimensions : Inches (Millimetres) Contact Plating Terminal Plating Ratings R Gold R = Gold 0.4 Volt - Amperes (VA) maximum at 20V maximum (AC or DC) Soldering Process Manual Soldering : Use soldering iron of 30 watts, controlled at 350°C approximately 5 s while applying solder. Wave Soldering : Recommended soldering temperature : 260 ±5°C. : Duration of solder immersion : Maximum 5 s (PCB is 1.6 mm in thickness). Soldering : Vapour phase
Page <4> V1.005/05/20 Toggle Switches Sub-Miniature Newark.com/multicomp-pro Farnell.com/multicomp-pro Element14.com/multicomp-pro Important Notice : This data sheet and its contents (the “Information”) belong to the members of the AVNET group of companies (the “Group”) or are licensed to it. No licence is granted for the use of it other than for information purposes in connection with the products to which it relates. No licence of any intellectual property rights is granted. The Information is subject to change without notice and replaces all data sheets previously supplied. The Information supplied is believed to be accurate but the Group assumes no responsibility for its accuracy or completeness, any error in or omission from it or for any use made of it. Users of this data sheet should check for themselves the Information and the suitability of the products for their purpose and not make any assumptions based on information included or omitted. Liability for loss or damage resulting from any reliance on the Information or use of it (including liability resulting from negligence or where the Group was aware of the possibility of such loss or damage arising) is excluded. This will not operate to limit or restrict the Group’s liability for death or personal injury resulting from its negligence. Multicomp Pro is the registered trademark of Premier Farnell Limited 2019. Part Number Explanation