PWM-60

PWM-60_V01 MEANWELL | Alldatasheet

Document overview

• Manufacturer or author: Provided By alldatasheet.com(free datasheet download site)
• PDF pages: 8

Technical content

File Name:PWM-60-SPEC 2019-01-10 60W PWM Output LED Driver PW M -60 seri es IS 15885(Part 2/Sec13) R-41027766 THOMAS SAMUEL THOMAS SAMUEL 

60W PWM Output LED Driver PW M -60 seri es MODEL DC VOLTAGE RATED CURRENT RATED POWER OUTPUT SETUP, RISE TIME Note.2 HOLD UP TIME (Typ.) VOLTAGE RANGE Note.3 FREQUENCY RANGE POWER FACTOR (Typ.) EFFICIENCY (Typ.) AC CURRENT (Typ.) INPUT INRUSH CURRENT (Typ.) LEAKAGE CURRENT SAFETY STANDARDS Note.5 WORKING TEMP. WORKING HUMIDITY STORAGE TEMP., HUMIDITY TEMP. COEFFICIENT VIBRATION MTBF DIMENSIONOTHERS NOTE PACKING OVERLOAD OVER VOLTAGE OVER TEMPERATURE 0 ~ 100% 1.47kHz 500ms, 80ms/ 115AC or 230VAC 16ms/115VAC or 230VAC 90 ~ 305VAC 127 ~ 431VDC 47 ~ 63Hz PF>0.97/115VAC, PF>0.95/230VAC, PF>0.92/277VAC @ full load (Please refer to "POWER FACTOR (PF) CHARACTERISTIC" section) <0.25mA / 277VAC 108 ~ 125% rated output power Hiccup mode, recovers automatically after fault condition is removed 20 ~ 95% RH non-condensing 10 ~ 500Hz, 5G 12min./1cycle, period for 72min. each along X, Y, Z axes 996K hrs min. Telcordia SR-332 (Bellcore) ; 271.03K hrs min. MIL-HDBK-217F (25℃) DIMMING RANGE PWM FREQUENCY (Typ.) ENVIRONMENT SAFETY & EMC PROTECTION Shut down o/p voltage, re-power on to recover 15 ~ 17V 28 ~ 34V 41 ~ 46V 54 ~ 60V PWM-60-12 PWM-60-24 PWM-60-36 PWM-60-48 WITHSTAND VOLTAGE ISOLATION RESISTANCE I/P-O/P:3.75KVAC I/P-O/P:100M Ohms / 500VDC / 25℃/ 70% RH EMC IMMUNITY Compliance to EN55015, EN61000-3-2 Class C (@load≧60%) ; EN61000-3-3,GB17743 and GB17625.1,EAC TP TC 020 Compliance to EN61000-4-2,3,4,5,6,8,11; EN61547, light industry level (surge immunity Line-Line 2KV),EAC TP TC 020 EMC EMISSION Note.6 COLD START 50A(twidth=270 s measured at 50% Ipeak) at 230VAC ; Per NEMA 410 μ TOTAL HARMONIC DISTORTION MAX. NO. of PSUs on 16A CIRCUIT BREAKER 9 units (circuit breaker of type B) / 16 units (circuit breaker of type C) at 230VAC SHORT CIRCUIT (Please refer to "STATIC CHARACTERISTIC" section) THD< 20%(@load≧60%/115VAC, 230VAC; @load≧75%/277VAC) (Please refer to “TOTAL HARMONIC DISTORTION” section) Tcase=-40 ~ + (Please refer to “ OUTPUT LOAD vs TEMPERATURE” section)85℃ Tcase=+85℃MAX. CASE TEMP. UL8750( type ”HL” )( except for DA-Type), UL879( for 12V,24V Blank Type only), CSA C22.2 No. 250.13-12; ENEC EN61347-1, EN61347-2-13 independent,EN62384, IP67,BIS IS15885(for 12,24,48 Blank Type only), EAC TP TC 004, GB19510.1, GB19510.14 approved; Design refer to EN60335-1 86% 89% 90% 90% ±0.03%/℃ (0 ~ 50℃) 0.49Kg;30pcs/15.7Kg/1.0CUFT 150*53*35mm (L*W*H) Shut down o/p voltage, re-power on to recover 12V 24V 36V 48V 5A 2.5A 1.67A 1.25A 60W 60W 60.12W 60W 0.8A / 115VAC 0.4A / 230VAC 0.32A / 277VAC Shut down o/p voltage, re-power on to recover File Name:PWM-60-SPEC 2019-01-10 DALI STANDARDS Comply with IEC62386-101, 102, 207 for DA-Type only,Device type 6(DT6)

◎ Applying additive 0 ~ 10VDC ◎ Applying additive 10V PWM signal (frequency range 100Hz ~ 3KHz): LED Strips LED Strips Vo+ Vo- DIM+ DIM- + + - - “DO NOT connect "DIM- to Vo-" Additive Voltage DIM+ DIM- “DO NOT connect "DIM- to Vo-" Additive PWM signal 0V 1V 2V 3V 4V 5V 6V 7V 8V 9V 10V 20% 30% 40% 50% 60% 70% 80% 90% 100% 10% 20% 30% 40% 50% 60% 70% 80% 90% 100% Dimming input: Additive voltage Duty cycle of additive 10V PWM signal dimming input ※ Dimming principle for PWM style output ‧Apply one of the three methodologies between DIM+ and DIM-: 0 ~ 10VDC, or 10V PWM signal or resistance. ‧Dimming source current from power supply: 100 A (typ.)μ ON OFF TON T Output DC current Io=0A Output PWM frequency : 1.47kHz fixed (Typ.) Duty cycle(%) = ×100% TON T ‧Dimming is achieved by varying the duty cycle of the output current. ※ 3 in 1 dimming function (for Blank-Type) 60W PWM Output LED Driver PW M -60 seri es 10% Duty cycle of output current (%)Duty cycle of output current (%) UL2464 18AWG×2C(Vo+,Vo-) UL2464 22AWG×2C(DIM+,DIM-) Vo+(Red) DIM+(Blue)* Vo-(Black) DIM-(White)* * SJTW 18AWG×2C AC/L(Brown) AC/N(Blue) Vo+ Vo- 0.6V 1V 0.15% 10% 6% 10% 0.15% 10% File Name:PWM-60-SPEC 2019-01-10 * DIM+ for Blank-Type DA+ for DA-type * *DIM- for Blank-Type DA- for DA-type NOTE: DA Type is no distinction between “+” and “-” poles

◎ Applying additive resistance: Vo+ Vo- DIM+ DIM- “DO NOT connect "DIM- to Vo-" Additive Resistance 10% 20% 30% 40% 50% 60% 70% 80% 90% 100% Short 10K/N 20K/N 30K/N 40K/N 50K/N 60K/N 70K/N 80K/N 90K/N 100K/N 60W PWM Output LED Driver PW M -60 seri es LED Strips (N=driver quantity forsynchronizeddimmingoperation) Dimming input: Additive resistance Note : 1. Min. duty cycle of output current is about 6% and the output current is not defined when 0%< Iout<6%. 2. The duty cycle of output current could drop down to 0% when dimming input is about 0kΩ or 0Vdc, or 10V PWM signal with 0% duty cycle. Duty cycle of output current (%) 6K/N 10K/N 10% File Name:PWM-60-SPEC 2019-01-10 ‧Apply DALI signal between DA+ and DA-. ‧DALI protocol comprises 16 groups and 64 addresses. ‧First step is fixed at 0.2% of output ※ DALI Interface (primary side; for DA-Type)

0.3 0.4 0.5 0.6 0.7 0.8 0.9 1.0 10% 20% 30% 40% 50% 60% 70% 80% 90% 100% 277V 230V 115V 90 100 125 135 145 155 165 175 180 200 230 305 100 175 60W PWM Output LED Driver PWM-60 series PF LOAD OUTPUT LOAD vs TEMPERATURE STATIC CHARACTERISTIC TOTAL HARMONIC DISTORTION (THD) AMBIENT TEMPERATURE,Ta ( )℃ LOAD (%) INPUT VOLTAGE (V) 60Hz LOAD (%) (HORIZONTAL) POWER FACTOR (PF) CHARACTERISTIC Tcase ( )℃ LOAD (%) (HORIZONTAL) ※De-rating is needed under low input voltage. EFFICIENCY vs LOAD PWM-60 series possess superior working efficiency that up to 90% can be reached in field applications. - 4 0 - 2 5 0 2 04 56 07 08 08 5 100 ※ 48V Model, Tcase at 75 ℃ ※ 48V Model, Tcase at 75 ℃ EFFICIENCY(%) LOAD THD LOAD ※ Tcase at 75 ℃ 230VAC Input only -40 -25 -10 0 15 30 50 60 70 100 230VAC Input only (60W) 10% 12% 14% 16% 18% 20% 50% 60% 70% 80% 90% 100% 277VAC 230VAC 115VAC 78% 80% 82% 84% 86% 88% 90% 92% 10% 20% 30% 40% 50% 60% 70% 80% 90% 100% 277V 230V 115V File Name:PWM-60-SPEC 2019-01-10

Tc/c97/c115/c101/c40/c32/c32/c32/c32/c32/c32/c41℃ LIFETIME (Kh) 60W PWM Output LED Driver PWM-60 series 100 120 25 35 45 55 65 75 85 File Name:PWM-60-SPEC 2019-01-10

60W PWM Output LED Driver PW M -60 seri es Mechanical Specification Case No. NPF-60A Unit:mm Block Diagram PFC fosc : 50~120KHz PWM fosc : 60~130KHz tc ‧ : Max. Case Temperaturetc DETECTION DIMMING PWM & PFC CIRCUIT CIRCUIT EMI FILTER RECTIFIERS POWER SWITCHING FILTER RECTIFIERS Vo+ Vo-I/P CONTROL O.V.P. O.L.P. PFC CIRCUIT DIM+ DIM- UL2464 18AWG×2C(Vo+,Vo-) UL2464 22AWG×2C(DIM+,DIM-) Vo+(Red) DIM+(Blue)* Vo-(Black) DIM-(White)** SJTW 18AWG×2C AC/L(Brown) AC/N(Blue) 150 ψ4.5 35 300±20 300±20 File Name:PWM-60-SPEC 2019-01-10 * DIM+ for Blank-Type DA+ for DA-type * *DIM- for Blank-Type DA- for DA-type NOTE: DA Type is no distinction between “+” and “-” poles Recommend Mounting Direction

60W PWM Output LED Driver PW M -60 seri es Installation Manual ◎Connection for Blank-type ◎Cautions Before commencing any installation or maintenance work, please disconnect the power supply from the utility. Ensure‧ that it cannot be re-connected inadvertently! Keep proper ventilation around the unit and do not stack any object on it. Also a 10-15 cm clearance must be kept when ‧ the adjacent device is a heat source. Mounting orientations other than standard orientation or operate under high ambient temperature may increase the ‧ internal component temperature and will require a de-rating in output current. Current rating of an approved primary /secondary cable should be greater than or equal to that of the unit. Please refer ‧ to its specification. For LED drivers with waterproof connectors, verify that the linkage between the unit and the lighting fixture is ‧ tight so that water cannot intrude into the system. For dimmable LED drivers, make sure that your dimming controller is capable of driving these units.PWM series ‧ require 0.15mA each unit. Tc max. is identified on the product label. Please make sure that temperature of Tc point will not exceed limit.‧ DO NOT connect "DIM- to Vo-".‧ ‧Suitable for indoor use or outdoor use without direct sunlight exposure. Please avoid immerse in the water over 30 minutes. ‧The power supply is considered as a component that will be operated in combination with final equipment. Since EMC performance will be affected by the complete installation, the final equipment manufacturers must re-qualify EMC Directive on the complete installation again. ‧For more information about installation, http://www.meanwell.com/manual.html for details.Please refer to : AC/L(BROWN) Vo+(RED) Vo-(BLACK) DIM-(WHITE) DIM+(BLUE) AC/N(BLUE) LED Strip - 0~10Vdc or 10V PWM or resistance Dimmer or DALI Dimmer File Name:PWM-60-SPEC 2019-01-10