DATASHEET SEARCH SITE | WWW.ALLDATASHEET.COM

Document overview

  • Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
  • PDF pages: 8

Technical content

200W Constant Voltage PWM Output LED Driver PW M -200 seri es File Name:PWM-200-SPEC 2021-09-17 IP67 User’s Manual

200W PWM Output LED Driver PW M -200 seri es MODEL DC VOLTAGE RATED CURRENT RATED POWER OUTPUT SETUP, RISE TIME HOLD UP TIME (Typ.) VOLTAGE RANGE Note.3 FREQUENCY RANGE POWER FACTOR (Typ.) EFFICIENCY (Typ.) AC CURRENT (Typ.) INPUT INRUSH CURRENT (Typ.) LEAKAGE CURRENT SAFETY STANDARDS Note.5 WORKING TEMP. WORKING HUMIDITY STORAGE TEMP., HUMIDITY TEMP. COEFFICIENT VIBRATION MTBF DIMENSIONOTHERS NOTE PACKING OVERLOAD OVER VOLTAGE OVER TEMPERATURE 4kHz for Blank type; 2.5kHz for DA2 type 500ms, 80ms/230VAC or 115VAC 10ms/230VAC or 115VAC 100 ~ 305VAC 142 ~ 431VDC 47 ~ 63Hz PF>0.97/115VAC, PF>0.96/230VAC, PF>0.94/277VAC @ full load (Please refer to "POWER FACTOR (PF) CHARACTERISTIC" section) 92% 93% 94% 94% <0.75mA / 277VAC 108 ~ 135% rated output power Hiccup mode or Constant current limiting,recovers automatically after fault condition is removed 20 ~ 95% RH non-condensing ±0.03%/℃ (0 ~ 50℃) 10 ~ 500Hz, 5G 12min./1cycle, period for 72min. each along X, Y, Z axes 712.8 K hrs min. Telcordia SR-332 (Bellcore) ; 178.7 K hrs min. MIL-HDBK-217F (25℃) Shut down o/p voltage, re-power on to recover after fault condition is removed DIMMING RANGE PWM FREQUENCY (Typ.) ENVIRONMENT SAFETY & EMC PROTECTION Shut down o/p voltage, re-power on to recover after fault condition is removed 13 ~ 18V 27 ~ 34V 41 ~ 49V 53 ~ 65V 2.2A / 115VAC 1.1A / 230VAC 0.9A / 277VAC WITHSTAND VOLTAGE ISOLATION RESISTANCE I/P-O/P: 100M Ohms / 500VDC / 25℃ / 70% RH EMC IMMUNITY Compliance to BS EN/EN55015, BS EN/EN61000-3-2 Class C (@load≧60%) ; BS EN/EN61000-3-3,GB17743 and GB17625.1,EAC TP TC 020 Compliance to BS EN/EN61000-4-2,3,4,5,6,8,11; BS EN/EN61547, light industry level (surge immunity, Line-Line 2KV),EAC TP TC 020 EMC EMISSION Note.6 COLD START 65A(twidth=550 s measured at 50% Ipeak) at 230VAC ; Per NEMA 410 μ TOTAL HARMONIC DISTORTION 1.03Kg; 12pcs/ 13.4Kg/ 0.71CUFT MAX. NO. of PSUs on 16A CIRCUIT BREAKER 3 units (circuit breaker of type B) / 5 units (circuit breaker of type C) at 230VAC SHORT CIRCUIT (Please refer to "STATIC CHARACTERISTIC" section) THD<20%(@load≧60%/115VAC, 230VAC; @load≧75%/277VAC) (Please refer to “TOTAL HARMONIC DISTORTION” section) standby power consumption<0.5W when dimming off Tcase=-40 ~ +85 (Please refer to “ OUTPUT LOAD vs TEMPERATURE” section)℃ Tcase=+85℃MAX. CASE TEMP. UL8750( type ”HL” ), CSA C22.2 No. 250.13-12; ENEC BS EN/EN61347-1, BS EN/EN61347-2-13,BS EN/EN62384 independent, IP67, EAC TP TC 004,GB19510.1,GB19510.14 approved; Design refer to BS EN/EN60335-1, According to BS EN/EN61347-2-13 appendix J suitable for emergency installations Shut down o/p voltage, re-power on to recover (except for DA2-type) 12V 15A 180W 0 ~ 100% PWM-200-12 24V 8.3A 199.2W PWM-200-24 36V 5.55A 199.8W PWM-200-36 48V 4.17A 200.1W PWM-200-48 DALI STANDARDS Comply with IEC62386-101, 102, 207, 251 for DA2 Type only, Device type 6(DT6) STANDBY POWER CONSUMPTION File Name:PWM-200-SPEC 2021-09-17 I/P-O/P: 3.75KVAC; I/P-DA: 1.5KVAC; O/P-DA:1.5KVAC Hiccup mode,recovers automatically after fault condition is removed (only for DA2-type) Note.10 Note.2

◎ Applying additive 0 ~ 10VDC ◎ Applying additive 10V PWM signal (frequency range 100Hz ~ 3KHz): LED Strips LED Strips DIM+ DIM- + + - - “DO NOT connect "DIM- to -V" Additive Voltage DIM+ DIM- “DO NOT connect "DIM- to -V" Additive PWM signal 0V 1V0.6V 10% 2V 3V 4V 5V 6V 7V 8V 9V 10V 20% 30% 40% 50% 60% 70% 80% 90% 100% 10% 20% 30% 40% 50% 60% 70% 80% 90% 100% Dimming input: Additive voltage Duty cycle of additive 10V PWM signal dimming input ※ Dimming principle for PWM style output ‧Apply one of the three methodologies between DIM+ and DIM-: 0 ~ 10VDC, or 10V PWM signal or resistance. ‧Dimming source current from power supply: 100 A (typ.)μ ON OFF TON T Output DC current Io=0A Output PWM frequency : 4KHz fixed (Blank type) 2.5KHz fixed (DA2 type) Duty cycle(%) = ×100% TON T ‧Dimming is achieved by varying the duty cycle of the output current. ※ 3 in 1 dimming function (for Blank-Type) 200W PWM Output LED Driver PW M -200 seri es 10%1% 10% 10% Duty cycle of output current (%)Duty cycle of output current (%) File Name:PWM-200-SPEC 2021-09-17 AC/N(Blue) AC/L(Brown) Vo+(Red) Vo-(Black) PWM-200 DIM+/DA+(Blue)* DIM-/DA-(White)** * DIM+ for Blank-Type DA+ for DA2-type * *DIM- for Blank-Type DA- for DA2-type

◎Applying additive resistance: Note : 1. Min. duty cycle of output current is about 1%, and the dimming input is about 6KΩ or 0.6VDC, or 10V PWM signal with 6% duty cycle. 2. The duty cycle of output current could drop down to 0% when dimming input is less than 6KΩ or less than 0.6VDC, or 10V PWM signal with duty cycle less than 6%. DIM+ DIM- “DO NOT connect "DIM- to -V" Additive Resistance 10% 20% 30% 40% 50% 60% 70% 80% 90% 100% Short 10K/N 20K/N 30K/N 40K/N 50K/N 60K/N 70K/N 80K/N 90K/N 100K/N 200W PWM Output LED Driver PW M -200 seri es ‧Apply DALI signal between DA+ and DA-. ‧DALI protocol comprises 16 groups and 64 addresses. ‧Min.duty cycle of output current is about 0.2% ◎ DALI Interface (for DA2-Type) LED Strips 6K/N 10K/N 10% (N=driver quantity forsynchronizeddimmingoperation) Dimming input: Additive resistance Duty cycle of output current (%) File Name:PWM-200-SPEC 2021-09-17 ◎ PUSH dimming(primary side) ‧The factory default dimming level is at 100%. ‧If the push action lasts less than 0.05 sec., it will not lead to a change for the status of the driver. ‧Up to 10 drivers can perform the PUSH dimming at the same time when utilizing one common push button. Action FunctionAction duration Short push 0.1~1 sec. Turn ON-OFF the driver Long push 1.5~10 sec. Every Long Push changes the dimming direction, dimming up or down Reset >11 sec. Set up the dimming level to 100% ‧The maximum length of the cable from the push button to the last driver is 20 meters. ‧The additive push button can be connected only between the DA+ terminal, as displayed in the diagram, and AC/L (in brown or black); it will lead to short circuit if it is connected to AC/N. ※DALI interface DC OUT DA- DA+ Push Button AC/L AC/N

100 110 125 135 150 180 200 240 260 280 305 100 220 230VAC Input only 100 -25 0 15 3004 0 5 0-40 60 70 110VAC 200W PWM Output LED Driver PWM-200 series PF LOAD OUTPUT LOAD vs TEMPERATURE STATIC CHARACTERISTIC TOTAL HARMONIC DISTORTION (THD) AMBIENT TEMPERATURE,Ta ( )℃ LOAD (%) INPUT VOLTAGE (V) 60Hz LOAD (%) (HORIZONTAL) POWER FACTOR (PF) CHARACTERISTIC Tcase ( )℃ LOAD (%) (HORIZONTAL) EFFICIENCY vs LOAD PWM-200 series possess superior working efficiency that up to 94% can be reached in field applications. - 4 0 - 2 5 0 2 04 55 56 57 58 5 100 ※ 48V Model, Tcase at 75 ℃ ※ 48V Model, Tcase at 75 ℃ EFFICIENCY(%) THD LOADLOAD ※ Tcase at 75 ℃ 230VAC Input only File Name:PWM-200-SPEC 2021-09-17 230VAC 0.2 0.25 0.3 0.35 0.4 0.45 0.5 0.55 0.6 0.65 0.7 0.75 0.8 0.85 0.9 0.95 10% 20% 30% 40% 50% 60% 70% 80% 90% 100% 230VAC 115VAC 277VAC 10% 11% 12% 13% 14% 15% 16% 17% 18% 19% 20% 50% 60% 70% 80% 90% 100% 230VAC 115VAC 277VAC 10% 20% 30% 40% 50% 60% 70% 80% 90% 100% 230VAC 115VAC 277VAC

25 30 35 40 45 50 55 60 65 70 75 80 85 LIFE TIME Tc a s e )( ℃ LIFETIME (Kh) 200W PWM Output LED Driver PWM-200 series File Name:PWM-200-SPEC 2021-09-17

200W PWM Output LED Driver PW M -200 seri es Mechanical Specification Case No. PWM-200 Unit:mm Block Diagram DETECTION DIMMING PWM & PFC CIRCUIT CIRCUIT EMI FILTER RECTIFIERS POWER SWITCHING FILTER RECTIFIERS +V -VI/P CONTROL O.V.P. O.L.P. PFC CIRCUIT PFC fosc : 50~120KHz PWM fosc : 60~130KHz DIM+/DA+ DIM-/DA- File Name:PWM-200-SPEC 2021-09-17 195300 300 20± 50±3 SJOW 17AWG*2C for DA2-Type Ul2464 20AWG*2C for Blank-Type Vo+(Red) Vo-(Black) DIM-/DA-(White) DIM+/DA+(Blue) AC/N(Blue) AC/L(Brown) SJOW 17AWGX2C&H05RN-F 2X1.0mm² SJOW 14AWG*2C for 12V SJOW 17AWG*2C & 05RN-F2*1.0mm², for 24V/36V/48V 39.5 ‧ : Max. Case Temperature for Input 110Vactc1 2-ψ4.5 50±3 350 20± 97.5tc2 tc160 ‧ : Max. Case Temperature for Input 230Vactc2

200W PWM Output LED Driver PW M -200 seri es Installation Manual AC/L(BROWN) AC/N(BLUE) ◎Connection for Blank-type and DA2-type ◎Cautions Before commencing any installation or maintenance work, please disconnect the power supply from the utility. Ensure‧ that it cannot be re-connected inadvertently! Keep proper ventilation around the unit and do not stack any object on it. Also a 10-15 cm clearance must be kept when ‧ the adjacent device is a heat source. Mounting orientations other than standard orientation or operate under high ambient temperature may increase the ‧ internal component temperature and will require a de-rating in output current. Current rating of an approved primary /secondary cable should be greater than or equal to that of the unit. Please refer ‧ to its specification. For LED drivers with waterproof connectors, verify that the linkage between the unit and the lighting fixture is ‧ tight so that water cannot intrude into the system. For dimmable LED drivers, make sure that your dimming controller is capable of driving these units.PWM series ‧ require 0.15mA each unit. Tc max. is identified on the product label. Please make sure that temperature of Tc point will not exceed limit.‧ ‧Suitable for indoor use or outdoor use without direct sunlight exposure. Please avoid immerse in the water over 30 minutes. ‧The power supply is considered as a component that will be operated in combination with final equipment. Since EMC performance will be affected by the complete installation, the final equipment manufacturers must re-qualify EMC Directive on the complete installation again. +V(RED) -V(BLACK) DIM-/DA-(WHITE) DIM+/DA+(BLUE) LED Strip - ‧DALI Dimmer 0~10Vdc or 10V PWM ‧ or resistance Dimmer File Name:PWM-200-SPEC 2021-09-17 Recommend Mounting Direction