PWM-120_V01 MEANWELL | Alldatasheet
Document overview
- Manufacturer or author: Provided By alldatasheet.com(free datasheet download site)
- PDF pages: 8
Technical content
120W PWM Output LED Driver PW M -120 seri es File Name:PWM-120-SPEC 2019-05-13 IS 15885(Part 2/Sec13) R-41027766 THOMAS SAMUEL THOMAS SAMUEL ( for PWM-120-12,24 only)
120W PWM Output LED Driver PW M -120 seri es MODEL DC VOLTAGE RATED CURRENT RATED POWER OUTPUT SETUP, RISE TIME Note.2 HOLD UP TIME (Typ.) VOLTAGE RANGE Note.3 FREQUENCY RANGE POWER FACTOR (Typ.) EFFICIENCY (Typ.) AC CURRENT (Typ.) INPUT INRUSH CURRENT (Typ.) LEAKAGE CURRENT SAFETY STANDARDS Note.5 WORKING TEMP. WORKING HUMIDITY STORAGE TEMP., HUMIDITY TEMP. COEFFICIENT VIBRATION MTBF DIMENSIONOTHERS NOTE PACKING OVERLOAD OVER VOLTAGE OVER TEMPERATURE 12V 24V 36V 48V 10A 5A 3.4A 2.5A 120W 120W 122.4W 120W 0 ~ 100% 1.47kHz 500ms, 80ms/ 230VAC or 115VAC 16ms/230VAC or 115VAC 90 ~ 305VAC 127 ~ 431VDC 47 ~ 63Hz PF>0.97/115VAC, PF>0.96/230VAC, PF>0.94/277VAC @ full load (Please refer to "POWER FACTOR (PF) CHARACTERISTIC" section) 88% 90% 90% 90.5% <0.25mA / 277VAC 108 ~ 120% rated output power Hiccup mode, recovers automatically after fault condition is removed 20 ~ 95% RH non-condensing 10 ~ 500Hz, 5G 12min./1cycle, period for 72min. each along X, Y, Z axes 860.4K hrs min. Telcordia SR-332 (Bellcore) ; 228.7K hrs min. MIL-HDBK-217F (25℃) Shut down o/p voltage, re-power on to recover DIMMING RANGE PWM FREQUENCY (Typ.) ENVIRONMENT SAFETY & EMC PROTECTION Shut down o/p voltage, re-power on to recover 15 ~ 17V 28 ~ 34V 41 ~ 46V 54 ~ 60V 1.3A / 115VAC 0.65A / 230VAC 0.55A / 277VAC PWM-120-12 PWM-120-24 PWM-120-36 PWM-120-48 WITHSTAND VOLTAGE ISOLATION RESISTANCE I/P-O/P:3.75KVAC I/P-O/P:100M Ohms / 500VDC / 25℃/ 70% RH EMC IMMUNITY Compliance to EN55015, EN61000-3-2 Class C (@load≧60%) ; EN61000-3-3,GB17743 and GB17625.1,EAC TP TC 020 Compliance to EN61000-4-2,3,4,5,6,8,11; EN61547, light industry level (surge immunity Line-Line 2KV),EAC TP TC 020 EMC EMISSION Note.6 COLD START 60A(twidth=520 s measured at 50% Ipeak) at 230VAC ; Per NEMA 410 μ TOTAL HARMONIC DISTORTION 0.97Kg; 15pcs/15.6Kg/0.87CUFT MAX. NO. of PSUs on 16A CIRCUIT BREAKER 4 units (circuit breaker of type B) / 6 units (circuit breaker of type C) at 230VAC SHORT CIRCUIT (Please refer to "STATIC CHARACTERISTIC" section) THD< 20%(@load≧60%/115VAC, 230VAC; @load≧75%/277VAC) (Please refer to “TOTAL HARMONIC DISTORTION” section) No load power consumption<0.5w for blank-type;standby power consumption<0.5W for DA-type Tcase=-40 ~ + (Please refer to “ OUTPUT LOAD vs TEMPERATURE” section)90℃ Tcase=+90℃MAX. CASE TEMP. UL8750( type ”HL” )(except for 12DA type), CSA C22.2 No. 250.13-12; ENEC EN61347-1, EN61347-2-13,EN62384 independent, IP67,BIS IS15885( for PWM-120-12,24 only), EAC TP TC 004,GB19510.1,GB19510.14 approved; Design refer to EN60335-1 12V/24V hiccup mode and 36V/48V shut down mode(including DA-type) DALI STANDARDS Comply with IEC62386-101, 102, 207 for DA-Type only NO LOAD/STANDBY POWER CONSUMPTION File Name:PWM-120-SPEC 2019-05-13
◎ Applying additive 0 ~ 10VDC ◎ Applying additive 10V PWM signal (frequency range 100Hz ~ 3KHz): LED Strips LED Strips DIM+ DIM- + + - - “DO NOT connect "DIM- to -V" Additive Voltage DIM+ DIM- “DO NOT connect "DIM- to -V" Additive PWM signal 0V 1V0.6V 10% 2V 3V 4V 5V 6V 7V 8V 9V 10V 20% 30% 40% 50% 60% 70% 80% 90% 100% 10% 20% 30% 40% 50% 60% 70% 80% 90% 100% Dimming input: Additive voltage Duty cycle of additive 10V PWM signal dimming input ※ Dimming principle for PWM style output ‧Apply one of the three methodologies between DIM+ and DIM-: 0 ~ 10VDC, or 10V PWM signal or resistance. ‧Dimming source current from power supply: 100 A (typ.)μ PWM-120 ON OFF TON T Output DC current Io=0A Output PWM frequency : 1.47KHz fixed (Typ.) Duty cycle(%) = ×100% TON T ‧Dimming is achieved by varying the duty cycle of the output current. ※ 3 in 1 dimming function (for Blank-Type) 120W PWM Output LED Driver PW M -120 seri es 10%0.15% 0.15% 10% 10% Duty cycle of output current (%)Duty cycle of output current (%) AC/N(Blue) AC/L(Brown) * DIM+ for Blank-Type DA+ for DA-type * *DIM- for Blank-Type DA- for DA-type +V(Red)(Brown for DA-type) -V(Black)(Blue for DA-type) DIM+(Blue)* DIM-(White)** File Name:PWM-120-SPEC 2019-05-13
◎ Applying additive resistance: 2. The duty cycle of output current could drop down to 0% when dimming input is less than 6KΩ or less than 0.6VDC, or 10V PWM signal with duty cycle less than 6%. DIM+ DIM- “DO NOT connect "DIM- to -V" Additive Resistance 10% 20% 30% 40% 50% 60% 70% 80% 90% 100% Short 10K/N 20K/N 30K/N 40K/N 50K/N 60K/N 70K/N 80K/N 90K/N 100K/N 120W PWM Output LED Driver PW M -120 seri es ‧Apply DALI signal between DA+ and DA-. ‧DALI protocol comprises 16 groups and 64 addresses. ‧First step is fixed at 6% of output ※ DALI Interface (primary side; for DA-Type) LED Strips 6K/N 10K/N 0.15% 10% (N=driver quantity forsynchronizeddimmingoperation) Dimming input: Additive resistance Duty cycle of output current (%) File Name:PWM-120-SPEC 2019-05-13
- 30 0. 35 0. 40 0. 45 0. 50 0. 55 0. 60 0. 65 0. 70 0. 75 0. 80 0. 85 0. 90 0. 95 1. 00 10% 20% 30% 40% 50% 60% 70% 80% 90% 100% 277V 230V 115V 90 100 125 135 145 155 165 175 180 200 230 305 100 175 230VAC Input only 100 -25 0 15 3004 0 4 5 5 0-40 60 70 50 12V only 120W Output DriverPWM LED PWM-120 series PF LOAD (75W) OUTPUT LOAD TEMPERATUREvs STATIC CHARACTERISTIC TOTAL HARMONIC DISTORTION THD() AMBIENT TEMPERATURE,Ta ( )℃ LOAD (%) INPUT VOLTAGE (V) 60Hz LOAD (%) ()HORIZONTAL POWER FACTOR PF CHARACTERISTIC() Tcase ( )℃ LOAD (%) ()HORIZONTAL ※De-rating is needed under low input voltage. EFFICIENCY LOADvs PWM-120 series possess superior working efficiency that up to 90.5% can be reached in field applications. - 4 0 - 2 5 0 2 04 56 57 58 59 0 100 ※48V Model, Tcase at 80 ℃ ※48V Model, Tcase at 80 ℃ EFFICIENCY(%) LOAD THD LOAD ※Tcase at 80 ℃ 10% 20% 30% 40% 50% 60% 70% 80% 90% 100% 277V 230V 115V 10% 15% 20% 25% 30% 50% 60% 70% 80% 90% 100% 277VAC 230VAC 115VAC 230VAC Input only File Name: -120- 2019-05-13PWM SPEC
2 0 3 0 4 0 5 0 6 0 7 0 8 0 9 0 LIFETIME Tcase( )℃ LIFETIME(Kh) 120W PWM Output LED Driver PW M -120 seri es File Name:PWM-120-SPEC 2019-05-13
120W PWM Output LED Driver PW M -120 seri es Mechanical Specification Case No. PWM-120 Unit:mm Block Diagram DETECTION DIMMING PWM & PFC CIRCUIT CIRCUIT EMI FILTER RECTIFIERS POWER SWITCHING FILTER RECTIFIERS +V -VI/P CONTROL O.V.P. O.L.P. PFC CIRCUIT PFC fosc : 50~120KHz PWM fosc : 60~130KHz DIM+ DIM- AC/N(Blue) AC/L(Brown) 37.5 191300 20± 300 20± T case 31.5 95.5tc ‧ : Max. Case Temperaturetc UL2464 18AWG×2C SJTW 14AWG×2C +V(Red) -V(Black) DIM+(Blue) DIM-(White) 50±3 SJTW 18AWG×2C 50±3 2-ψ4.5 File Name:PWM-120-SPEC 2019-05-13 AC/N(Blue) AC/L(Brown) 37.5 191300 20± 300 20± T case 31.5 95.5tc ‧ : Max. Case Temperaturetc UL2464 18AWG×2C +V(Brown) -V(Blue) DA+(Blue) DA-(White) 50±3 SJOW 17AWG×2C 50±3 2-ψ4.5 ※ Blank-Type ※ DA-Type &H05RN-F 1.0mm SJOW 17AWG×2C2 &H05RN-F 1.0mm
120W PWM Output LED Driver PW M -120 seri es Installation Manual AC/L(BROWN) AC/N(BLUE) ◎Connection for Blank-type ◎Cautions Before commencing any installation or maintenance work, please disconnect the power supply from the utility. Ensure‧ that it cannot be re-connected inadvertently! Keep proper ventilation around the unit and do not stack any object on it. Also a 10-15 cm clearance must be kept when ‧ the adjacent device is a heat source. Mounting orientations other than standard orientation or operate under high ambient temperature may increase the ‧ internal component temperature and will require a de-rating in output current. Current rating of an approved primary /secondary cable should be greater than or equal to that of the unit. Please refer ‧ to its specification. For LED drivers with waterproof connectors, verify that the linkage between the unit and the lighting fixture is ‧ tight so that water cannot intrude into the system. For dimmable LED drivers, make sure that your dimming controller is capable of driving these units.PWM series ‧ require 0.15mA each unit. Tc max. is identified on the product label. Please make sure that temperature of Tc point will not exceed limit.‧ DO NOT connect "DIM- to -V".‧ ‧Suitable for indoor use or outdoor use without direct sunlight exposure. Please avoid immerse in the water over 30 minutes. ‧The power supply is considered as a component that will be operated in combination with final equipment. Since EMC performance will be affected by the complete installation, the final equipment manufacturers must re-qualify EMC Directive on the complete installation again. ‧For more information about installation, http://www.meanwell.com/manual.html for details.Please refer to : +V(RED) -V(BLACK) DIM-(WHITE) DIM+(BLUE) LED Strip - 0~10Vdc or 10V PWM or resistance Dimmer File Name:PWM-120-SPEC 2019-05-13 Recommend Mounting Direction