PTPUL2T323PWR

TPUL2T323 TI | Alldatasheet

Document overview

• Manufacturer or author: Provided By alldatasheet.com(free datasheet download site)
• PDF pages: 40

Technical content

TPUL2T323 Dual Retriggerable Extended RC-Timed Monostable Multivibrators

1 Features

• RC configurable from 10ms to 880s
• Extended pulse width functionality reduces capacitor value required for long pulse widths by factor of 1000
• For pulses less than 10ms, use
• 1% typical, 10% maximum pulse width variation
• Wide operating range of 1.5V to 5.5V
• Inputs accept voltages up to 5.5V
• TTL-compatible with 4.5V to 5.5V supply
• Schmitt-trigger architecture on all inputs
• Single-supply voltage translator (refer to Reduced Input Threshold Voltage): – Up translation:
• 1.2V to 1.8V
• 1.5V to 2.5V
• 1.8V to 3.3V
• 3.3V to 5.0V – Down translation:
• 5.0V, 3.3V to 2.5V
• 5.0V to 3.3V

2 Applications

• Demodulate a digital Amplitude Shift Keying (ASK) signal
• Reset a system for a fixed period of time
• Generate a positive fixed-width digital pulse
• Detect a digital signal rising edge
• Detect a digital signal falling edge
• Debounce a switch

3 Description

The TPUL2T323 device contains two independent extended-pulse-width RC-configurable retriggerable monostable multivibrators designed for 1.5V to 5.5V operation. The output pulse duration is configured by selecting external resistance and capacitance values with an approximate output pulse width of t wo ≅ 1000 × R × C. This device features three inputs, allowing for rising edge (T) and falling edge (T) triggers and a clear input (CLR) that can be used asynchronously to stop an active output pulse. All inputs include Schmitt-trigger architecture to allow for slow input transition rates and improve noise immunity. Device Information PART NUMBER PACKAGE (1) PACKAGE SIZE(2) BODY SIZE TPUL2T323 PW (TSSOP, 16) 5mm × 6.4mm 5mm × 4.4mm (1) For all available packages, see the orderable addendum at the end of the data sheet. (2) The package size (length × width) is a nominal value and includes pins, where applicable. Product Group T P U L TPUL

2 G 1 2 3 Q 1

G : Standard T : Reduced Timing Type 1 : RC 1x, Retrig 2 : RC 1x, Non-retrig 3 : RC 1000x, Retrig Output(s) 0 : Active Low 1 : Active High 2 : Both Input(s) 0 : Falling edge (FE) 1 : Rising edge (RE) 2 : FE, RE, async clear 3 : FE, RE, async clear, and trigger on clear release Rating [none] : Commercial / Industrial -Q1 : Automotive, AEC-Q100 TPUL Family Naming Convention TPUL2T323 SCASE79A – APRIL 2025 – REVISED SEPTEMBER 2025 An IMPORTANT NOTICE at the end of this data sheet addresses availability, warranty, changes, use in safety-critical applications, intellectual property matters and other important disclaimers. PRODUCTION DATA.

11 Mechanical, Packaging, and Orderable

SCASE79A – APRIL 2025 – REVISED SEPTEMBER 2025 www.ti.com

2 Submit Document Feedback Copyright © 2025 Texas Instruments Incorporated

Product Folder Links: TPUL2T323

4 Pin Configuration and Functions

See mechanical drawings for dimensions. Figure 4-1. PW Package 16-Pin TSSOP Top View Table 4-1. Pin Functions PIN I/O(1) DESCRIPTION NAME NO. 1T 1 I Channel 1 falling edge trigger input; requires 1T and 1CLR to be held high 1T 2 I Channel 1 rising edge trigger input; requires 1T to be held low and 1CLR to be held high 1CLR 3 I Channel 1 asynchronous clear input, active low; also can operate as rising edge trigger input if 1T is held low and 1T is held high 1Q 4 O Channel 1 inverted output 2Q 5 O Channel 2 output 2C 6 G Channel 2 external timing capacitor negative connection; provides a return path for discharge current of the external timing capacitor; internally connected to ground 2RC 7 I/O Channel 2 external timing node connection; see Application Information section for detailed operation instructions GND 8 G Ground 2T 9 I Channel 2 falling edge trigger input; requires 2T and 2CLR to be held high 2T 10 I Channel 2 rising edge trigger input; requires 2T to be held low and 2CLR to be held high 2CLR 11 I Channel 2 asynchronous clear input, active low; also can operate as rising edge trigger input if 2T is held low and 2T is held high 2Q 12 O Channel 2 inverted output 1Q 13 O Channel 1 output 1C 14 G Channel 1 external timing capacitor negative connection; provides a return path for discharge current of the external timing capacitor; internally connected to ground 1RC 15 I/O Channel 1 external timing node connection; see Application Information section for detailed operation instructions VCC 16 P Postive voltage supply (1) I = Input, O = Output, I/O = Input and output, G = Ground, P = Power www.ti.com TPUL2T323 SCASE79A – APRIL 2025 – REVISED SEPTEMBER 2025 Copyright © 2025 Texas Instruments Incorporated Submit Document Feedback 3 Product Folder Links: TPUL2T323

5 Specifications

5.1 Absolute Maximum Ratings

over operating free-air temperature range (unless otherwise noted)(1) MIN MAX UNIT VCC Supply voltage range –0.5 6.5 V VI Digital input voltage range(2) –0.5 6.5 V VO Digital output voltage range in the active state(2) –0.5 VCC + 0.5 V VO Digital output voltage range in the high-impedance state(2) –0.5 6.5 V VRC RC pin voltage range –0.5 VCC + 0.5 V IIK Input clamp diode current, continuous VI < -0.5V –20 mA Input clamp diode current, pulsed 1µs VI < -0.5V –200 mA IOK Output clamp diode current, continuous VO < -0.5V –20 mA Output clamp diode current, pulsed 1µs VO < -0.5V –200 mA IO Digital output current, continuous VO = 0 to VCC ±50 mA Digital output current, pulsed 1µs VO = 0 to VCC ±200 mA Continuous current through VCC or GND ±200 mA Rext External timing resistance 1 kΩ Cext External timing capacitance 1(3) µF TJ Junction temperature 150 °C Tstg Storage temperature –65 150 °C (1) Operation outside the Absolute Maximum Ratings may cause permanent device damage. Absolute maximum ratings do not imply functional operation of the device at these or any other conditions beyond those listed under Recommended Operating Conditions. If briefly operating outside the Recommended Operating Conditions but within the Absolute Maximum Ratings, the device may not sustain damage, but it may not be fully functional. Operating the device in this manner may affect device reliability, functionality, performance, and shorten the device lifetime. (2) The voltage ratings may be exceeded if the associated clamp current ratings are observed. (3) The timing capacitance maximum value may be exceeded if an external diode is added. See Application and Implementation section for details.

5.2 ESD Ratings

V(ESD) Electrostatic discharge Human-body model (HBM), per ANSI/ESDA/JEDEC JS-001(1) ±2000 V Charged-device model (CDM), per ANSI/ESDA/JEDEC JS-002(2) ±1000 (1) JEDEC document JEP155 states that 500V HBM allows safe manufacturing with a standard ESD control process. (2) JEDEC document JEP157 states that 250V CDM allows safe manufacturing with a standard ESD control process. TPUL2T323 SCASE79A – APRIL 2025 – REVISED SEPTEMBER 2025 www.ti.com

4 Submit Document Feedback Copyright © 2025 Texas Instruments Incorporated

Product Folder Links: TPUL2T323

5.3 Recommended Operating Conditions

over operating free-air temperature range (unless otherwise noted) Spec Description Condition MIN MAX UNIT VCC Supply voltage 1.5 5.5 V VI (1) Input Voltage 0 5.5 V VO Output Voltage 0 VCC V IOH (2) High-level output current VCC = 1.5V –4 mA VCC = 1.8V –6 mA VCC = 2.5V –26 mA VCC = 3.3V –50 mA VCC = 5V –50 mA IOL (2) Low-level output current VCC = 1.5V 4 mA VCC = 1.8V 6 mA VCC = 2.5V 26 mA VCC = 3.3V 50 mA VCC = 5V 50 mA Rext (3) External timing resistance VCC = 1.5V to 5.5V 6.5 1000 kΩ Cext (3) External timing capacitance VCC = 1.5V to 5.5V 0.1 1000 nF two Configured output pulse width VCC = 1.5V to 5.5V 0.01 880 s CL Digital output load capacitance VCC = 1.5V to 5.5V 50 pF VPOR Power-on reset ramp voltage Δt/ΔVCC ≥ 20µs/V 0.3 1.5 V Δt/ΔVCC Power-on ramp rate VCC = 0.3V to 1.5V 20 µs/V Δt/Δv Input transition rise or fall rate VCC = 1.5V to 5.5V 100 ms/V TA Operating free-air temperature Operating free-air temperature –40 125 °C (1) All unused inputs of the device must be held at VCC or GND to ensure proper device operation. (2) Recommended maximum output current for continuous operation; see Electrical Characteristics for test current values to maintain VOH and VOL specifications. Operating with average output current greater than 12mA may impact device reliability and shorten the device lifetime. (3) Recommended Rext and Cext values maintain maximum error provided as Δtwo in the Switching Characteristics table.

5.4 Thermal Information

THERMAL METRIC(1) UNIT RθJA RθJC(top) RθJB ΨJT ΨJB RθJC(bot) (1) For more information about traditional and new thermal metrics, see the Semiconductor and IC Package Thermal Metrics application note. www.ti.com TPUL2T323 SCASE79A – APRIL 2025 – REVISED SEPTEMBER 2025 Copyright © 2025 Texas Instruments Incorporated Submit Document Feedback 5 Product Folder Links: TPUL2T323

5.5 Electrical Characteristics

Over operating free-air temperature range; typical values measured at TA = 25°C (unless otherwise noted) PARAMETER TEST CONDITIONS VCC MIN TYP MAX UNIT VT+ Positive switching threshold 1.5V 0.65 0.84 0.96 V 1.8V 0.73 0.95 1.11 2.5V 0.88 1.11 1.33 3.3V 1.03 1.27 1.5 5V 1.33 1.58 1.82 5.5V 1.41 1.67 1.91 VT- Negative switching threshold 1.5V 0.32 0.41 0.5 V 1.8V 0.36 0.46 0.53 2.5V 0.45 0.55 0.63 3.3V 0.54 0.65 0.74 5V 0.7 0.85 0.96 5.5V 0.74 0.89 1.02 ΔVT Hysteresis (VT+ - VT-) 1.5V 0.33 0.45 0.6 V 1.8V 0.36 0.5 0.65 2.5V 0.42 0.56 0.72 3.3V 0.49 0.62 0.78 5V 0.61 0.74 0.91 5.5V 0.65 0.77 0.95 VOH High-level output voltage IOH = -50µA 1.5V - 5.5V VCC – 0.1 VCC – 0.01 V IOH = -1mA 1.65V 1.2 1.61 IOH = -2mA 2.3V 2.1 2.24 IOH = -8mA 3V 2.4 2.78 IOH = -12mA 4.5V 3.94 4.21 IOH = -12mA 5.5V 4.94 5.23 V VOL Low-level output voltage IOL = 50µA 1.5V - 5.5V 0.01 0.1 V IOL = 1mA 1.65V 0.03 0.45 IOL = 2mA 2.3V 0.04 0.2 IOL = 8mA 3V 0.13 0.4 IOL = 12mA 4.5V 0.15 0.5 IOL = 12mA 5.5V 0.13 0.5 II Input leakage current VI = 5.5V or 0V 0V to 5.5V ±50 nA ICEXT Capacitor pin current Monitor state, VCEXT = 0.5 × VCC 1.5V to 5.5V ±50 nA ICEXT Capacitor pin current Active state, discharging, VCEXT = 1.5V 1.5V 11 mA Active state, discharging, VCEXT = 2.3V 2.3V 29 mA Active state, discharging, VCEXT = 3V 3V 45 mA Active state, discharging, VCEXT = 4.5V 4.5V 95 mA Active state, discharging, VCEXT = 5.5V 5.5V 138 mA Ioff Partial power- off current VI or VO = 5.5V or 0V 0V to 0.3V 0.25 10 µA ICC Supply current Ready state, VI = VCC or 0V, IO = 0 5.5V 0.19 2 µA TPUL2T323 SCASE79A – APRIL 2025 – REVISED SEPTEMBER 2025 www.ti.com

6 Submit Document Feedback Copyright © 2025 Texas Instruments Incorporated

Product Folder Links: TPUL2T323

Over operating free-air temperature range; typical values measured at TA = 25°C (unless otherwise noted) PARAMETER TEST CONDITIONS VCC MIN TYP MAX UNIT ICC Supply current Active state per channel, VI = VCC or 0V, IO = 0 1.5V 180 µA 1.65V 200 2.3V 290 3V 450 4.5V 836 5.5V 1126 ΔICC Supply-current change One input, Vi = 0 to VCC, all other inputs at VCC or 0V, IO = 0mA 1.5V to 5.5V 2.1 mA CI Input capacitance VI = 5.5V or 0V 5.5V 1 pF CO Output capacitance VO = 5.5V or 0V 0V 3 pF Cint Internal capacitance Cext = 0pF; Vcext = 0 to VCC 1.5V 16 17.9 20 pF 1.65V 14 15.5 17 2.3V 7 9.7 13 3V 6 9.9 14 4.5V 5 7.7 10 5.5V 4 5.7 7

5.6 Timing Characteristics

over recommended operating free-air temperature range (unless otherwise noted) PARAMETER DESCRIPTION CONDITION VCC MIN MAX UNIT twi Pulse duration Any trigger input 1.5V 18.2 ns 1.8V ± 0.15V 9.9 2.5V ± 0.2V 7.8 3.3V ± 0.3V 5.8 5V ± 0.5V 4.1 tsu Setup time between trigger inputs T low before T↑ or CLR↑ 1.5V 9.6 ns 1.8V ± 0.15V 8 2.5V ± 0.2V 6.9 3.3V ± 0.3V 6.6 5V ± 0.5V 6.5 T high before T↓ or CLR↑ 1.5V 5 ns 1.8V ± 0.15V 5 2.5V ± 0.2V 5 3.3V ± 0.3V 5 5V ± 0.5V 5 CLR high before T↓ or T↑ 1.5V 9.2 ns 1.8V ± 0.15V 7.8 2.5V ± 0.2V 6.7 3.3V ± 0.3V 6.5 5V ± 0.5V 6.4 www.ti.com TPUL2T323 SCASE79A – APRIL 2025 – REVISED SEPTEMBER 2025 Copyright © 2025 Texas Instruments Incorporated Submit Document Feedback 7 Product Folder Links: TPUL2T323

over recommended operating free-air temperature range (unless otherwise noted) PARAMETER DESCRIPTION CONDITION VCC MIN MAX UNIT th Hold time Any trigger input 1.5V 9.3 ns 1.8V ± 0.15V 7.8 2.5V ± 0.2V 6.7 3.3V ± 0.3V 6.5 5V ± 0.5V 6.4 trr (1) Retrigger time Any trigger input, Rext = 100kΩ, Cext = 100pF 1.5V 13.1 µs 1.8V ± 0.15V 13 2.5V ± 0.2V 12.6 3.3V ± 0.3V 12.5 5V ± 0.5V 12.2 Any trigger input, Rext = 10kΩ, Cext = 0.1µF 1.5V 2 ms 1.8V ± 0.15V 2 2.5V ± 0.2V 2 3.3V ± 0.3V 2.1 5V ± 0.5V 2.1 Any trigger input, Rext = 10kΩ, Cext = 10µF 1.5V 912 ms 1.8V ± 0.15V 911 2.5V ± 0.2V 904 3.3V ± 0.3V 893 5V ± 0.5V 864 tstartup (2) Startup time 1.5V to 5.5V 0 µs (1) Triggering the clear input (CLR) more often than 2500 × Cext may affect long-term reliability of the device. Repeated fast triggering of the clear input causes excessive average current at the RC pin. (2) Triggers received during device startup may be ignored. The external timing capacitor requires time to charge after startup. For optimal first pulse accuracy, wait a minimum of 500 × Cext after supply voltage has reached stable operating conditions before applying the first trigger. T T CLR RC Q Q Rising Edge Trigger Falling Edge Trigger Clear Clear Release Trigger Ignore Falling Edge Trigger Retrigger Ignore Clear Release Figure 5-1. Input/Output Timing Diagram TPUL2T323 SCASE79A – APRIL 2025 – REVISED SEPTEMBER 2025 www.ti.com

8 Submit Document Feedback Copyright © 2025 Texas Instruments Incorporated

Product Folder Links: TPUL2T323

5.7 Switching Characteristics

over operating free-air temperature range; typical values measured at TA = 25°C (unless otherwise noted). See Parameter Measurement Information. PARAME TER FROM (INPUT) TO (OUTPUT) TEST CONDITIONS VCC MIN TYP MAX UNIT CL = 15pF tpd T, T, or CLR Q or Q CL = 15pF 1.5V 7 35 59 ns 1.65V 6 28.6 47 2.3V 4 16.6 26 3V 3 12.4 19 4.5V 2 9.4 13 5.5V 2 9.2 12 tt Q or Q CL = 15pF 1.5V 4.3 8.3 ns 1.65V 3.9 7 2.3V 3 5.6 3V 2.5 5 4.5V 2.4 4.9 5.5V 2.7 5.8 CL = 50pF tpd T, T, or CLR Q or Q CL = 50pF 1.5V 7 37 67 ns 1.65V 6 30.2 53 2.3V 4 17.6 30 3V 3 13 22 4.5V 2 9.8 16 5.5V 2 9.6 14 two (1) Q or Q Rext = 1MΩ; Cext = 0; CL = 50pF 1.5V 2.3 3.6 4.4 ms 1.65V 2.5 3.5 4.3 2.3V 2.2 3.4 4.1 3V 2.2 3.3 4 4.5V 2.1 3.2 3.8 5.5V 2 3.1 3.8 Rext = 10kΩ; Cext = 0.1µF; CL = 50pF 1.5V 831 934 1017 ms 1.65V 832 934 1018 2.3V 837 932 1024 3V 842 938 1030 4.5V 852 949 1043 5.5V 857 954 1049 Rext = 330kΩ; Cext = 1µF; CL = 50pF 1.5V 261 295 324 s 1.65V 250 301 316 2.3V 253 298 315 3V 255 300 317 4.5V 261 306 320 5.5V 264 310 323 Δtwo (2) Q or Q CL = 50pF 1.5V to 5.5V ±1 ±10 % www.ti.com TPUL2T323 SCASE79A – APRIL 2025 – REVISED SEPTEMBER 2025 Copyright © 2025 Texas Instruments Incorporated Submit Document Feedback 9 Product Folder Links: TPUL2T323

over operating free-air temperature range; typical values measured at TA = 25°C (unless otherwise noted). See Parameter Measurement Information. PARAME TER FROM (INPUT) TO (OUTPUT) TEST CONDITIONS VCC MIN TYP MAX UNIT tt Q or Q CL = 50pF 1.5V 8.2 34.4 ns 1.65V 7 28 2.3V 4.5 24.6 3V 3.9 17.4 4.5V 3.1 12.6 5.5V 2.9 8.7 Cpd (3) CLR T = VCC, T = GND fI = 10MHz CL = 50pF Cext = 0pF Rext = 1MΩ 1.5V 46 pF 1.65V 46 2.3V 49 3V 40 4.5V 47 5.5V 49 (1) Output pulse width (2) Variation in output pulse width as compared to typical characteristics for K factor excluding variations in external timing components. (3) Power dissipation capacitance is calculated in accordance with CMOS Power Consumption and Cpd Calculation. TPUL2T323 SCASE79A – APRIL 2025 – REVISED SEPTEMBER 2025 www.ti.com

10 Submit Document Feedback Copyright © 2025 Texas Instruments Incorporated

Product Folder Links: TPUL2T323

5.8 Typical Characteristics

TA = 25°C (unless otherwise noted) Table 5-1. Pulse width using common RC, VCC = 3.3V Resistor Value Capacitor Value 10µF 1µF 100nF 10nF 1nF 100pF 10pF 15kΩ 143s 14.3s 1.44s 149ms 16.1ms 1.92ms(1) 281µs(1) 22kΩ 209s 20.9s 2.12s 218ms 23.4ms 2.79ms(1) 387µs(1) 33kΩ 313s 31.3s 3.16s 327ms 35.3ms 4.14ms(1) 552µs(1) 47kΩ 444s 44.4s 4.50s 464ms 49.8ms 5.88ms(1) 763µs(1) 100kΩ 946s 94.6s 9.58s 985ms 106ms 12.5ms 1.55ms(1) 150kΩ 1420s 142s 14.3s 1.48s 160ms 18.5ms 2.29ms(1) 220kΩ 2080s 208s 21.0s 2.17s 234ms 27.3ms 3.32ms(1) 330kΩ 2924s(2) 312s 31.5s 3.25s 351ms 40.6ms 4.94ms(1) 470kΩ 2939s(2) 444s 44.9s 4.64s 501ms 58.0ms 7.02ms(1) 680kΩ 2962s(2) 643s 64.9s 6.69s 724ms 84.3ms 10.1ms 1MΩ 2995s(2) 940s 95.8s 9.88s 1.06s 125ms 14.8ms (1) Pulse widths configured for less than 10ms (K×R×C < 10µs) can fail to properly trigger the state machine resulting in very short output pulses (two < 10µs). (2) Pulse widths configured for more than 2253s (K×R×C > 2.2s) can vary significantly due to exceeding the digital timing circuitry capabilities. Supply Voltage (V) Supply Current ( 0.1 0.2 0.3 0.4 0.5 0.6 0.7 0.8 0.9 1.0 -40C 25C 85C 125C Figure 5-2. Supply Current vs Supply Voltage Input Voltage (V) Supply Current (mA) -0.2 0.2 0.4 0.6 0.8 1.0 1.2 1.4 1.6 1.8 1.5V 1.8V 2.5V 3.3V 4.5V 5.5V Figure 5-3. Supply Current vs Input Voltage www.ti.com TPUL2T323 SCASE79A – APRIL 2025 – REVISED SEPTEMBER 2025 Copyright © 2025 Texas Instruments Incorporated Submit Document Feedback 11 Product Folder Links: TPUL2T323

Output Current (mA) Output Low-State Resistance () 0 2 4 6 8 10 12 12.5 17.5 22.5 27.5 32.5 1.65V 2.3V 4.5V 5.5V 1 3 5 7 9 11 Figure 5-4. Output Low-State Resistance vs Output Current Output Current (mA) Output High-State Resistance () 22.5 27.5 32.5 37.5 1.65V 2.3V 4.5V 5.5V Figure 5-5. Output High-State Resistance vs Output Current T e m p e r a t u r e (  C ) K Factor - 4 0 - 2 0 0 2 0 4 0 6 0 8 0 1 0 0 1 2 0 0 . 8 5 0 . 8 7 0 . 8 9 0 . 9 1 0 . 9 3 0 . 9 5 0 . 9 7 0 . 9 9 1 . 0 1 1 . 0 3 1 . 0 5 1 . 0 7 1 . 0 9 1 . 1 1 1 . 1 3 1 . 1 5 1 n F 1 0 n 1 0 0 n F 1  F Figure 5-6. K Factor vs Temperature, Rext = 10kΩ S u p p l y V o l t a g e ( V ) K Factor 0 . 8 5 0 . 8 7 0 . 8 9 0 . 9 1 0 . 9 3 0 . 9 5 0 . 9 7 0 . 9 9 1 . 0 1 1 . 0 3 1 . 0 5 1 . 0 7 1 . 0 9 1 . 1 1 1 n F 1 0 n F 1 0 0 n F 1  F Figure 5-7. K Factor vs Supply Voltage, Rext = 10kΩ E x t e r n a l T i m in g C a p a c it a n c e , C e x t ( F ) K Factor 1 E - 1 1 2 E - 1 1 5 E - 1 1 1 E - 1 0 2 E - 1 0 5 E - 1 0 1 E - 9 2 E - 9 5 E - 9 1 E - 8 2 E - 8 5 E - 8 1 E - 7 2 E - 7 5 E - 7 1 E - 6 1 0 1 1 1 2 1 3 1 4 1 5 1 6 1 7 1 8 1 k  2 k  5 k  1 0 k  Figure 5-8. K Factor, VCC = 1.5V, Rext = 1kΩ to 10kΩ TPUL2T323 SCASE79A – APRIL 2025 – REVISED SEPTEMBER 2025 www.ti.com

12 Submit Document Feedback Copyright © 2025 Texas Instruments Incorporated

Product Folder Links: TPUL2T323

E x t e r n a l T i m in g C a p a c it a n c e , C e x t ( F ) K Factor 1 E - 1 1 2 E - 1 1 5 E - 1 1 1 E - 1 0 2 E - 1 0 5 E - 1 0 1 E - 9 2 E - 9 5 E - 9 1 E - 8 2 E - 8 5 E - 8 1 E - 7 2 E - 7 5 E - 7 1 E - 6 0 . 8 1 . 2 1 . 4 1 . 6 1 . 8 2 . 2 2 . 4 2 . 6 2 . 8 1 0 k  2 0 k  5 0 k  1 0 0 k  2 0 0 k  5 0 0 k 

1 M 

Figure 5-9. K Factor, VCC = 1.5V, Rext = 10kΩ to 1MΩ E x t e r n a l T i m in g C a p a c it a n c e , C e x t ( F ) K Factor 1 E - 1 1 2 E - 1 1 5 E - 1 1 1 E - 1 0 2 E - 1 0 5 E - 1 0 1 E - 9 2 E - 9 5 E - 9 1 E - 8 2 E - 8 5 E - 8 1 E - 7 2 E - 7 5 E - 7 1 E - 6 1 0 1 1 1 2 1 3 1 k  2 k  5 k  1 0 k  Figure 5-10. K Factor, VCC = 1.8V, Rext = 1kΩ to 10kΩ E x t e r n a l T i m in g C a p a c it a n c e , C e x t ( F ) K Factor 1 E - 1 1 2 E - 1 1 5 E - 1 1 1 E - 1 0 2 E - 1 0 5 E - 1 0 1 E - 9 2 E - 9 5 E - 9 1 E - 8 2 E - 8 5 E - 8 1 E - 7 2 E - 7 5 E - 7 1 E - 6 0 . 8 0 . 9 1 . 1 1 . 2 1 . 3 1 . 4 1 . 5 1 . 6 1 . 7 1 . 8 1 . 9 2 . 1 2 . 2 2 . 3 2 . 4 2 . 5 2 . 6 1 0 k  2 0 k  5 0 k  1 0 0 k  2 0 0 k  5 0 0 k  Figure 5-11. K Factor, VCC = 1.8V, Rext = 10kΩ to 1MΩ www.ti.com TPUL2T323 SCASE79A – APRIL 2025 – REVISED SEPTEMBER 2025 Copyright © 2025 Texas Instruments Incorporated Submit Document Feedback 13 Product Folder Links: TPUL2T323

E x t e r n a l T i m in g C a p a c it a n c e , C e x t ( F ) K Factor 1 E - 1 1 2 E - 1 1 5 E - 1 1 1 E - 1 0 2 E - 1 0 5 E - 1 0 1 E - 9 2 E - 9 5 E - 9 1 E - 8 2 E - 8 5 E - 8 1 E - 7 2 E - 7 5 E - 7 1 E - 6 1 0 1 1 1 k  2 k  5 k  1 0 k  Figure 5-12. K Factor, VCC = 2.5V, Rext = 1kΩ to 10kΩ E x t e r n a l T i m in g C a p a c it a n c e , C e x t ( F ) K Factor 1 E - 1 1 2 E - 1 1 5 E - 1 1 1 E - 1 0 2 E - 1 0 5 E - 1 0 1 E - 9 2 E - 9 5 E - 9 1 E - 8 2 E - 8 5 E - 8 1 E - 7 2 E - 7 5 E - 7 1 E - 6 0 . 8 0 . 9 1 . 1 1 . 2 1 . 3 1 . 4 1 . 5 1 . 6 1 . 7 1 . 8 1 . 9 2 . 1 1 0 k  2 0 k  5 0 k  1 0 0 k  2 0 0 k  5 0 0 k  Figure 5-13. K Factor, VCC = 2.5V, Rext = 10kΩ to 1MΩ E x t e r n a l T i m in g C a p a c it a n c e , C e x t ( F ) K Factor 1 E - 1 1 2 E - 1 1 5 E - 1 1 1 E - 1 0 2 E - 1 0 5 E - 1 0 1 E - 9 2 E - 9 5 E - 9 1 E - 8 2 E - 8 5 E - 8 1 E - 7 2 E - 7 5 E - 7 1 E - 6 0 . 5 1 . 5 2 . 5 3 . 5 4 . 5 5 . 5 1 k  2 k  5 k  1 0 k  Figure 5-14. K Factor, VCC = 3.3V, Rext = 1kΩ to 10kΩ TPUL2T323 SCASE79A – APRIL 2025 – REVISED SEPTEMBER 2025 www.ti.com

14 Submit Document Feedback Copyright © 2025 Texas Instruments Incorporated

Product Folder Links: TPUL2T323

E x t e r n a l T i m in g C a p a c it a n c e , C e x t ( F ) K Factor 1 E - 1 1 2 E - 1 1 5 E - 1 1 1 E - 1 0 2 E - 1 0 5 E - 1 0 1 E - 9 2 E - 9 5 E - 9 1 E - 8 2 E - 8 5 E - 8 1 E - 7 2 E - 7 5 E - 7 1 E - 6 0 . 8 0 . 9 1 . 1 1 . 2 1 . 3 1 . 4 1 . 5 1 . 6 1 . 7 1 . 8 1 . 9 1 0 k  2 0 k  5 0 k  1 0 0 k  2 0 0 k  5 0 0 k  Figure 5-15. K Factor, VCC = 3.3V, Rext = 10kΩ to 1MΩ E x t e r n a l T i m in g C a p a c it a n c e , C e x t ( F ) K Factor 1 E - 1 1 2 E - 1 1 5 E - 1 1 1 E - 1 0 2 E - 1 0 5 E - 1 0 1 E - 9 2 E - 9 5 E - 9 1 E - 8 2 E - 8 5 E - 8 1 E - 7 2 E - 7 5 E - 7 1 E - 6 0 . 8 1 . 2 1 . 4 1 . 6 1 . 8 2 . 2 2 . 4 2 . 6 2 . 8 3 . 2 3 . 4 3 . 6 3 . 8 4 . 2 4 . 4 4 . 6 1 k  2 k  5 k  1 0 k  Figure 5-16. K Factor, VCC = 5V, Rext = 1kΩ to 10kΩ E x t e r n a l T i m in g C a p a c it a n c e , C e x t ( F ) K Factor 1 E - 1 1 2 E - 1 1 5 E - 1 1 1 E - 1 0 2 E - 1 0 5 E - 1 0 1 E - 9 2 E - 9 5 E - 9 1 E - 8 2 E - 8 5 E - 8 1 E - 7 2 E - 7 5 E - 7 1 E - 6 0 . 8 0 . 9 1 . 1 1 . 2 1 . 3 1 . 4 1 . 5 1 . 6 1 . 7 1 . 8 1 0 k  2 0 k  5 0 k  1 0 0 k  2 0 0 k  5 0 0 k  Figure 5-17. K Factor, VCC = 5V, Rext = 10kΩ to 1MΩ www.ti.com TPUL2T323 SCASE79A – APRIL 2025 – REVISED SEPTEMBER 2025 Copyright © 2025 Texas Instruments Incorporated Submit Document Feedback 15 Product Folder Links: TPUL2T323

E x t e r n a l T i m in g C a p a c it a n c e , C e x t ( F ) K Factor 1 E - 1 1 2 E - 1 1 5 E - 1 1 1 E - 1 0 2 E - 1 0 5 E - 1 0 1 E - 9 2 E - 9 5 E - 9 1 E - 8 2 E - 8 5 E - 8 1 E - 7 2 E - 7 5 E - 7 1 E - 6 0 . 8 1 . 2 1 . 6 2 . 4 2 . 8 3 . 2 3 . 6 4 . 4 4 . 8 5 . 2 1 k  2 k  5 k  1 0 k  Figure 5-18. K Factor, VCC = 5.5V, Rext = 1kΩ to 10kΩ E x t e r n a l T i m in g C a p a c it a n c e , C e x t ( F ) K Factor 1 E - 1 1 2 E - 1 1 5 E - 1 1 1 E - 1 0 2 E - 1 0 5 E - 1 0 1 E - 9 2 E - 9 5 E - 9 1 E - 8 2 E - 8 5 E - 8 1 E - 7 2 E - 7 5 E - 7 1 E - 6 0 . 8 0 . 9 1 . 1 1 . 2 1 . 3 1 . 4 1 . 5 1 . 6 1 . 7 1 0 k  2 0 k  5 0 k  1 0 0 k  2 0 0 k  5 0 0 k  Figure 5-19. K Factor, VCC = 5.5V, Rext = 10kΩ to 1MΩ External Timing Capacitance (Cext) Minimum Retrigger Time (trr) 5pF 100pF 1nF 10nF 100nF 1 F 10 F 20ns 100ns s 10 s 100 s 1ms 5ms 1.5V 1.65V 2.3V 4.5V 5.5V Figure 5-20. Minimum retrigger time versus external timing capacitor value External Timing Resistance (Rext) Maximum Retrigger Time Error (%) 1k 2k 5k 10k 100k 1M 0.02 0.05 0.1 0.2 0.5 100 200 1.5V 2.3V 4.5V 5.5V Figure 5-21. Maximum retrigger time error as a percentage of total pulse width versus external timing resistor value Error data in the following plots indicates changes from typical behavior (nominal material, T A = 25°C) due to variation in manufacturing process and operating free-air temperature. TPUL2T323 SCASE79A – APRIL 2025 – REVISED SEPTEMBER 2025 www.ti.com

16 Submit Document Feedback Copyright © 2025 Texas Instruments Incorporated

Product Folder Links: TPUL2T323

6 Parameter Measurement Information

Phase relationships between waveforms were chosen arbitrarily for the examples listed in the following table. All input pulses are supplied by generators having the following characteristics: PRR ≤ 1MHz, ZO = 50Ω, tt < 2.5ns. The outputs are measured individually with one input transition per measurement. CL (1) From Output Under Test Test Point (1) CL includes probe and test-fixture capacitance. Figure 6-1. Load Circuit for Push-Pull Outputs 50% tw Input 50% VCC 0 V Figure 6-2. Voltage Waveforms, Pulse Duration Clock Input 50% VCC 0 V 50% 50% VCC 0 V tsu Data Input th Figure 6-3. Voltage Waveforms, Setup and Hold Times 50%Input 50% VCC 0 V 50% 50% VOH VOL tPLH (1) tPHL (1) VOH VOL tPHL (1) tPLH (1) Output Output 50% 50% (1) The greater between tPLH and tPHL is the same as tpd. Figure 6-4. Voltage Waveforms Propagation Delays VOH VOL Output VCC 0 V Input tf (1)tr (1) 90% 10% 90% 10% tr (1) 90% 10% tf (1) 90% 10% (1) The greater between tr and tf is the same as tt. Figure 6-5. Voltage Waveforms, Input and Output Transition Times Trigger Input VCC 0 V trr 0.5VCC Trigger Event Trigger Event Figure 6-6. Voltage Waveforms, Retrigger Time TPUL2T323 SCASE79A – APRIL 2025 – REVISED SEPTEMBER 2025 www.ti.com

18 Submit Document Feedback Copyright © 2025 Texas Instruments Incorporated

Product Folder Links: TPUL2T323

7 Detailed Description

7.1 Overview

The TPUL2T323 device contains two independent extended-pulse-width retriggerable monostable multivibrator circuits. A monostable multivibrator, also commonly known as a "one shot," produces a single digital pulse when triggered and otherwise maintains a constant output state. The TPUL2T323 device features three gated trigger inputs for each channel. For a rising edge trigger, the T or CLR input is used. For a falling edge trigger the T input is used. The TPUL2T323 device includes an asynchronous clear input ( CLR) that can be used to terminate an ongoing output pulse. When triggered, the TPUL2T323 outputs a positive digital pulse with pulse width defined as t wo = 1024 × K × R ext × C ext, with R ext and C ext being the external timing resistor and external timing capacitor component values measured in Ω and F, respectively, and K being a unitless nonlinearity correction factor provided in the Typical Characteristics section. The external timing components must be connected as shown in Figure 7-1. The external ground connection to the C terminal is optional. RC C VCC Rext Cext VCC GND RC C VCC Rext Cext VCC GND Figure 7-1. Timing component connection, with and without external ground

7.2 Functional Block Diagram

Vrefh = 0.69 × VCC Vrefl = 0.25 × VCC Cint indicates total internal parasitic capacitance and can be found in the Electrical Characteristics table. Control Logic Cint Vrefh VCC Vrefl T T CLR Q RC C Power-on Reset Q One of two channels TPUL2T323 SCASE79A – APRIL 2025 – REVISED SEPTEMBER 2025 www.ti.com

20 Submit Document Feedback Copyright © 2025 Texas Instruments Incorporated

Product Folder Links: TPUL2T323

7.3 Feature Description

7.3.1 Naming Convention

G : Standard T : Reduced Timing Type 1 : RC 1x, Retrig 2 : RC 1x, Non-retrig 3 : RC 1000x, Retrig Output(s) 0 : Active Low 1 : Active High 2 : Both Input(s) 0 : Falling edge (FE) 1 : Rising edge (RE) 2 : FE, RE, async clear 3 : FE, RE, async clear, and trigger on clear release Rating [none] : Commercial / Industrial -Q1 : Automotive, AEC-Q100 Figure 7-2. Device name meaning

7.3.2 Retriggerable One-Shot

This device includes a retriggerable monostable multivibrator (one-shot) circuit that produces a fixed-width output pulse. The output pulse width for a retriggerable one-shot is extended by additional input triggers while the output is active. The output pulse will expire after the configured time period if no other triggers have been received. The output pulse width after a retrigger event is always shorter than the normal output pulse width because the timing capacitor does not need to be fully discharged for a retrigger event. The maximum error due to this change is the time to discharge the selected timing capacitor. The error due to retrigger timing can be minimized by selecting larger resistor values and smaller capacitor values for a given pulse width. See retrigger plots in the Typical Characteristics section for more details.

7.3.3 Extended RC Timed One-Shot

The output pulse width (t wo) is controlled by the selection of external timing components R ext and C ext. The TPUL2T323 has been designed to target a typical output pulse width of t wo ≅ 1000 × R ext × C ext, however the actual pulse width changes with multiple variables, and thus a nonlinearity correction factor, K, is added to provide the system designer with a more accurate pulse width estimation. Equation 1 is used to most accurately predict the output pulse width. t wo = K × 1024 × R ext × C ext (1) The output pulse width is dependent on multiple variables:

• External timing components (Rext, Cext)
• Voltage
• Temperature
• Manufacturing and design
• Digital state machine operation The external timing component values directly control the output pulse width, and any variations in component values due to manufacturing, voltage, or temperature will directly impact the output pulse width. Most resistors maintain very consistent values during operation, and thus tend to have little impact on accuracy. Most capacitors have a wide variation of manufacturing values, and additionally can vary due to temperature and operating voltage. Typically, the timing capacitor is the largest single source of error for RC timed monostable multivibrators. There is also some error introduced by the TPUL2T323. This error is provided as Δtwo in the Switching Characteristics section and includes variations due to digital state machine operation, design, manufacturing, and temperature. There is additionally some randomness inherent to the pulse width even with all other factors held constant which is typically less than 1% and is accounted for in the Δtwo specification. www.ti.com TPUL2T323 SCASE79A – APRIL 2025 – REVISED SEPTEMBER 2025 Copyright © 2025 Texas Instruments Incorporated Submit Document Feedback 21 Product Folder Links: TPUL2T323

Estimating the percent error of the output pulse width (e Δtwo) requires multiple inputs. Equation 2 provides the best method to estimate total pulse width error due to tolerance of components, with e R being the error introduced by the timing resistor, e C being the error introduced by the timing capacitor, and Δtwo being the error introduced by the TPUL2T323. e Δ tw o = e R + e C + e R e C + Δ t w o 1 + e R + e C + e R e C (2) For a quick estimate, the sum of the error values can be used (e Δtwo ≅ e R + e C + Δ two). For example, a typical TPUL2T323 application circuit using an X7R capacitor (5% manufacturing tolerance + 15% temperature variation), 0.1% resistor, and Δtwo of 5% would have a quickly estimated maximum error of 25.1%. With the more accurate equation, the maximum error is actually 26.126%.

7.3.4 Balanced CMOS Push-Pull Outputs

This device includes balanced CMOS push-pull outputs. The term balanced indicates that the device can sink and source similar currents. The drive capability of this device may create fast edges into light loads, so routing and load conditions should be considered to prevent ringing. Additionally, the outputs of this device are capable of driving larger currents than the device can sustain without being damaged. It is important to limit the output power of the device to avoid damage due to overcurrent. The electrical and thermal limits defined in the Absolute Maximum Ratings must be followed at all times. Unused push-pull CMOS outputs must be left disconnected.

7.3.5 CMOS Schmitt-Trigger Inputs

This device includes inputs with the Schmitt-trigger architecture. These inputs are high impedance and are typically modeled as a resistor in parallel with the input capacitance given in the Electrical Characteristics table from the input to ground. The worst case resistance is calculated with the maximum input voltage, given in the Absolute Maximum Ratings table, and the maximum input leakage current, given in the Electrical Characteristics table, using Ohm's law (R = V ÷ I). The Schmitt-trigger input architecture provides hysteresis as defined by ΔVT in the Electrical Characteristics table, which makes this device extremely tolerant to slow or noisy inputs. While the inputs can be driven much slower than standard CMOS inputs, it is still recommended to properly terminate unused inputs. Driving the inputs with slow transitioning signals will increase dynamic current consumption of the device with the maximum value per input defined as ΔICC in the Electrical Characteristics table. For additional information regarding Schmitt-trigger inputs, please see Understanding Schmitt Triggers. Do not leave inputs floating at any time during operation. Unused inputs must be terminated at a valid high or low voltage level. If a system is not actively driving an input at all times, then a pull-up or pull-down resistor can be added to provide a valid input voltage during these times. The resistor value will depend on multiple factors; however, a 10kΩ resistor is recommended and will typically meet all requirements.

7.3.6 Latching Logic with Known Power-Up State

This device includes latching logic circuitry. Latching circuits commonly include D-type latches and D-type flip-flops, but include all logic circuits that act as volatile memory. In typical logic devices, the output state of each latching circuit is unknown after power is initially applied; however, this device includes an added Power On Reset (POR) circuit which sets the states of all included latching circuits during the power-up ramp prior to the device starting normal functionality. VPOR(min) VPOR(max) t VCC Figure 7-3. Supply (VCC) Ramp Characteristics for Known Power-Up State TPUL2T323 SCASE79A – APRIL 2025 – REVISED SEPTEMBER 2025 www.ti.com

22 Submit Document Feedback Copyright © 2025 Texas Instruments Incorporated

Product Folder Links: TPUL2T323

Figure 7-3 shows a correct supply voltage turn-on ramp and defines values used in the Recommended Operating Conditions and Electrical Characteristics tables. Prior to starting the power-on ramp, the supply must be completely off (VCC ≤ VPOR(min)). The supply voltage must ramp at a rate within the range provided in the Recommended Operating Conditions table. The output state of each latching logic circuit only remains stable as long as power is applied to the device (V CC ≥ VPOR(max)). Variation from these recommendations will result in the device having an unknown power-up state.

7.3.7 Partial Power Down (Ioff)

This device includes circuitry to disable all outputs when the supply pin is held at 0V. When disabled, the outputs will neither source nor sink current, regardless of the input voltages applied. The amount of leakage current at each output is defined by the Ioff specification in the Electrical Characteristics table.

7.3.8 Reduced Input Threshold Voltages

The TPUL2T323 was designed with reduced input voltage thresholds to support up-translation and inputs tolerant to 5.5V signal levels to support down-translation. For proper functionality, input signals must remain at or above the specified V T+(MAX) (VIH) level for a HIGH input state, and at or below the specified V T-(MIN) (VIL) for a LOW input state. Figure 7-4 shows the typical V IH and V IL levels for TPULxT devices, as well as the voltage levels for standard CMOS devices for comparison. Figure 7-4. TPULxT Input Voltage Levels www.ti.com TPUL2T323 SCASE79A – APRIL 2025 – REVISED SEPTEMBER 2025 Copyright © 2025 Texas Instruments Incorporated Submit Document Feedback 23 Product Folder Links: TPUL2T323

7.3.9 Clamp Diode Structure

Figure 7-5 shows the inputs and outputs to this device have negative clamping diodes only. CAUTION Voltages beyond the values specified in the Absolute Maximum Ratings table can cause damage to the device. The input and output voltage ratings may be exceeded if the input and output clamp- current ratings are observed. Figure 7-5. Electrical Placement of Clamping Diodes for Each Input and Output TPUL2T323 SCASE79A – APRIL 2025 – REVISED SEPTEMBER 2025 www.ti.com

24 Submit Document Feedback Copyright © 2025 Texas Instruments Incorporated

Product Folder Links: TPUL2T323

7.4 Device Functional Modes

7.4.1 Off-State Operation

The TPUL2T323 includes partial-power-down (I off) protection, which forces the outputs into a high-impedance state when the supply voltage is approximately 0V. In the powered-off state, voltages can be applied to the digital inputs and outputs and the device will not respond or have any back-powering. This protection does not apply to the RC pin.

7.4.2 Startup Operation

The TPUL2T323 includes an internal power-on reset (POR) circuit that prevents erroneous triggers from occurring during startup. There are details on the supply ramp requirements provided in Latching Logic with Known Power-Up State . Normal operation can be started after the startup time (t startup) has expired per the Timing Requirements table. While active, the POR circuit holds the TPUL2T323 in the Ready state.

7.4.3 On-State Operation

The table below lists the on-state functional modes for the TPUL2T323. Table 7-1. Function Table INPUTS(1) OUTPUTS(2) CLR T T Q Q L X X L H H H X L(3) H(3) H X L L(3) H(3) H L ↑ (4) (4) H ↓ H (4) (4) ↑ L H (1) H = high voltage level, L = low voltage level, X = don't care (2) L = driving low, H = driving high, = driving high for the defined pulse width time, = driving low for the defined pulse width time (3) These outputs are based on the assumption that the indicated steady-state conditions at the inputs have been set up long enough to complete any output pulse. (4) If an output pulse is triggered while a previous output pulse is still active, the output continues to drive high for one additional pulse width. www.ti.com TPUL2T323 SCASE79A – APRIL 2025 – REVISED SEPTEMBER 2025 Copyright © 2025 Texas Instruments Incorporated Submit Document Feedback 25 Product Folder Links: TPUL2T323

8 Application and Implementation

Information in the following applications sections is not part of the TI component specification, and TI does not warrant its accuracy or completeness. TI’s customers are responsible for determining suitability of components for their purposes, as well as validating and testing their design implementation to confirm system functionality.

8.1 Application Information

The TPUL2T323 is used to generate a fixed-width pulse from an input trigger event. This device is retriggerable, meaning that input triggers received while the output is active will cause the output pulse to extend and it will not expire until one configured time period after the most recent trigger. The input trigger event comes from three gated inputs: T, T, and CLR. These inputs are combined in a 3-input AND gate, with T internally inverted such that the logic follows the boolean equation Y = !( T) • T • CLR. Each input has a Schmitt-trigger architecture, and thus includes hysteresis allowing for slow transitioning or noisy signals. An input signal is detected as a logic high if the signal is larger than V T+, and a low if the input signal is smaller than V T-. Between V T+ and V T-, the input signal is detected as the last valid state until one of those values is crossed. An output pulse is triggered on the rising edge of the aforementioned internal Y signal. The output pulse width is controlled by the selection of external timing components R ext and C ext. Plots are provided in the Typical Characteristics section to easily select appropriate component values for a desired pulse width. See the Features section for additional information regarding the impact of external components on the timing accuracy of the TPUL2T323.

8.2 Typical Application - Edge Detector

In this application, the TPUL2T323 is used to detect rising or falling edges on an input signal, producing short pulses at the output for each edge detected. The circuit configuration for a rising edge detector is shown in Figure 8-1. For a falling edge detector, connect the input signal to the T input instead of the T input, and connect the T input to VCC. Otherwise, the components and configuration are identical. T T CLR Q One-Shot RC C GND Rext Cext VCC VCC VCC Ac ve-high output pulse VCC Q TRIG CLR Q Bypass Capacitor(s) Trigger signal Figure 8-1. Pulse Generator Schematic Using the TPUL2T323 TPUL2T323 SCASE79A – APRIL 2025 – REVISED SEPTEMBER 2025 www.ti.com

26 Submit Document Feedback Copyright © 2025 Texas Instruments Incorporated

Product Folder Links: TPUL2T323

8.2.1 Design Requirements

8.2.1.1 Timing Components

The external timing components directly determine the output pulse width of the TPUL2T323. The range of supported values for R ext and Cext are provided in the Recommended Operating Conditions table. Do not exceed the limits provided in the Absolute Maximum Ratings table. The TPUL2T323 can be used with no external capacitor, which is described as C ext = 0pF. In this condition, the output pulse width is determined by the operating voltage and external timing resistor, R ext, only. The expected variation is provided in the Switching Characteristics table for the case of Rext = 1MΩ, Cext = 0pF. If an external timing capacitor larger than 1µF is used, add an external Schottky diode (D ext) as shown in Figure 8-2 to provide an alternate discharge path for the capacitor during power down. RC C VCC Rext Cext VCC Dext GND Figure 8-2. External protection diode connection

8.2.1.2 Input Considerations

Input signals must cross to be considered a logic LOW, and to be considered a logic HIGH. Do not exceed the maximum input voltage range found in the Absolute Maximum Ratings. Unused inputs must be terminated to either V CC or ground. The unused inputs can be directly terminated if the input is completely unused, or they can be connected with a pull-up or pull-down resistor if the input will be used sometimes, but not always. A pull-up resistor is used for a default state of HIGH, and a pull-down resistor is used for a default state of LOW. The drive current of the controller, leakage current into the TPUL2T323 (as specified in the Electrical Characteristics ), and the desired input transition rate limits the resistor size. A 10k Ω resistor value is recommended for most applications. Refer to the Feature Description section for additional information regarding the inputs for this device. www.ti.com TPUL2T323 SCASE79A – APRIL 2025 – REVISED SEPTEMBER 2025 Copyright © 2025 Texas Instruments Incorporated Submit Document Feedback 27 Product Folder Links: TPUL2T323

8.2.1.3 Output Considerations

The positive supply voltage is used to produce the output HIGH-state voltage. Drawing current from the output decreases the output voltage as specified by the V OH specification in the Electrical Characteristics. The ground voltage is used to produce the output LOW-state voltage. Sinking current into the output increases the output voltage as specified by the VOL specification in the Electrical Characteristics. Push-pull outputs that could be in opposite states, even for a very short time period, should never be connected directly together to avoid excessive current and damage to the device. The TPUL2T323 can directly drive a load with a total capacitance less than or equal to 50pF while still meeting all of the data sheet specifications. For larger capacitive loads, add a series resistor to maintain current within the Absolute Maximum Ratings. The TPUL2T323 can drive a load with total resistance described by R L ≥ VO / I O, with the output voltage and current defined in the Electrical Characteristics table with VOH and VOL. When outputting in the HIGH state, the output voltage in the equation is defined as the difference between the measured output voltage and the supply voltage at the VCC pin. Unused outputs can be left floating. Do not connect outputs directly to VCC or ground. Refer to the Feature Description section for additional information regarding the outputs for this device.

8.2.1.4 Power Considerations

Ensure the desired supply voltage is within the range specified in the Recommended Operating Conditions . The supply voltage sets the electrical characteristics of the device as described in the Electrical Characteristics section. The ground must be capable of sinking current equal to the total current to be sunk by all outputs of the TPUL2T323 plus the maximum supply current, I CC, listed in the Electrical Characteristics , and any transient current required for switching. The logic device can only sink as much current that can be sunk into its ground connection. Ensure the maximum total current through GND listed in the Absolute Maximum Ratings is not exceeded. Thermal increase can be calculated using the information provided in Thermal Characteristics of Standard Linear and Logic (SLL) Packages and Devices. CAUTION The maximum junction temperature, TJ(max) listed in the Absolute Maximum Ratings, is an additional limitation to prevent damage to the device. Do not violate any values listed in the Absolute Maximum Ratings. These limits are provided to prevent damage to the device. TPUL2T323 SCASE79A – APRIL 2025 – REVISED SEPTEMBER 2025 www.ti.com

28 Submit Document Feedback Copyright © 2025 Texas Instruments Incorporated

Product Folder Links: TPUL2T323

8.2.2 Detailed Design Procedure

Texas Instruments provides an Excel-based calculator for getting the best results when using the TPUL2T323. This calculator can be found through the device's product folder, located in the Design and development section. The steps below are used for manually calculating the required timing component values using the information available in this document. 1. Select the desired output pulse width (two), and calculate two1 = two / 1024. 2. Solve: Cext1 = two1/50000. 3. Select the nearest decade capacitor value to Cext1 from the following and use for Cext. { 100pF, 1nF, 10nF, 100nF, 1µF, 10µF } 4. Solve: Rext1 = two1/Cext. 5. Using Rext1 from step 4 and Cext from step 3, find the closest K factor using the appropriate plot from the Typical Characteristics section. 6. Solve: Rext = two1/(K × Cext) 7. Connect the selected timing resistor, Rext, from RC to VCC. 8. Connect the selected timing capacitor, Cext, from RC (positive) to C (negative). The C pin can additionally be connected to ground, however it is not required for normal operation. 9. Add a 0.1µF bypass capacitor from VCC to GND. The capacitor needs to be placed physically close to the device and electrically close to both the VCC and GND pins. An example layout is shown in the Layout section. 10. Ensure the capacitive load at the output is ≤ 50pF. This is not a hard limit, however, it will optimize performance and prevent reliability issues. This can be accomplished by providing short, appropriately sized traces from the TPUL2T323 to any receiving devices. 11. Ensure the resistive load at the output is larger than (VCC / IO(max))Ω. Doing this will prevent the maximum output current from the Absolute Maximum Ratings from being violated. Most CMOS inputs have a resistive load measured in MΩ; much larger than the minimum calculated previously. 12. Thermal issues are rarely a concern for TPUL family devices, however, the power consumption and thermal increase can be calculated using the steps provided in the application report, CMOS Power Consumption and Cpd Calculation.

8.2.3 Application Curves

T Q two twotrr Figure 8-3. Output Pulse Timing Diagram www.ti.com TPUL2T323 SCASE79A – APRIL 2025 – REVISED SEPTEMBER 2025 Copyright © 2025 Texas Instruments Incorporated Submit Document Feedback 29 Product Folder Links: TPUL2T323

8.3 Typical Application - Delayed Pulse Generator

In this application, the TPUL2T323 is used to produce a delayed output pulse from a rising edge input trigger. The circuit configuration is shown in Figure 8-4. T T CLR Q One-Shot RC C Rext1 Cext1 VCC VCC Q TRIG CLR QTrigger signal T T CLR Q One-Shot RC C GND Rext2 Cext2 VCC VCC VCC Ac ve-high output pulse VCC Q TRIG CLR Q Bypass Capacitor(s) Channel 1 Channel 2 Figure 8-4. Delayed Pulse Generation Schematic Using the TPUL2T323

8.3.1 Application Curves

1Q, 2T two1 two1trr 2Q two2 two2 Figure 8-5. Output Pulse Timing Diagram

8.4 Power Supply Recommendations

The power supply can be any voltage between the minimum and maximum supply voltage rating listed in the Recommended Operating Conditions. During startup, the power supply should ramp within the provided power-up ramp rate range in the Recommended Operating Conditions table. Each VCC terminal must have a good bypass capacitor to prevent power disturbance. For normal operation of the TPUL2T323, a 0.1μF bypass capacitor is recommended. To reject different frequencies of noise, use multiple bypass capacitors in parallel. Capacitors with values of 0.1μF and 1μF are commonly used in parallel. TPUL2T323 SCASE79A – APRIL 2025 – REVISED SEPTEMBER 2025 www.ti.com

30 Submit Document Feedback Copyright © 2025 Texas Instruments Incorporated

Product Folder Links: TPUL2T323

8.5 Layout

8.5.1 Layout Guidelines

• Timing component placement – Place near the device – Provide an electrically short path to the device terminal connections
• Bypass capacitor placement – Place near the positive supply terminal of the device – Provide an electrically short ground return path – Use wide traces to minimize impedance – Keep the device, capacitors, and traces on the same side of the board whenever possible
• Signal trace geometry – 8mil to 12mil trace width – Lengths less than 12cm to minimize transmission line effects – Avoid 90° corners for signal traces – Use an unbroken ground plane below signal traces – Flood fill areas around signal traces with ground – For traces longer than 12cm
• Use impedance controlled traces
• Source-terminate using a series damping resistor near the output
• Avoid branches; buffer signals that must branch separately

8.5.2 Layout Example

0.1 F Bypass capacitor placed close to the device Recommend GND flood fill for improved signal isolation, noise reduction, and thermal dissipation GND 2T Cext1 Rext1 Cext2 Rext2 8 Unused input tied to GND Unused output left floating Unused inputs tied to VCC Avoid 90° corners for signal lines Figure 8-6. Layout Example for TPUL2T323 in the PW (TSSOP) package www.ti.com TPUL2T323 SCASE79A – APRIL 2025 – REVISED SEPTEMBER 2025 Copyright © 2025 Texas Instruments Incorporated Submit Document Feedback 31 Product Folder Links: TPUL2T323

9 Device and Documentation Support

TI offers an extensive line of development tools. Tools and software to evaluate the performance of the device, generate code, and develop solutions are listed below.

9.1 Documentation Support

9.1.1 Related Documentation

For related documentation, see the following:

• Texas Instruments, CMOS Power Consumption and Cpd Calculation application note
• Texas Instruments, Designing With Logic application note
• Texas Instruments, Thermal Characteristics of Standard Linear and Logic (SLL) Packages and Devices application note

9.2 Receiving Notification of Documentation Updates

To receive notification of documentation updates, navigate to the device product folder on ti.com. Click on Notifications to register and receive a weekly digest of any product information that has changed. For change details, review the revision history included in any revised document.

9.3 Support Resources

TI E2E™ support forums are an engineer's go-to source for fast, verified answers and design help — straight from the experts. Search existing answers or ask your own question to get the quick design help you need. Linked content is provided "AS IS" by the respective contributors. They do not constitute TI specifications and do not necessarily reflect TI's views; see TI's Terms of Use.

9.4 Trademarks

TI E2E™ is a trademark of Texas Instruments. All trademarks are the property of their respective owners.

9.5 Electrostatic Discharge Caution

This integrated circuit can be damaged by ESD. Texas Instruments recommends that all integrated circuits be handled with appropriate precautions. Failure to observe proper handling and installation procedures can cause damage. ESD damage can range from subtle performance degradation to complete device failure. Precision integrated circuits may be more susceptible to damage because very small parametric changes could cause the device not to meet its published specifications.

9.6 Glossary

TI Glossary This glossary lists and explains terms, acronyms, and definitions. NOTE: Page numbers for previous revisions may differ from page numbers in the current version. Changes from Revision * (April 2025) to Revision A (September 2025) Page

11 Mechanical, Packaging, and Orderable Information

The following pages include mechanical, packaging, and orderable information. This information is the most current data available for the designated devices. This data is subject to change without notice and revision of this document. For browser-based versions of this data sheet, refer to the left-hand navigation. TPUL2T323 SCASE79A – APRIL 2025 – REVISED SEPTEMBER 2025 www.ti.com

32 Submit Document Feedback Copyright © 2025 Texas Instruments Incorporated

Product Folder Links: TPUL2T323

www.ti.com 16-Oct-2025 PACKAGING INFORMATION Orderable part number Status (1) Material type (2) Package | Pins Package qty | Carrier RoHS (3) Lead finish/ Ball material (4) MSL rating/ Peak reflow (5) Op temp (°C) Part marking (6) PTPUL2T323PWR Active Preproduction TSSOP (PW) | 16 3000 | LARGE T&R - Call TI Call TI -40 to 125 PTPUL2T323PWR.A Active Preproduction TSSOP (PW) | 16 3000 | LARGE T&R - Call TI Call TI -40 to 125 TPUL2T323PWR Active Production TSSOP (PW) | 16 3000 | LARGE T&R Yes NIPDAU Level-1-260C-UNLIM -40 to 125 T2T323 (1) Status: For more details on status, see our product life cycle. (2) Material type: When designated, preproduction parts are prototypes/experimental devices, and are not yet approved or released for full production. Testing and final process, including without limitation quality assurance, reliability performance testing, and/or process qualification, may not yet be complete, and this item is subject to further changes or possible discontinuation. If available for ordering, purchases will be subject to an additional waiver at checkout, and are intended for early internal evaluation purposes only. These items are sold without warranties of any kind. (3) RoHS values: Yes, No, RoHS Exempt. See the TI RoHS Statement for additional information and value definition. (4) Lead finish/Ball material: Parts may have multiple material finish options. Finish options are separated by a vertical ruled line. Lead finish/Ball material values may wrap to two lines if the finish value exceeds the maximum column width. (5) MSL rating/Peak reflow: The moisture sensitivity level ratings and peak solder (reflow) temperatures. In the event that a part has multiple moisture sensitivity ratings, only the lowest level per JEDEC standards is shown. Refer to the shipping label for the actual reflow temperature that will be used to mount the part to the printed circuit board. (6) Part marking: There may be an additional marking, which relates to the logo, the lot trace code information, or the environmental category of the part. Multiple part markings will be inside parentheses. Only one part marking contained in parentheses and separated by a "~" will appear on a part. If a line is indented then it is a continuation of the previous line and the two combined represent the entire part marking for that device. Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals. TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release. In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis. OTHER QUALIFIED VERSIONS OF TPUL2T323 :

• Automotive : TPUL2T323-Q1 Addendum-Page 1

www.ti.com 16-Oct-2025 NOTE: Qualified Version Definitions:

• Automotive - Q100 devices qualified for high-reliability automotive applications targeting zero defects Addendum-Page 2

PACKAGE MATERIALS INFORMATION www.ti.com 17-Oct-2025 TAPE AND REEL INFORMATION Reel Width (W1) REEL DIMENSIONS A0B0K0WDimension designed to accommodate the component lengthDimension designed to accommodate the component thicknessOverall width of the carrier tapePitch between successive cavity centersDimension designed to accommodate the component width TAPE DIMENSIONSK0 P1B0WA0Cavity QUADRANT ASSIGNMENTS FOR PIN 1 ORIENTATION IN TAPE Pocket QuadrantsSprocket HolesQ1Q1Q2Q2Q3Q3Q4Q4User Direction of Feed P1ReelDiameter *All dimensions are nominal Device Package Type Package Drawing Pins SPQ Reel Diameter (mm) Reel Width W1 (mm) (mm) (mm) (mm) (mm) W (mm) Pin1 Quadrant Pack Materials-Page 1

PACKAGE MATERIALS INFORMATION www.ti.com 17-Oct-2025 TAPE AND REEL BOX DIMENSIONS Width (mm) W LH *All dimensions are nominal Device Package Type Package Drawing Pins SPQ Length (mm) Width (mm) Height (mm) TPUL2T323PWR TSSOP PW 16 3000 353.0 353.0 32.0 Pack Materials-Page 2

www.ti.com PACKAGE OUTLINE C 14X 0.65 4.55 16X 0.30 0.17 6.6

6.2 TYP

1.2 MAX

0.15 0.05 0.25 GAGE PLANE 0 -8 4X (0 -12 ) B 4.5 4.3 NOTE 4 A 5.1 4.9 NOTE 3 0.75 0.50 (0.15) TYP TSSOP - 1.2 mm max heightPW0016A SMALL OUTLINE PACKAGE 4220204/B 12/2023

0.1 C A B

0.1 C NOTES: 1. All linear dimensions are in millimeters. Any dimensions in parenthesis are for reference only. Dimensioning and tolerancing per ASME Y14.5M. 2. This drawing is subject to change without notice. 3. This dimension does not include mold flash, protrusions, or gate burrs. Mold flash, protrusions, or gate burrs shall not exceed 0.15 mm per side. 4. This dimension does not include interlead flash. Interlead flash shall not exceed 0.25 mm per side. 5. Reference JEDEC registration MO-153. SEATING PLANE A 20 DETAIL A TYPICAL SCALE 2.500

www.ti.com EXAMPLE BOARD LAYOUT

0.05 MAX

0.05 MIN

16X (1.5) 16X (0.45) 14X (0.65) (5.8) (R0.05) TYP TSSOP - 1.2 mm max heightPW0016A SMALL OUTLINE PACKAGE 4220204/B 12/2023 NOTES: (continued) 6. Publication IPC-7351 may have alternate designs. 7. Solder mask tolerances between and around signal pads can vary based on board fabrication site. LAND PATTERN EXAMPLE EXPOSED METAL SHOWN SCALE: 10X SYMM SYMM 8 9 15.000 METALSOLDER MASK OPENING METAL UNDER SOLDER MASK SOLDER MASK OPENING EXPOSED METALEXPOSED METAL SOLDER MASK DETAILS NON-SOLDER MASK DEFINED (PREFERRED) SOLDER MASK DEFINED

www.ti.com EXAMPLE STENCIL DESIGN 16X (1.5) 16X (0.45) 14X (0.65) (5.8) (R0.05) TYP TSSOP - 1.2 mm max heightPW0016A SMALL OUTLINE PACKAGE 4220204/B 12/2023 NOTES: (continued) 8. Laser cutting apertures with trapezoidal walls and rounded corners may offer better paste release. IPC-7525 may have alternate design recommendations. 9. Board assembly site may have different recommendations for stencil design. SOLDER PASTE EXAMPLE BASED ON 0.125 mm THICK STENCIL SCALE: 10X SYMM SYMM 8 9

IMPORTANT NOTICE AND DISCLAIMER TI PROVIDES TECHNICAL AND RELIABILITY DATA (INCLUDING DATASHEETS), DESIGN RESOURCES (INCLUDING REFERENCE DESIGNS), APPLICATION OR OTHER DESIGN ADVICE, WEB TOOLS, SAFETY INFORMATION, AND OTHER RESOURCES “AS IS” AND WITH ALL FAULTS, AND DISCLAIMS ALL WARRANTIES, EXPRESS AND IMPLIED, INCLUDING WITHOUT LIMITATION ANY IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE OR NON-INFRINGEMENT OF THIRD PARTY INTELLECTUAL PROPERTY RIGHTS. These resources are intended for skilled developers designing with TI products. You are solely responsible for (1) selecting the appropriate TI products for your application, (2) designing, validating and testing your application, and (3) ensuring your application meets applicable standards, and any other safety, security, regulatory or other requirements. These resources are subject to change without notice. TI grants you permission to use these resources only for development of an application that uses the TI products described in the resource. Other reproduction and display of these resources is prohibited. No license is granted to any other TI intellectual property right or to any third party intellectual property right. TI disclaims responsibility for, and you fully indemnify TI and its representatives against any claims, damages, costs, losses, and liabilities arising out of your use of these resources. TI’s products are provided subject to TI’s Terms of Sale, TI’s General Quality Guidelines, or other applicable terms available either on ti.com or provided in conjunction with such TI products. TI’s provision of these resources does not expand or otherwise alter TI’s applicable warranties or warranty disclaimers for TI products. Unless TI explicitly designates a product as custom or customer-specified, TI products are standard, catalog, general purpose devices. TI objects to and rejects any additional or different terms you may propose. IMPORTANT NOTICE Copyright © 2025, Texas Instruments Incorporated Last updated 10/2025