DATASHEET SEARCH SITE | WWW.ALLDATASHEET.COM

Document overview

  • Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
  • PDF pages: 16

Technical content

Features

  • Fully Functional SWIFT Module
  • Single-Device: 5 V/3.3 V Input
  • DSP Compatible
  • No Output Capacitors Required
  • High Efficiency (93 % at 4 A)
  • Small Footprint (0.355 in², Suffix ‘N’)
  • Adjustable Output Voltage Pin-Out Information C 1 (Re quired) C 2 (Optional) +V O GNDGND +V IN PT54002 INH V O ADJ * For Inhibit pin: Open = output enabled Ground = output disabled

Description

The PT5400 Excalibur™ power modules are a series of high-performance integrated switching regulators (ISRs) based on TI’s SWIFT (Switcher With Integrated FET Technology) regulator ICs. These ready-to-use modules are rated for up to

6 A of output current from input voltages as low

as 3.1 V, providing a convenient step-down power source for the industry’s latest high-performance DSPs and microprocessors. The series includes output voltage options as low as 1.0 VDC. The PT5400 modules are packaged in a 5-pin thermally efficient copper case, which offers the advantage of solderability along with a small foot- print (0.355 in², suffix ‘N’). Both through-hole and surface mount pin configurations are available. The product features external output voltage adjustment, an on/off inhibit function, short cir- cuit protection, and thermal shutdown. A 100-µF input capacitor is required for proper operation. PT Series Suffix (PT1234x) Case/Pin Order Package Configuration Suffix Code Vertical N (EFK) Horizontal A (EFL) SMD C (EFM) (Reference the applicable package code draw- ing for the dimensions and PC board layout)

  • On/Off Inhibit Function
  • Short Circuit Protection
  • Thermal Shutdown
  • Space-Saving package
  • Solderable Copper Case

For technical support and further information, visit http://power.ti.com Environmental Specifications PT5400 Series Characteristics Symbols Conditions Min Typ Max Units Operating Temperature Range T a Over Vin range –40 (i) —8 5° C Over-T emperature Shutdown OTP internal junction temp, auto-reset — 150 — °C Storage Temperature T s — –40 — 125 °C Solder Reflow Temperature T reflow Measured on any part of module — — 215 (ii) °C Mechanical Shock Mil-STD-883D, Method 2002.3 — 500 — G’s Half Sine, mounted to a fixture Mechanical Vibration Mil-STD-883D, Method 2007.2, Vertical 20-2000 Hz, PCB mounted Horizontal — 20 (iii) —G ’ s Weight — — — 6.5 — grams Flammability — Materials meet UL 94V-0 Notes: (i) For operation below 0 °C the external capacitors must have stable characteristics. Use either a low ESR tantalum or Oscon® c apacitor. (ii) During solder reflow of SMD package version, do not elevate the case, pin, or internal component temperatures above the sta ted maximum. For further guidance refer to the application note, “Reflow Soldering Requirements for Plug-in Power Surface Mount Products,” (SLTA051). (iii) The case pins on the through-hole package types (suffixes N & A) must be soldered. For more information see the applicable package outline drawing. PT5400 Series 6-A 5-V/3.3-V Input Adjustable SWIFT™ Power Module SL TS169C - MAY 2002 - REVISED OCTOBER 2003 Unless otherwise stated, T a =25 °C, Vin =5 V, C1 =100 µF, C2 =0 µF, and Io =Iomax PT5400 Series (Except PT5408) Characteristics Symbols Conditions Min Typ Max Units Output Current I o Vin =5 V 0 — 6 (1) AVin =3.3 V 0 — 5.5 (1) Input Voltage Range V in Over Io range V o ≥ 2.5 V 4.5 — 5.5 V Vo ≤ 2.0 V 3.1 5.5 Set-Point Voltage Tolerance V o tol — — ±2 %V o Temperature Variation ∆Regtemp –40 °C <Ta < +85 °C — ±0.5 — %V o Line Regulation ∆Regline Over Vin range — ±5 — mV Load Regulation ∆Regload Over Io range — ±10 — mV Total Output Variation ∆Regtot Includes set-point, line, load, ——± 3% V o–40 °C ≤ Ta ≤ +85 °C Efficiency η Vin =5 V, Io =4 A PT5401 (3.3 V) — 93 — PT5402 (2.5 V) — 91 — PT5403 (2.0 V) — 88 — PT5405 (1.5 V) — 85 — PT5406 (1.2 V) — 82 — PT5407 (1.0 V) — 80 — Vin =3.3 V, Io =4 A PT5403 (2.0 V) — 88 — PT5404 (1.8 V) — 86 — PT5405 (1.5 V) — 84 — PT5407 (1.0 V) — 78 Vo Ripple (pk-pk) V r 20 MHz bandwidth — 15 — mVpp Transient Response 1 A/µs load step, 50 to 100 % I omax, C2 =100 µF ttr Recovery time — 50 — µSec ∆Vtr Vo over/undershoot — 50 — mV Current Limit Threshold I lim ∆Vo = –50 mV — 12 — A Output Voltage Adjust V o adj — ±10 — % Switching Frequency ƒ s Over Vin and Io ranges — 700 — kHz Under-Voltage Lockout UVLO V in increasing — 2.95 — VVin decreasing — 2.8 — Inhibit Control (pin1) Referenced to GND (pin3) Input High Voltage V IH Vin –0.5 — Open (2) V Input Low Voltage VIL –0.2 — 0.8 Input Low Current IIL Pin 1 to GND — –10 — µA Standby Input Current I in standby pins 1 & 3 connected — 1 — mA External Input Capacitance C 1 100 (3) ——µ F External Output Capacitance C 2 0 100 (4) 1,000 µF Reliability MTBF Per Bellcore TR-332 4 8——1 0 6 Hrs50 % stress, Ta =40 °C, ground benign Notes: (1) See SOA curves or consult factory for the appropriate derating. (2) The Inhibit control (pin 1) has an internal pull-up, and if left open-circuit the module will operate when input power is ap plied. A small low-leakage (<100 nA) MOSFET is recommended to control this input. See application notes for more information. (3) The regulator requires a minimum of 100 µF input capacitor with a minimum 300 mArms ripple current rating. For further infor mation, consult the related application note on Capacitor Recommendations. (4) An external output capacitor is not required for basic operation. Adding 100 µF of distributed capacitance at the load will improve the transient response.

For technical support and further information, visit http://power.ti.com Note A: Characteristic data has been developed from actual products tested at 25 °C. This data is considered typical data for the ISR. Note B: SOA curves represent operating conditions at which internal components are at or below manufacturer’s maximum rated operating t emperatures. Efficiency vs Output CurrentEfficiency vs Output Current Power Dissipation vs Output Current Power Dissipation vs Output Current Performance Data; Vin =5 V (See Note A) Performance Data; Vin =3.3 V (See Note A) PT5400 Series 6-A 5-V/3.3-V Input Adjustable SWIFT™ Power Module Typical Characteristics 100 0123456 Iout (A ) Efficiency - % PT5401 PT5402 PT5403 PT5404 PT5405 PT5406 PT5407 0123456 Iout (A ) Ripple - mV PT5403 PT5404 PT5405 PT5401 PT5406 PT5407 PT5402 Output Ripple vs Output Current Output Ripple vs Output Current 0123456 Iout (A ) Ambient Temperature (°C) 200LFM 120LFM 60LFM Nat conv Airflow Safe Operating Curve, Vin =5 V (See Note B) Safe Operating Curve, V in =3.3 V (See Note B) 0.0 0.5 1.0 1.5 2.0 2.5 0123456 Iout (A ) Pd - Watts 100 012345 Iout (A ) Efficiency - % PT5403 PT5404 PT5405 PT5406 PT5407 012345 Iout (A ) Ripple - mV PT5405 PT5403 PT5404 PT5406 PT5407 0.0 0.5 1.0 1.5 2.0 2.5 012345 Iout (A ) Pd - Watts 012345 Iout (A ) Ambient Temperature (°C) 200LFM 120LFM 60LFM Nat conv Airflow Typical Characteristics (Except PT5408) SLTS169C - MA Y 2002 - REVISED OCTOBER 2003

For technical support and further information, visit http://power.ti.com PT5408 6-A 5-V/3.3-V Input Adjustable SWIFT™ Power Module SL TS169C - MAY 2002 - REVISED OCTOBER 2003 Unless otherwise stated, T a =25 °C, Vin =3.3 V, C1 =100 µF, C2 =0 µF, and Io =Iomax PT5408 Characteristics Symbols Conditions Min Typ Max Units Output Current I o Vin =3.3 V 0 — 6 (1) Input Voltage Range V in Over Io range 3.1 3.6 Set-Point Voltage Tolerance V o tol — — ±2 %V o Temperature Variation ∆Regtemp –40 °C <Ta < +85 °C — ±0.5 — %V o Line Regulation ∆Regline Over Vin range — ±5 — mV Load Regulation ∆Regload Over Io range — ±10 — mV Total Output Variation ∆Regtot Includes set-point, line, load, ——± 3% V o–40 °C ≤ Ta ≤ +85 °C Efficiency η Io =4 A — 92 Vo Ripple (pk-pk) V r 20 MHz bandwidth — 15 — mVpp Transient Response 1 A/µs load step, 50 to 100 % I omax, C2 =100 µF ttr Recovery time — 50 — µSec ∆Vtr Vo over/undershoot — 50 — mV Current Limit Threshold I lim ∆Vo = –50 mV — 13 — A Output Voltage Adjust V o adj — ±10 — % Switching Frequency ƒ s Over Vin and Io ranges — 700 — kHz Under-Voltage Lockout UVLO V in increasing — 2.95 — VVin decreasing — 2.8 — Inhibit Control (pin1) Referenced to GND (pin3) Input High Voltage V IH Vin –0.5 — Open (2) V Input Low Voltage VIL –0.2 — 0.8 Input Low Current IIL Pin 1 to GND — –10 — µA Standby Input Current I in standby pins 1 & 3 connected — 1 — mA External Input Capacitance C 1 100 (3) ——µ F External Output Capacitance C 2 0 100 (4) 1,000 µF Reliability MTBF Per Bellcore TR-332 4 8——1 0 6 Hrs50 % stress, Ta =40 °C, ground benign Notes: (1) See SOA curves or consult factory for the appropriate derating. (2) The Inhibit control (pin 1) has an internal pull-up, and if left open-circuit the module will operate when input power is ap plied. A small low-leakage (<100 nA) MOSFET is recommended to control this input. See application notes for more information. (3) The regulator requires a minimum of 100 µF input capacitor with a minimum 300 mArms ripple current rating. For further infor mation, consult the related application note on Capacitor Recommendations. (4) An external output capacitor is not required for basic operation. Adding 100 µF of distributed capacitance at the load will improve the transient response.

For technical support and further information, visit http://power.ti.com Typical Characteristics (PT5408 only) Efficiency vs Output Current, V in =3.3 V (See Note A) Output Ripple vs Output Current (See Note A) Power Dissipation vs Output Current (See Note A) Safe Operating Curve, V in =3.3 V (See Note B) 100 0123456 Iout (A ) Efficiency - % 0123456 Iout (A ) Ripple - mV 0.4 0.8 1.2 1.6 0123456 Iout (A ) Pd - Watts Note A: Characteristic data has been developed from actual products tested at 25 °C. This data is considered typical data for the ISR. Note B: SOA curves represent operating conditions at which internal components are at or below manufacturer’s maximum rated operating t emperatures. 0123456 Iout (A) Ambient Temperature (°C) 200LFM 120LFM 60LFM Nat conv Airflow PT5408 6-A 5-V/3.3-V Input Adjustable SWIFT™ Power Module SLTS169C - MA Y 2002 - REVISED OCTOBER 2003 Typical Characteristics

For technical support and further information, visit http://power.ti.com PT5400 Series Operating Features of the PT5400 SWIFT™ Series of Power Modules Under-Voltage Lockout (UVLO) The PT5400 SWIFT series of power modules incor- porate an under-voltage lockout (UVLO) function. The UVLO function provides a clean transition during power- up and power-down, allowing the regulator to tolerate a slowly rising input voltage. The UVLO prevents opera- tion of the module until the input voltage has risen above 2.95 V. Below this threshold the status of the inhibit control pin is overriden, and the module will not produce an output. When the input voltage rises above this thresh- old, the output status of the module is determined by the inhibit control pin. If the inhibit control is open-circuit (not grounded), the module will automatically power up. The UVLO circuit has approximately 0.16 V of hysteresis, and will completely turn off the module when a falling input voltage drops below about 2.8 V. (Note: Even though the applied input voltage may be above the UVLO threshold, operation to the published specifications requires that the input voltage be at or above the minimum specified for each model in the series. This ensures that the output voltage of the module is in regulation.) Soft-Start Power Up Following either the application of a valid input source voltage, or the removal of a ground signal to the inhibit control pin (with input power applied), the module will initiate a soft-start power up. The soft start has two effects on the start-up characteristic. It introduces a short time delay prior to the start-up of the output voltage, and also slows the rate at which the output voltage rises. Figure 1-1 shows the power-up characteristic of a PT5404 (1.8 V). In this example the delay time, t d, is measured from the point at which the input voltage rises above

2.95 V (the UVLO threshold), to the point that the output

voltage starts to rise. The time period t (SS) is the rise time of the output voltage ramp. The value of t d and t (SS) are are approximately 10 ms and 7.5 ms respectively. Vin (1V/Div) Vout (1V/Div) t(SS)dt Vin =2.95V HORIZ SCALE: 5ms/Div Figure 1-1; Soft-Start Characteristic and Timing If desired, both time periods can be lengthened with the addition of a low value capacitor between the Inhibit control (pin 1) and the COM (pin 3). For a given value of external capacitance, C inh, the formulas for calculating the approximate effect on t d and t(SS) are given below. td ≈ (Cinh + 0.047 µF) × 1.2 V 5 µA t(SS) ≈ (Cinh + 0.047 µF) × 0.7 V 5 µA Note: The capacitor should be placed as close to the regulator as possible. Adding 0.047 µF of external capacitance to the Inhibit pin approximately doubles the value of t d and t(SS). Current Limit Protection The output current limit feature is one of two fault protection mechanisms built into the PT5400 modules. Its purpose is to protect both the module and input source against the occurance of a load fault, thereby isolating the fault and preventing it from propagating to other parts of the power system. The PT5400 regulators sense the current switched by the series (high-side) power MOSFET. The circuit implements a continuous current limit char- acteristic. Upon the removal of the fault the output voltage will promptly recover, and the module will return to nor- mal operation. A current limit condition will also increase the module’s power dissipation, which may cause the temperature of the internal components to significantly rise. If the con- dition persists, the module may begin to cycle in and out of thermal shutdown. Thermal Shutdown Thermal shutdown is the second fault protection mecha- nism and protects the module’s internal circuitry against excessively high temperatures. A rise in the temperature of the internal circuitry may be the result of a drop in airflow, a high ambient temperature, or a sustained over- current load fault. If the junction temperature of the internal components exceed 150 °C, the module will shutdown. Once in thermal shutdown, the regulator is disabled and the output voltage is reduced to zero. The recovery is automatic and begins with a soft-start power up. Recovery occurs when the the sensed temperature decreases 10 °C below the trip point. Application Notes

For technical support and further information, visit http://power.ti.com /rodneVroticapaC tnenopmoC seireS scitsiretcarahCroticapaCy titnauQ gnikroW egatloV) Fµ(eulaV tnelaviuqE)RSE( ecnatsiseRseireS elppiRxaM C°58ta )smrI(tnerruC eziSlacisyhP )mm( tupnI suB tuptuO suB rebmuNrodneV )TMS(AWcinosanaPV 01F µ0215 30.0 Ω Am00823 .8 × 9.61 1 P 121A1AWFEE CFcinosanaP )TMS(KF V61 V61 022F µ 033F µ 051.0 Ω 061.0 Ω Am555 Am006 01 × 2.01 8× 2.01 122C1CFUEE P133C1KFVEE noC–imehCdetinU SF )TMS(AXP )TMS(ZVM SP V01 V01 V61 V01 Fµ001 021F µ 022F µ Fµ072 040.0 Ω 720.0 Ω 071.0 Ω 410.0 Ω Am0012 Am0342 Am054 Am0244 3.6 × 8.9 8× 7.6 8× 01 8× 5.11 M001SF01 PT08HM121CV01AXP PT01HM122CV52ZVM 11HM072SP01 -TMS)55F(nocihciN )TMS(GW MP V01 V53 V52 Fµ001 001F µ 051F µ 550.0 Ω 051.0 Ω 061.0 Ω Am0002 Am076 Am064 3,4x3,7 01 × 01 01 × 5.11 NM101A155F SG1RNM101V1GWU HPM151E1MPU ®noc-sOoynaS )TMS(PVS PS APT V01 V61 V01 021F µ Fµ001 µ001F 040.0 Ω 520.0 Ω 080.0 Ω Am0052> Am0082> Am0021> 7×8 3.6 × 8.9 3.7 × 8.4 M021PVS01 M001SPS61 M001APT01 SPTmulatnaTXVAV 01 V01 Fµ001 Fµ022 01.00 Ω 001.0 Ω Am0901> Am4141> L3.7 × W3.4 × H1.4 0010R010M701DSPT 0010R010M722VSPT temeK0 25T 594T V01 V01 Fµ001 Fµ001 080.0 Ω 001.0 Ω Am0021 Am0011> L3.7 × W7.5 × H0.4 SA010M701D025T SA010M701X594T D595/D495eugarpSV 01 V01 Fµ051 Fµ021 090.0 Ω 041.0 Ω Am0011 Am0001> L3.7 × W0.6 × H1.4 T2C0100X751D495 T2D0100X721D595 R5XcimareC-KDT R5XcimareCataruM esaC0121 V3.6 V3.6 Fµ74 Fµ74 200.0 Ω 200.0 Ω Am0041> Am0001> L6.3 × W8.2 × H8.2 )xam(2 )xam(2 TM/TK674J0R5X5223C 3.6/M674J06RE23MRG PT5400 Series Capacitor Recommendations for the PT5400 SWIFT™ Series of Power Modules Input Capacitors The recommended input capacitance is determined by 100 µF minimum capacitance, 300 mA (rms) minimum ripple current rating, and less than 300 m Ω equivalent series resistance (ESR). The ripple current rating, ESR, and operating temperature are the major considerations when selecting the input capacitor. It is recommended that tantalum capacitors have a mini- mum voltage rating of at least twice the working voltage, including the ac ripple. This is necessary to insure reli- ability with 3.3-V input voltage bus applications. Output Capacitors (optional) The ESR of the output bulk (non-ceramic) capacitance must be between 10 m Ω ≤ESR ≤200 mΩ . Electrolytic capacitors have poor ripple performance at frequen- cies greater than 400 kHz but excellent low frequency transient response. Above the ripple frequency, ceramic decoupling capacitors are recommended to improve the transient response and reduce any high frequency noise components apparent during higher current excursions. A maximum of 100 µF ceramic capacitance may be added to the output bus. Tantalum/ Ceramic Capacitors Tantalum capacitors are acceptable on the output bus. Tantalum, Os-con®, or ceramic capacitor types are rec- ommended for applications where ambient temperatures fall below 0 °C. Ceramic capacitors may be used instead of electrolytic types on both the input and output bus. The input bus must have at least the minimum amount of capacitance. For the output bus the total amount of ceramic capacitance should be limited to 100 µF. Capacitor Tables Table 2-1 identifies vendors with acceptable ESR and maximum allowable ripple current (rms) ratings. Capaci- tors recommended for the output are identified under the Output Bus column with the required quantity. This is not an extensive capacitor list. Capacitors from other vendors are available with comparable specifications. Those listed are for guidance. The RMS ripple current rating and ESR (at 100 kHz) are critical parameters necessary to insure both optimum regulator performance and long capacitor life. Table 2-1; Recommended Input/Output Capacitors

For technical support and further information, visit http://power.ti.com PT5400 Series Adjusting the Output Voltage of the PT5400 Series of 6-A SWIFT Power Modules The output voltage of the PT5400 series of SWIFT power modules may be adjusted higher or lower than the factory trimmed pre-set voltage with the addition of a single external resistor. Table 4-1 gives the allowable adjustment range for each model of the series as V a (min) and Va (max). Adjust Up: An increase in the output voltage is obtained by adding a resistor R2, between pin 5 (Vo adj) and pin 3 (GND). Adjust Down: Add a resistor (R1), between pin 5 (Vo adj) and pin 4 (Vout). Figure 4-1 The values of (R1) [adjust down], and R 2 [adjust up], can either be calculated using the following formulas, or may be looked up from the range of values in Table 4-2. Refer to Figure 4-1 for the pla cement of the required resistor; either (R 1) or R2 as appropriate. (R1) = Ro (Va – 0.891) – 18.2 k Ω Vo – Va R2 = 0.891 Ro – 18.2 k Ω Va – Vo Where: V o = Original output voltage Va = Adjusted output voltage Ro = The resistance value from Table 4-1 Table 4-1 ISR OUTPUT VOLTAGE ADJUSTMENT RANGE AND FORMULA PARAMETERS Series Pt. No. PT5401 PT5402 PT5408 PT5403 PT5404 PT5405 PT5406 PT5407 Ad just Up 100 µF (Re q'd) +V O COMCOM +V IN (R1 ) Ad j Down PT54002 4Vin Vo Vo (ad j)GND Notes: 1. Use a 1% (or better) tolerance resistor in either the (R1) or R2 location. Place the resistor as close to the ISR as possible. 2. Never connect capacitors from Vo adj to either GND or Vout. Any capacitance added to the Vo adjust pin will affect the stability of the ISR. 3. For each model, adjustments to the output voltage may place additional limits on the minimum input voltage. The revised minimum input voltage must comply with the following requirement. V in(min) = (Va + 1.1) V or as specified in the data sheet, whichever is greater. 4. The PT5408 operates only from a 3.3-V input bus. The limited input to output voltage differential of this model does not allow it to be adjusted higher than its trimmed output voltage.

Application Notes continued For technical support and further information, visit http://power.ti.com ISR ADJUSTMENT RESISTOR VALUES Series Pt. No. PT5401 PT5402/8 PT5403 PT5404 PT5405 PT5406 PT5407 Va (req.d) 0.97 (8.7) kΩ 1.0 1.05 164.0 kΩ 1.1 (2.2) kΩ 72.7 kΩ 1.15 (32.4) kΩ 42.4 kΩ 1.2 27.2 kΩ 1.25 156.0 kΩ 18.2 kΩ 1.3 (2.7) kΩ 68.8 kΩ 12.1 kΩ 1.35 (13.0) kΩ 39.8 kΩ 7.8 kΩ 1.4 (33.7) kΩ 25.3 kΩ 4.5 kΩ 1.45 (95.8) kΩ 16.6 kΩ 2.0 kΩ 1.5 (2.1) kΩ 10.8 kΩ 1.55 (8.2) kΩ 164.0 kΩ 6.7 kΩ 1.6 (17.3) kΩ 72.7 kΩ 3.5 kΩ 1.75 (16.2) kΩ (154.0) kΩ 18.2 kΩ 1.8 (27.3) kΩ 12.1 kΩ 1.85 (45.7) kΩ 160.0 kΩ 7.8 kΩ 1.9 (82.7) kΩ 70.9 kΩ 4.5 kΩ 1.95 (194.0) kΩ 41.2 kΩ 2.0 kΩ 2.0 (4.4) kΩ 26.4 kΩ 2.1 (12.6) kΩ 70.9 kΩ 11.5 kΩ 2.15 (18.5) kΩ 41.2 kΩ 7.3 kΩ 2.2 (26.3) kΩ 26.4 kΩ 4.1 kΩ 2.25 (37.2) kΩ 17.4 kΩ 1.6 kΩ 2.3 (53.7) kΩ 11.5 kΩ 2.35 (81.0) kΩ 7.3 kΩ 2.4 (136.0) kΩ 4.1 kΩ 2.45 (300.0) kΩ 1.6 kΩ 2.5 2.55 ( Note 4) 164.0 k Ω 2.6 72.7 k Ω 2.65 42.4 k Ω 2.7 27.2 k Ω 2.75 18.2 k Ω 2.8 12.1 k Ω 2.85 7.8 k Ω 2.9 (33.0) kΩ 4.5 kΩ 2.95 (41.8) kΩ 2.0 kΩ 3.0 (53.5) kΩ 3.05 (69.9) kΩ 3.1 (94.5) kΩ 3.15 (135.0) kΩ 3.2 (217.0) kΩ 3.25 (463.0) kΩ 3.3 3.35 164.0 k Ω 3.4 72.7 k Ω 3.45 42.4 k Ω 3.48 32.3 k Ω 3.50 27.2 k Ω R1 = (Blue) R2 = Black Table 4-2 PT5400 Series

www.ti.com 15-Jan-2013 Addendum-Page 1 PACKAGING INFORMATION Orderable Device Status (1) Package Type Package Drawing Pins Package Qty Eco Plan (2) Lead/Ball Finish MSL Peak Temp (3) Samples (Requires Login) PT5401A LIFEBUY SIP MODULE EFL 5 30 Pb-Free (RoHS) Call TI N / A for Pkg Type PT5401C LIFEBUY SIP MODULE EFM 5 30 Pb-Free (RoHS) Call TI Level-3-215C-168HRS PT5401N LIFEBUY SIP MODULE EFK 5 30 Pb-Free (RoHS) Call TI N / A for Pkg Type PT5402A LIFEBUY SIP MODULE EFL 5 30 Pb-Free (RoHS) Call TI N / A for Pkg Type PT5402C LIFEBUY SIP MODULE EFM 5 30 Pb-Free (RoHS) Call TI Level-3-215C-168HRS PT5402N LIFEBUY SIP MODULE EFK 5 30 Pb-Free (RoHS) Call TI N / A for Pkg Type PT5403A OBSOLETE SIP MODULE EFL 5 TBD Call TI Call TI PT5403C OBSOLETE SIP MODULE EFM 5 TBD Call TI Call TI PT5404A LIFEBUY SIP MODULE EFL 5 30 Pb-Free (RoHS) Call TI N / A for Pkg Type PT5404C LIFEBUY SIP MODULE EFM 5 30 Pb-Free (RoHS) Call TI Level-3-215C-168HRS PT5404N LIFEBUY SIP MODULE EFK 5 30 Pb-Free (RoHS) Call TI N / A for Pkg Type PT5405A LIFEBUY SIP MODULE EFL 5 30 Pb-Free (RoHS) Call TI N / A for Pkg Type PT5405C LIFEBUY SIP MODULE EFM 5 30 Pb-Free (RoHS) Call TI Level-3-215C-168HRS PT5405N LIFEBUY SIP MODULE EFK 5 30 Pb-Free (RoHS) Call TI N / A for Pkg Type PT5406A LIFEBUY SIP MODULE EFL 5 30 Pb-Free (RoHS) Call TI N / A for Pkg Type PT5406C LIFEBUY SIP MODULE EFM 5 30 Pb-Free (RoHS) Call TI Level-3-215C-168HRS PT5406N LIFEBUY SIP MODULE EFK 5 30 Pb-Free (RoHS) Call TI N / A for Pkg Type PT5407A LIFEBUY SIP MODULE EFL 5 30 Pb-Free (RoHS) Call TI N / A for Pkg Type

www.ti.com 15-Jan-2013 Addendum-Page 2 Orderable Device Status (1) Package Type Package Drawing Pins Package Qty Eco Plan (2) Lead/Ball Finish MSL Peak Temp (3) Samples (Requires Login) PT5407C LIFEBUY SIP MODULE EFM 5 30 Pb-Free (RoHS) Call TI Level-3-215C-168HRS PT5408A LIFEBUY SIP MODULE EFL 5 30 Pb-Free (RoHS) Call TI N / A for Pkg Type PT5408C LIFEBUY SIP MODULE EFM 5 30 Pb-Free (RoHS) Call TI Level-3-215C-168HRS PT5408N LIFEBUY SIP MODULE EFK 5 30 Pb-Free (RoHS) Call TI N / A for Pkg Type (1) The marketing status values are defined as follows: ACTIVE: Product device recommended for new designs. LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect. NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design. PREVIEW: Device has been announced but is not in production. Samples may or may not be available. OBSOLETE: TI has discontinued the production of the device. (2) Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check http://www.ti.com/productcontent for the latest availability information and additional product content details. TBD: The Pb-Free/Green conversion plan has not been defined. Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements for all 6 substances, including the requirement that lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes. Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and package, or 2) lead-based die adhesive used between the die and leadframe. The component is otherwise considered Pb-Free (RoHS compatible) as defined above. Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame retardants (Br or Sb do not exceed 0.1% by weight in homogeneous material) (3) MSL, Peak Temp. -- The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature. Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals. TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release. In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis.

MMSI001 – SEPTEMBER 2001 1POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 EFL (R–MSIP–T5) METAL SINGLE-IN-LINE MODULE NOTES: A. All linear dimensions are in inches (mm). B. This drawing is subject to change without notice. E. Recommended mechanical keep-out area. F. Electrical pin length mounted on circuit board seating plane to pin end. G. Electrically connect case to ground plane. H. Case outline reference 2 place decimals are/C00340.030 (/C00340, 76 mm). 3 place decimals are/C00340.010 (/C00340, 25 mm). 4203195/A 08/01 0.017 (0,43) TYP. PC LAYOUT 0.025 (0,63) TYP. 0.90 (22,86) MAX. 0.160 (4,06) TYP. 1.11 (28,19) MAX. 0.95 (24,13) MAX. 0.310 (7,87) 0.040 (1,01) TYP. 0.032 (0,81) TYP. 0.860 (21,84) (3,55)0.140 0.100 (2,54) 0.090 (2,28) 0.050 (1,27) Note E 0.100 (2,54)

4 Places

ø0.045 (1,14) MIN. Plated through

5 Places

ø0.065 (1,65) MIN. 4 Places Plated through connected to ground plane 0.040 (1,01) 0.280 (7,11) 0.080 (2,03) 0.230 (5,84) (19,81) 0.780 0.960 (24,38) (21,84) 0.860 Note H Suffix A

MMSI002 – SEPTEMBER 2001 1POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 EFM (R–MSIP–G5) METAL SINGLE-IN-LINE MODULE NOTES: A. All linear dimensions are in inches (mm). B. This drawing is subject to change without notice. E. Recommended mechanical keep-out area. F. Power pin connections should utilize two or more vias per input, ground and output pin. G. Vias are recommended to improve copper adhesion. H. Solder mask openings to copper island for solder joints to mechanical pins. Electrically connect case to ground plane. I. Case outline reference. 2 place decimals are/C00340.030 (/C00340, 76 mm). 3 place decimals are/C00340.010 (/C00340, 25 mm). 4203196/A 08/01 0.017 (0,43) TYP. PC LAYOUT MAX. 0.90 (22,86) 0.160 (4,06) TYP. 0.100 (2,54) TYP. 1.11 (28,19) MAX. 0.95 (24,13) MAX. 0.310 (7,87) 0.040 (1,01) TYP. 0.032 (0,81) 0.860 (21,84) Note F 0.100 (2,54) ø0.065 (1,65) MIN. 4 Places Plated through connected to ground plane 0.040 (1,01) 0.280 (7,11) 0.080 (2,03) 0.230 (5,84) (19,81) 0.780 (5,33) 0.210 0.200 (5,08) 0.050 (1,27) 0.165 (4,19) 0.050 (1,27) 0.006 (0,15) 0.017 (0,43) TYP. 0.080 (2,03) Seating Plane 0.050 (1,27) 0.100 (3,55) 0.140 (2,54) 0.090 (2,28) (1,77) 0.070 0.100 (2,54) Note G Note H 0.025 (0,63) TYP. TYP. 0.050 (1,27) 0.960 (24,38) (24,13) 0.950 Note I 0.040 (1,01) Suffix C Gage Plane 0°–7°

MMSI065 – SEPTEMBER 2001 1POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 EFK (R–MSIP–T5) METAL SINGLE-IN-LINE MODULE 4203194/A 09/01 0.017 (0,43) TYP. 0.025 (0,63) TYP. MAX. 0.90 (22,86) 0.160 (4,06) TYP. 0.100 (2,54) TYP. 0.140 (3,55) MIN. 0.95 (24,13) MAX. 0.040 (1,01) TYP. 0.032(0,81)TYP. 0.860 (21,84) Note E ø0.045 (1,14) MIN. Plated through ø0.065 (1,65) MIN. 4 Places Plated through. See Note G. 0.040 (1,01) 0.48 (12,19) MAX. See Note F 0.94 (23,87) 0.200 (5,08) 0.35 0.51 (12,95) 0.230 (5,84) 0.100 (2,54) 0.080 (2,03)

2 Places

0.040 (1,01) 0.080 (2,03) (8,89) 0.310 (7,87) Note G Suffix N NOTES: A. All linear dimensions are in inches (mm). B. This drawing is subject to change without notice. C. 2 place decimals are ±0.030 (±0,76mm). D. 3 place decimals are ±0.010 (±0,25mm). E. Recommended mechanical keep out area. F. Electrical pin length mounted on circuit board seating plane to pin end. G. Electrically connect case to ground plane.

Texas InstrumentsIncorporatedand itssubsidiaries(TI)reservetherighttomake corrections,enhancements,improvementsand other changes toitssemiconductorproductsand servicesperJESD46, latestissue,and todiscontinueany productorserviceperJESD48, latest issue.Buyersshouldobtainthelatestrelevantinformationbeforeplacingordersand shouldverifythatsuch informationiscurrentand complete.Allsemiconductorproducts(alsoreferredtohereinas “components”)aresoldsubjecttoTI’s termsand conditionsofsale suppliedatthetimeoforderacknowledgment. TIwarrantsperformanceofitscomponents tothespecificationsapplicableatthetimeofsale,inaccordancewiththewarrantyinTI’s terms and conditionsofsaleofsemiconductorproducts.Testingand otherqualitycontroltechniquesareused totheextentTIdeems necessary tosupportthiswarranty.Exceptwhere mandated by applicablelaw,testingofallparametersofeach component isnotnecessarily performed. TIassumes no liabilityforapplicationsassistanceorthedesignofBuyers’products.Buyersareresponsiblefortheirproductsand applicationsusingTIcomponents.To minimizetherisksassociatedwithBuyers’productsand applications,Buyersshouldprovide adequatedesignand operatingsafeguards. TIdoes notwarrantorrepresentthatany license,eitherexpressorimplied,isgrantedunderany patentright,copyright,mask work right,or otherintellectualpropertyrightrelatingtoany combination,machine,orprocessinwhichTIcomponents orservicesareused.Information publishedby TIregardingthird-partyproductsorservicesdoes notconstitutea licensetouse such productsorservicesora warrantyor endorsementthereof.Use ofsuch informationmay requirea licensefroma thirdpartyunderthepatentsorotherintellectualpropertyofthe thirdparty,ora licensefromTIunderthepatentsorotherintellectualpropertyofTI. ReproductionofsignificantportionsofTIinformationinTIdatabooks ordatasheetsispermissibleonlyifreproductioniswithoutalteration and isaccompaniedby allassociatedwarranties,conditions,limitations,and notices.TIisnotresponsibleorliableforsuch altered documentation.Informationofthirdpartiesmay be subjecttoadditionalrestrictions. ResaleofTIcomponents orserviceswithstatementsdifferentfromorbeyond theparametersstatedby TIforthatcomponent orservice voidsallexpressand any impliedwarrantiesfortheassociatedTIcomponent orserviceand isan unfairand deceptivebusinesspractice. TIisnotresponsibleorliableforany such statements. Buyeracknowledgesand agreesthatitissolelyresponsibleforcompliancewithalllegal,regulatoryand safety-relatedrequirements concerningitsproducts,and any use ofTIcomponents initsapplications,notwithstandingany applications-relatedinformationorsupport thatmay be providedby TI.Buyerrepresentsand agreesthatithas allthenecessaryexpertisetocreateand implementsafeguardswhich anticipatedangerousconsequencesoffailures,monitorfailuresand theirconsequences,lessenthelikelihoodoffailuresthatmightcause harm and takeappropriateremedialactions.BuyerwillfullyindemnifyTIand itsrepresentativesagainstany damages arisingoutoftheuse ofany TIcomponents insafety-criticalapplications. Insome cases,TIcomponents may be promotedspecificallytofacilitatesafety-relatedapplications.Withsuch components,TI’s goalisto helpenablecustomerstodesignand createtheirown end-productsolutionsthatmeet applicablefunctionalsafetystandardsand requirements.Nonetheless,such components aresubjecttotheseterms. No TIcomponents areauthorizedforuse inFDA ClassIII(orsimilarlife-criticalmedicalequipment)unlessauthorizedofficersoftheparties have executeda specialagreementspecificallygoverningsuch use. OnlythoseTIcomponents whichTIhas specificallydesignatedas militarygradeor“enhanced plastic”aredesignedand intendedforuse in military/aerospaceapplicationsorenvironments.Buyeracknowledgesand agreesthatany militaryoraerospaceuse ofTIcomponents whichhave not been so designatedissolelyattheBuyer's risk,and thatBuyerissolelyresponsibleforcompliancewithalllegaland regulatoryrequirementsinconnectionwithsuch use. TIhas specificallydesignatedcertaincomponents as meetingISO/TS16949 requirements,mainlyforautomotiveuse.Inany case ofuse of non-designatedproducts,TIwillnotbe responsibleforany failuretomeet ISO/TS16949. Products Applications Audio www.ti.com/audio Automotiveand Transportationwww.ti.com/automotive Amplifiers amplifier.ti.com Communicationsand Telecom www.ti.com/communications Data Converters dataconverter.ti.com Computers and Peripherals www.ti.com/computers DLP ® Products www.dlp.com Consumer Electronics www.ti.com/consumer-apps DSP dsp.ti.com Energyand Lighting www.ti.com/energy Clocksand Timers www.ti.com/clocks Industrial www.ti.com/industrial Interface interface.ti.com Medical www.ti.com/medical Logic logic.ti.com Security www.ti.com/security Power Mgmt power.ti.com Space,Avionicsand Defense www.ti.com/space-avionics-defense Microcontrollers microcontroller.ti.com Videoand Imaging www.ti.com/video RFID www.ti-rfid.com OMAP ApplicationsProcessors www.ti.com/omap TIE2E Community e2e.ti.com WirelessConnectivity www.ti.com/wirelessconnectivity MailingAddress:Texas Instruments,PostOfficeBox 655303,Dallas,Texas 75265 Copyright© 2013,Texas InstrumentsIncorporated