PST26

PST26 PST | Alldatasheet

Document overview

• Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
• PDF pages: 11

Technical content

Features

PST26 Rev. 00 Page 2 of 11 www.powersystemtechnology.com A fuse mounted inside the converter protects against damages in case of a failure. The fuse is not user-accessible. In DC mode, reverse polarity at the input is protected and will not cause the fuse to blow . Model Fuse type Ra ng Reference PST26 Schurter 5A 0034.3124 Input Transient Protec on A VDR (Voltage Dependent Resistor) and a common mode input fi lter form an eff ec ve protec on against input transients in severe environ- ments. Electrical Input Data No Front panel (F) The PST26 is built as standard with a aluminum front panel as described in the mechanical data. In applica ons where the com- plete rack is covered by a single panel, the converter can be delivered without front panel. -40°C opera on (T) The thermal grade of the Vicor the DC/DC converters used and other components are changed to comply with low ambiant temperature. Conformal coa ng (V) During manufacturing process , when V op on is specifi ed, components and pcb are covered with an acrylic coa ng to address high level of ambiant humidity applica on. Op ons Descrip on Op ons Descrip on Input Input ̀ ഀ฀ༀ ĀȀ ̀ЀԀ Ȁ Ȁ ԀԀȀ ਀଀ ȀఀĀЀ ȀఀĀഀ Ԁ ฀ Ā ༀ ऀ ฀ ࠀᜀ က᠀ᤀᨀᬀᔀᰀሀጀᴀကሀጀᤀḀᰀကἀ !ᰀᔀᴀᨀ ᄀᔀ" ᠀ᤀᨀᬀᔀᰀሀጀᴀကሀጀᤀḀᰀကἀ !ᰀᔀᴀᨀ ᄀ#" $ᬀᨀ%Ḁᨀጀ"& Ȁ਀଀ఀက'ጀ ᐀) က+ ,! ᔀ#ကሀጀᤀḀᰀကᤀ (ᨀᬀ ฀ᰀကᄀሀጀကᰀ&ᤀ က'ᨀᔀ-ကሀጀᬀḀᜀ.က"Ḁᬀᬀᨀጀᰀ က/ᰀᔀᬀᰀ,Ḁᤀကᰀሀ᐀ᨀ

PST26 Rev. 00 Page 3 of 11 www.powersystemtechnology.com Output data for V1 PST26300 Output data for V2, V3 Electrical Output Data General condi ons : 25°C ambiant. Output data for V1 PST26150 V2,V3 are issued from V1, V1 must 12Vmin in order to have V2,V3 Unit Characteristics Conditions min typ max min typ max min typ max min typ max min typ max min typ max Output voltage 3,3 5 12 15 +-12 +-15 V Trim range (factory set) 3 3,6 4,5 5,5 11 13,2 13,5 16,5 8 15 13,5 16,5 V Overvoltage protection N/A N/A N/A N/A N/A N/A Nominal output current 5,5 5 2,5 2 1,25 1 A Output current limit 6 5,5 2,75 2,2 1,37 1,1 A Output noise 75 75 100 100 100 100 mVpp Load regulation 1 1 1 1 2 2 % Efficiency 80 82 86 87 87 87 % Max capacitive Load 470 470 470 470 220 220 µF +-15V Output V2(single) or V2,V3 (dual) 3V3 5V 12V 15V +-12V V2+V3 are isseud from V1. Max power for V1+V2+V3 150W. Power below is defined when V2 and V3 not used. Unit Characteristics Conditions min typ max min typ max min typ max min typ max min typ max min typ max min typ max Output voltage 3V3 5 12 15 24 28 48 V Trim range Factory set 3 3,6 4,5 5,5 10,8 13,2 13,5 16,5 21,6 26,2 25,2 30,8 43,2 51,8 V Overvoltage protection 4,5 6,5 14,9 18,5 29,1 34 58 V Nominal output current 0 15 0 15 0 12,5 0 10 0 6,25 0 5,3 0 3,1 A Output current limit 26 31 25 27 14,4 17,5 11,5 13,5 7,1 9 6,1 7,2 3,6 4,2 A Output noise 20MHz 75 75 100 100 100 100 150 mVpp Efficiency 75 83 85 84 83 84 % Load Regulation Vin nom. 2 2 0,5 0,5 0,4 0,4 0,4 % 28V 48V Output 3V3 5V 12V 15V 24V V2+V3 are isseud from V1. Max power for V1+V2+V3 300W. Power below is defined when V2 and V3 not used. Unit Characteristics Conditions min typ max min typ max min typ max min typ max min typ max min typ max min typ max Output voltage 3V3 5 12 15 24 28 48 V Trim range Factory set 3 3,6 4,5 5,5 10,8 13,2 13,5 16,5 21,6 26,2 25,2 30,8 43,2 51,8 V Overvoltage protection 4,5 6,5 14,9 18,5 29,1 34 58 V Nominal output current 0 30 0 30 0 25 0 20 0 12,5 0 10,6 0 6,25 A Output current limit 35 41 34 40 29 35 23 26 14,5 17 12,5 14,5 7,2 8,2 A Output noise 20MHz 75 75 100 100 100 100 150 mVpp Efficiency 75 83 85 84 83 84 % Load Regulation Vin nom. 1 1 0,5 0,5 0,4 0,4 0,4 % 28V 48V Output 3V3 5V 12V 15V 24V Output Output Output Output

Parallel and Series Connec on PST26 Rev. 00 Page 4 of 11 www.powersystemtechnology.com Redundant Systems Opera on Hold-up me The converters provide internal hold-up me (see curve). Hot Swap The hot swap is not recommended because of the inrush current. Ne- vertheless with some external cau ons it may be possible. We recom- mend to consult our technical support before opera ng in this mode. Output Current Limita on All outputs are con nously protected against short-circuit by a constant current limita on.(no foldback) Thermal Considera ons When a converter is mounted in free air, in convec on cooling, and is opera ng at its nominal output power at the max. ambiant temperatu- re, the temperature measured on the heatsink should not exeed 95°C. The dera ng curves show the max power available from the converter versus ambiant temperature. Thermal protec on A temperature protec on is integrated in each Vicor module, disabling output when heatsink temperature exceeds 105°C the converter auto- ma cally restarts, when the temperature drops below this limit. Never- theless, exeeding the max opera ng temperature may cause failures of the converter. 100 125 150 175 200 225 250 275 300 325 350 375 400 -20 0°C 20°C 40°C 60°C 80°C P(w) T°C PST26300 Output power vs Ambiant temp. Free air 2 m/s A converter output can be connected in series with an output from a separate converter, an external diode across each output is required. The maximum output current of a serial-connected outputs is limited by the output with the lowest current limit.Output voltages above 48V (SELV - Safety Extra Low Voltage) require addi onal safety measures in order to comply with interna onal safety requirements. Parrallel opera on is possible with the addi on of external diodes in series with each output. When systems require a very high level of reliability and should work normally in the event of a failure, N+1 redundancy is implemented where N is the number of converter to support power requirement. If one converter fail, the remaining ones s ll delivers the power to the loads. External diodes are required with the PST26 to ensure proper N+1 opera on . 100 125 150 175 200 225 -20 -10 0°C 10°C 20°C 30°C 40°C 50°C 60°C 70°C 80°C 85°C P(w) T°C PST26150 Output power vs ambiant temp. Free air 2m/s

Primary Inhibit (Remote On/Off ) PST26 Rev. 00 Page 5 of 11 www.powersystemtechnology.com The inhibit input disables (logic low, pull down or short circuit between Inhibit+ and Inbibit-) or enables (logic high TTL, pull up or open-circuit between Inhibit+ and Inhibit-) the converter. This signal is referenced to the input voltage and will disable/enable all outputs at the same me. In systems consis ng of several converters, this feature may be used to sequence the ac va on of the diff erent converters. Output Voltage Adjustment The converter outputs can be factory adjustable to diff erent values than standard ones. Consult factory. Sense Lines This feature enable compensa on of voltage drop across the connector contacts and the load lines. This fonc onnality is implemented on V1 only and only for the 300W confi gura on. The voltage between any sense line and its respec ve power output pin (as measured on the connector) should not exceed the following values at nominal output voltage. Output type Total drop Nega ve line drop V1 < 0.5V < 0.25V Powergood Two green leds on the front panel indicate the presence of output voltages . Waveforms Auxiliary Func onsAuxiliary Func ons Auxiliary Func ons Auxiliary Func ons Auxiliary Func ons Auxiliary Func ons PST26 output noise V1 24V Output noise V2, V3 +/- 15V

PST26 Rev. 00 Page 6 of 11 www.powersystemtechnology.com Electromagne c Emissions Level according to EN55011, EN55022 Standard Level Value Waveform Source imped. Test procedure Mode Criteria Surges Built to meet EN 61000-4-5 3 2000V 1,2 / 50 µs 12 ohms OP B OP B Built to meet Built to meet 10 pos., 10neg. OP B Electrical fast transients/burst EN 61000-4-4 4 4000V 5 / 50µs 50 ohms Electrostatic discharge (to case) EN 6100-4-2 4 8000V 1 / 50µs 330 Ohms Electromagne c Electromagne c Electromagne c Immunity to Environmental Condi ons Test method Standard Test conditions Status 20g / 11ms 5g / 30ms Vibrations MIL STD 810D Proc. 514-3 Built to meet Damp Heat MIL STD 810D Proc. 507-2 Humidity 93 %, 40°C, 56 days Conformal coating option only (V), built to meet Shock MIL STD 810D Proc.516.3 Built to meet

PST26 Rev. 00 Page 7 of 11 www.powersystemtechnology.com Solder side of the PCB protected by PBT sheet. Mechanical data Mechanical data Mechanical data

PST26 Rev. 00 Page 8 of 11 www.powersystemtechnology.com Connector Pin Alloca on Ref : 05H15MGWVZ32/K1 - 2E ROLF HILLER DIN 41612 Male H15 - Short version Safety and Installa ons Instruc ons Safety and Installa ons Instruc ons Safety and Installa ons Instruc ons PIN

4 NC No connection

6 NC No connection

8 V1+ Output 1+

10 V1- Output 1-

12 V2 Output 2

14 V3 Output 3

16 NC No connection

18 NC No connection

20 V2/V3 Com Output 2 and 3 Return

22 NC No connection

24 AC/L Input Ac Line

26 ON/OFF inhibit-

28 AC/N Input Ac Neutral

30 ON/OFF inhibit+

32 Earth

4 V1+ Output 1+

6 V1+ Output 1+

8 V1- Output 1-

16 S1+ Output 1 Senses +

18 S1- Output 1 Senses -

Description

PST26 Rev. 00 Page 9 of 11 www.powersystemtechnology.com These converters are components, intended exclusively for integra on into other equipment by an industrial assembly process or by a profes- sionally competent person. Installa on must strictly follow the safety regula ons in respect of the enclosure, moun ng, creepage and clea- rance distances, markings of the end-use applica on. Connec on to the system shall be made via the female connector H15. Pin 32 (Earth) is a leading pin and is connected to the case. For safety reasons it is essen al to connect this pin to the protec ve earth of the supply system. The AC/L is internally fused. This fuse is designed to protect the con- verter against overcurrent caused by a failure, but may not be able to sa sfy all requirements. External fuses in the wiring circuit to one or both input pins (28 or 24) may be necessary to ensure compliance with local requirements. Do not open the converters, or the warranty will be invalidated. Make sure that there is suffi cient airfl ow available for convec on cooling. This should be verifi ed by measuring the case of temperature at the specifi ed measuring point, when the converter is operated in the end- use applica on. Cleaning Agents and Process The converters are not herme cally sealed. In order to avoid possible damage, any penetra on of liquids shall be avoided. Isola on The electric strength test is performed in the factory in accordance with IEC/EN 60950. Standards and Approvals The converters are built to meet the safety standards IEC 60950-1, EN 60950-1. ‘Built to meet’ men onned in the diff erent paragraphs of the datasheet means that Power System Technology has designed the product to meet the standard but not cer fi ed it in a laboratory. Electric Strength Design strength 1500 3000 500 Vrms > 100 >100 MohmsInsulation resistance Characteristic Output to Output Unit Electric strength Factory test for production units (>10s) 2000 2000 500 Vdc Input to Earth Input to Output Output to Earth Temperatures -20 +71 -40 +71 -20 +100 -48 +100 Not operating -40 +125 -40 +125 Ambiant Operating (see derating) °CHeatsink Storage Standard T option UnitConditions Reliability MIL-HDBK-217F, notice 2 Model Heatsink Temp. GB GF 40°C 285000 165000 70°C 139500 82300 100°C 86600 51000 MTBF ( Hours) PST26150 3 outputs

PST26 Rev. 00 Page 10 of 11 www.powersystemtechnology.com Max. power available : 150W IN max : see table page 2 PST26150 Vout Pout Op on 3V3 50 F T V F : No front panel T : -40°C V : Conformal coa ng IN max : see table page 2 PST26150 Vout Pout Op on 150 F R S T V Vout Pout 3V3 12D 15D V2 / V3 F : No front panel T : -40°C V : Conformal coa ng Op ons and confi gura ons Op ons and confi gura ons Op ons and confi gura ons Single Dual / Triple 5 75 12 150 15 150 24 150 28 150 48 150 D : +/-

PST26 Rev. 00 Page 11 of 11 www.powersystemtechnology.com Max. power available : 300W IN max : see table page 2 PST26300 Vout Pout Op on F T V F : No front panel T : -40°C V : Conformal coa ng IN max : see table page 2 PST26300 Vout Pout Op on 300 F R S T V Vout Pout 3V3 12D 15D V2 / V3 F : No front panel T : -40°C V : Conformal coa ng Single Dual / Triple 3V3 100 5 150 12 300 15 300 24 300 28 300 48 300 D : +/-