PS9821-2-V-AX

PS9821-1_V01 RENESAS | Alldatasheet

Document overview

• Manufacturer or author: Renesas Electronics Corporation
• PDF pages: 15

Technical content

R08DS0260EJ0100 Rev.1.00 Page 1 of 14 Dec 17, 2021 Data S heet PS9821-1,-2 HIGH CMR, 15 Mbps OPEN COLLECTOR OUTPUT TYPE 8-PIN SSOP (SO-8) 3.3 V HIGH-SPEED PHOTOCOUPLER

DESCRIPTION

The PS9821-1 and PS9821-2 are active-low type high-speed photocouplers that use an AlGaAs light-emitting diode on the input side and a photodetector IC that includes a photodiode and a signal processor on the same chip on the output side. The PS9821-1, -2 are designed specifically for high common mode transient immunity (CMR) and low pulse width distortion, PS9821-2 is suitable for high density applications.

FEATURES

• Low power consumption (VCC = 3.3 V)
• Pulse width distortion (tPHL−tPLH = 35 ns MAX.)
• High common mode transient immunity (CMH, CML = ±15 kV/µs MIN.)
• 40% reduction of mounting area (5-pin SOP × 2)
• High-speed (15 Mbps)
• High isolation voltage (BV = 2 500 Vr.m.s.)
• Open collector output
• Ordering number of tape product: PS9821-1-F3 : 1 500 pcs/reel : PS9821-2-F3 : 1 500 pcs/reel
• Pb-Free product
• Safety standards
• UL ：UL1577, Single protection
• CSA ：CAN/CSA-C22.2 No.62368-1, Basic insulation
• VDE ：DIN EN 60747-5-5 (Option)

APPLICATIONS

• Measurement equipment
• PDP
• FA Network TRUTH TABLE LED Output ON L OFF H R08DS0260EJ0100 Rev.1.00 Dec 17, 2021 Start of mass production Sep.2004 PIN CONNECTION (Top View) 8. VCC 6. VO 1. NC 2. Anode 3. Cathode 4. NC 5. GND 7. NC SHIELD 1 2 3 4 8 7 6 5 PS9821−1 1. Anode1 2. Cathode1 3. Cathode2 4. Anode2 5. GND 6. VO2 7. VO1 8. VCC PS9821−2 SHIELD SHIELD 1 2 3 4 8 7 6 5

PS9821-1,-2 Data Sheet R08DS0260EJ0100 Rev.1.00 Page 2 of 14 Dec 17, 2021 PACKAGE DIMENSIONS (UNIT: mm) Weight: 0.14g (typ.) PHOTOCOUPLER CONSTRUCTION Parameter Unit (MIN.) Air Distance 4 mm Creepage Distance 4 mm Isolation Distance 0.2 mm MARKING EXAMPLE Ni/Pd/Au PLATING 1.27 0.4+0.10 −0.05 0.25 M 0.1±0.1 3.95±0.1 6.0±0.2 0.5±0.3 0.15+0.10 −0.05 5.21±0.25 3.27±0.2 0.10 S No. 1 pin Mark Initial of Renesas (Engraved mark) PS9821−1 PS9821−2 No. 1 pin Mark Initial of Renesas (Engraved mark) R 9821−2 NT831 Week Assembled R 9821−1 NT831 8 31 Year Assembled (Last 1 Digit) TN Rank Code In-house Code 8 31 Year Assembled (Last 1 Digit) TN Rank Code In-house Code Week Assembled Type Number Assembly Lot Type Number Assembly Lot

PS9821-1,-2 Data Sheet R08DS0260EJ0100 Rev.1.00 Page 3 of 14 Dec 17, 2021

ORDERING INFORMATION

Part Number Order Number Solder Plating Specification Packing Style Safety Standard Approval Application Part Number*1 PS9821-1 PS9821-1-AX Pb-Free (Ni/Pd/Au) 20 pcs (Tape 20 pcs cut) Standard products (UL, CSA approved) PS9821-1 PS9821-1-F3 PS9821-1-F3-AX Embossed Tape 1 500 pcs/reel PS9821-2 PS9821-2-AX 20 pcs (Tape 20 pcs cut) PS9821-2 PS9821-2-F3 PS9821-2-F3-AX Embossed Tape 1 500 pcs/reel PS9821-1-V PS9821-1-V-AX 20 pcs (Tape 20 pcs cut) UL, CSA, DIN EN 60747-5-5 approved PS9821-1 PS9821-1-V-F3 PS9821-1-V-F3-AX Embossed Tape 1 500 pcs/reel PS9821-2-V PS9821-2-V-AX 20 pcs (Tape 20 pcs cut) PS9821-2 PS9821-2-V-F3 PS9821-2-V-F3-AX Embossed Tape 1 500 pcs/reel Notes*: 1. For the application of the Safety Standard, following part number should be used. ABSOLUTE MAXIMUM RATINGS (TA = 25 °C, unless otherwise specified) Parameter Symbol Ratings Unit PS9821-1 PS9821-2 Diode Forward Current IF 20*1 15*2 mA Reverse Voltage VR 5 V/ch Detector Supply Voltage VCC 7 V Output Voltage VO 7 V/ch Output Current IO 25 mA/ch Power Dissipation *3 PC 40 mW/ch Isolation Voltage *4 BV 2 500 Vr.m.s. Operating Ambient Temperature TA − 40 to + 85 °C Storage Temperature Tstg − 55 to + 125 °C Notes*: 1. Reduced to 0.3 mA/°C at TA = 60 °C or more. 2. Reduced to 0.1 mA/°C at TA = 60 °C or more. 3. Applies to output pin VO (collector pin). Reduced to 1.5 mW/°C at TA = 65 °C or more. 4. AC voltage for 1 minute at TA = 25 °C, RH = 60 % between input and output. Pins 1-4 shorted together, 5-8 shorted together. RECOMMENDED OPERATING CONDITIONS Parameter Symbol MIN. TYP. MAX. Unit Low Level Input Voltage VFL 0 0.8 V High Level Input Current IFH 6.3 10 12.5 mA Supply Voltage VCC 2.7 3.6 V Pull-up Resistance RL 330 4 k Ω TLL (RL = 1.0 kΩ, loads) N 5

PS9821-1,-2 Data Sheet R08DS0260EJ0100 Rev.1.00 Page 4 of 14 Dec 17, 2021 ELECTRICAL CHARACTERISTICS (1/2) (TA = −40 to +85 °C, unless otherwise specified) Parameter Symbol Conditions MIN. TYP. *1 MAX. Unit Diode Forward Voltage VF IF = 10 mA, TA = 25 °C 1.4 1.65 1.8 V Reverse Current IR VR = 3.0 V, TA = 25 °C 10 µA Terminal Capacitance Ct VF = 0 V, f = 1 MHz, TA = 25 °C 30 pF Detector High Level Output Current I OH V CC = VO = 3.3 V, IF = 0.8 mA 1 80 µA V CC = VO = 5.5 V, IF = 0.8 mA 1 *2 Low Level Output Voltage *3 V OL V CC = 3.3 V, IF = 5.0 mA, IOL = 13 mA 0.2 0.6 V V CC = 5.5 V, IF = 5.0 mA, IOL = 13 mA 0.2*2 High Level Supply Current ICCH V CC = 3.3 V, IF = 0 mA, VO = open 4 7 mA (PS9821-1) V CC = 5.5 V, IF = 0 mA, VO = open 5 *2 High Level Supply Current V CC = 3.3 V, IF = 0 mA, VO = open 8 14 (PS9821-2) V CC = 5.5 V, IF = 0 mA, VO = open 10*2 Low Level Supply Current ICCL V CC = 3.3 V, IF = 10 mA, VO = open 7 10 (PS9821-1) V CC = 5.5 V, IF = 10 mA, VO = open 9 *2 Low Level Supply Current V CC = 3.3 V, IF = 10 mA, VO = open 14 20 (PS9821-2) V CC = 5.5 V, IF = 10 mA, VO = open 18*2 Coupled Threshold Input Current IFHL VCC = 3.3 V, VO = 0.8 V, RL = 350 Ω 2.5 5 mA (H → L) VCC = 5 V, VO = 0.8 V, RL = 350 Ω 2.5*2 Isolation Resistance RI-O VI-O = 1 kVDC, RH = 40 to 60 %, TA = 25 °C 1011 Ω Insulation Resistance (Input-Input), (PS9821-2) RI-I VI-I = 1 kVDC, RH = 40 to 60 %, TA = 25 °C 1010 Ω Isolation Capacitance CI-O V = 0 V, f = 1 MHz, TA = 25 °C 0.6 pF Insulation Capacitance (Input-Input), (PS9821-2) CI-I V = 0 V, f = 1 MHz, TA = 25 °C 0.3 pF Propagation Delay Time t PHL TA = 25 °C 45 75 ns (H → L) *4 VCC = 3.3 V, RL = 350 Ω, IF = 7.5 mA 100 VCC = 5 V, RL = 350 Ω, IF = 7.5 mA 38*2 Propagation Delay Time t PLH TA = 25 °C 50 75 (L → H) *4 VCC = 3.3 V, RL = 350 Ω, IF = 7.5 mA 100 VCC = 5 V, RL = 350 Ω, IF = 7.5 mA 43*2 Rise Time tr VCC = 3.3 V, RL = 350 Ω, IF = 7.5 mA 20 VCC = 5 V, RL = 350 Ω, IF = 7.5 mA 20*2 Fall Time tf VCC = 3.3 V, RL = 350 Ω, IF = 7.5 mA 5 VCC = 5 V, RL = 350 Ω, IF = 7.5 mA 5 *2 Pulse Width Distortion (PWD) *4 tPLH−tPHL VCC = 3.3 V, RL = 350 Ω, IF = 7.5 mA 5 35 VCC = 5 V, RL = 350 Ω, IF = 7.5 mA 5 *2 Propagation Delay Skew t PSK VCC = 3.3 V, RL = 350 Ω, IF = 7.5 mA 40

PS9821-1,-2 Data Sheet R08DS0260EJ0100 Rev.1.00 Page 5 of 14 Dec 17, 2021 ELECTRICAL CHARACTERISTICS (2/2) (TA = −40 to +85 °C, unless otherwise specified) Parameter Symbol Conditions MIN. TYP. *1 MAX. Unit Coupled Common Mode Transient Immunity at High Level Output*5 CMH VCC = 3.3 V, RL = 350 Ω, TA = 25 °C, IF = 0 mA, VO > 2 V, VCM = 1 kV 15 20 kV/µs VCC = 5 V, RL = 350 Ω, TA = 25 °C, IF = 0 mA, VO > 2 V, VCM = 1 kV 20*2 Common Mode Transient Immunity at Low Level Output CML VCC = 3.3 V, RL = 350 Ω, TA = 25 °C, IF = 7.5 mA, VO < 0.8 V, VCM = 1 kV 15 20 VCC = 5 V, RL = 350 Ω, TA = 25 °C, IF = 7.5 mA, VO < 0.8 V, VCM = 1 kV 20*2 Notes*: 1. Typical values at TA = 25 °C 2. These values are reference values. 3. Because VOL of 2 V or more may be output when LED current input and when output supply of VCC = 2.6 V or less, it is important to confirm the characteristics (operation with the power supply on and off) during design, before using this device. 4. Test circuit for propagation delay time. Remark: CL includes probe and stray wiring capacitance. PS9821−1 SHIELD SHIELD PS9821−2 IF VO 50% 1.5 V VOLtPHL tPLH (IF = 7.5 mA) VCC = 3.3 V 0.1 μF CL = 15 pF 47 Ω RL = 350 Ω VCC = 3.3 V 0.1 μF CL = 15 pF47 Ω RL = 350 Ω Pulse Input (IF) (PW = 1 μs, Duty cycle = 1/10) IF Monitor VO VO Pulse Input (IF) (PW = 1 μs, Duty cycle = 1/10) IF Monitor

PS9821-1,-2 Data Sheet R08DS0260EJ0100 Rev.1.00 Page 6 of 14 Dec 17, 2021 5. Test circuit for common mode transient immunity Remark: C L includes probe and stray wiring capacitance. USAGE CAUTIONS 1. This product is weak for static electricity by designed with high-speed integrated circuit so protect against static electricity when handling. 2. By-pass capacitor of 0.1 µF is used between VCC and GND near device. Also, ensure that the distance between the leads of the photocoupler and capacitor is no more than 10 mm. 3. Avoid storage at a high temperature and high humidity. 4. Avoid cleaning with Freon based or halogen-based (chlorinated etc.) solvents. 5. Do not use fixing agents or coatings containing halogen-based substances. 90% 10% 1 kV 0 V VOH 2 V 0.8 V VOL VCM VO (IF = 0 mA) VO (IF = 7.5 mA) tr tf SW IF VO VCC = 3.3 V 0.1 μF RL = 350 Ω PS9821−1 VCM CL = 15 pF SHIELD SHIELD VO VCC = 3.3 V 0.1 μF RL = 350 Ω VCM SW IF CL = 15 pF PS9821−2

PS9821-1,-2 Data Sheet R08DS0260EJ0100 Rev.1.00 Page 7 of 14 Dec 17, 2021 TYPICAL CHARACTERISTICS (TA = 25 °C unless otherwise specified) Remark The graphs indicate nominal characteristics. DETECTOR POWER DISSIPATION vs. AMBIENT TEMPERATURE Ambient Temperature TA (°C) Detector Power Dissipation PC (mW) 20 40 60 80 85 1000 Forward Voltage VF (V) Forward Current IF (mA) FORWARD CURRENT vs. FORWARD VOLTAGE 1.0 0.01 0.1 100 TA = +85°C +50°C +25°C 0°C −25°C −50 −25 0 25 50 75 100 0.6 0.5 0.4 0.3 0.2 0.1 −50 −25 0 25 50 75 1000 ICCL (VCC = 3.3 V, IF = 10 mA), PS9821-2 ICCH (VCC = 3.3 V, IF = 0 mA), PS9821-1 ICCL (VCC = 3.3 V, IF = 10 mA), PS9821-1 ICCH (VCC = 3.3 V, IF = 0 mA), PS9821-2 Ambient Temperature TA (°C) Maximum Forward Current IF (mA) MAXIMUM FORWARD CURRENT vs. AMBIENT TEMPERATURE 20 40 60 80 1000 85 PS9821−1 PS9821−2 Ambient Temperature TA (°C) High Level Supply Current ICCH (mA) Low Level Supply Current ICCL (mA) SUPPLY CURRENT vs. AMBIENT TEMPERATURE Input Current IF (mA) Output Voltage VO (V) OUTPUT VOLTAGE vs. INPUT CURRENT Ambient Temperature TA (°C) Low Level Output Voltage VOL (V) LOW LEVEL OUTPUT VOLTAGE vs. AMBIENT TEMPERATURE IF = 5.0 mA, VCC = 3.3 V 13.0 mA 10.0 mA 6.0 mA IOL = 16.0 mA 1 2 3 4 5 6 3.5 2.5 1.5 0.5 VCC = 3.3 V 4.0 kΩ, 4.7 kΩ 1.0 kΩ RL = 350 Ω

PS9821-1,-2 Data Sheet R08DS0260EJ0100 Rev.1.00 Page 8 of 14 Dec 17, 2021 Remark The graphs indicate nominal characteristics. 5.0 4.0 3.0 2.0 1.0 100 120 100 −50 −25 0 25 50 75 100 −50 −25 0 25 50 75 100 −50 −25 0 25 50 75 100 151311975 −50 −25 0 25 50 75 100 300 250 200 150 100 120 100 THRESHOLD INPUT CURRENT vs. AMBIENT TEMPERATURE Ambient Temperature TA (°C) Threshold Input Current IFHL (mA) Ambient Temperature TA (°C) Propagation Delay Time tPHL, tPLH (ns) PROPAGATION DELAY TIME vs. AMBIENT TEMPERATURE Ambient Temperature TA (°C) Pulse Width Distortion |tPHL− tPLH| (ns) PULSE WIDTH DISTORTION vs. AMBIENT TEMPERATURE Ambient Temperature TA (°C) Switching Time tr, tf (ns) SWITCHING TIME vs. AMBIENT TEMPERATURE Input Current IF (mA) Propagation Delay Time tPHL, tPLH (ns) PROPAGATION DELAY TIME vs. INPUT CURRENT 1.0 kΩ RL = 350 Ω 4.0 kΩ VCC = 3.3 V, VO = 0.6 V RL = 4.7 kΩ RL = 4.0 kΩ RL = 350 Ω RL = 1.0 kΩ IF = 7.5 mA, VCC = 3.3 V tPLH: RL = 4.0 kΩ tPLH: RL = 4.7 kΩ tPLH: RL = 1.0 kΩ tPLH: RL = 350 Ω VCC = 3.3 V tPHL: RL = 350 Ω, 1.0 kΩ, 4.0 kΩ, 4.7 kΩ tPHL: RL = 350 Ω, 1.0 kΩ, 4.0 kΩ, 4.7 kΩ tPLH: RL = 1.0 kΩ tPLH: RL = 350 Ω tPLH: RL = 4.7 kΩ tPLH: RL = 4.0 kΩ IF = 7.5 mA, VCC = 3.3 V tf: RL = 350 Ω, 1.0 kΩ, 4.0 kΩ, 4.7 kΩ tr: RL = 350 Ω tr: RL = 1.0 kΩ tr: RL = 4.7 kΩ tr: RL = 4.0 kΩ IF = 7.5 mA, VCC = 3.3 V

PS9821-1,-2 Data Sheet R08DS0260EJ0100 Rev.1.00 Page 9 of 14 Dec 17, 2021 TAPING SPECIFICATIONS (UNIT: mm) Outline and Dimensions (Reel) Packing: 1 500 pcs/reel 2.0±0.5 R1.0 ⌀13.0±0.2 ⌀21.0±0.8 ⌀330±2.0 ⌀100±1.0 2.0±0.5 17.5±1.0 13.5±1.0 ⌀1.7±0.1 2.0±0.05 4.0±0.1 1.75±0.1 6.4±0.1 5.56±0.1 0.3±0.058.0±0.1 ⌀1.5+0.1 5.5±0.1 12.0±0.2 3.6±0.1 4.05 MAX. Outline and Dimensions (Tape) Taping Direction 8-pin SOP (F3)

PS9821-1,-2 Data Sheet R08DS0260EJ0100 Rev.1.00 Page 10 of 14 Dec 17, 2021 RECOMMENDED MOUNT PAD DIMENSIONS (UNIT: mm) Remark All dimensions in this figure must be evaluated before use. 1.45 0.81.27 5.25

PS9821-1,-2 Data Sheet R08DS0260EJ0100 Rev.1.00 Page 11 of 14 Dec 17, 2021 NOTES ON HANDLING 1. Recommended soldering conditions (1) Infrared reflow soldering

• Peak reflow temperature 260 °C or below (package surface temperature)
• Time of peak reflow temperature 10 seconds or less
• Time of temperature higher than 220 °C 60 seconds or less
• Time to preheat temperature from 120 to 180 °C 120 ± 30 s
• Number of reflows Three
• Flux Rosin flux containing small amount of chlorine (The flux with a maximum chlorine content of 0.2 Wt% is recommended.) (2) Wave soldering
• Temperature 260 °C or below (molten solder temperature)
• Time 10 seconds or less
• Preheating conditions 120 °C or below (package surface temperature)
• Number of times One (Allowed to be dipped in solder including plastic mold portion.)
• Flux Rosin flux containing small amount of chlorine (The flux with a maximum chlorine content of 0.2 Wt% is recommended.) (3) Soldering by Soldering Iron
• Peak Temperature (lead part temperature) 350 °C or below
• Time (each pins) 3 seconds or less
• Flux Rosin flux containing small amount of chlorine (The flux with a maximum chlorine content of 0.2 Wt% is recommended.) (a) Soldering of leads should be made at the point 1.5 to 2.0 mm from the root of the lead (b) Please be sure that the temperature of the package would not be heated over 100 °C (4) Cautions
• Flux Cleaning Avoid cleaning with Freon based or halogen-based (chlorinated etc.) solvents.
• Do not use fixing agents or coatings containing halogen-based substances. 2. Cautions regarding noise Be aware that when voltage is applied suddenly between the photocoupler’s input and output or between collector-emitters at startup, the output transistor may enter the on state, even if the voltage is within the absolute maximum ratings. 120±30 s (preheating) 220°C 180°C Package Surface Temperature T (°C) Time (s) Recommended Temperature Profile of Infrared Reflow (heating) to 10 s to 60 s 260°C MAX. 120°C

PS9821-1,-2 Data Sheet R08DS0260EJ0100 Rev.1.00 Page 12 of 14 Dec 17, 2021 SPECIFICATION OF VDE MARKS LICENSE DOCUMENT Parameter Symbol Rating Unit Climatic test class (IEC 60068-1/DIN EN 60068-1) 55/100/21 Dielectric strength maximum operating isolation voltage Test voltage (partial discharge test, procedure a for type test and random test) Upr = 1.6 × UIORM., Pd < 5 pC UIORM Upr 566 849 Vpeak Vpeak Test voltage (partial discharge test, procedure b for all devices) Upr = 1.875 × UIORM., Pd < 5 pC Upr 1 061 V peak Highest permissible overvoltage UIOTM 4 000 Vpeak Degree of pollution (IEC 60664-1/DIN EN 60664-1 (VDE 0110-1)) 2 Comparative tracking index (IEC 60112/DIN EN 60112 (VDE 0303-11)) CTI 175 Material group (IEC 60664-1/DIN EN 60664-1 (VDE 0110-1)) III a Storage temperature range Tstg − 55 to +125 °C Operating temperature range TA − 40 to +85 °C Isolation resistance, minimum value VIO = 500 V dc at TA = 25 °C VIO = 500 V dc at TA MAX. at least 100 °C Ris MIN. Ris MIN. 1012 1011 Ω Ω Safety maximum ratings (maximum permissible in case of fault, see thermal derating curve) Package temperature Current (input current IF, Psi = 0) Power (output or total power dissipation) Isolation resistance VIO = 500 V dc at TA = Tsi Tsi Isi Psi Ris MIN. 150 150 600 109 mA mW Ω Dependence of maximum safety ratings with package temperature 100 200 300 400 500 600 700 800 900 1000 0 25 50 75 100 125 150 175 200 Package temp Tsi (°C) Total Power Dissipation Psi (mW) Input Current Isi (mA) Psi: Total Power Dissipation Isi: Input Current

PS9821-1,-2 Data Sheet R08DS0260EJ0100 Rev.1.00 Page 13 of 14 Dec 17, 2021 Method a) Destructive Test, Type and Sample Test Method b) Non-destructive Test, 100% Production Test UIOTM = 4000 V Upr = 905 V UIORM = 566 V t1 tini t2 t3 tm t4 V t t1, t2 = 1 to 10 sec t3, t4 = 1 sec tm(PARTIAL DISCHARGE) = 10 sec ttest = 12 sec tini = 60 sec ttest Upr = 1061 V UIORM = 566 V t3 t4 ttest t tm V t3, t4 = 0.1 sec tm(PARTIAL DISCHARGE) = 1.0 sec ttest = 1.2 sec

PS9821-1,-2 Data Sheet R08DS0260EJ0100 Rev.1.00 Page 14 of 14 Dec 17, 2021 Caution GaAs Products This product uses gallium arsenide (GaAs). GaAs vapor and powder are hazardous to human health if inhaled or ingested, so please observe the following points.

• Follow related laws and ordinances when disposing of the product. If there are no applicable laws and/or ordinances, dispose of the product as recommended below. 1. Commission a disposal company able to (with a license to) collect, transport and dispose of materials that contain arsenic and other such industrial waste materials. 2. Exclude the product from general industrial waste and household garbage, and ensure that the product is controlled (as industrial waste subject to special control) up until final disposal.
• Do not burn, destroy, cut, crush, or chemically dissolve the product.
• Do not lick the product or i any way allow it to enter the mouth. All trademarks and registered trademarks are the property of their respective owners.

© 2021 Renesas Electronics Corporation. All rights reserved. Notice 1. Descriptions of circuits, software and other related information in this document are provided only to illustrate the operation of semiconductor products and application examples. You are fully responsible for the incorporation or any other use of the circuits, software, and information in the design of your product or system. Renesas Electronics disclaims any and all liability for any losses and damages incurred by you or third parties arising from the use of these circuits, software, or information. 2. Renesas Electronics hereby expressly disclaims any warranties against and liability for infringement or any other claims involving patents, copyrights, or other intellectual property rights of third parties, by or arising from the use of Renesas Electronics products or technical information described in this document, including but not limited to, the product data, drawings, charts, programs, algorithms, and application examples. 3. No license, express, implied or otherwise, is granted hereby under any patents, copyrights or other intellectual property rights of Renesas Electronics or others. 4. You shall be responsible for determining what licenses are required from any third parties, and obtaining such licenses for the lawful import, export, manufacture, sales, utilization, distribution or other disposal of any products incorporating Renesas Electronics products, if required. 5. You shall not alter, modify, copy, or reverse engineer any Renesas Electronics product, whether in whole or in part. Renesas Electronics disclaims any and all liability for any losses or damages incurred by you or third parties arising from such alteration, modification, copying or reverse engineering. 6. Renesas Electronics products are classified according to the following two quality grades: “Standard” and “High Quality”. The intended applications for each Renesas Electronics product depends on the product’s quality grade, as indicated below. "Standard": Computers; office equipment; communications equipment; test and measurement equipment; audio and visual equipment; home electronic appliances; machine tools; personal electronic equipment; industrial robots; etc. "High Quality": Transportation equipment (automobiles, trains, ships, etc.); traffic control (traffic lights); large -scale communication equipment; key financial terminal systems; safety control equipment; etc. Unless expressly designated as a high reliability product or a product for harsh environments in a Renesas Electronics data sheet or other Renesas Electronics document, Renesas Electronics products are not intended or authorized for use in products or systems that may pose a direct threat to human life or bodily injury (artificial life support devices or systems; surgical implantations; etc.), or may cause se rious property damage (space system; undersea repeaters; nuclear power control systems; aircraft control systems; key plant systems; military equipment; etc.). Renesas Electronics disclaims any and all liability for any damages or losses incurred by you or any third parties arising from the use of any Renesas Electronics product that is inconsistent with any Renesas Electronics data sheet, user’s manual or other Renesas Electronics document. 7. No semiconductor product is absolutely secure. Notwithstanding any security measures or features that may be implemented in Renesas Electronics hardware or software products, Renesas Electronics shall have absolutely no liability arising out of any vulnerability or sec urity breach, including but not limited to any unauthorized access to or use of a Renesas Electronics product or a system that uses a Renesas Electronics product. RENESAS ELECTRONICS DOES NOT WARRANT OR GUARANTEE THAT RENESAS ELECTRONICS PRODUCTS, OR ANY SYSTEMS CREATED USING RENESAS ELECTRONICS PRODUCTS WILL BE INVULNERABLE OR FREE FROM CORRUPTION, ATTACK, VIRUSES, INTERFERENCE, HACKING, DATA LOSS OR THEFT, OR OTHER SECURITY INTRUSION (“Vulnerability Issues”). RENESAS ELECTRONICS DISCLAIMS ANY AND ALL RESPONSIBILITY OR LIABILITY ARISING FROM OR RELATED TO ANY VULNERABILITY ISSUES. FURTHERMORE, TO THE EXTENT PERMITTED BY APPLICABLE LAW, RENESAS ELECTRONICS DISCLAIMS ANY AND ALL WARRANTIES, EXPRESS OR IMPLIED, WITH RESPECT TO THIS DOCUMENT AND ANY RELATED OR ACCOMPANYING SOFTWARE OR HARDWARE, INCLUDING BUT NOT LIMITED TO THE IMPLIED WARRANTIES OF MERCHANTABILITY, OR FITNESS FOR A PARTICULAR PURPOSE. 8. When using Renesas Electronics products, refer to the latest product information (data sheets, user’s manuals, application notes, “General Notes for Handling and Using Semiconductor Devices” in the reliability handbook, etc.), and ensure that usage conditions are within the ranges specified by Renesas Electronics with respect to maximum ratings, operating power supply voltage range, heat dissipation characteristics, installation, etc. Renesas Electronics disclaims any and all liability for any malfunctions, failure or accident arising out of the use of Renesas Elect ronics products outside of such specified ranges. 9. Although Renesas Electronics endeavors to improve the quality and reliability of Renesas Electronics products, semiconductor products have specific characteristics, such as the occurrence of failure at a certain rate and malfunctions under certain use conditions. Unless designated as a high reliabilit y product or a product for harsh environments in a Renesas Electronics data sheet or other Renesas Electronics document, Renesas Electronics products are not subject to radiation resistance design. You are responsible for implementing safety measures to guard against the possibility of bodily injury, injury or damage caused by fire, and/or danger to the public in the event of a failure or malfunction of Renesas Electronics products, such as safety design for hardware and software, including but not limited to redundancy, fire control and malfunction prevention, appropriate treatment for aging degradation or any other appropriate measures. Because the evaluation of microcomputer software alone is very difficult and impractical, you are responsible for evaluating the safety of the final products or systems manufactured by you. 10. Please contact a Renesas Electronics sales office for details as to environmental matters such as the environmental compatibility of each Renesas Electronics product. You are responsible for carefully and sufficiently investigating applicable laws and regulations that regulate the inclusion or use of controlled substances, including without limitation, the EU RoHS Directive, and using Renesas Electronics products in compliance with all these applicable laws and regulations. Renesas Electronics disclaims any and all liability for damages or losses occurring as a result of your noncompliance with applicable laws and regulations. 11. Renesas Electronics products and technologies shall not be used for or incorporated into any products or systems whose manufacture, use, or sale is prohibited under any applicable domestic or foreign laws or regulations. You shall comply with any applicable export control laws and regulations promulgated and administered by the governments of any countries asserting jurisdiction over the parties or transactions. 12. It is the responsibility of the buyer or distributor of Renesas Electronics products, or any other party who distributes, disposes of, or otherwise sells or transfers the product to a third party, to notify such third party in advance of the contents and conditions set forth in this document. 13. This document shall not be reprinted, reproduced or duplicated in any form, in whole or in part, without prior written consent of Renesas Electronics. 14. Please contact a Renesas Electronics sales office if you have any questions regarding the information contained in this document or Renesas Electronics products. (Note1) “Renesas Electronics” as used in this document means Renesas Electronics Corporation and also includes its directly or indirectly controlled subsidiaries. (Note2) “Renesas Electronics product(s)” means any product developed or manufactured by or for Renesas Electronics. (Rev.5.0-1 October 2020) Corporate Headquarters Contact information TOYOSU FORESIA, 3-2-24 Toyosu, Koto-ku, Tokyo 135-0061, Japan www.renesas.com Fo r further information on a product, technology, the most up-to-date version of a document, or your nearest sales office, please visit: www.renesas.com/contact/. Trademarks Renesas and the Renesas logo are trademarks of Renesas Electronics Corporation. All trademarks and registered trademarks are the property of their respective owners.