PS9715

PS9715 NEC | Alldatasheet

Document overview

• Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
• PDF pages: 6

Technical content

FEATURES

• HIGH COMMON MODE TRANSIENT IMMUNITY CMH, CML = ±20 kV/µs TYP
• SMALL AND THIN PACKAGE 5-pin SOP
• HIGH SPEED

10 Mbps

• PULSE WIDTH DISTORTION |tPHL – tPLH| = 7 ns TYP
• HIGH ISOLATION VOLTAGE BV = 2500 Vr.m.s.
• TOTEM POLE OUTPUT No pull-up resistor required
• AVAILABLE IN TAPE AND REEL PS9715-F3, F4: 3500 pcs/reel

DESCRIPTION

PS9715 is an optically coupled high-speed, totem pole output isolator containing a GaAIAs LED on the light emitting side (input side) and a photodiode and a signal processing circuit on the light receiving side (output side) on one chip. PS9715 HIGH CMR, 10 Mbps TOTEM POLE OUTPUT TYPE 5-PIN SOP PHOTOCOUPLER

APPLICATIONS

• LAN/FA
• MEASUREMENT EQUIPMENT
• PDP California Eastern Laboratories ELECTRICAL CHARACTERISTICS (TA = 0 to +85°C, Unless otherwise specified) PART NUMBER PS9715 SYMBOL PARAMETERS UNITS MIN TYP 1 MAX VF Forward Voltage, IF = 10 mA, TA = 25°CV 1.4 1.65 1.9 IR Reverse Current, VR = 3 V, TA = 25°C µA1 0 Ct Capacitance, V = 0, f = 1 MHz, TA = 25°Cp F 3 0 IOH High Level Output Current2 µA 0.003 200 Vcc = VO = 5.5 V, VF = 0.8 V VOH High Level Output Voltage V 2.4 3.0 Vcc = 4.5 V, IF = 250 µA, IOH = -2 mA VOL Low Level Output Voltage V 0.25 0.6 Vcc = 4.5 V, VF = 0.8 V, IOL = 8 mA ICCH High Level Supply Current, VCC = 5.5 V, IF = 0 mA mA 12 17 ICCL Low Level Supply Current, VCC = 5.5 V, IF = 10 mA mA 13 18 IOSH High Level Output Short Circuit Current, VCC = 5.5 V, VO = GND mA -26 IF = 0 mA, 10 ms or less IOSL Low Level Output Short Circuit Current, VCC = 5.5 V, VO = GND mA 34 IF = 8 mA, 10 ms or less IFHL Threshhold Input Current, High → Low, VCC = 5 V TA = 25°Cm A 2.3 5 RI-O Isolation Resistance, VI-O = 1 k VDC, RH = 40 to 60%, TA = 25°C Ω 1011 CI-O Isolation Capacitance, V = 0, f = 1 MHz, TA = 25°Cp F 0.4 tPHL Propagation Delay Time1, High → Low TA = 25°Cn s 1 5 3 3 6 5 VCC = 5 V, IF = 7.5 mA 10 85 tPLH Propagation Delay Time1, Low → High TA = 25°Cn s 1 5 4 0 6 5 VCC = 5 V, IF = 7.5 mA 10 85 Diode Detector Coupled Continued on next page PS9715

ELECTRICAL CHARACTERISTICS (TA = 0 to +85°C, Unless otherwise specified), Continued PART NUMBER PS9715 SYMBOL PARAMETERS UNITS MIN TYP MAX | tPHL – tPLH | Pulse Width Distortion, (PWD)3, VCC = 5 V, IF = 7.5 mA ns 7 50 CMH Common Mode Transient Immunity at High Level Output4, kV/µs1 0 2 0 VCC = 5 V, TA = 25°C, IF = 0 mA, VO (MIN) = 2 V, VCM = 1 kV CML Common Mode Transient Immunity at Low Level Output4, kV/µs1 0 2 0 VCC = 5 V, TA = 25°C, IF = 7.5 mA, VO (MAX) = 0.8 V, VCM = 1 kVCoupled Notes: 1. Typical values at T A = 25°C. 2. Because a high level output current (I OH) of 300 µA or more may be output when the temperature is 0°C or less and when VCC is around 3 to 4 V, it is important to confirm the characteristics (operation with the power supply on and off) during design, before using the device. 3. Test Circuit for Propagation delay time 4.Test Circuit for common mode transient immunity ABSOLUTE MAXIMUM RATINGS1 (TA = 25°C) SYMBOLS PARAMETERS UNITS RATINGS Diode IF Forward Current mA 30 VR Reverse Voltage V 5 Detector VCC Supply Voltage V 7 VO Output Voltage V 7 IOH High level Output Current2 mA -5 IOL Low level Output Current2 mA 13 PC Power Dissipation2,3 mW 130 Coupled BV Isolation Voltage 4 Vr.m.s. 2500 TOP Operating Temperature °C -40 to +85 TSTG Storage Temperature °C -55 to +125 Notes: 1. Operation in excess of any one of these parameters may result in permanent damage. 2. T A = -40 to +85°C, Applies to output pin Vo and power supply pin VCC. RECOMMENDED OPERATING CONDITIONS PART NUMBER PS9715 SYMBOLS PARAMETERS UNITS MIN TYP MAX IFH High Level Input Current mA 7.5 12.5 IFL Low Level Input Current µA0 2 5 0 VCC Supply Voltage V 4.5 5.0 5.5 N TTL(loads) 3 TA Operating Temperature °C0 +85 USAGE CAUTIONS 1. This device is ESD sensitive. 2. Bypass capacitor of more than 0.1 µF is used between V CC and GND near device. Also, ensure that the distance between the leads of the photocoupler and capactor is no more than 10 mm. Input Output 1.5 V VOH VOL tPHL tPLH IF (ON) 50% IF (ON) CL includes probe and stray wiring capacitance. Pulse input (IF) VO (monitor) Input (monitor) (PW = 500 ns, Duty cycle = 1/2) 47 Ω VCC = 5 V 0.1 Fµ CL = 30 pF 2.5 kΩ 1.3 kΩ VCC = 5 V 90% 10% 1 kV 0 V VOH 2 V 0.8 V VOL VCM VO (IF = 0 mA) VO (IF = 7.5 mA) tr tf CL includes probe and stray wiring capacitance. VO (Monitor) VCC = 5 V 0.1 Fµ CL = 15 pF SW IF VCM 4. AC voltage for 1 minute at TA = 25 °C, RH = 60% between input and output.

TYPICAL PERFORMANCE CURVES (TA = 25°C) MAXIMUM FORWARD CURRENT vs. AMBIENT TEMPERATURE DETECTOR POWER DISSIPATION vs. AMBIENT TEMPERATURE SUPPLY CURRENT vs. AMBIENT TEMPERATURE HIGH LEVEL OUTPUT VOLTAGE vs. AMBIENT TEMPERATURE PROPAGATION DELAY TIME, PULSE WIDTH DISTORTION vs. AMBIENT TEMPERATURE FORWARD CURRENT vs. FORWARD VOLTAGE Ambient Temperature, TA (°C) Maximum Forward Current, I F (mA) Detector Power Dissipation, P C (mW Ambient Temperature, TA (°C) Ambient Temperature, TA (°C) Forward Curren, I F (mA) Forward Voltage, VF (V) High Level Supply Current, I CCH (mA) LowLevel Supply Current, I CCL (mA) Ambient Temperature, TA (°C) Ambient Temperature, TA (°C) Propagation Delay Time,t PHL , t PLH (ns) Pulse Width Distortion, |t PHL PLH | (ns) High Level Output Voltage, VOH (V) 20 40 60 80 1000 85 20 40 60 80 85 1000 100 150 1.0 0.01 0.1 100 TA = +85˚C +50˚C +25˚C 0˚C –25˚C –50 –25 0 25 50 75 100 ICCL (IF = 10 mA) VCC = 5.5 V ICCH (IF = 0 mA) –50 –25 0 25 50 75 100 VCC = 4.5 V, VF = 0.8 V, IOH = 2.0 mA –50 –25 0 25 50 75 100 tPLH tPHL PWD PS9715

TYPICAL PERFORMANCE CURVES (TA = 25°C) PS9715 0.2 0.1 0.3 0.4 0.5 –50 –25 0 25 50 75 100 VCC = 4.5 V, IF = 7.5 mA, IOL = 8.0 mA VCC = 5.0 V –50 –25 0 25 50 75 100 2.5 7.5 51 0 12.513 VCC = 4.5 V, IF = 5.0 mA 0.2 0.1 0.3 0.4 0.5 TA = 85˚C 0˚C 25˚C VCC = 4.5 V, VF = 0.8 VTA = 85˚C 25˚C 0˚C VCC = 4.5 V, IF = 250 µATA = 85˚C 0˚C 25˚C LOW LEVEL OUTPUT VOLTAGE vs. AMBIENT TEMPERATURE LOW LEVEL OUTPUT VOLTAGE vs. AMBIENT TEMPERATURE LOW LEVEL OUTPUT VOLTAGE vs. LOW LEVEL OUTPUT CURRENT HIGHLEVEL OUTPUT VOLTAGE vs. HIGHLEVEL OUTPUT CURRENT HIGH LEVEL OUTPUT VOLTAGE vs. HIGH LEVEL OUTPUT CURRENT PROPAGATION DELAY TIME, PULSE WIDTH DISTORTION vs. FORWARD CURRENT Ambient Temperature, TA (°C) Low Level Output Voltage, V OL (V) Low Level Output Voltage, V OL (V) Ambient Temperature, TA (°C) Low Level Output Voltage, V OL (V) Low Level OututCurrent, IOL (mA) High Level Output Voltage, V OH (V) High Level OututCurrent, IOH (mA) High Level Output Voltage, V OH (V) High Level OututCurrent, IOH (mA) 51 01 52 02 5 30 TA = 25˚C, VCC = 5 V tPHL tPLH PWD Propagation Delay Time,t PHL , t PLH (ns) Pulse Width Distortion, |t PHL PLH | (ns) Forward Current, IF (mA)

TAPING SPECIFICATIONS (Units in mm) REEL OUTLINE AND DIMENSIONS Packing : 3500 pcs/reel TAPE OUTLINE AND DIMENSIONS TAPE DIRECTION PS9715-F3 PS9715-F4 PS9715 OUTLINE DIMENSIONS (Units in mm) PS9715 1.27 0.1±0.1 2.1±0.2 4.4 7.0±0.3 0.5±0.3 0.15+0.10 –0.05 4.0±0.5 1. Anode 2. Cathode 3. GND 4. V O 5. VCC TOP VIEW MARKING No. 1 pin Mark 9715 N003 Rank Code Year Assembled (Last 1 Digit) Week Assembled N 0 03 Assembly Lot 4.0±0.1 2.0±0.05 1.5 8±0.1 1.55±0.1 12±0.2 5.5±0.05 1.75±0.1

2.9 MAX

0.3 7.4±0.1 +0.1 4.6±0.1 2.4±0.1 φ 330±2.0 φ100±1.0 φ13.0±0.2 2.0±0.5 1.5 ± 0.1 φ13.0±0.2 R1.0 φ21.0±0.8 2.0±0.5 11.9 to 15.4 Outer edge of flange 13.5±1.0 17.5±1.0

EXCLUSIVE NORTH AMERICAN AGENT FOR NEC RF, MICROWAVE & OPTOELECTRONIC SEMICONDUCTORS CALIFORNIA EASTERN LABORATORIES • Headquarters • 4590 Patrick Henry Drive • Santa Clara, CA 95054-1817 • (408) 988-3500 • Telex 34-6393 • FAX (408) 988-0279 Internet: http://WWW.CEL.COM 06/26/2002 DATA SUBJECT TO CHANGE WITHOUT NOTICE Life Support Applications These NEC products are not intended for use in life support devices, appliances, or systems where the malfunction of these products can reasonably be expected to result in personal injury. The customers of CEL using or selling these products for use in such applications do so at their own risk and agree to fully indemnify CEL for all damages resulting from such improper use or sale. PS9715 Time (s) Package Surface Temperature T (˚C) 60 to 120 s s (preheating) (heating) to 10 s to 30 s 235˚C (peak temperature) 210˚C 100 to 160°C RECOMMENDED SOLDERING CONDITIONS (3) Cautions

• Fluxes Avoid removing the residual flux with freon-based and chlorine-based cleaning solvent. (1) Infrared reflow soldering
• Peak reflow temperature 235 ˚C or below (package surface temperature)
• Time of temperature higher than 210 ºC 30 seconds or less
• Number of reflows Three
• Flux Rosin flux containing small amount of chlorine (The flux with a maximum chlorine content of 0.2 Wt % is recommended.)