PS77 3M | Alldatasheet

Document overview

  • Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
  • PDF pages: 3

Technical content

Updated :February 2010 Supersedes : September 2008 Product Description Scotch-Weld PS77 is a single component, medium strength, anaerobic pipe sealant. PS77 is a thixotropic pipe sealant that cures quickly on steel pipes. Scotch-Weld PS77 cures when confined in the absence of air between close-fitting metal surfaces. Key Features Scotch-Weld PS77 is formulated to lock and seal medium to coarse straight and tapered pipe threads on pipes of diameter from 15mm to 80mm. PS77 prevents vibration loosening and leakage through the pipe threads. PS77 is formulated to give medium strength break torque, but lower prevail torque on assembled joints, thus enabling easier disassembly and servicing. Pipe joints made with PS77 should be fully torqued up within a maximum of 15 minutes from initial assembly. PS77 will give a rapid low pressure seal (after 20 mins). Physical Properties Chemical Type Dimethacrylate Appearance Fluorescent Yellow Specific Gravity 1.12 Viscosity cPs (Brookfield RVT spindle 5, 2.5rpm) Range 35,000 – 60,000 Typical Value 48,000 Viscosity cPs (Brookfield RVT spindle 5, 20rpm) Range 10,000 – 20,000 Typical Value 15,000 Performance Characteristics Maximum Gap Fill 0.25mm Fixture Time 15mins Full Cure 24hrs Strength Build Up 15 mins = Finger tight 1 hours = ~40% strength 24hours = 100% strength Breakaway Torque N.m (10964) Range 8-18 Typical 16 Prevail Torque N.m (10964) Range 2-10 Typical 4.5 Service Temperature Range -50 to +150ºC

Scotch-Weld Pipe Sealant PS77 February 2010 Additional Product Information Anaerobic adhesives only cure in the absence of air and with metal part activation. Adhesive outside the joint will remain uncured and may be wiped away with a cloth. PS77 is suitable for most straight and tapered pipe threads of medium to coarse pitch, for pipe diameters from 15mm to 80mm. PS77 will not cure outside the joint and is virtually non-fouling in most types of pipe systems. PS77 is not recommended on certain plastics as stress cracking can sometimes result. Some anti-corrosion chemicals inhibit the cure system in this type of anaerobic. Trials are recommended to establish whether cleaning of the parts in necessary. AC64 Activator may be required on plated parts. Application Techniques Ensure parts are clean, dry and free from oil and grease. Apply adhesive to all engaged threads, although to minimise excess adhesive inside the joint, apply adhesive only to the male part, leaving the first two threads clear. Assemble parts and allow to cure. Wipe excess adhesive from outside of joint. Heating the assembled parts accelerates the curing process. AC64 Activator may be used to accelerate cure and should be used if the application temperature is below 5ºC. The use of an accelerator may reduce the final bond strength by up to 30% Storage Conditions Keep the adhesive in a cool, dry place away from direct sunlight. Under such conditions shelf life at room temperature will be 12 months. Refrigeration to 5◦C gives optimum storage stability. Shelf Life 12 months from date of despatch by 3M when stored in the original carton at 21°C Precautionary Information Refer to product label and material Safety Data Sheet for health and safety information before using the product. For information please contact your local 3M Office………… www.3M.com For Additional Information To request additional information or to arrange for sales assistance, please see below for contact details. Important Notice All statements, technical informati on and recommendations contained in this document are based upon tests or experience that 3M believes are reliable. However, many factors beyond 3M’s control can affect the use and performance of a 3M product in a particular application, including the cond itions under which the product is used and the time and environmental conditions in which the product is expected to perform. Since these factors are uniquely within the user’s knowledge and control, it is essential that the user evaluate the 3M product to determine whether it is fit for a particular purpose and suitable for the user’s method or application. All questions of liability relating to this product are governed by the terms of the sale subject, where applicable, to the prevailing law Values pres ented have been determined by standard test methods and are average values not to be used for specification purposes. Our recommendations on the use of our products are based on tests believed to be reliable but we would ask that you conduct your own tests to determine their suitability for your applications. This is because 3M cannot accept any responsibility or liability direct or consequential for loss or damage caused as a result of our recommendations Note 3M and Scotch-Weld are trademarks of the 3M Company.

Scotch-Weld Pipe Sealant PS77 February 2010 3M Svenska AB Industri Bollstanäsvägen 3 191 89 Sollentuna Tel: 08-92 21 00 Fax: 08-92 22 88 E-post: kundservice@mmm.com www.3M.se/lim 3M a/s Industri Hannemanns Allé 53

2300 København S

Tlf.: 43 48 01 00 Fax.: 43 20 15 65 E-mail: dkindustri@mmm.com www.3Mindustri.dk 3M Norge AS Avd. Industri Hvamveien 6

2013 Skjetten

Tel: 0 63 84 Fax: 63 84 17 88 E-post: Kundeservice@mmm.com www.3M.no/lim Suomen 3M Oy Teollisuustuotteet PL 600 Keilaranta 6

02151 Espoo

Puh: 09-525 21 Fax: 09-525 2279 http://www.3M.fi/teollisuus