PR502 SELEC | Alldatasheet

Document overview

  • PDF pages: 2

Technical content

PR502 Advanced, Full Featured Profile Controller Features: « Indepth Ramp / Soak Control © Dual Display, 4 digit, 7 segment LED « LED Status Indicator: Relay ON, Tune, Alarm, Manual ¢ 4 Front Panel Control buttons TC/RTD Input, Analog Input © ON/OFF, PID, PID Autotune © °C/°F Selectable

10 Programs, 16 Steps Each

¢ Alarm at Each Step « Memory Retention © Two Setpoints Size: 1/16 DIN 48mm x 48mm Certifications: CE AL. Technical Specifications Display Functional Specifications: Digits 4 digit 7 Segment LED, Dual display Control Action 1) PID Height of Upper Display : 0.3785" 2) ON-OFF Helght of Lower Display : 0.2720" Proportional Band (P) 0.0 to 400.0° LED Indications Relay ON, Alarm, Manual mode, Tune Integral Time (|) 0 to 3600 sec Derivative Time (D) 0 to 200 sec Input Specifications afar (ia Thermocouple (J,K.TR,S,C,6,8,N,LU.W, Modes pene hah, Deviation low, Band, Full scale Platinel Il), RTD (Pt100) high, Full scale low, Sensor break DC Analog Inputs (-5 to S6mV, 0 to 10V, Operation Absolute / Deviation mode 0 to 20mA) Hysteresis Programmable Sampling time 200 ms Hold / Standby mode Programmable Input Filter (FTC) 0.2 to 10.0 sec Annuniator Programmable Resolution 1/0.1°for TC/RTD only Reset Action Programmable - Automatic or Latched ( Fixed 1° resolution for R & S type TC) Probe Break Action Upscale Decimal point position selectable: ' 1/0.1/0.01/0.001 for analog input Profile Temperature Unit °C/"F Selectable No. of Profiles 10 Indication Accuracy ForTC inputs: 0.25% of FS. #1” No. of Steps 16 each For R & S type TC inputs: 0.5% of FS. +2° Ramp/Soak Time Range 0.01 to 99.59 Hrs : Min (20 min of warm up time for TC inputs) Target Temperature Range SPL to SPHL. ore a oer oman Other Profile Parameters Link profiles, Programmable repeat cycle, es ar eet 20.0%, = Cig Power down resume / Reset options, Deviation (FE, True) hold, Alarm at each step with settable atarm duration Output Specifications Control 1 Supply Voltage Contact Rating (SPST) 5A @ 230V AC / 30V DC, resistive Supply Voltage 85 to 270V AC/DC (50 / 60Hz) SSR Drive (Voltage Pulse) 18V DC, 20mA Optional - 24V AC/DC, +10% Corer 0/4 to. 20mA DC Power Consumption 6VA max @230V AC (loop impedence:500Q max.) Voltage Oto 5/10V DC Environmental Specifications (load resistance :10KQ min.) Peer Temperature Operating: 0 to 50°C (32 to 122°F) Alarm 1 Storage: -20 to 75°C (-4 to 167°F) Contact Rating (SPST) 5A @ 230V AC / 30V DC, resistive Humidity (non-condensing) 95% RH SSR Drive 12V DC (20mA) Weight 170 gms Protection Level IP65 for faceplate Ld

PR502 Advanced, Full Featured Profile Controller Compliance Ordering Information IEC/EN 61326 (EMVEMC) This product is CE certified. Also available with UL marking against order. IEC/EN 61010 Revision3 2010 Edition (Safety) Please order as per the requirement. UL 61010 Revision3 2010 Edition (Safety) fe Dimensions me | Panel Cutout PR502-0-0-0 RELAY RELAY 85-270V AC/DC g + a € &|| | 2 g PR502-0-0-1 RELAY RELAY Yes 85-270V AC/DC PR502-0-1-1 RELAY 12VDC SSR Yes 85-270V AC/DC 48mm. 100mm 46mm 10mm PR502-0-1-0 RELAY 12VDC SSR 85-270V AC/DC Mounting Accessories (Supplied with units) PR502-1-0-1 18VDC SSR RELAY Yes 85-270V AC/DC

48 X 48 Collar clamp ‘ACL4802 PR502-1-0-0 18VDC SSR RELAY 85-270V AC/DC

PR502-1-1-0 18VDCSSR —_12VDC SSR 85-270V AC/DC Input Ranges (For TC/RTD input) PR502-1-1-1 18VDCSSR_—‘12VDC SSR Yes 85-270V AC/DC Resolution Ranges | PR5O2-2-0-0 4-20mA (Current) RELAY 85-270V ACIDC 1 04 PR502-2-0-1 4-20mA (Current) RELAY Yes 85-270V AC/DC c “150 to 850 -150 to 850 pr00 * 238 to 1562 “199 to 999 PR502-3-0-0 0-10V (Voltage) RELAY 85-270V AC/DC c -199 to 750 ~199 to 750 PR502-3-0-1 0-10V (Voltage) RELAY Yes 85-270V AC/DC J i ee eee a -328 to 1382 -199 to 999 © -499 to 1350 199 to 999 UL approved part numbers (with c¢ W... mark) K Please add suffix-CU to the above part nos.: * -328 to 2462 ~199 to 999 ie 1) PR502-0-0-0-CU ; ic -199 to 400 -199 to 400 oc, a -828 to 750 -199 to 750 © Oto 1750 WA Accessories ( Optional ) R&S ‘Standard SELEC accessories that can be used with this product. a 32 to 3182 WA ‘Adapter plate 1) AP7248 : Plastic adapter plate, used to mount 1/16 DIN (cutout size 48 x 48) Terminal Connections Instrument into existing (72 x 72) cutout size. 2) AP9648 : Plastic adapter plate, used to mount 1/16 DIN (cutout size 48 x 48) F Instrument into existing (96 x 96) cutout size. t ol) asiss ON 3) AP4896-4848-G-C : Plastic adapter plate, used to mount 1/16 DIN Noo! ion (cutout size 48 x 48) Instrument into existing (48 x 96) + 2 = @ ay f cutout size. - 8 Noi||52 ware comi ie) as wo SAA ,, Cable Size (AWG): 16-13 ; Stud Hole for Lug (inch): 0.137 ; Tightening Torque (Lb-inch): 7 [ES Cable Size (mm’): 1.5-2.5 ; Stud Hole for Lug (mm): 3.5 ; Tightening Torque (N-m): 0.8