PPG312F

PPG312F DATADELAY | Alldatasheet

Document overview

• Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
• PDF pages: 5

Technical content

Doc #97008 DATA DELAY DEVICES, INC. 1/15/97 3 Mt. Prospect Ave. Clifton, NJ 07013 12-BIT PROGRAMMABLE PULSE GENERATOR (SERIES PPG312F)

FEATURES

Digitally programmable in 4096 steps Monotonic pulse-width-vs-address variation Rising edge triggered Two separate outputs: inverting & non-inverting Precise and stable pulse width Input & outputs fully TTL interfaced & buffered

10 T2L fan-out capability

Fits standard 40-pin DIP socket Auto-insertable FUNCTIONAL DESCRIPTION The PPG312F-series device is a 12-bit digitally programmable pulse generator. The width, PWA, depends on the address code (A11-A0) according to the following formula: PWA = PW0 + TINC * A where A is the address code, TINC is the incremental pulse width of the device, and PW0 is the inherent pulse width of the device. The incremental width is specified by the dash number of the device and can range from 0.5ns through 400ns, inclusively. RESET is held LOW during normal operation. When it is brought HIGH, OUT and OUT/ are forced into LOW and HIGH states, respectively, and the unit is ready for the next trigger input. The address is not latched and must remain asserted while the output pulse is active. SERIES SPECIFICATIONS Programmed pulse width tolerance: 5% or 2ns, whichever is greater Inherent width (PW0):20ns typical Inherent delay (TTO): 10ns ± 2ns Operating temperature: 0° to 70° C Supply voltage VCC: 5VDC ± 5% Supply current: ICC = 200ma typical 1997 Data Delay Devices data delay devices, inc. TRIG N/C N/C N/C N/C N/C N/C GND N/C N/C GND GND A10 A11 VCC N/C OUT OUT/ N/C RES N/C N/C VCC N/C N/C N/C N/C N/C N/C VCC PPG312F-xx DIP PPG312F-xxC5 Gull-Wing PPG312F-xxM Military DIP PPG312F-xxMC5 Military Gull-Wing PIN DESCRIPTIONS TRIG Trigger Input OUT Non-inverted Output OUT/ Inverted Output A0-A11 Address Bits RES Reset VCC +5 Volts GND Ground DASH NUMBER SPECIFICATIONS Part Number Incremental Width Per Step (ns) Total Width Change (us) PPG312F-.5 .5 ± .3 2.048 ± 0.10 PPG312F-1 1 ± .5 4.096 ± 0.20 PPG312F-2 2 ± .5 8.192 ± 0.41 PPG312F-5 5 ± 1.5 20.48 ± 1.02 PPG312F-10 10 ± 2.0 40.96 ± 2.05 PPG312F-20 20 ± 2.0 81.92 ± 4.10 PPG312F-50 50 ± 2.5 204.8 ± 10.2 PPG312F-100 100 ± 5.0 409.6 ± 20.5 PPG312F-200 200 ± 10.0 819.2 ± 41.0 PPG312F-400 400 ± 20.0 1,638.4 ± 81.9 NOTE: Any dash number between .5 and 400 not shown is also available.

Doc #97008 DATA DELAY DEVICES, INC. 1/15/97 Tel: 973-773-2299 Fax: 973-773-9672 http://www.datadelay.com APPLICATION NOTES DEVICE TIMING The timing definitions and restrictions for the PPG312F are shown in Figure 1. The unit is activated by a rising edge on the TRIG input. After a time, TTO (called the inherent delay), the rising edge of the pulse appears at OUT. The duration of the pulse is given by the above equation. For the duration of the pulse, the device ignores subsequent triggers. Once the falling edge of the pulse has appeared at OUT, an additional time, TOTR, is required before the device can respond to the next trigger. At power-up, the state of the PPG312F is unknown. Consequently, after power is applied, the unit may not respond to input triggers for a time equal to the maximum pulse width, PWT. After this time, the unit will function properly. If your application requires that the device function immediately, issue a quick reset at power-up. POWER SUPPLY BYPASSING The PPG312F relies on a stable power supply to produce repeatable pulses within the stated tolerances. A 0.1uf capacitor from VCC to GND, located as close as possible to each VCC pin, is recommended. A wide VCC trace should connect all VCC pins externally, and a clean ground plane should be used. INCREMENT TOLERANCES Please note that the increment tolerances listed represent a design goal. Although most increments will fall within tolerance, they are not guaranteed throughout the address range of the unit. Monotonicity is, however, guaranteed over all addresses. TOAX TRTS TTW TTO PWA A11-A0 RES TRIG OUT OUT/ Figure 1: Timing Diagram A i Ai+1 TSKEW TATS TRO TOTR TTW TRW

Doc #97008 DATA DELAY DEVICES, INC. 1/15/97 3 Mt. Prospect Ave. Clifton, NJ 07013 DEVICE SPECIFICATIONS TABLE 1: AC CHARACTERISTICS PARAMETER SYMBOL MIN TYP MAX UNITS Total Programmable Pulse Width PWT 4095 TINC Inherent Pulse Width PW0 15.0 20.0 27.0 ns Trigger to Output Delay TTO 8.0 10.0 12.0 ns Reset to Output Delay TRO 17.0 ns Output Skew TSKEW 1.5 ns Trigger Pulse Width TTW 5.0 ns Reset Pulse Width TRW 10.0 ns Reset to Trigger Setup Time TRTS 9.0 ns Address to Trigger Setup Time TATS 6.0 ns Output Low to Address Change TOAX 0.0 ns Output to Trigger Recovery Time TOTR 10.0 ns TABLE 2: ABSOLUTE MAXIMUM RATINGS PARAMETER SYMBOL MIN MAX UNITS NOTES DC Supply Voltage VCC -0.3 7.0 V Input Pin Voltage VIN -0.3 VDD+0.3 V Storage Temperature TSTRG -55 150 C Lead Temperature TLEAD 300 C 10 sec TABLE 3: DC ELECTRICAL CHARACTERISTICS (0C to 70C, 4.75V to 5.25V) PARAMETER SYMBOL MIN TYP MAX UNITS NOTES High Level Output Voltage VOH 2.5 3.4 V VCC = MIN, IOH = MAX VIH = MIN, VIL = MAX Low Level Output Voltage VOL 0.35 0.5 V VCC = MIN, IOL = MAX VIH = MIN, VIL = MAX High Level Output Current IOH -1.0 mA Low Level Output Current IOL 20.0 mA High Level Input Voltage VIH 2.0 V Low Level Input Voltage VIL 0.8 V Input Clamp Voltage VIK -1.2 V VCC = MIN, II = IIK Input Current at Maximum Input Voltage IIHH 0.1 mA VCC = MAX, VI = 7.0V High Level Input Current IIH µA VCC = MAX, VI = 2.7V Low Level Input Current IIL -0.6 mA VCC = MAX, VI = 0.5V Short-circuit Output Current IOS -60 -150 mA VCC = MAX Output High Fan-out Unit Output Low Fan-out 12.5 Load

Doc #97008 DATA DELAY DEVICES, INC. 1/15/97 Tel: 973-773-2299 Fax: 973-773-9672 http://www.datadelay.com PACKAGE DIMENSIONS 2.100 MAX. .320 MAX. .015 TYP. .070 MAX. .018 TYP. .580 MAX. .650 MAX. .010 ±.002 Lead Material: Nickel-Iron alloy 42 TIN PLATE .100 TYP. DIP (PPG312F-xx, PPG312F-xxM) 2.080±.020 .882 ±.005 .020 TYP. .040 TYP. .100 .090 1.100 .320 MAX. .590 MAX. .010±.002 .050 ±.010 .710 ±.005 .007 ±.005 Gull-Wing (PPG312F-xxC5, PPG312F-xxMC5)

Doc #97008 DATA DELAY DEVICES, INC. 1/15/97 3 Mt. Prospect Ave. Clifton, NJ 07013 DELAY LINE AUTOMATED TESTING TEST CONDITIONS INPUT: OUTPUT: Ambient Temperature: 25oC ± 3oC Load:

1 FAST-TTL Gate

Supply Voltage (Vcc): 5.0V ± 0.1V Cload: 5pf ± 10% Input Pulse: High = 3.0V ± 0.1V Threshold: 1.5V (Rising & Falling) Low = 0.0V ± 0.1V Source Impedance: 50Ω Max. Rise/Fall Time: 3.0 ns Max. (measured between 0.6V and 2.4V ) Pulse Width: PWIN = 10ns Period: PERIN = 2 x Max. Pulse Width NOTE: The above conditions are for test only and do not in any way restrict the operation of the device. OUT OUT TRIG IN REF TRIG Test Setup DEVICE UNDER TEST (DUT) TIME INTERVAL COUNTER PULSE GENERATOR COMPUTER SYSTEM PRINTER IN Timing Diagram For Testing TTO PWA PERIN PWIN TRISE TFALL 0.6V 0.6V 1.5V 1.5V 2.4V 2.4V 1.5V 1.5V VIH VIL VOH VOL INPUT SIGNAL OUTPUT SIGNAL