PMP122

PMP122 TTELEC | Alldatasheet

Document overview

• Manufacturer or author: Provided By alldatasheet.com(free datasheet download site)
• PDF pages: 4

Technical content

© TT Electronics plc General Note All data sheets are subject to change without noƟce. PROTEK POWER: PMP122 Rev 0 10 December 2021 Page: 1 TT Electronics hƩp://www.Ʃelectronics.com/power‐supplies Features: DescripƟon: *Safety approvals may be model dependent. Consult TT Electronics for specifics or for additional safety approvals required.  OperaƟng alƟtude up to 5000m  PFC circuit  Wide input range 80 ‐ 264VAC  OpƟonal output connectors  Over‐voltage/over‐temperature/over‐current protecƟon  Meets EU CoC EPS V5 Tier 2  No Load power consumpƟon ≤0.15W The PMP122 series of AC/DC switching power supplies provide 96 ‐ 120 waƩs of conƟnuous power. They are available as Class I or Class II input devices with IEC320 C14, C6, C8, or C18 inlets enclosed in a 94V‐0 rated polycarbonate case which mates with an interchangeable cord for world‐wide use. All models meet FCC PART 15 and EN55011 Class B emissions limits, EN61000, and comply with IEC60601 standards. These power supplies are designed for medical applicaƟons. Model Voltage Current Total Power Load RegulaƟon Line RegulaƟon Ripple & Noise (P‐P) PMP122‐12 12V 8.00A 96W ±5% ±0.5% 120mV PMP122‐13 15V 7.00A 105W ±5% ±0.5% 150mV PMP122‐13‐1 18V 6.67A 120W ±5% ±0.5% 180mV PMP122‐18 48V 2.5A 120W ±5% ±0.5% 480mV Notes: 1. Ripple & Noise is measured by using a 20MHz bandwid th limited oscilloscope and terminated with a 0.1µF ceramic capacitor in parallel with a 47µF aluminum electrolyƟc capacitor at full load and nominal line. 2. Line regula Ɵon is defined by changing input voltage ±10% from nominal line at rated load. 3. Standard for this series is the Cl ass I model with a IEC320 C14 inlet. To order a Class I model with a C6 inlet, add “S” to the prefix. e.g. PMP122S‐12. To order a Class II model with C18 inlet, add “F” in the prefix. eg. PMP122F‐12. To order a Class II model with C8 inlet, add “SF” to the prefix. e.g. PMP122SF‐12. PMP122‐13‐2 19V 6.32A 120W ±5% ±0.5% 190mV PMP122‐14 24V 5.00A 120W ±5% ±0.5% 240mV PMP122‐16 30V 4.00A 120W ±5% ±0.5% 300mV PMP122‐17 36V 3.34A 120W ±5% ±0.5% 360mV PMP122‐13‐3 20V 6.00A 120W ±5% ±0.5% 200mV

© TT Electronics plc General Note All data sheets are subject to change without noƟce. Rev 0 10 December 2021 Page: 2 TT Electronics hƩp://www.Ʃelectronics.com/power‐supplies SpecificaƟons: PROTEK POWER: PMP122 Input Input Voltage 90 ‐ 264VAC Input Frequency 47 ‐ 63Hz Input Current ≤1.60A at 115VAC ≤0.80A at 230VAC Inrush Current (Typical) ≤90A at 115VAC, cold start ≤180A at 230VAC, cold start No Load Power ConsumpƟon Meets DOE Level VI requirements Output Total Output Power See Table Output Voltage See Table Hold Up Time (Typical) ≥20mS at 100VAC, full load Turn on Delay ≤3S ProtecƟon Features Over‐voltage 112 ‐140%. Latching mode. Cycle power to reset. Over‐current Auto ‐recovery. Over‐temperature Latching mode. Cycle power to reset. Short Circuit Auto ‐recovery. Environmental OperaƟng Temperature 0° ‐ +60°C (See DeraƟng Curve) Storage Temperature ‐20° ‐ +85°C OperaƟng Humidity 10 ‐ 90% non‐condensing AlƟtude <5000m opera Ɵonal and storage

© TT Electronics plc General Note All data sheets are subject to change without noƟce. Rev 0 10 December 2021 Page: 3 TT Electronics hƩp://www.Ʃelectronics.com/power‐supplies SpecificaƟons (conƟnued): PROTEK POWER: PMP122 General SpecificaƟons Weight 1.21lb (550g) MTBF >100,000 hours per MIL ‐HDBK‐217F at full load and 25°C ambient AC Input Connector IEC320: C6, C8, C14, C18 DC Output Connector 4 pin plug without lock, maƟng with Kycon P/N KPJX‐4S‐S socket or equivalent. Safety Approvals* IEC60601 ‐1 UL, cUL, EN, CB, CE, TUV, UKCA *Safety approvals may be model dependent. Consult TT Electronics for specifics or for additional safety approvals required. EMC Conducted Emission Radiated Emission Harmonic Currents Voltage Flicker EN55011 Class B EN55011 Class B EN61000‐3‐2, Class A and D EN61000‐3‐3:2013 ElectrostaƟc Discharge Radiated Immunity EFT/Burst Surge Immunity Conducted Immunity Power Frequency MagneƟc Field Immunity Dips/InterrupƟons IEC61000‐4‐2:2008 (±15kV air, ±8kV contact) IEC61000‐4‐3:2006+A1:2007+A2:2010 (9 ‐ 28V/m) IEC61000‐4‐4:2012 (±2kV) IEC61000‐4‐5:2014/AMD1:2017 (±1kV diff, ±2kV com) IEC61000‐4‐6:2013 (10Vrms) IEC61000‐4‐8:2009 (3A/m) IEC61000‐4‐11:2004 (30% reducƟon for 500mS (criteria A at 230VAC, criteria B at 100VAC), 60% reducƟon for 100mS (criteria A at 230VAC, criteria B at 100VAC) and >95% reducƟon for 20mS)

© TT Electronics plc General Note All data sheets are subject to change without noƟce. Rev 0 10 December 2021 Page: 4 TT Electronics hƩp://www.Ʃelectronics.com/power‐supplies Mechanical Outline: PROTEK POWER: PMP122 DeraƟng Curves: Pin Chart: Notes: 1. Dimensions shown in inches [mm] 2. Tolerance 0.02 [0.5] maximum PIN NO. 1 2 3 4 Polarity V1 Return +V1 V1 Return +V1