DLW5BSN302SQ2L MURATA | Alldatasheet

Document overview

  • Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
  • PDF pages: 40

Technical content

!Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.

  • This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please review our product specifications or consult the approval sheet for product specifications before ordering.C31E.pdf Mar.28,2011

!Caution/Notice Soldering and Mounting Packaging Design Kits Chip Common Mode Choke Coil Large Current Common Mode Choke Coil for Automotive Available !Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.

  • This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please review our product specifications or consult the approval sheet for product specifications before ordering.C31E.pdf Mar.28,2011 Chip Ferrite BeadChip EMIFILrChip Common Mode Choke CoilBlock Type EMIFILr

!Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.

  • This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please review our product specifications or consult the approval sheet for product specifications before ordering.C31E.pdf Mar.28,2011 Chip Ferrite BeadChip EMIFILrChip Common Mode Choke CoilBlock Type EMIFILr 150 DLpSeries Introduction Common Mode Current Differential Mode Current Magnetic flux by common mode current is added each other and works as an inductor DLP11SA DLW21SN_HQ2 DLP0NS DLP11SN DLP2AD DLW21SN_SQ2 DLW31S DLW21H DLP31S DLP31D DLW5AH DLW5BS DLW5BT DLM11G DLM2HG High cut-off frequency High Coupling For high speed differential signal lines) Ultra high cut-off frequency for high speed differential signal lines High cut-off frequency for high speed differential signal lines for general differential signal lines Film type Film type Film type Wound type Wound type Wound type Multilayer type Large current High coupling (For power lines) Relative high differential mode impedance Low coupling (For audio lines)
  • Low profile, small size, suitable for mobile equipments.
  • Tight terminal pitch enables high density layout.
  • Ultra high cut-off frequency and its matching to line impedance enables good transmission of high speed signal.
  • Ultra high self resonance frequency enables high cut-off frequency.
  • Its matching to line impedance enables good transmission of high speed signal.
  • Low profile, small size, suitable for mobile equipments.
  • Tight terminal pitch enables high density layout.
  • High cut-off frequency enables good transmission of high speed signal.
  • Ultra high self resonance frequency enables high cut-off frequency.
  • DLW21H is designed as low profile.
  • Low profile,small size, suitable for mobile equipments.
  • Tight terminal pitch enables high density layout.
  • Large current (6A max.), suitable for input connector from an AC adaptor.
  • DLW5BT is designed as low profile.
  • Modified its differential mode impedance higher than other common mode choke coils, this feature makes possible to suppress both common mode and differential mode noise.
  • DLM11GN601SD2 is ideal to keep low distortion audio signal.
  • DLM2HG can meet stereo 3 lines which contain a ground line. Category Features, Classification Structure Part Number Comments PLT10HHWinding type Cased structure Large current Automotive Available (For power lines)
  • Large current, high reliability, suitable for mortors in automobile. Magnetic flux by differential mode current is canceled each other and do not works as an inductor Available up to 10A

!Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.

  • This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please review our product specifications or consult the approval sheet for product specifications before ordering.C31E.pdf Mar.28,2011 Chip Ferrite BeadChip EMIFILrChip Common Mode Choke CoilBlock Type EMIFILr 151 1000 1500 2000 2500 3000 3500 4000 4500 5000 Frequency (MHz) 1000 1500 2000 2500 3000 3500 4000 4500 5000 Frequency (MHz) DLW21SN900HQ2 DLP11SA900HL2 Noise Suppression Example Skew Improve Effect of Common Mode Choke Coil Example of Skew Improvement by Common Mode Choke Coil (Test using pulse generator waveform) Waveform is equivalent to 1000Mbps signal Waveform with intentionally made skew (skew: 100ps) Skew is improved by common mode choke coil Mechanism of Skew Improvement Waveform rises (or falls) Current change generates magnetic flux on a ferrite core Electromotive force is generated on another line This electromotive force works to decrease the delay of waveform Noise Suppression of Common Mode Choke Coil in HDMI Line Device under test / Transmitter : game machine Receiver : projector Cable / HDMI categoly2 3m cable Test resolution / 1080p Deep color 12bit (Data 1.11GHz) DVD play mode Without filter Without filter Test Example of HDMI1.3 Waveform Transmission ~Using ESD protection device 0.05pF~ Signal frequency : 1.11GHz (Deep color 12bit) CLOCK DATA Transition Time Rise time: 83.4ps Fall time: 77.4ps Rise time: 90.4ps Fall time: 85.5ps Rise time: 100ps Fall time: 97.4ps Video signal generator common mode choke coilESD protection device 0.05pF ESD protection device only Film Type DLP11SN900HL2 (Cut-off frequency is most low in the table below) Cut-off Frequency Judge Wound Type DLW21SN900HQ2 Film Type DLP11SA900HL2 Film Type Array DLP2ADN900HL4 Over 10GHz Around 6GHz Around 4GHz Specification satisfied Specification satisfied Specification satisfied Specification satisfied Each of common mode choke coil can keep waveform, satisfy the specification. Noise Level (dBµV/m) Noise Level (dBµV/m) DLP/DLW Series

!Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.

  • This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please review our product specifications or consult the approval sheet for product specifications before ordering.C31E.pdf Mar.28,2011 Chip Ferrite BeadChip EMIFILrChip Common Mode Choke CoilBlock Type EMIFILr 152 Part Numbering (Part Number) DLp t N y 371 q DL u S r S e 21 2 o! 0 L w W i Q Chip Common Mode Choke Coil eDimensions (LgW) Code 0.85g0.65mm 1.25g1.0mm 1.5g0.65mm 2.0g1.2mm 3.2g1.6mm 2.0g1.0mm 2.5g2.0mm 5.0g3.6mm 5.0g5.0mm Dimensions (LgW) 03025 0504 05025 0805 1206 0804 1008 2014 2020 EIA qProduct ID DL Chip Common Mode Choke Coils Product ID wStructure W M P Wire Wound Type Multilayer Type Film Type Code Structure tCategory A B N R Expressed by a letter. Code Category C S D H G T Magnetically Shielded One Circuit Type Magnetically Shielded Two Circuit Type Open Magnetic One Circuit Type Magnetically Monolithic Type (sectional winding) Magnetically Shielded One Circuit Low Profile Type Code Type !0Packaging K L B DLW5AH/DLW5BS/DLW5BT All Series All Series Embossed Taping (ø330mm Reel) Embossed Taping (ø180mm Reel) Bulk Code Packaging Series Two Lines Three Lines Four Lines Code Number of Signal Lines D L Q Z Expressed by a letter. Expressed by a letter. Code Features iFeatures (2) rFeatures (1) yImpedance Typical impedance at 100MHz is expressed by three figures. The unit is in ohm (Ω ). The first and second figures are significant digits, and the third figure expresses the number of zeros which follow the two figures. uCircuit S M H U Code Circuit oNumber of Signal Lines

!Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.

  • This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please review our product specifications or consult the approval sheet for product specifications before ordering.C31E.pdf Mar.28,2011 Chip Ferrite BeadChip EMIFILrChip Common Mode Choke CoilBlock Type EMIFILr 153 Part Numbering (Part Number) PL pCommon Mode Choke Coils eApplications qProduct ID PL Common Mode Choke Coils Product ID wType T DC Type Code Type 10H for DC Line High-frequency Type Code Applications tImpedance H for Automotive Code Features oPackaging B L K PLT10H PLT10H PLT10H Bulk Embossed Taping (ø 178mm/ø 180mm Reel) Embossed Taping (ø 330mm Reel) Code Packaging Series N No Lead Terminal (SMD) Aligned Winding Type Code Lead Dimensions iLead Dimensions rFeatures yRated Current Expressed by three figures. The unit is ampere (A). The first and second figures are significant digits, and the third figure expresses the number of zeros which follow the two figures. A decimal point is expressed by the capital letter "R". In this case, all figures are significant digits. Expressed by three figures. The unit is ohm (Ω ). The first and second figures are significant digits, and the third figure expresses the number of zeros which follow the two figures. uWinding Mode P Code Winding Mode t 102 r H y 6R0 q PL e 10H w T u P i N o B

!Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.

  • This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please review our product specifications or consult the approval sheet for product specifications before ordering.C31E.pdf Mar.28,2011 Chip Ferrite BeadChip EMIFILrChip Common Mode Choke CoilBlock Type EMIFILr 154 Part NumberType Size Code (Inch) Rated CurrentCommon Mode Impedance (at 100MHz/20°C) DLM11GN601SD20504 Thickness (mm) 0.5 1.2 0.45 0.45 0.45 0.45 0.82 0.82 0.82 0.82 0.82 0.82 0.82 0.82 0.82 0.82 0.82 1.15 1.15 1.15 0.82 0.82 0.82 0.82 0.82 0.82 0.82 0.82 0.82 0.82 1.15 1.15 1.15 1.15 1.15 1.2 1.2 1.2 1.2 1.2 1.2 1.2 1.2 1.2 1.2 0.9 0.9 0.9 0.9 1.9 1.9 1.9 1.9 1.9 1.9 1008 03025 0504 1206 0804 1206 0805 1206 Multilayer Type for Audio Lines Film Type for Differential Signal Lines Film Array Type for Differential Signal Lines Wire Wound Type for Differential Signal Lines 600ohm ±25% 100mA DLM2HGN601SZ3 600ohm ±25% 100mA DLP0NSN670HL2 DLP0NSC280HL2 DLP0NSA150HL2 67ohm ±20% 110mA 28ohm ±20% 100mA 0.45 15ohm ±5ohm 100mA DLP0NSN900HL2 90ohm ±20% 100mA DLP0NSN121HL2 120ohm ±20% 90mA DLP11SA350HL2 35ohm ±20% 170mA DLP11SA670HL2 67ohm ±20% 150mA DLP11SN670SL2 67ohm ±20% 180mA DLP11SA900HL2 DLP11TB800UL2 90ohm ±20% 150mA 0.3 80ohm ±25% 100mA DLP11SN900HL2 90ohm ±20% 150mA DLP11SN121SL2 120ohm ±20% 140mA DLP11SN161SL2 160ohm ±20% 120mA DLP11SN201HL2 200ohm ±20% 110mA DLP11SN241HL2 240ohm ±20% 100mA DLP11SN281HL2 280ohm ±20% 90mA DLP11SN331HL2 330ohm ±20% 80mA DLP31SN121ML2 120ohm ±20% 100mA DLP31SN221ML2 220ohm ±20% 100mA DLP31SN551ML2 550ohm ±20% 100mA DLP2ADN670HL4 DLP2ADA900HL4 DLP2ADA670HL4 DLP2ADA350HL4 DLP1NDN350HL4 DLP1NDN670HL4 DLP1NDN900HL4 67ohm ±20% 140mA 90ohm ±20% 120mA 67ohm ±20% 130mA 35ohm ±20% 150mA 0.45 35ohm ±20% 100mA 0.45 67ohm ±20% 80mA 0.45 90ohm ±20% 60mA DLP2ADN900HL4 90ohm ±20% 130mA DLP2ADN121HL4 120ohm ±20% 120mA DLP2ADN161HL4 160ohm ±20% 100mA DLP2ADN201HL4 200ohm ±20% 90mA DLP2ADN241HL4 240ohm ±20% 80mA DLP2ADN281HL4 280ohm ±20% 80mA DLP31DN900ML4 90ohm ±20% 160mA DLP31DN131ML4 130ohm ±20% 120mA DLP31DN201ML4 200ohm ±20% 100mA DLP31DN321ML4 320ohm ±20% 80mA DLP31DN441ML4 440ohm ±20% 70mA DLW21SN670SQ2 67ohm ±25% 400mA DLW21SN900SQ2 90ohm ±25% 330mA DLW21SN121SQ2 120ohm ±25% 370mA DLW21SN181SQ2 180ohm ±25% 330mA DLW21SN261SQ2 260ohm ±25% 300mA DLW21SN371SQ2 370ohm ±25% 280mA DLW21SN670HQ2 67ohm ±25% 320mA DLW21SN900HQ2 90ohm ±25% 280mA DLW21SN121HQ2 120ohm ±25% 280mA DLW21SR670HQ2 67ohm ±25% 400mA DLW21HN670SQ2 67ohm ±25% 330mA DLW21HN900SQ2 90ohm ±25% 330mA DLW21HN121SQ2 120ohm ±25% 280mA DLW21HN181SQ2 180ohm ±25% 250mA DLW31SN900SQ2 90ohm ±25% 370mA DLW31SN161SQ2 160ohm ±25% 340mA DLW31SN261SQ2 260ohm ±25% 310mA DLW31SN601SQ2 600ohm ±25% 260mA DLW31SN102SQ2 1000ohm ±25% 230mA DLW31SN222SQ2 2200ohm ±25% 200mA p158 p159 p160 p162 p163 p16405025 p165 p166 p168 p169 p171 p172 Continued on the following page. Chip Common Mode Choke Coil Series Line UpDLp

!Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.

  • This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please review our product specifications or consult the approval sheet for product specifications before ordering.C31E.pdf Mar.28,2011 Chip Ferrite BeadChip EMIFILrChip Common Mode Choke CoilBlock Type EMIFILr 155 Part NumberType Size Code (Inch) Rated CurrentCommon Mode Impedance (at 100MHz/20°C) Thickness (mm) 4.3 4.5 4.5 4.5 4.5 4.5 2.5 2.5 2.5 2.5 2.5 2020 2014 Wire Wound Type for Power Lines and Signal Lines DLW5BSN302SQ2 3000ohm(Typ.) 500mA DLW5AHN402SQ2 4000ohm(Typ.) 200mA DLW5BSN191SQ2 190ohm(Typ.) 5000mA DLW5BSN351SQ2 350ohm(Typ.) 2000mA DLW5BSN102SQ2 1000ohm(Typ.) 1500mA DLW5BSN152SQ2 1500ohm(Typ.) 1000mA DLW5BTN101SQ2 100ohm(Typ.) 6000mA DLW5BTN251SQ2 250ohm(Typ.) 5000mA DLW5BTN501SQ2 500ohm(Typ.) 4000mA DLW5BTN102SQ2 1000ohm(Typ.) 2000mA DLW5BTN142SQ2 1400ohm(Typ.) 1500mA p156 p156 p157 Part NumberType Size Rated Current Common Mode Impedance (at 10MHz/20°C) PLT10HH401100PN PLT10HH501100PN PLT10HH9016R0PN PLT10HH1026R0PN 400ohm 12.9x6.6 (mm) Thickness (mm) 9.4 9.4 9.4 9.4 Large Current Common Mode Choke Coil for Automotive Available 10A 500ohm 10A 900ohm 6A 1000ohm 6A p173 DL p Chip Common Mode Choke Coil Series Line Up Large Current Common Mode Choke Coil for Automotive AvailableSeries Line UpPLp

!Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.

  • This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please review our product specifications or consult the approval sheet for product specifications before ordering.C31E.pdf Mar.28,2011 Chip Ferrite BeadChip EMIFILrChip Common Mode Choke CoilBlock Type EMIFILr Universal Type [Power Lines/Signal Lines] 156 5A max, common mode choke coil for power lines. DLW5AH/DLW5BSSeries (2014/2020 Size) DLW Series Universal Type [Power Lines/Signal Lines] Chip Common Mode Choke Coil I Dimensions I Equivalent Circuit I Packaging I Dimensions I Equivalent Circuit I Packaging I Impedance-Frequency Characteristics (Main Items) I Rated Value (p: packaging code) I Derating of Rated Current DLW5AH DLW5BS DLW5BSN191 Refer to pages from p.176 to p.179 for mounting information. DLW5AH/DLW5BS Code Packaging Minimum Quantity L 180mm Reel Embossed Tape 400 K 330mm Reel Embossed Tape 1500 B Bulk(Bag) 100 Code Packaging Minimum Quantity L 180mm Reel Embossed Tape 400 K 330mm Reel Embossed Tape 1500 B Bulk(Bag) 100 DLW5BSN152SQ2 p 1500ohm(Typ.) 1000mA 50Vdc 10M ohm 125Vdc 0.1ohm max. DLW5BSN302SQ2 p 3000ohm(Typ.) 500mA 50Vdc 10M ohm 125Vdc 0.3ohm max. Operating Temperature Range: -25°C to +85°C (DLW5AH), -40°C to +85°C (DLW5BS) Number of Circuit: 1 Part Number Common Mode Impedance (at 100MHz/20°C) Rated Current Rated Voltage Insulation Resistance (min.) Withstand Voltage DC Resistance DLW5AHN402SQ2 p 4000ohm(Typ.) 200mA 50Vdc 10M ohm 125Vdc 3.0ohm max. DLW5BSN191SQ2 p 190ohm(Typ.) 5000mA 50Vdc 10M ohm 125Vdc 0.02ohm max. DLW5BSN351SQ2 p 350ohm(Typ.) 2000mA 50Vdc 10M ohm 125Vdc 0.04ohm max. DLW5BSN102SQ2 p 1000ohm(Typ.) 1500mA 50Vdc 10M ohm 125Vdc 0.06ohm max. (L) 5.0±0.3 (T) 4.3 max. (W) 3.6±0.3 0.5 min. 0.45 min. 1.7±0.3 (2)(1) (4) (3) 1.7±0.31.3±0.3 Starting position of wiring should be covered with resin.* * * (in mm) : Electrode (L) 5.0±0.3 (T) 4.5 max. 3.6±0.3 (W) 5.0±0.3 0.5 min. 0.45 min. 1.7±0.3 (2)(1) (4) (3) 1.7±0.3 1.3±0.3 0.9±0.3 * The marking to indicate the product direction can be applicable. (Optional) 1.3±0.3 (in mm) : Electrode Polarity Marking Impedance (Ω ) Frequency (MHz) 100000 10000 1000 100 1 10 100 1000 DLW5AHN402SQ2 DLW5BSN302SQ2 DLW5BSN152SQ2 DLW5BSN102SQ2 DLW5BSN351SQ2 DLW5BSN191SQ2 Common mode DLW5AHN402SQ2 DLW5BSN302SQ2 DLW5BSN152SQ2 DLW5BSN102SQ2 DLW5BSN351SQ2 DLW5BSN191SQ2Differential mode 4.5 4.75 0 1 02 03 04 05 06 07 08 0 75°C8 5 °C 90 100 Rated Current (A) Operating Temperature (°C) DLW5BSN191SQ2 Temperature Derating (1) (4) (2) (3) No polarity. (1) (4) (2) (3) No polarity.

!Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.

  • This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please review our product specifications or consult the approval sheet for product specifications before ordering.C31E.pdf Mar.28,2011 Chip Ferrite BeadChip EMIFILrChip Common Mode Choke CoilBlock Type EMIFILr Universal Type [Power Lines/Signal Lines] 157 Low profile wire-wound common choke coil for power lines. DLW5BTSeries (2020 Size) DLW Series Universal Type [Power Lines/Signal Lines] Chip Common Mode Choke Coil I Dimensions I Equivalent Circuit I Packaging I Impedance-Frequency Characteristics (Main Items) I Rated Value (p: packaging code) I Derating of Rated Current DLW5BTN101/251/501 Refer to pages from p.176 to p.179 for mounting information. DLW5BT Code Packaging Minimum Quantity L 180mm Reel Embossed Tape 700 K 330mm Reel Embossed Tape 2500 B Bulk(Bag) 100 Part Number Common Mode Impedance (at 100MHz/20°C) Rated Current Rated Voltage Insulation Resistance (min.) Withstand Voltage DC Resistance DLW5BTN101SQ2 p 100ohm(Typ.) 6000mA 50Vdc 10M ohm 125Vdc 0.009ohm±40% DLW5BTN251SQ2 p 250ohm(Typ.) 5000mA 50Vdc 10M ohm 125Vdc 0.014ohm±40% DLW5BTN501SQ2 p 500ohm(Typ.) 4000mA 50Vdc 10M ohm 125Vdc 0.019ohm±40% DLW5BTN102SQ2 p 1000ohm(Typ.) 2000mA 50Vdc 10M ohm 125Vdc 0.024ohm±40% DLW5BTN142SQ2 p 1400ohm(Typ.) 1500mA 50Vdc 10M ohm 125Vdc 0.040ohm±40% Operating Temperature Range: -40°C to +85°C Number of Circuit: 1 (L) 5.0±0.3 3.6±0.3 (W) 5.0±0.3 0.5 min. 0.45 min. 1.7±0.3 (2)(1) (4) (3) 1.7±0.3 1.3±0.3 0.9±0.3 * The marking to indicate the product direction can be applicable. (Optional) 1.3±0.3 (in mm) : Electrode Polarity Marking (T) 2.35±0.15 Impedance (Ω ) Frequency (MHz) 100 1000 10000 1 10 100 1000 Common mode DLW5BTN101SQ2 DLW5BTN251SQ2 DLW5BTN501SQ2 DLW5BTN102SQ2 DLW5BTN142SQ2 DLW5BTN101SQ2 DLW5BTN251SQ2 DLW5BTN501SQ2 DLW5BTN102SQ2 DLW5BTN142SQ2 Differential mode 1000 2000 3000 4000 5000 6000 7000 0 2 04 06 08 0 1 0 0 Current (mA) Temperature (°C) 4750 3400 (1) (4) (2) (3) No polarity.

!Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.

  • This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please review our product specifications or consult the approval sheet for product specifications before ordering.C31E.pdf Mar.28,2011 Chip Ferrite BeadChip EMIFILrChip Common Mode Choke CoilBlock Type EMIFILr Signal Lines Type 158 Audio line common choke also effective to differential mode. DLM11GSeries (0504 Size) DLM Series Signal Lines Type Chip Common Mode Choke Coil I Dimensions I Equivalent Circuit I Packaging I Impedance-Frequency Characteristics (Main Items) I Rated Value (p: packaging code) Refer to pages from p.176 to p.179 for mounting information. DLM11G Code Packaging Minimum Quantity D 180mm Reel Paper Tape 10000 B Bulk(Bag) 1000 Part Number Common Mode Impedance (at 100MHz/20°C) Rated Current Rated Voltage Insulation Resistance (min.) Withstand Voltage DC Resistance DLM11GN601SD2 p 600ohm ±25% 100mA 5Vdc 100M ohm 25Vdc 0.8ohm max. Operating Temperature Range: -40°C to +85°C Number of Circuit: 1 1.25±0.15 0.65±0.1 0.35±0.15 0.2±0.15 1.0±0.15 0.5±0.1 (2)(1) (3)(4) (in mm) : Electrode Impedance (Ω ) Frequency (MHz) 100 1000 10000 1 10 100 1000 Differential Mode Common Mode DLM11GN601SD2 DLM11GN601SD2 (1) (4) (2) (3) No polarity.

!Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.

  • This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please review our product specifications or consult the approval sheet for product specifications before ordering.C31E.pdf Mar.28,2011 Chip Ferrite BeadChip EMIFILrChip Common Mode Choke CoilBlock Type EMIFILr Signal Lines Type 159 3 line audio common mode choke coil. DLM2HGSeries (1008 Size) DLM Series Signal Lines Type Chip Common Mode Choke Coil I Dimensions I Equivalent Circuit I Packaging I Impedance-Frequency Characteristics (Main Items) I Rated Value (p: packaging code) Refer to pages from p.176 to p.179 for mounting information. DLM2HG Code Packaging Minimum Quantity L 180mm Reel Embossed Tape 3000 B Bulk(Bag) 1000 Part Number Common Mode Impedance (at 100MHz/20°C) Rated Current Rated Voltage Insulation Resistance (min.) Withstand Voltage DC Resistance DLM2HGN601SZ3 p 600ohm ±25% 100mA 16Vdc 100M ohm 100Vdc 0.40ohm max. Operating Temperature Range: -55°C to +85°C Number of Circuit: 1 0.3±0.2 2.0±0.2 1.2±0.2 2.5±0.2 0.4±0.2 0.8±0.1 (1) (3) (5) (2) (4) (6) (in mm) : Electrode Impedance (Ω ) Frequency (MHz) 10000 1000 100 1 10 100 1000 10000 Differential ModeDLM2HGN601SZ3 Common Mode DLM2HGN601SZ3 No polarity. (5)(3)(1) (6)(4)(2)

!Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.

  • This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please review our product specifications or consult the approval sheet for product specifications before ordering.C31E.pdf Mar.28,2011 Chip Ferrite BeadChip EMIFILrChip Common Mode Choke CoilBlock Type EMIFILr Signal Lines Type 160 03025 size, very small chip common mode choke coil, Cut-off frequency 3GHz max. DLP0NSSeries (03025 Size) DLP Series Signal Lines Type Chip Common Mode Choke Coil I Dimensions I Equivalent Circuit I Packaging I Impedance-Frequency Characteristics (Main Items) I Rated Value (p: packaging code) Refer to pages from p.176 to p.179 for mounting information. DLP0NS DLP0NSN 670/900/121 HL2 DLP0NSA150HL2/DLP0NSC280HL2 I Differential Mode Transmission Characteristics (Typ.) DLP0NSN900HL2 DLP0NSA150HL2 Code Packaging Minimum Quantity L 180mm Reel Embossed Tape 5000 B Bulk(Bag) 500 HD: for high speed differential signal lines UD: for ultra high speed differential signal lines Part Number Common Mode Impedance (at 100MHz/20°C) Rated Current Rated Voltage Insulation Resistance (min.) Withstand Voltage DC Resistance DLP0NSN670HL2 p 67ohm ±20% 110mA 5Vdc 100M ohm 12.5Vdc 2.4ohm±25% DLP0NSN900HL2 p 90ohm ±20% 100mA 5Vdc 100M ohm 12.5Vdc 3.0ohm±25% DLP0NSN121HL2 p DLP0NSA150HL2 p 120ohm ±20% 90mA 5Vdc 100M ohm 12.5Vdc 3.8ohm±25% DLP0NSC280HL2 p 28ohm ±20% 100mA 5Vdc 100M ohm 12.5Vdc 1.3ohm±25% 15ohm ±5ohm 100mA 5Vdc 100M ohm 12.5Vdc 0.95ohm ±25% Operating Temperature Range: -40°C to +85°C Number of Circuit: 1 0.27±0.1 0.45±0.050.85±0.05 0.65±0.05 (2) (3) (1) (4) 0.5±0.1 0.20+0.05 –0.10 (in mm) : Electrode Impedance (Ω ) Frequency (MHz) 1 10 100 1000 10000 100 1000 10000 Differential Mode Common Mode DLP0NSN121HL2 DLP0NSN900HL2 DLP0NSN670HL2 DLP0NSN121HL2 DLP0NSN900HL2 DLP0NSN670HL2 Impedance (Ω ) Frequency (MHz) 1 10 100 1000 10000 100 1000 10000 Differential Mode Common Mode DLP0NSC280HL2 DLP0NSA150HL2 DLP0NSC280HL2 DLP0NSA150HL2 Frequency (MHz) Insertion Loss (dB) 1 10 100 1000 10000 DLP0NSN900HL2 Frequency (MHz) Insertion Loss (dB) 1 10 100 1000 10000 DLP0NSA150HL2 (1) (4) (2) (3) No polarity.

!Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.

  • This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please review our product specifications or consult the approval sheet for product specifications before ordering.C31E.pdf Mar.28,2011 Chip Ferrite BeadChip EMIFILrChip Common Mode Choke CoilBlock Type EMIFILr Signal Lines Type 161 I Differential Mode Transmission Characteristics (Typ.) DLP0NSC280HL2 DLP Series Signal Lines Type Chip Common Mode Choke Coil DLP0NS Series (03025 Size) DLP0NS Frequency (MHz) Insertion Loss (dB) 1 10 100 1000 10000 DLP0NSC280HL2

!Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.

  • This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please review our product specifications or consult the approval sheet for product specifications before ordering.C31E.pdf Mar.28,2011 Chip Ferrite BeadChip EMIFILrChip Common Mode Choke CoilBlock Type EMIFILr Signal Lines Type 162 6GHz cut-off frequency (for HDMI) is available. DLP11S/DLP11TSeries (0504 Size) DLP Series Signal Lines Type Chip Common Mode Choke Coil I Dimensions I Equivalent Circuit I Packaging I Rated Value (p: packaging code) Continued on the following page. Refer to pages from p.176 to p.179 for mounting information. DLP11S/11T I Impedance-Frequency Characteristics DLP11SA SeriesDLP11SN Series Code Packaging Minimum Quantity L 180mm Reel Embossed Tape 3000 (DLP11S) 5000 (DLP11T) B Bulk(Bag) 500 HD: for high speed differential signal lines UD: for ultra high speed differential signal lines Part Number Common Mode Impedance (at 100MHz/20°C) Rated Current Rated Voltage Insulation Resistance (min.) Withstand Voltage DC Resistance DLP11SN670SL2 p 67ohm ±20% 180mA 5Vdc 100M ohm 12.5Vdc 1.3ohm±25% DLP11SN121SL2 p 120ohm ±20% 140mA 5Vdc 100M ohm 12.5Vdc 2.0ohm±25% DLP11SN161SL2 p 160ohm ±20% 120mA 5Vdc 100M ohm 12.5Vdc 2.7ohm±25% DLP11SN900HL2 p 90ohm ±20% 150mA 5Vdc 100M ohm 12.5Vdc 1.5ohm±25% DLP11SN201HL2 p 200ohm ±20% 110mA 5Vdc 100M ohm 12.5Vdc 3.1ohm±25% DLP11SN241HL2 p 240ohm ±20% 100mA 5Vdc 100M ohm 12.5Vdc 3.5ohm±25% DLP11SN281HL2 p 280ohm ±20% 90mA 5Vdc 100M ohm 12.5Vdc 4.2ohm±25% DLP11SN331HL2 p 330ohm ±20% 80mA 5Vdc 100M ohm 12.5Vdc 4.9ohm±25% DLP11SA350HL2 p 35ohm ±20% 170mA 5Vdc 100M ohm 12.5Vdc 0.9ohm±25% DLP11SA670HL2 p 67ohm ±20% 150mA 5Vdc 100M ohm 12.5Vdc 1.2ohm±25% DLP11SA900HL2 p 90ohm ±20% 150mA 5Vdc 100M ohm 12.5Vdc 1.4ohm±25% Operating Temperature Range: -40°C to +85°C Number of Circuit: 1 1.0±0.1 1.25±0.1 T 0.3±0.1 0.55±0.1 0.25+0.1 –0.05 (1) (2) (3)(4) (in mm) : Electrode Part Number T DLP11S 0.82±0.1 DLP11T 0.3±0.05 (1) (4) (2) (3) No polarity. Impedance (Ω ) Frequency (MHz) 100 1000 1 10 100 1000 10000 DLP11SA900HL2 DLP11SA670HL2 DLP11SA350HL2 DLP11SA900HL2 DLP11SA670HL2 DLP11SA350HL2 Common mode Differential mode Impedance (Ω ) Frequency (MHz) 100 1000 10000 1 10 100 1000 10000 Common mode Differential modeDLP11SN670SL2 DLP11SN281HL2 DLP11SN241HL2 DLP11SN281HL2 DLP11SN331HL2 DLP11SN201HL2 DLP11SN201HL2 DLP11SN241HL2 DLP11SN331HL2 DLP11SN900HL2 DLP11SN121SL2 DLP11SN161SL2 DLP11SN670SL2 DLP11SN900HL2 DLP11SN121SL2 DLP11SN161SL2

!Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.

  • This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please review our product specifications or consult the approval sheet for product specifications before ordering.C31E.pdf Mar.28,2011 Chip Ferrite BeadChip EMIFILrChip Common Mode Choke CoilBlock Type EMIFILr Signal Lines Type 163 I Differential Mode Transmission Characteristics (Typ.) DLP11SA SeriesDLP11SN Series DLP11TB SeriesDLP11TB Series I Impedance-Frequency Characteristics I Differential Mode Transmission Characteristics I Rated Value (p: packaging code) DLP Series Signal Lines Type Chip Common Mode Choke Coil DLP11S/11T Series (0504 Size) DLP11S/11T HD: for high speed differential signal lines UD: for ultra high speed differential signal lines Part Number Common Mode Impedance (at 100MHz/20°C) Rated Current Rated Voltage Insulation Resistance (min.) Withstand Voltage DC Resistance DLP11TB800UL2 p 80ohm ±25% 100mA 5Vdc 100M ohm 12.5Vdc 1.5ohm±25% Operating Temperature Range: -40°C to +85°C Number of Circuit: 1 Differential mode to common mode conversion characteristic (Scd21) at 2.5GHz: -40dB (typ.) Impedance Characteristics between signal lines Z0 (TDR at 50ps): 90ohm±15ohm Frequency (MHz) Insertion Loss (dB) 1 10 100 1000 10000 DLP11SA900HL2 Frequency (MHz) Insertion Loss (dB) 1 10 100 1000 10000 DLP11SN900HL2 Impedance (Ω ) Frequency (MHz) 100 1000 1 10 100 1000 10000 Common Mode Differential Mode DLP11TB800UL2 DLP11TB800UL2 Frequency (MHz) 1 10 100 1000 10000 Insertion Loss (dB) DLP11TB800UL2

!Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.

  • This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please review our product specifications or consult the approval sheet for product specifications before ordering.C31E.pdf Mar.28,2011 Chip Ferrite BeadChip EMIFILrChip Common Mode Choke CoilBlock Type EMIFILr Signal Lines Type 164 1206 size film type chip common mode choke coil. DLP31SSeries (1206 Size) DLP Series Signal Lines Type Chip Common Mode Choke Coil I Dimensions I Equivalent Circuit I Packaging I Impedance-Frequency Characteristics (Main Items) I Rated Value (p: packaging code) Refer to pages from p.176 to p.179 for mounting information. DLP31S Code Packaging Minimum Quantity L 180mm Reel Embossed Tape 3000 B Bulk(Bag) 500 HD: for high speed differential signal lines UD: for ultra high speed differential signal lines Part Number Common Mode Impedance (at 100MHz/20°C) Rated Current Rated Voltage Insulation Resistance (min.) Withstand Voltage DC Resistance DLP31SN121ML2 p 120ohm ±20% 100mA 16Vdc 100M ohm 40Vdc 2.0ohm max. DLP31SN221ML2 p 220ohm ±20% 100mA 16Vdc 100M ohm 40Vdc 2.5ohm max. DLP31SN551ML2 p 550ohm ±20% 100mA 16Vdc 100M ohm 40Vdc 3.6ohm max. Operating Temperature Range: -40°C to +85°C Number of Circuit: 1 3.2±0.15 (2.1)1.6±0.15 0.3±0.2 (1) (3) (2) (4) 0.7±0.2 1.15±0.15 (in mm) : Electrode Impedance (Ω ) Frequency (MHz) 10 100 1000 10000 100 10001 DLP31SN551ML2 DLP31SN221ML2 DLP31SN121ML2 DLP31SN551ML2 DLP31SN221ML2 DLP31SN121ML2 Common mode Differential mode (1) (4) (2) (3) No polarity.

!Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.

  • This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please review our product specifications or consult the approval sheet for product specifications before ordering.C31E.pdf Mar.28,2011 Chip Ferrite BeadChip EMIFILrChip Common Mode Choke CoilBlock Type EMIFILr Signal Lines Type 165 2 circuits in 05025 size, adapt to HDMI line. DLP1NDSeries (0502 Size) DLP Series Signal Lines Type Chip Common Mode Choke Coil I Dimensions I Equivalent Circuit I Packaging I Impedance-Frequency Characteristics I Differential Mode Transmission Characteristics I Rated Value (p: packaging code) Refer to pages from p.176 to p.179 for mounting information. DLP1ND Operating Temperature Range: -40°C to +85°C Number of Circuit: 2 HD: for high speed differential signal lines UD: for ultra high speed differential signal lines Code Packaging Minimum Quantity L 180mm Reel Embossed Tape 5000 B Bulk(Bag) 500 Part Number Common Mode Impedance (at 100MHz/20°C) Rated Current Rated Voltage Insulation Resistance (min.) Withstand Voltage DC Resistance DLP1NDN350HL4 p 35ohm ±20% 100mA 5Vdc 100M ohm 12.5Vdc 1.8ohm±25% DLP1NDN670HL4 p 67ohm ±20% 80mA 5Vdc 100M ohm 12.5Vdc 2.9ohm±25% DLP1NDN900HL4 p 90ohm ±20% 60mA 5Vdc 100M ohm 12.5Vdc 3.7ohm±25% 0.45±0.05 0.2±0.1 0.4±0.1 (1) (2) (3) (4) (5) (6) (7) (8) 1.5±0.1 0.65±0.1 0.2±0.1 (in mm) 0.1 min. : Electrode 1 10 100 1000 10000 100 1000 10000 Frequency (MHz) Impedance (Ω ) Differential mode Common mode DLP1NDN670HL4 DLP1NDN900HL4 DLP1NDN350HL4 DLP1NDN350HL4 DLP1NDN670HL4 DLP1NDN900HL4 -10 Insertion Loss (dB) 10 100 1000 10000 Frequency (MHz) DLP1NDN900HL4 (1) (5) (6) (7) (8) (2) (3) (4) No polarity.

!Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.

  • This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please review our product specifications or consult the approval sheet for product specifications before ordering.C31E.pdf Mar.28,2011 Chip Ferrite BeadChip EMIFILrChip Common Mode Choke CoilBlock Type EMIFILr Signal Lines Type 166 2 circuit built-in, 0804 size, HDMI adapted type available, cut-off frequency 6GHz max. DLP2ADSeries (0804 Size) DLP Series Signal Lines Type Chip Common Mode Choke Coil I Dimensions I Equivalent Circuit I Packaging I Impedance-Frequency Characteristics (Main Items) I Rated Value (p: packaging code) Refer to pages from p.176 to p.179 for mounting information. DLP2AD DLP2ADN SeriesDLP2ADA Series Continued on the following page. Code Packaging Minimum Quantity L 180mm Reel Embossed Tape 3000 B Bulk(Bag) 500 Operating Temperature Range: -40°C to +85°C Number of Circuit: 2 HD: for high speed differential signal lines UD: for ultra high speed differential signal lines Part Number Common Mode Impedance (at 100MHz/20°C) Rated Current Rated Voltage Insulation Resistance (min.) Withstand Voltage DC Resistance DLP2ADA350HL4 p 35ohm ±20% 150mA 5Vdc 100M ohm 12.5Vdc 0.8ohm±25% DLP2ADA670HL4 p 67ohm ±20% 130mA 5Vdc 100M ohm 12.5Vdc 1.0ohm±25% DLP2ADA900HL4 p 90ohm ±20% 120mA 5Vdc 100M ohm 12.5Vdc 1.4ohm±25% DLP2ADN670HL4 p 67ohm ±20% 140mA 5Vdc 100M ohm 12.5Vdc 1.3ohm±25% DLP2ADN900HL4 p 90ohm ±20% 130mA 5Vdc 100M ohm 12.5Vdc 1.7ohm±25% DLP2ADN121HL4 p 120ohm ±20% 120mA 5Vdc 100M ohm 12.5Vdc 2.0ohm±25% DLP2ADN161HL4 p 160ohm ±20% 100mA 5Vdc 100M ohm 12.5Vdc 2.5ohm±25% DLP2ADN201HL4 p 200ohm ±20% 90mA 5Vdc 100M ohm 12.5Vdc 3.2ohm±25% DLP2ADN241HL4 p 240ohm ±20% 80mA 5Vdc 100M ohm 12.5Vdc 3.8ohm±25% DLP2ADN281HL4 p 280ohm ±20% 80mA 5Vdc 100M ohm 12.5Vdc 4.6ohm±25% 0.82±0.1 0.25±0.1 0.5±0.1 (1) (2) (3) (4) (5) (6) (7) (8) 2.0±0.1 1.0±0.1 0.25±0.15 (in mm) : Electrode Frequency (MHz) Impedance (Ω ) 1000 100 1 10 100 1000 10000 DLP2ADA900HL4 Common Mode Differential Mode DLP2ADA900HL4 DLP2ADA670HL4 DLP2ADA350HL4 DLP2ADA670HL4 DLP2ADA350HL4 Impedance (Ω ) Frequency (MHz) 1 10 100 1000 10000 100 1000 10000 DLP2ADN281HL4 DLP2ADN281HL4 Differential mode Common mode DLP2ADN241HL4 DLP2ADN201HL4 DLP2ADN161HL4 DLP2ADN121HL4 DLP2ADN900HL4DLP2ADN670HL4 DLP2ADN241HL4 DLP2ADN201HL4 DLP2ADN161HL4 DLP2ADN121HL4 DLP2ADN900HL4 DLP2ADN670HL4 (1) (5) (6) (7) (8) (2) (3) (4) No polarity.

!Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.

  • This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please review our product specifications or consult the approval sheet for product specifications before ordering.C31E.pdf Mar.28,2011 Chip Ferrite BeadChip EMIFILrChip Common Mode Choke CoilBlock Type EMIFILr Signal Lines Type 167 I Differential Mode Transmission Characteristics (Typ.) DLP2ADN SeriesDLP2ADA Series DLP Series Signal Lines Type Chip Common Mode Choke Coil DLP2AD Series (0504 Size) DLP2AD Frequency (MHz) Insertion Loss (dB) 1 10 100 1000 10000 DLP2ADN900HL4 Frequency (MHz) Insertion Loss (dB) 10 100 1000 10000 DLP2ADA900HL4 DLP2ADA670HL4 DLP2ADA350HL4

!Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.

  • This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please review our product specifications or consult the approval sheet for product specifications before ordering.C31E.pdf Mar.28,2011 Chip Ferrite BeadChip EMIFILrChip Common Mode Choke CoilBlock Type EMIFILr Signal Lines Type 168 2 circuit built-in, 1206 size, meet IEEE1394,USB,LVDS. DLP31DSeries (1206 Size) DLP Series Signal Lines Type Chip Common Mode Choke Coil I Dimensions I Equivalent Circuit I Packaging I Impedance-Frequency Characteristics (Main Items) I Rated Value (p: packaging code) Refer to pages from p.176 to p.179 for mounting information. DLP31D Code Packaging Minimum Quantity L 180mm Reel Embossed Tape 3000 B Bulk(Bag) 500 Operating Temperature Range: -40°C to +85°C Number of Circuit: 2 HD: for high speed differential signal lines UD: for ultra high speed differential signal lines Part Number Common Mode Impedance (at 100MHz/20°C) Rated Current Rated Voltage Insulation Resistance (min.) Withstand Voltage DC Resistance DLP31DN900ML4 p 90ohm ±20% 160mA 10Vdc 100M ohm 25Vdc 1.1ohm max. DLP31DN131ML4 p 130ohm ±20% 120mA 10Vdc 100M ohm 25Vdc 1.1ohm max. DLP31DN201ML4 p 200ohm ±20% 100mA 10Vdc 100M ohm 25Vdc 2.2ohm max. DLP31DN321ML4 p 320ohm ±20% 80mA 10Vdc 100M ohm 25Vdc 3.5ohm max. DLP31DN441ML4 p 440ohm ±20% 70mA 10Vdc 100M ohm 25Vdc 4.3ohm max. 0.4±0.2 1.15±0.15 3.2±0.15 0.3±0.2 1.6±0.15 0.8±0.1 (5) (6) (7) (8) (1) (2) (3) (4) (in mm) : Electrode Impedance (Ω ) Frequency (MHz) 100 1000 10000 1 10 100 1000 Common mode Differential modeDLP31DN201ML4 DLP31DN131ML4 DLP31DN900ML4 DLP31DN441ML4 DLP31DN441ML4 DLP31DN321ML4 DLP31DN201ML4 DLP31DN131ML4 DLP31DN900ML4 DLP31DN321ML4 (1) (5) (6) (7) (8) (2) (3) (4) No polarity.

!Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.

  • This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please review our product specifications or consult the approval sheet for product specifications before ordering.C31E.pdf Mar.28,2011 Chip Ferrite BeadChip EMIFILrChip Common Mode Choke CoilBlock Type EMIFILr Signal Lines Type 169 Wire-wound common choke, HDMI available type prepaird. DLW21SSeries (0805 Size) DLW Series Signal Lines Type Chip Common Mode Choke Coil I Dimensions I Equivalent Circuit I Packaging I Impedance-Frequency Characteristics (Main Items) I Rated Value (p: packaging code) Continued on the following page. DLW21SN_SQ2 Series DLW21SN_HQ2 Series Refer to pages from p.176 to p.179 for mounting information. DLW21S Code Packaging Minimum Quantity L 180mm Reel Embossed Tape 2000 B Bulk(Bag) 500 Operating Temperature Range: -40°C to +85°C Number of Circuit: 1 HD: for high speed differential signal lines UD: for ultra high speed differential signal lines DLW21SR670HQ2 is designed to correct line impedance when ESD protection device is also used. Part Number Common Mode Impedance (at 100MHz/20°C) Rated Current Rated Voltage Insulation Resistance (min.) Withstand Voltage DC Resistance DLW21SN670SQ2 p 67ohm ±25% 400mA 50Vdc 10M ohm 125Vdc 0.25ohm max. DLW21SN900SQ2 p 90ohm ±25% 330mA 50Vdc 10M ohm 125Vdc 0.35ohm max. DLW21SN121SQ2 p 120ohm ±25% 370mA 50Vdc 10M ohm 125Vdc 0.45ohm max. DLW21SN181SQ2 p 180ohm ±25% 330mA 50Vdc 10M ohm 125Vdc 0.35ohm max. DLW21SN261SQ2 p 260ohm ±25% 300mA 50Vdc 10M ohm 125Vdc 0.40ohm max. DLW21SN371SQ2 p 370ohm ±25% 280mA 50Vdc 10M ohm 125Vdc 0.45ohm max. DLW21SN670HQ2 p 67ohm ±25% 320mA 20Vdc 10M ohm 50Vdc 0.31ohm max. DLW21SN900HQ2 p 90ohm ±25% 280mA 20Vdc 10M ohm 50Vdc 0.41ohm max. DLW21SN121HQ2 p 120ohm ±25% 280mA 20Vdc 10M ohm 50Vdc 0.41ohm max. DLW21SR670HQ2 p 67ohm ±25% 400mA 20Vdc 10M ohm 50Vdc 0.25ohm max. 2.0±0.2 (0.4)(0.4) 1.2±0.2 1.2±0.2 (0.45) (0.45) (1) (2) (3)(4) (0.17) (in mm) : Electrode Impedance (Ω ) Frequency (MHz) 10000 1000 100 0.1 1 10 100 1000 DLW21SN371SQ2 DLW21SN261SQ2 DLW21SN181SQ2 DLW21SN121SQ2 DLW21SN900SQ2 DLW21SN670SQ2 Common mode Differential mode DLW21SN371SQ2 DLW21SN261SQ2 DLW21SN181SQ2 DLW21SN121SQ2 DLW21SN900SQ2 DLW21SN670SQ2 Impedance (Ω ) Frequency (MHz) 0.1 100 1000 10 100 1000 Common mode Differential mode DLW21SN670HQ2 DLW21SN900HQ2 DLW21SN121HQ2 DLW21SN670HQ2 DLW21SN900HQ2 DLW21SN121HQ2 (1) (4) (2) (3) No polarity.

!Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.

  • This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please review our product specifications or consult the approval sheet for product specifications before ordering.C31E.pdf Mar.28,2011 Chip Ferrite BeadChip EMIFILrChip Common Mode Choke CoilBlock Type EMIFILr Signal Lines Type 170 I Impedance-Frequency Characteristics (Main Items) I Differential Mode Transmission Characteristics (Typ.) DLW21SR_HQ2 Series DLW21SN_HQ2 Series DLW Series Signal Lines Type Chip Common Mode Choke Coil DLW21S Series (0805 Size) DLW21S Impedance (Ω ) Frequency (MHz) 1 10 100 1000 0.1 100 1000 Common mode Differential mode DLW21SR670HQ2 DLW21SR670HQ2 Frequency (MHz) Insertion Loss (dB) 1 10 100 1000 10000 DLW21SN900HQ2

!Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.

  • This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please review our product specifications or consult the approval sheet for product specifications before ordering.C31E.pdf Mar.28,2011 Chip Ferrite BeadChip EMIFILrChip Common Mode Choke CoilBlock Type EMIFILr Signal Lines Type 171 Low profile wire-wound common choke coil. DLW21HSeries (0805 Size) DLW Series Signal Lines Type Chip Common Mode Choke Coil I Dimensions I Equivalent Circuit I Packaging I Impedance-Frequency Characteristics (Main Items) I Rated Value (p: packaging code) Refer to pages from p.176 to p.179 for mounting information. DLW21H Code Packaging Minimum Quantity L 180mm Reel Embossed Tape 3000 B Bulk(Bag) 500 Operating Temperature Range: -40°C to +85°C Number of Circuit: 1 HD: for high speed differential signal lines UD: for ultra high speed differential signal lines Part Number Common Mode Impedance (at 100MHz/20°C) Rated Current Rated Voltage Insulation Resistance (min.) Withstand Voltage DC Resistance DLW21HN670SQ2 p 67ohm ±25% 330mA 50Vdc 10M ohm 125Vdc 0.35ohm max. DLW21HN900SQ2 p 90ohm ±25% 330mA 50Vdc 10M ohm 125Vdc 0.35ohm max. DLW21HN121SQ2 p 120ohm ±25% 280mA 50Vdc 10M ohm 125Vdc 0.45ohm max. DLW21HN181SQ2 p 180ohm ±25% 250mA 50Vdc 10M ohm 125Vdc 0.50ohm max. 1.2±0.22.0±0.2 0.9±0.1 (0.17) (0.45) (1) (2) (0.45) (4) (3) (0.4)(0.4) (in mm) : Electrode Impedance (Ω ) Frequency (MHz) 0.1 100 1000 10000 1 10 100 1000 Common mode Differential mode DLW21HN670SQ2 DLW21HN121SQ2 DLW21HN900SQ2 DLW21HN670SQ2 DLW21HN121SQ2 DLW21HN900SQ2 DLW21HN181SQ2 DLW21HN181SQ2 (1) (4) (2) (3) No polarity.

!Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.

  • This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please review our product specifications or consult the approval sheet for product specifications before ordering.C31E.pdf Mar.28,2011 Chip Ferrite BeadChip EMIFILrChip Common Mode Choke CoilBlock Type EMIFILr Signal Lines Type 172 1206 size wire-wound common mode choke coil. DLW31SSeries (1206 Size) DLW Series Signal Lines Type Chip Common Mode Choke Coil I Dimensions I Equivalent Circuit I Packaging I Impedance-Frequency Characteristics I Rated Value (p: packaging code) Refer to pages from p.176 to p.179 for mounting information. DLW31S Code Packaging Minimum Quantity L 180mm Reel Embossed Tape 2000 B Bulk(Bag) 500 Operating Temperature Range: -40°C to +85°C Number of Circuit: 1 HD: for high speed differential signal lines UD: for ultra high speed differential signal lines Part Number Common Mode Impedance (at 100MHz/20°C) Rated Current Rated Voltage Insulation Resistance (min.) Withstand Voltage DC Resistance DLW31SN900SQ2 p 90ohm ±25% 370mA 50Vdc 10M ohm 125Vdc 0.3ohm max. DLW31SN161SQ2 p 160ohm ±25% 340mA 50Vdc 10M ohm 125Vdc 0.4ohm max. DLW31SN261SQ2 p 260ohm ±25% 310mA 50Vdc 10M ohm 125Vdc 0.5ohm max. DLW31SN601SQ2 p 600ohm ±25% 260mA 50Vdc 10M ohm 125Vdc 0.8ohm max. DLW31SN102SQ2 p 1000ohm ±25% 230mA 50Vdc 10M ohm 125Vdc 1.0ohm max. DLW31SN222SQ2 p 2200ohm ±25% 200mA 50Vdc 10M ohm 125Vdc 1.2ohm max. 3.2±0.2 (0.6)(0.6) 1.9±0.2 (0.25) 1.6±0.2 (0.6) (0.6) (1) (2) (3)(4) (in mm) : Electrode Impedance (Ω ) Frequency (MHz) 10000 1000 100 0.1 1 10 100 1000 DLW31SN222SQ2 DLW31SN102SQ2 DLW31SN601SQ2 DLW31SN261SQ2 DLW31SN161SQ2 DLW31SN900SQ2 DLW31SN222SQ2 DLW31SN102SQ2 DLW31SN601SQ2 DLW31SN261SQ2 DLW31SN161SQ2 DLW31SN900SQ2 Common mode Differential mode (1) (4) (2) (3) No polarity.

!Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.

  • This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please review our product specifications or consult the approval sheet for product specifications before ordering.C31E.pdf Mar.28,2011 Chip Ferrite BeadChip EMIFILrChip Common Mode Choke CoilBlock Type EMIFILr Power Lines Type 173 Automotive available, up to 10A. PLT10HSeries (12.9x6.6 mm) PLT Series Power Lines Type Large Current Common Mode Choke Coil for Automotive Available I Dimensions I Equivalent Circuit I Packaging I Impedance-Frequency Characteristics I Rated Value (p: packaging code) Refer to pages from p.180 to p.181 for mounting information. PLT10H I Notice (Rating) Code Packaging Minimum Quantity L 180mm Reel Embossed Tape 125 K 330mm Reel Embossed Tape 500 B Bulk(Bag) 50 Part Number Common Mode Impedance (at 10MHz/20°C) Rated Current Rated Voltage Insulation Resistance (min.) Withstand Voltage DC Resistance Common Mode Inductance PLT10HH1026R0PN p 1000ohm 6A 100Vdc 10M ohm 250Vdc 8.0m ohm±0.5m ohm 20µH min. PLT10HH401100PN p 400ohm 10A 100Vdc 10M ohm 250Vdc 3.6m ohm±0.5m ohm 6µH min. PLT10HH501100PN p 500ohm 10A 100Vdc 10M ohm 250Vdc 3.6m ohm±0.5m ohm 9µH min. PLT10HH9016R0PN p 900ohm 6A 100Vdc 10M ohm 250Vdc 8.0m ohm±0.5m ohm 14µH min. Operating Temperature Range (Self-temperature rise is included): -55°C to +105°C (PLT10HH 1026R0/501100 PN), -55°C to +105°C (PLT10HH 401100/9016R0 PN) Number of Circuit: 1 (1) (2) (4) (3) 6.6±0.2 3.2±0.3 1.0±0.2 1.0 ±0.2 12.9±0.2 9.4 max. 2.0±0.32.1±0.3 2.1±0.3 9.1±0.2 13.4 max. (in mm) : Electrode 102 100 1000 10000 1 10 100 1000 Frequency (MHz) Imredance (Ω ) PLT10HH1026R0PN PLT10HH9016R0PN PLT10HH401100PN PLT10HH501100PN (1) (4) (2) (3) No polarity. In operating temperature exceeding +65°C, derating of current is necessary for PLT10H Series. Please apply the derating curve shown in chart according to the operating temperature. Derating 0 2 04 06 0 Operating Temperature [°C] Current [A] 80 100 120 140 PLT10HH102 PLT10HH401 PLT10HH501 PLT10HH901

!Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.

  • This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please review our product specifications or consult the approval sheet for product specifications before ordering.C31E.pdf Mar.28,2011 Chip Ferrite BeadChip EMIFILrChip Common Mode Choke CoilBlock Type EMIFILr !Caution/ Notice 174 Chip Common Mode Choke Coil !Caution/Notice Do not use products beyond the rated current and rated voltage as this may create excessive heat and deteriorate the insulation resistance. 2. Mounting Direction Mount Chip Common Mode Choke Coils in right direction. Wrong direction, which is 90 degrees rotated from right direction, causes not only open or short circuit but also flames or other serious trouble. G Notice (Soldering and Mounting) <Operating Environment> Do not use products in a chemical atmosphere such as chlorine gas, acid or sulfide gas. Do not use products in the environment close to the organic solvent. <Storage and Handling Requirements> 1. Storage Period DLW11G/DLM2HG series should be used within 6 months, the other series should be used within 12 months. Solderability should be checked if this period is exceeded. 2. Storage Conditions (1) Storage temperature: -10 to +40˚C Relative humidity: 15 to 85% Avoid sudden changes in temperature and humidity. (2) Do not store products in a chemical atmosphere such as chlorine gas, acid or sulfide gas. 1. Cleaning Failure and degradation of a product are caused by the cleaning method. When you clean in conditions that are not in mounting information, please contact Murata engineering. 2. Soldering Reliability decreases with improper soldering methods. Please solder by the standard soldering conditions shown in mounting information. 3. Other Noise suppression levels resulting from Murata's EMI suppression filters EMIFILr may vary, depending on the circuits and ICs used, type of noise, mounting pattern, mounting location, and other operating conditions. Be sure to check and confirm in advance the noise suppression effect of each filter, in actual circuits, etc. before applying the filter in a commercial- purpose equipment design. G Handling 1. Resin Coating (Except DLW Series.) Using resin for coating/molding products may affect the products performance. So please pay careful attention in selecting resin. Prior to use, please make the reliability evaluation with the product mounted in your application set. 2. Resin Coating (DLW Series) The impedance value may change due to high cure- stress of resin to be used for coating/molding products. An open circuit issue may occur by mechanical stress caused by the resin, amount/cured shape of resin, or operating condition etc. Some resin contains some impurities or chloride possible to generate chlorine by hydrolysis under some operating condition may cause corrosion of wire of coil, leading to open circuit. So, please pay your careful attention in selecting resin in case of coating/molding the products with the resin. Prior to use the coating resin, please make sure no reliability issue is observed by evaluating products mounted on your board. 3. Caution for Use (DLW Series) When you hold products with a tweezer, please hold by the sides. Sharp materials, such as a pair of tweezers, should not touch the winding portion to prevent breaking the wire. Mechanical shock should not be applied to the products mounted on the board to prevent breaking the core. 4. Brushing When you clean the neighborhood of products such as connector pins, bristles of cleaning brush shall not be touched to the winding portion of this product to prevent the breaking of wire. G Soldering and Mounting 1. Self-heating Please provide special attention when mounting chip common mode choke coils DLW5 series in close proximity to other products that radiate heat. The heat generated by other products may deteriorate the insulation resistance and cause excessive heat in this component. right direction wrong direction Z Z G Storage and Operating Conditions Notice G Rating !Caution 5. Handling of a Substrate After mounting products on a substrate, do not apply any stress to the product caused by bending or twisting to the substrate when cropping the substrate, inserting and removing a connector from the substrate or tightening screw to the substrate. Excessive mechanical stress may cause cracking in the Product. Bending Twisting

!Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.

  • This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please review our product specifications or consult the approval sheet for product specifications before ordering.C31E.pdf Mar.28,2011 Chip Ferrite BeadChip EMIFILrChip Common Mode Choke CoilBlock Type EMIFILr !Caution/ Notice 175 Chip Common Mode Choke Coil !Caution/Notice 1. Do not use products beyond the rated current and rated voltage as this may create excessive heat and deteriorate the insulation resistance. 2. Be sure to provide an appropriate fail-safe function on your product to prevent a second damage that may be caused by the abnormal function or the failure our product. 2. Mounting Direction Mount Chip Common Mode Choke Coils in right direction. Wrong direction, which is 90 degrees rotated from right direction, causes not only open or short circuit but also flames or other serious trouble. G Notice (Soldering and Mounting) G Handling <Operating Environment> Do not use products in a chemical atmosphere such as chlorine gas, acid or sulfide gas. Do not use products in the environment close to the organic solvent. <Storage and Handling Requirements> 1. Storage Period PLT10H series should be used within 12 months. Solderability should be checked if this period is exceeded. 2. Storage Conditions (1) Storage temperature: -10 to +40˚C Relative humidity: 15 to 85% Avoid sudden changes in temperature and humidity. (2) Do not store products in a chemical atmosphere such as chlorine gas, acid or sulfide gas. 1. Cleaning Failure and degradation of a product are caused by the cleaning method. When you clean in conditions that are not in mounting information, please contact Murata engineering. 2. Soldering Reliability decreases with improper soldering methods. Please solder by the standard soldering conditions shown in mounting information. 3. Other Noise suppression levels resulting from Murata's EMI suppression filters EMIFILr may vary, depending on the circuits and ICs used, type of noise, mounting pattern, mounting location, and other operating conditions. Be sure to check and confirm in advance the noise suppression effect of each filter, in actual circuits, etc. before applying the filter in a commercial- purpose equipment design. G Soldering and Mounting 1. Self-heating Please provide special attention when mounting chip common mode choke coils in close proximity to other products that radiate heat. The heat generated by other products may deteriorate the insulation resistance and cause excessive heat in this component. right direction wrong direction Z Z G Storage and Operating Conditions Notice G Rating !Caution 1. Handling of a Substrate After mounting products on a substrate, do not apply any stress to the product caused by bending or twisting to the substrate when cropping the substrate, inserting and removing a connector from the substrate or tightening screw to the substrate. Excessive mechanical stress may cause cracking in the Product. Bending Twisting

!Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.

  • This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please review our product specifications or consult the approval sheet for product specifications before ordering.C31E.pdf Mar.28,2011 Chip Ferrite BeadChip EMIFILrChip Common Mode Choke CoilBlock Type EMIFILr Soldering and Mounting 176 1. Standard Land Pattern Dimensions Soldering and MountingChip Common Mode Choke CoilDLp DLM11G DLM2HG DLP0NS DLP11S DLP11T DLP1ND DLP2AD DLP31S DLP31D DLW21S DLW21H DLW31SN DLW5AH DLW5B oReflow and Flow oReflow Soldering DLP31S DLP31D DLW5AH/5B ∗1: If the pattern is made with wider than 1.2mm (DLW21) / 1.6mm (DLW31S) it may result in components turning around, because melting speed is different. In the worst case, short circuit between lines may occur. 2: If the pattern is made with less than 0.4mm, in the worst case, short circuit between lines may occur due to spread of soldering paste or mount placing accuracy. 3: If the pattern is made with wider than 0.8mm (DLW21) / 1.6mm (DLW31SN), the bending strength will be reduced. Do not use gild pattern; excess soldering heat may dissolve metal of a copper wire. 1.0 0.6 1.0 0.7 0.7 2.1 2.8 0.8 Pitch 0.4 2.2-2.6 0.8 DLM2HG 0.4 1.0 4.0 1.2 2.0 Land Pattern Land Pattern + Solder Resist Solder Resist (in mm) DLW21S/H DLW31SN 0.8 1.6 0.4 0.4 Series a 1.2 1.6 d 2.6 3.7 bc DLP11S DLP11T DLM11G 0.5 1.5 1.1 0.3 DLP2AD 1.75 0.25 0.5 1.5 0.4 DLW21S/21H/31SN a b c d DLP0NS 0.90 0.30 0.50 0.80 0.3 0.9 2.9 5.5 1.3 3.3 4.7 DLP1ND 1.4 0.2 0.4 0.9 0.3 0.55 0.55 1.95 1.55 0.3 0.85 0.3 0.85 0.3 0.55 0.55 o PCB Warping PCB should be designed so that products are not subjected to the mechanical stress caused by warping the board. Poor example Products should be located in the sideways direction (Length: a<b) to the mechanical stress. Good example a b

!Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.

  • This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please review our product specifications or consult the approval sheet for product specifications before ordering.C31E.pdf Mar.28,2011 Chip Ferrite BeadChip EMIFILrChip Common Mode Choke CoilBlock Type EMIFILr Soldering and Mounting 177 2. Solder Paste Printing and Adhesive Application (in mm) When reflow soldering the chip common mode choke coils, the printing must be conducted in accordance with the following cream solder printing conditions. If too much solder is applied, the chip will be prone to damage by mechanical and thermal stress from the PCB and may crack. Standard land dimensions should be used for resist and copper foil patterns. When flow soldering the chip common mode choke coils, apply the adhesive in accordance with the following conditions. If too much adhesive is applied, then it may overflow into the land or termination areas and yield poor solderability. In contrast, if insufficient adhesive is applied, or if the adhesive is not sufficiently hardened, then the chip may become detached during flow soldering process. DLP DLW DLM oGuideline of solder paste thickness: 100-150µm: DLW21S/21H/31S, DLP0NS/11S/11T/1ND/2AD/DLM11G 150-200µm: DLP31D/31S, DLM2HG, DLW5AH/5BS/5BT *Solderability is subject to reflow conditions and thermal conductivity. Please make sure that your product has been evaluated in view of your specifications with our product being mounted to your product. DLP31S/DLM2HG/DLP31D Apply 0.3mg of bonding agent at each chip. Series Solder Paste Printing Adhesive Application DLP31SDLP31D Coating Position of Bonding Agent Coating Position of Bonding Agent DLM2HG Coating Position of Bonding Agent ab a cc d DLW21S/21H/31SDLP0NS/11S/11T/31S/DLM11G a b c d DLW5AH/5BS/5BT 5.5 2.9 0.9 1.3 3.3 4.7 DLP2AD/31D d c a ab DLM2HG 0.4 1.0 4.0 1.2 2.0 DLP0NS DLP11S DLP11T DLP31S DLM11G 0.3 0.7 0.5 1.0 0.5 0.3 0.3 0.3 0.7 0.4 Series a 0.5 0.55 0.55 2.1 0.7 d 0.3 0.55 0.55 0.6 0.5 bc DLW21S/H DLW31S 0.8 1.6 0.5 0.4 Series a 1.2 1.6 d 2.6 3.7 bc DLP1ND DLP2AD DLP31D 0.3 0.55 1.0 0.2 0.25 0.4 Series a 0.4 0.5 0.8 d 0.3 0.4 0.8 bc DL p Chip Common Mode Choke Coil Soldering and Mounting

!Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.

  • This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please review our product specifications or consult the approval sheet for product specifications before ordering.C31E.pdf Mar.28,2011 Chip Ferrite BeadChip EMIFILrChip Common Mode Choke CoilBlock Type EMIFILr Soldering and Mounting 178 3. Standard Soldering Conditions DL p Chip Common Mode Choke Coil Soldering and Mounting (1) Soldering Methods Use flow and reflow soldering methods only. Use standard soldering conditions when soldering chip common mode choke coils. In cases where several different parts are soldered, each having different soldering conditions, use those conditions requiring the least heat and minimum time. Solder: Use Sn-3.0Ag-0.5Cu solder. Use of Sn-Zn based solder will deteriorate performance of products. If using DLP/DLM series with Sn-Zn based solder, please contact Murata in advance. Flux: o Use Rosin-based flux. In case of DLW21/31 series, use Rosin-based flux with converting chlorine content of 0.06 to 0.1wt%. In case of using RA type solder, products should be cleaned completely with no residual flux. o Do not use strong acidic flux (with chlorine content exceeding 0.20wt%) o Do not use water-soluble flux. For additional mounting methods, please contact Murata. oFlow Soldering Profile (Sn-3.0Ag-0.5Cu Solder) DLM2HG DLP31D/31S Series Pre-heating Standard Profile Limit Profile Heating Temp. (T1) Temp. (T2)Time. (t1) 150°C 60s min. 250 °C 4 to 6s 2 times max. 5s max. 2 times max.265±3°C Time. (t2) HeatingCycle of Flow Temp. (T3) Time. (t2) Cycle of Flow Temperature (°C) Pre-heating Time (s) Heating Limit Profile Standard Profile (2) Soldering Profile oReflow Soldering Profile (Sn-3.0Ag-0.5Cu Solder) DLM/DLP DLW21/31 DLW5A/5B Series Standard Profile Limit Profile Temp. (T1) Time. (t1) Heating 220°C min. 30 to 60s 245 ±3°C 2 times max. 230°C min. 260 °C/10s 2 times max.60s max. 220°C min. 30 to 60s 250 ±3°C 2 times max. 230°C min. 260 °C/10s 2 times max.60s max. Cycle of Reflow Peak Temperature (T2) Temp. (T3) Time. (t2) Heating Cycle of Reflow Peak Temperature (T4) 150 180 T3T1 Temperature (°C) 90s±30s time (s) Limit Profile Standard ProfilePre-heating

!Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.

  • This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please review our product specifications or consult the approval sheet for product specifications before ordering.C31E.pdf Mar.28,2011 Chip Ferrite BeadChip EMIFILrChip Common Mode Choke CoilBlock Type EMIFILr Soldering and Mounting 179 DL p Chip Common Mode Choke Coil Soldering and Mounting (3) Reworking with Solder Iron The following conditions must be strictly followed when using a soldering iron. Pre-heating: 150°C 60s min. Soldering iron power output / Tip diameter: 30W max. / ø3mm max. Temperature of soldering iron tip / Soldering time / Times: 350°C max. / 3-4s / 2 times* *1 DLP0NS, DLP11S, DLP11T, DLP1ND, DLP2AD: 380°C max. / 3-4s / 2 times Do not allow the tip of the soldering iron to directly contact the chip. For additional methods of reworking with a soldering iron, please contact Murata engineering. Following conditions should be observed when cleaning chip EMI filter. (1) Cleaning Temperature: 60°C max. (40°C max. for alcohol type cleaner) (2) Ultrasonic Output: 20W/liter max. Duration: 5 minutes max. Frequency: 28 to 40kHz (3) Cleaning agent The following list of cleaning agents have been tested on the individual components. Evaluation of final assembly should be completed prior to production. Do not clean DLW (except DLW21H) series. Before cleaning, please contact Murata engineering. (a) Alcohol cleaning agent Isopropyl alcohol (IPA) (b) Aqueous cleaning agent Pine Alpha ST-100S (4) Ensure that flux residue is completely removed. Component should be thoroughly dried after aqueous agent has been removed with deionized water. 4. Cleaning

!Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.

  • This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please review our product specifications or consult the approval sheet for product specifications before ordering.C31E.pdf Mar.28,2011 Chip Ferrite BeadChip EMIFILrChip Common Mode Choke CoilBlock Type EMIFILr Soldering and Mounting 180 1. Standard Land Pattern Dimensions Soldering and MountingChip Common Mode Choke CoilPL p PLT10H oReflow Soldering (in mm) 2. Solder Paste Printing and Adhesive Application When reflow soldering the chip common mode choke coils, the printing must be conducted in accordance with the following cream solder printing conditions. If too much solder is applied, the chip will be prone to damage by mechanical and thermal stress from the PCB and may crack. Standard land dimensions should be used for resist and copper foil patterns. When flow soldering the chip common mode choke coils, apply the adhesive in accordance with the following conditions. If too much adhesive is applied, then it may overflow into the land or termination areas and yield poor solderability. In contrast, if insufficient adhesive is applied, or if the adhesive is not sufficiently hardened, then the chip may become detached during flow soldering process. PLT10H oGuideline of solder paste thickness: 150-200µm: PLT10H For the solder paste printing pattern, use standard land dimensions. *Solderability is subject to reflow conditions and thermal conductivity. Please make sure that your product has been evaluated in view of your specifications with our product being mounted to your product. Series Solder Paste Printing o PCB Warping PCB should be designed so that products are not subjected to the mechanical stress caused by warping the board. Poor example Products should be located in the sideways direction (Length: a<b) to the mechanical stress. Good example a b Copper Foil Pattern + Resist Copper Foil Pattern Resist PLT10H 4.0 8.0 4.0 2.02.52.0

!Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.

  • This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please review our product specifications or consult the approval sheet for product specifications before ordering.C31E.pdf Mar.28,2011 Chip Ferrite BeadChip EMIFILrChip Common Mode Choke CoilBlock Type EMIFILr Soldering and Mounting 181 PL p Chip Common Mode Choke Coil Soldering and Mounting 3. Standard Soldering Conditions (1) Soldering Methods Use reflow soldering methods only. Use standard soldering conditions when soldering chip common mode choke coils. In cases where several different parts are soldered, each having different soldering conditions, use those conditions requiring the least heat and minimum time. Solder: Use Sn-3.0Ag-0.5Cu solder. Use of Sn-Zn based solder will deteriorate performance of products. Flux: o Use Rosin-based flux. use Rosin-based flux. o Do not use strong acidic flux (with chlorine content exceeding 0.20wt%) o Do not use water-soluble flux. For additional mounting methods, please contact Murata. (2) Soldering Profile oReflow Soldering Profile (Sn-3.0Ag-0.5Cu Solder) PLT10H Series Standard Profile Limit Profile Temp. (T1) Time. (t1) Heating 220°C min. 30 to 60s 250 ±3°C 2 times max. 230°C min. 260 °C/10s 2 times max.60s max. Cycle of Reflow Peak Temperature (T2) Temp. (T3) Time. (t2) Heating Cycle of Reflow Peak Temperature (T4) 150 180 T3T1 Temperature (°C) 90s±30s time (s) Limit Profile Standard ProfilePre-heating (3) Reworking with Solder Iron The following conditions must be strictly followed when using a soldering iron. Pre-heating: 150°C 60s min. Soldering iron power output / Tip diameter: 80W max. / ø3mm max. Temperature of soldering iron tip / Soldering time / Times: 400°C max. / 5s / 2 times Do not allow the tip of the soldering iron to directly contact the chip. For additional methods of reworking with a soldering iron, please contact Murata engineering. Do not clean after soldering. If cleaning, please contact us. 4. Cleaning

!Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.

  • This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please review our product specifications or consult the approval sheet for product specifications before ordering.C31E.pdf Mar.28,2011 Chip Ferrite BeadChip EMIFILrChip Common Mode Choke CoilBlock Type EMIFILr Packaging 182 Chip Common Mode Choke CoilDLp Minimum Quantity and Dimensions of 8mm Width Paper / Embossed Tape Part Number Cavity Size Minimum Qty. (pcs.) DLM11G DLM2HG DLP0NS DLP11S DLP11T DLP1ND DLP2AD DLP31D/31S DLW21S DLW21H DLW31S ø1.5 Direction of Feed a c∗1 4.0±0.1 2.0±0.05 4.0±0.1 3.5±0.05 8.0 1.75±0.1 c c: Depth of Cavity (Embossed Tape) c: Total Thickness of Tape (Paper Tape) Dimension of the cavity of embossed tape is measured at the bottom side. Dimension of the cavity is measured at the bottom side. d <Embossed> b +0.1 ø180mm Reel Paper Tape Embossed Tape Paper Tape Embossed Tapedcba ø330mm Reel Bulk 1.45 2.75 0.95 1.4 1.35 1.7 2.2 3.5 2.25 2.3 3.6 1.2 2.25 0.75 1.2 1.1 0.84 1.2 1.9 1.45 1.55 2.0 0.8 max. 1.3 0.55 0.98 0.45 0.57 0.98 1.3 1.4 1.1 2.1 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.3 0.25 0.3 3000 5000 3000 5000 5000 3000 3000 2000 3000 2000 1000 1000 500 500 500 500 500 500 500 500 500 10000 <Paper> (in mm) (in mm) c: Depth of Cavity a c 8.0±0.1 2.0±0.05 4.0±0.1 5.5±0.05 12.0 0.4 b 1.75±0.1 ø1.5+0.1 Direction of feed DLW5AH DLW5BS DLW5BT Part Number Cavity Size Minimum Qty. (pcs.) 5.4 5.5 5.5 4.1 5.4 5.4 4.4 4.7 2.7 400 400 700 1500 1500 2500 ø180mm Reelcba ø330mm Reel 100 100 100 Bulk Packaging Minimum Quantity and Dimensions of 12mm Width Embossed Tape "Minimum Quantity" means the number of units of each delivery or order. The quantity should be an integral multiple of the "Minimum Quantity".

!Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.

  • This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please review our product specifications or consult the approval sheet for product specifications before ordering.C31E.pdf Mar.28,2011 Chip Ferrite BeadChip EMIFILrChip Common Mode Choke CoilBlock Type EMIFILr Packaging 183 Chip Common Mode Choke CoilPL p Minimum Quantity and Dimensions of 24mm Width Embossed Tape Part Number Cavity Size (mm) Minimum Qty. (pcs.) PLT10H Direction of Feed Dimension of the cavity is measured at the bottom side. ø178mm Reeldcba ø330mm Reel Bulk 13.5 6.5 9.4 0.5 125 50 500 (in mm) Packaging 12.0±0.1 4.0±0.1 2.0±0.1 ø1.5+0.1 24.0±0.2 11.75±0.1 1.75±0.1 b a c d

!Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.

  • This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please review our product specifications or consult the approval sheet for product specifications before ordering.C31E.pdf Mar.28,2011 Chip Ferrite BeadChip EMIFILrChip Common Mode Choke CoilBlock Type EMIFILr Design Kits 184 Part NumberNo. Rated Current (mA) Rated Voltage (Vdc) Common Mode Impedance (at 100MHz, 20 degrees C) Quantity (pcs.) oEKEMDL21L (Chip Common Mode Choke Coils) DLW21HN670SQ2 DLW21HN900SQ2 DLW21HN121SQ2 DLW21HN181SQ2 DLW21SN670SQ2 DLW21SN900SQ2 DLW21SN121SQ2 DLW21SN181SQ2 DLW21SN261SQ2 DLW21SN371SQ2 DLW21SN670HQ2 DLW21SN900HQ2 DLW21SN121HQ2 DLW21SR670HQ2 67Ω± 25% 90Ω± 25% 120Ω± 25% 180Ω± 25% 67Ω± 25% 90Ω± 25% 120Ω± 25% 180Ω± 25% 260Ω± 25% 370Ω± 25% 67Ω± 25% 90Ω± 25% 120Ω± 25% 67Ω± 25% 330 330 280 250 400 330 370 330 300 280 320 280 280 400 DLP0NSA150HL2 DLP0NSC280HL2 DLP0NSN670HL2 DLP0NSN900HL2 DLP0NSN121HL2 15Ω± 5Ω 28Ω± 20% 67Ω± 20% 90Ω± 20% 120Ω± 20% 100 100 110 100 DLP1NDN350HL4 DLP1NDN670HL4 DLP1NDN900HL4 35Ω± 20% 67Ω± 20% 90Ω± 20% 100 DLP2ADN670HL4 DLP2ADN900HL4 DLP2ADN121HL4 DLP2ADN161HL4 DLP2ADN201HL4 DLP2ADN241HL4 DLP2ADN281HL4 67Ω± 20% 90Ω± 20% 120Ω± 20% 160Ω± 20% 200Ω± 20% 240Ω± 20% 280Ω± 20% 140 130 120 100 DLP2ADA350HL4 DLP2ADA670HL4 DLP2ADA900HL4 35Ω± 20% 67Ω± 20% 90Ω± 20% 150 130 120 DLP11SN670SL2 DLP11SN121SL2 DLP11SN161SL2 DLP11SN900HL2 DLP11SN201HL2 DLP11SN241HL2 DLP11SN281HL2 DLP11SN331HL2 DLP11TB800UL2 67Ω± 20% 120Ω± 20% 160Ω± 20% 90Ω± 20% 200Ω± 20% 240Ω± 20% 280Ω± 20% 330Ω± 20% 80Ω± 25% 180 140 120 150 110 100 100 DLP11SA350HL2 DLP11SA670HL2 DLP11SA900HL2 35Ω± 20% 67Ω± 20% 90Ω± 20% 170 150 150 Chip Common Mode Choke CoilDLp Design Kits

!Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.

  • This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please review our product specifications or consult the approval sheet for product specifications before ordering.C31E.pdf Mar.28,2011 Chip Ferrite BeadChip EMIFILrChip Common Mode Choke CoilBlock Type EMIFILr Design Kits 185 Part NumberNo. Rated Current (mA) Rated Voltage (Vdc) Common Mode Impedance (at 100MHz, 20 degrees C) Quantity (pcs.) oEKEMDCC5C (Chip Common Mode Choke Coils for DC Power Line / SMD Block type EMIFILr for Power Line) DLW5AHN402SQ2 DLW5BSN191SQ2 DLW5BSN351SQ2 DLW5BSN102SQ2 DLW5BSN152SQ2 DLW5BSN302SQ2 DLW5BTN101SQ2 DLW5BTN251SQ2 DLW5BTN501SQ2 DLW5BTN102SQ2 DLW5BTN142SQ2 4000Ω (Typ.) 190Ω (Typ.) 350Ω (Typ.) 1000Ω (Typ.) 1500Ω (Typ.) 3000Ω (Typ.) 100Ω (Typ.) 250Ω (Typ.) 500Ω (Typ.) 1000Ω (Typ.) 1400Ω (Typ.) 200 5000 2000 1500 1000 500 6000 5000 4000 2000 1500 Design KitsDL p Chip Common Mode Choke Coil

!Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.

  • This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please review our product specifications or consult the approval sheet for product specifications before ordering.C31E.pdf Mar.28,2011 Chip Ferrite BeadChip EMIFILrChip Common Mode Choke CoilBlock Type EMIFILr Design Kits 186 No. Rated Current (A) Rated Voltage (Vdc) Common Mode Impedance (at 10MHz, 20 degrees C) Quantity (pcs.) oEKEPPL10B (Common Mode Choke Coil) Part Number PLT10HH401100PN PLT10HH501100PN PLT10HH9016R0PN PLT10HH1026R0PN 400Ω (Typ.) 500Ω (Typ.) 900Ω (Typ.) 1000Ω (Typ.) 100 100 100 100 Large Current Common Mode Choke Coils (Automotive Available)PL p Design Kits

Click to View Pricing, Inventory, Delivery & Lifecycle Information: Murata: DLW5AHN402SQ2L DLW5BSN152SQ2L DLW5BSN191SQ2L DLW5BSN102SQ2L DLW5BSN302SQ2L DLW21SN261SQ2L DLW5BSN351SQ2L DLP31SN221SL2B DLP31SN221SL2L DLP31SN121SL2L DLP31DN441ML4L DLP31DN471SL4L DLW21HN670SQ2L DLW21SN670SQ2L DLW21SN181SQ2L DLP11SN161SL2L DLW21HN181SQ2L DLP11SN201SL2L DLW31SN601SQ2L DLP31DN900SL4L DLW21HN121SQ2L DLP31SN551SL2L DLW21SN261SQ2B DLW5BTN102SQ2L DLW5BTN142SQ2L DLW5BTN251SQ2L DLW5BTN501SQ2L DLW5BSN102SQ2B DLP31SN221ML2B DLM2HGN601SZ3L DLP11SN900SL2L DLW31SN900SQ2L DLP31DN900ML4L DLP0NSN900HL2L DLP2ADN121HL4L DLP31SN221ML2L DLW31SN102SQ2L DLP31DN900SL4 DLW31SN222SQ2L DLW31SH222SQ2L DLP31DN201ML4L DLW21SN121SQ2L DLW21SN371SQ2L DLP31DN131ML4L DLP31DN201SL4L DLW21HN900SQ2L DLP11SN121SL2L DLP31DN321ML4L DLW21SN900SQ2L DLW31SN261SQ2L DLW31SN161SQ2L DLP31DN161SL4L DLP31DN361SL4L DLP0NSN121HL2L DLP0NSN670HL2L DLP11SA350HL2L DLP11SA670HL2L DLP11SA900HL2L DLP11SN241HL2L DLP11SN281HL2L DLP11SN331HL2L DLP11SN900HL2L DLP2ADN161HL4L DLP2ADN201HL4L DLP2ADN241HL4L DLP2ADN281HL4L DLP2ADN670HL4L DLP2ADN900HL4L DLW21SN121HQ2L DLW21SN670HQ2L DLW21SR670HQ2L DLW43SH101XK2L DLW43SH510XK2B DLP11TB800UL2L DLW5BTN501SQ2K DLW21SN900HQ2L DLW5BTN101SQ2L DLP31SN121ML2L DLP31SN551ML2L DLP11SN201HL2L DLP11SN670SL2L DLP31DN441ML4B DLM11GN601SZ2D DLM11GN601SD2D DLW43SH101XP2L DLW43SH110XK2L DLW43SH220XK2L