PLE0E561MCO1 NICHICON | Alldatasheet
Document overview
- Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
- PDF pages: 2
Technical content
Ultra Low ESR, High ripple current. Load life of 2000 hours at 105°C. Radial lead type : Lead free flow soldering condition correspondence Adapted to the RoHS directive (2002/95/EC). series Item Performance Characteristics Category Temperature Range Rated Voltage Range Rated Capacitance Range Capacitance Tolerance tan δ ESR ( 1) Leakage Current ( 2) Characteristics of Temperature Impedance Ratio Endurance Damp Heat Resistance to Soldering Heat Marking –55 ~ +105°C 2.5 ~ 6.3V 470 ~ 1500µF ± 20% at 120Hz, 20°C Not more than value of Standard ratings at 120Hz, 20°C Not more than value of Standard ratings at 100kHz, 20°C Not more than value of Standard ratings. After 2 minute's application of rated voltage. 20°C After 2000 hours' application of rated voltage at 105°C, capacitors meet the specified value for life characteristics listed at right. After 1000 hours' application of rated voltage at 60°C 90%RH, capacitors meet the specified value for life characteristics listed at right. To comply with recommended conditions for reflow soldering. Pre-heating shall be done at 150 ~ 200°C and for 60 ~ 180 sec. Peak temp. is 265°C, within 10 sec. Measurement for solder temperature profile shall be made at a point on the terminal nearest where the terminals protrude through the soldering side of PC board. Navy blue print on the case top. CONDUCTIVE POLYMER ALUMINUM SOLID ELECTROLYTIC CAPACITORS Capacitance change tan δ ESR ( 1) Leakage current ( 2) Within ± 20% of initial value ( 3) 150% or less of the initial specified value 150% or less of the initial specified value Initial specified value or less Capacitance change tan δ ESR ( 1) Leakage current ( 2) Within ± 20% of initial value ( 3) 150% or less of the initial specified value 150% or less of the initial specified value Initial specified value or less Capacitance change tan δ ESR ( 1) Leakage current ( 2) Within ± 10% of initial value ( 3) 130% or less of the initial specified value 130% or less of the initial specified value Initial specified value or less ( 1) ESR measurements should be made at a point on the terminal nearest the end seal of the capacitor. ( 2) Conditioning : If there is doubt about the measured result, measurement should be made again after the rated voltage is applied for 120 minutes at the temperature of 105°C. ( 3) Initial value : The value before test of examination of resistance to soldering. Ultra Low ESR LFLE Low ESR
ALUMINUM SOLID ELECTROLYTIC CAPACITORS Rated Voltage (V) Rated Capacitance (µF) Leakage Current (µA) Case Size φD × L (mm ) 2.5 6.3 560 820 820 1000 1500 560 680 820 1200 470 680 820 280 410 410 500 750 448 544 656 960 592 857 1033 6000 6300 6600 7100 7300 6000 6500 7000 7200 6400 6700 6800 0.08 0.08 0.08 0.08 0.08 0.08 0.08 0.08 0.08 0.08 0.08 0.08 8 × 9 8 × 9 8 × 12 10 × 13 10 × 13 8 × 9 8 × 12 10 × 13 10 × 13 8 × 12 10 × 13 10 × 13 L+0.5MAX 15MIN 4MIN φD +0.5 MAX Laminated Case Silvered lead Wire φd LE 680 g 681 Capacitance Series Lot. No. Voltage(g:4V) P ±0.5 P L E G M D O T D Capacitance tolerance (±20% ) Rated Capacitance (680µF) Rated voltage (4V) Series name Configuration Size code Secondary code Type Dimensions Type numbering system (Example : 4V 680µF) Standard ratings ESR (m Ω ) (20˚C / 100kHz) Rated ripple (mArms) (105˚C / 100kHz) φD L P φd 8.0 φ8 × 9L φ8 × 12L 8.5 3.5 0.6 8.0 11.5 3.5 0.6 Size φ10 × 13L 10.0 12.5 5.0 0.6 (mm) tan δ Code Design, Specifications are subject to change without notice. : In this case, 6 will be put at 12th digit of type numbering system. Configuration Printed in Japan T.2006.I.1C φD × L Code 8 × 9 CO 8 × 12 DO 10 × 13 DO V Code 2.5 e g Voltage 6.3 j PLE0E561MCO1 PLE0E821MCO6 PLE0E821MDO1 PLE0E102MDO1 PLE0E152MDO1 PLE0G561MCO1 PLE0G681MDO1 PLE0G821MDO1 PLE0G122MDO1 PLE0J471MDO1 PLE0J681MDO1 PLE0J821MDO1