DATASHEET SEARCH SITE | WWW.ALLDATASHEET.COM

Document overview

  • Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
  • PDF pages: 3

Technical content

Universal AC input/ Full Range Built-in Active PFC function, PF 0.95 Typical High Efficiency (Up to 88%) Output Protections: OVP/SCP/OTP PLC-040S070D PLC-040S105D PLC-040S128D PLC-040S140D\` PLC-040S166D 40Watts Single Output LED Driver PLC-040 D SeriesQualtek Electronics Corporation P P C Page 1 of 3 Output Characteristics Input Characteristics Protection Environmental Characteristics Characteristics Model Rated Current See Note Voltage Range Ripple and Noise (max) Note 1 Voltage Accuracy Line Regulation Load Regulation Rise Time Hold-up Time (Typ.) Voltage Range Frequency Range Power Factor (Typical) Efficiency (Typical) AC Current (max) Inrush Current (max) Leakage Current Over Temperature (OTP) Over Voltage (OVP) Note 2 Short Circuit (SCP) Operating Temperature Operating Relative Humidity Storage Temperature Vibration Waterproof Rating Safety Standards Withstand Voltage Isolation Resistance EMC Emission EMC Immunity Life Time MTBF (MIL-HDBK-217F) Dimension (LxWxH) Note Features: 0.35A (1) 38~114V ±10% Vo ±5% Vo ±1% Vo ±5% Vo 20mS Max @ Rated Load 8.5mS Min (110VAC input, full load), 10mS Min (220VAC input, full load) 1.05A (3) 12~36V 1.28A (3) 10~29V 1.40A (3) 10~25V 1.66A (3) 8~23V 90VAC~305VAC 47Hz-63Hz >0.95 >0.90 88% 0.6A @ 100-277VAC Input Full Load 65A @ 230VAC, 25°C 0.5mA max @ 277VAC >0.95 >0.90 87% >0.95 >0.90 87% >0.95 >0.90 87% >0.95 >0.90 86% 110°C (Temperature of internal components); shut down, auto recover after the temperature decreases 1.2~1.7Vo Long-term mode, auto recovery -35°C~70°C 5% RH to 95% RH -40°C~85°C, 5% to 100% RH non-condensing 10 to 300Hz sweep at constant acceleration of 1.0G(Breadth: 3.5mm) for 1 Hour for each of the perpendicular axes X, Y, Z IP65 UL8750, Compliance to UL1012 UL935, IEC61347 L/N-GND: 4kV, L-N: 2kV I/P-O/P: >100M Ohms / 500VDC / 25°C / 70% RH Compliance to EN55022(CISPR22) Class B, EN61000-3-2 Class A, EN61000-3-3 Compliance to EN61000-3-2, 3 EN61000-4-2, 3, 4, 5, 6, 8, 11, EN61547 More than 78,000Hrs (25°C, 80% Load) More than 492,000Hrs (25°C, 80% Load) 95x70x32mm 1. Ripple & Noise: Measured by 20 MHz bandwidth oscilloscope and the output paralleled with a 0.1 uF ceramic capacitor and a 10 uF electrolytic capacitor. 2. Latch Mode: The power supply shall return to normal operation only after the power is turned on again (1) Non-Class 2 output (USR & CNR) (2) Class 2 output (USR); Non-Class 2 output (CNR) (3) Class 2 output (USR & CNR) Lightning Protection PLC-040S222D 2.22A (3) 6~16V >0.95 >0.90 85% 0.70A (2) 18~54V >0.95 >0.90 87% PLC-040S035D Waterproof (IP65) PLC-040S045D 0.45A (1) 30~89V >0.95 >0.90 88% Constant Current Design

3 Year Warranty

3.33A (3) 4~11V >0.95 >0.90 84% Class 2 Power Unit (See Note) Dimming Control

40Watts Single Output LED Driver PLC-040 D SeriesQualtek Electronics Corporation P P C ISO-9001 Com pany www. qualteku sa.com Page 2 of 3 DIMMING CONTROL V 1-10V INPUT (PURPLE) GND(GREEN) 1-10VdcPLC-040SXXXD 10V OUTPUT (YELLOW) GND(GREEN) 20K PLC-040SXXXD 1-10V INPUT(PURPLE) The dimmer control may be operated from either a potentiometer or from an input signal of 1 – 10 Vdc. Two recommended implementations are provided below. Implementation 1: DC Input Implementation 2: Potentiometer Control Io/Ir Vs Vdim 20% 40% 60% 80% 100% 0 1 2 3 4 5 6 7 8 9 10 11 Vdim(V) Io/Ir Notes: 1. Io is actual output current and Ir is rated current. 2. If the dimming function is not used, please short 10 V output pin (yellow) and 1-10 V input pin(purple). The output current is about 92% Ir when the 1-10V input pin is /f_loating. 3. For the driver to operate properly, the load voltage must be maintained above the minimum voltage threshold (approx. 50% of the max. output voltage for any given model). 4. The dimming voltage can be tuned down to less than 1V, and the output current will be decreased to about 10% Ir; but the connected LEDs may /f_licker. Keeping dimming voltage greater than 1V is strongly recommended. 5. Do not connect the GND of dimming to the output; otherwise, the LED driver will not work normally.

40Watts Single Output LED Driver PLC-040 D SeriesQualtek Electronics Corporation P P C ISO-9001 Com pany www. qualteku sa.com Page 3 of 3 MECHANICAL SPECIFICATIONS UNIT: mm Derating Curve 100 90 120 150 180 210 240 270 300 330 Input Voltage(V) Load(%) 100 -35 -20 -5 10 25 40 55 70 Ambient Temperature(°C) Load(%) Ambient Temperature vs.Load Rev. B