PL602-39OC-R

PL602-35 MICREL | Alldatasheet

Document overview

• Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
• PDF pages: 10

Technical content

750kHz – 800MHz Low Phase Noise Multiplier XO Universal Low Phase Noise IC’s Micrel Inc. • 2180 Fortune Drive • San Jose, CA 95131 • USA • tel +1(408) 944 -0800 • fax +1(408) 474 -1000 • www.micrel.com Rev 03 /07 /201 2 Page 1

FEATURES

 Selectable 750kHz to 800MHz range.  Low phase noise output  -127dBc/Hz for 155.52MHz @ 10kHz offset  -115dBc/Hz for 622.08MHz @ 10kHz offset  LVCMOS (PL602 -37), LVPECL (PL602 -35 and PL602 -38) or LVDS (PL 602 -39) output.  12MHz to 25MHz crystal input.  No ext ernal crystal load capacitors required.  Output Enable selector.  Selectable /16 to x32 frequency divider/ multiplier.  3.3V operation.  Available in 16 -Pin TSSOP or 16-pin 3x3mm QFN GREEN/RoHS compliant packages .

DESCRIPTION

The PL 602 -35 ( LVPECL with in verted OE), PL 602 -37 (LVCMOS ), PL 602 -38 ( LVPECL ), and PL 602 -39 (LVDS) are high perfor mance and low phase noise XO IC chips. They provide phase noise perfor mance as low as –127dBc at 10kHz offset (at 155MHz), by mult i- plying the input crystal frequency up to 32x. The very low jitter makes them ideal for a wide range of applic a- tions, including SONET/SDH and FEC. They accept fundamental parallel resonant mode crystals from 12MHz to 25MHz. BLOCK DIAGRAM PIN CONFIG URATION (Top View) ^: Internal pull -up *: On QFN package, PL 602 -35/ -38 do not have SEL0 available: Pin 10 is VDD, pin 11 is GND. However, PL 602 -37/ -39 have SEL0 (pin 10), and pin11 is VDD. See pin assignment table for d etails. Note: On QFN package there is a large center pad for thermal relief. Thi s pad needs to be connected to GND. OUTPUT ENABLE LOGICAL LEVELS Part # OE State PL602 -38 0 (Default) Output enabled

1 Tri-state

0 Tri-state

1 (Default) Output enabled OE input: Logical states defined by LVPECL levels for PL 602 -38 Logical states defined by LVCMOS levels for PL 602 -37/ -39 PL602-3x VDD XIN XOUT SEL3^ SEL2^ OE GND GND SEL0^ SEL1^ GND CLKC VDD CLKT GND GND TSSOP-16L PL602-3x 1 2 3 4 12 11 10 9 XIN SEL0^ / VDD* SEL1^ VDD / GND* SEL3^ XOUT SEL2^ OE GND GND GND GND VDD CLKT CLKC GND QFN-16L XIN XOUT OE CLKT PL602-3x CLKC PLL by-pass SEL[3:0] PLL (Phase Locked Loop) Oscillator Amplifier integrated load cap.

750kHz – 800MHz Low Phase Noise Multiplier XO Universal Low Phase Noise IC’s Micrel Inc. • 2180 Fortune Drive • San Jose, CA 95131 • USA • tel +1(408) 944 -0800 • fax +1(408) 474 -1000 • www.micrel.com Rev 03 /07 /201 2 Page 2 FREQUENCY SELECTION TABLE SEL3 SEL2 SEL1 SEL0 Selected Multiplier 0 0 1 1 Fin x 32 0 1 1 0 Fin / 8 0 1 1 1 Fin x 2 1 0 0 1 Fin / 2 1 0 1 0 Fin / 16 1 0 1 1 Fin x 4 1 1 0 0 Fin / 4 1 1 0 1 Fin x 8 1 1 1 0 Fin x 16 1 1 1 1 No multiplication Note: SEL0 is not available (always “1”) for PL 602 -35 and PL 602 -38 in 3x3mm package PIN DESCRIPTIONS PL 602-35 and PL 602-38 (see next page for PL602 -37/-39) Name TSSOP Pin nu mber 3x3mm QFN Pin nu mber Type Description XIN 2 12 I Crystal input (See Cry stal Specification on page 4) XOUT 3 13 I Crystal output ( See Crystal Specification on page 4 ) OE 6 16 I Output enable pin ( See OE logic state table on page 1) GND 7,8,9,10,14 1,2,3,4,8,11 P Grou nd connection CLKT 11 5 O LVPECL True output CLKC 13 7 O LVPECL Complementary output SEL0 16 Not avai lable I Multiplier selector pins. These pins have an i nternal pull - up that will default SEL to ‘1’ when not connected to GND. SEL1 15 9 I SEL2 5 15 I SEL3 4 14 I VDD 1, 12 6,10 P +3.3V power supply.

750kHz – 800MHz Low Phase Noise Multiplier XO Universal Low Phase Noise IC’s Micrel Inc. • 2180 Fortune Drive • San Jose, CA 95131 • USA • tel +1(408) 944 -0800 • fax +1(408) 474 -1000 • www.micrel.com Rev 03 /07 /201 2 Page 3 PIN DESCRIPTIONS PL 602-37/-39 (see previous page for PL602-35/-38) Name TSSOP Pin nu mber 3x3mm QFN Pin nu mber Type Description XIN 2 12 I Crystal input. See Crystal Specification on page 4. XOUT 3 13 I Crystal output. See Cry stal Specification on page 4. OE 6 16 I Output enable pin (see OE logic state table on page 1). GND 7,8,9,10,14 1,2,3,4,8 P Ground. CLKT 11 5 O LVDS True output for PL 602 -39. No Connect for PL 602 -37 CLKC 13 7 O LVDS Complementary output for PL602 -39 LVCMOS out for PL 602 -37 SEL0 16 10 I Multiplier selector pins. These pins have an inte rnal pull -up that will default SEL x to ‘1’ when not connected to GND. SEL1 15 9 I SEL2 5 15 I SEL3 4 14 I VDD 1, 12 6,11 P +3.3V po wer supply.

750kHz – 800MHz Low Phase Noise Multiplier XO Universal Low Phase Noise IC’s Micrel Inc. • 2180 Fortune Drive • San Jose, CA 95131 • USA • tel +1(408) 944 -0800 • fax +1(408) 474 -1000 • www.micrel.com Rev 03 /07 /201 2 Page 4 ELECTRICAL SPECIFICA TIONS 1. Absolute Maximum Ratings PARAMETERS SYMBOL MIN. MAX. UNITS Supply Voltage VDD 4.6 V Input Voltage, dc VI -0.5 VDD +0.5 V Output Voltage, dc VO -0.5 VDD +0.5 V Storage Temperature TS -65 150 C Ambient Operati ng Te mperature* TA -40 85 C Junction Temperature TJ 125 C Lead Temperature (so ldering, 10s) 260 C ESD Protection, Human Body Model 2.5 kV Exposure of the device under conditions beyond the limits specified by Maximum Ratings for extended period s may cause permanent damage to the device and affect product reliability. These conditions represent a stress rating only, and functional operations of the device at these or any other conditions above the operational limits noted in this specification is not implied. * Note: Operating Temperature is guaranteed by design for all parts (COMME RCIAL and INDUSTRIAL), but tested for COMMERCIAL grade only. 2. Crystal Specifications PARAM ETERS SYMBOL COND ITIONS MIN. TYP. MAX. UNITS Crystal Resonator Fr equency FXIN Parallel Fu ndamental Mode 12 25 MHz Crystal Loa ding Rating CL (x ta l) 20 pF Reco mmended ESR RE AT cut 30 Ω 3. General Electrical Specifications PARAM ETERS SYMBOL CONDITIONS MIN. TYP. MAX. UNITS Supply Current, Dynamic (with Loaded Ou tputs) IDD LVPECL /LVDS/ LVCMOS FOUT <24MHz 60/28/15 mA 24MHz< FOUT <96MHz 65/45/30 96MHz< FOUT <800MHz 100/80/ 40 Operating Voltage VDD 2.97 3.63 V Output Clock Duty C ycle @ 50% V DD (LVCMOS ) @ 1.25V (LVDS) @ VDD – 1.3V ( LVPECL ) Short Circuit Current 50 mA

750kHz – 800MHz Low Phase Noise Multiplier XO Universal Low Phase Noise IC’s Micrel Inc. • 2180 Fortune Drive • San Jose, CA 95131 • USA • tel +1(408) 944 -0800 • fax +1(408) 474 -1000 • www.micrel.com Rev 03 /07 /201 2 Page 5 4. Jitter Specifications PARAMETERS CONDITIONS FREQUENCY MIN. TYP. MAX. UNITS Period Jitter, RMS With capacitive decoupling between V DD and GND. Over 10,000 cycles. 155.52MHz 4.3 ps 622.08MHz 5.0 Period Jitter, Peak -to-Peak With capacitive decoupling between V DD and GND. Over 10,000 cycles. 155.52MHz 35 ps 622.08MHz 45 Integrated Jitter, RMS Integrated 12 kHz to 20 MHz 155.52MHz 2.4 ps 622.08MHz 2.5 5. Phase Noise Specifications PARAMETERS FREQUENCY @10Hz @100Hz @1kHz @10kHz @100kHz UNITS Phase Noise, relative to carrier (typical) 155.52MHz -63 -93 -117 -126 -123 dBc/Hz 622.08MHz -52 -83 -105 -113 -110 6. LVCMOS Electrical Characteristics PARAM ETERS SYMBOL COND ITIONS MIN. TYP. MAX. UNITS Output drive current IOH VOH = V DD -0.4V, V DD =3.3V 10 mA IOL VOL = 0.4V, V DD = 3.3V 10 mA Output Clock Rise/Fall Time 0.3V ~ 3.0V with 15 pF load 2.4 ns

750kHz – 800MHz Low Phase Noise Multiplier XO Universal Low Phase Noise IC’s Micrel Inc. • 2180 Fortune Drive • San Jose, CA 95131 • USA • tel +1(408) 944 -0800 • fax +1(408) 474 -1000 • www.micrel.com Rev 03 /07 /201 2 Page 6 7. LVDS Electrical Characteristics PARAM ETERS SYMBOL COND ITIONS MIN. TYP. MAX. UNITS Output Differential Vol tage VOD RL = 100Ω (see fi gure) 247 355 454 mV VDD Magnitude Change VOD -50 50 mV Output High Voltage VOH 1.4 1.6 V Output Low Voltage VOL 0.9 1.1 V Offset Vol tage VOS 1.125 1.2 1.375 V Offset Magn itude Change VOS 0 3 25 mV Power -off Leakage IOXD Vou t = V DD or GND VDD = 0V 1 10 uA Output Short Circuit Cu rrent IOSD -5.7 -8 mA 8. LVDS Switching Characteristics PARAM ETERS SYMBOL COND ITIONS MIN. TYP. MAX. UNITS Differential Clock Rise Time tr RL = 100Ω CL = 10 pF (see fi gure) 0.2 0.7 1.0 ns Differential Clock Fall Time tf 0.2 0.7 1.0 ns OUT OUT VOD VOS 50 50 OUT VDIFF RL = 100 CL = 10pF CL = 10pF LVDS Switching Test CircuitLVDS Levels Test Circuit LVDS Transistion Time Waveform OUT OUT OUT 0V (Differential) 20% 80% 20% 80% tR tF VDIFF

750kHz – 800MHz Low Phase Noise Multiplier XO Universal Low Phase Noise IC’s Micrel Inc. • 2180 Fortune Drive • San Jose, CA 95131 • USA • tel +1(408) 944 -0800 • fax +1(408) 474 -1000 • www.micrel.com Rev 03 /07 /201 2 Page 7 9. LVPECL Electrical Characteristics PARAM ETERS SYMBOL COND ITIONS MIN. MAX. UNITS Output High Voltage VOH RL = 50Ω to (V DD – 2V) (see figure) VDD – 1.025 V Output Low Voltage VOL VDD – 1.620 V 10. LVPECL Switching Characteristics PARAM ETERS SYMBOL COND ITIONS MIN. TYP. MAX. UNITS Clock Rise Time tr 20%~80% of Wav eform 0.6 1.5 ns Clock Fall Time tf 0.6 1.5 ns OUT OUT 50? 50? LVPECL Levels Test Circuit LVPECL Transistion Time Waveform OUT OUT 50% 20% 80% tR tF VDD DUTY CYCLE 45 - 55% 55 - 45% 50% OUT OUT tSKEW LVPECL Output Skew 2.0V

750kHz – 800MHz Low Phase Noise Multiplier XO Universal Low Phase Noise IC’s Micrel Inc. • 2180 Fortune Drive • San Jose, CA 95131 • USA • tel +1(408) 944 -0800 • fax +1(408) 474 -1000 • www.micrel.com Rev 03 /07 /201 2 Page 8 PACKAGE INFORM ATION (GREEN PACKAGE COM PLIANT) TSSOP-16L QFN-16L Pin1 Dot DDD DED A b e L SEATING PLANE A1 Min Nom Max A 0.70 0.75 0.80 A1 0.00 - 0.05 b 0.20 0.25 0.30 D 2.95 3.00 3.05 E 2.95 3.00 3.05 D1 1.65 1.70 1.75 E1 1.65 1.70 1.75 L 0.250 0.300 0.350 e 0.50BSC Symbol Dimension (mm) 0.20 Symbol Dimension in MM Min. Max. A - 1.20 A1 0.05 0.15 b 0.19 0.30 C 0.09 0.2 0 D 4.9 0 5.10 E 4.30 4.50 H 6.20 6.60 L 0.45 0.75 e 0.65 BSC C L A E H D e B

750kHz – 800MHz Low Phase Noise Multiplier XO Universal Low Phase Noise IC’s Micrel Inc. • 2180 Fortune Drive • San Jose, CA 95131 • USA • tel +1(408) 944 -0800 • fax +1(408) 474 -1000 • www.micrel.com Rev 03 /07 /201 2 Page 9

ORDERING INFORMATION

For part ordering, please contact our Sales D epartment:

2180 Fortune Drive , San Jose, CA 95131 , USA

Tel: (408) 944 -0800 Fax: (408) 474 -1000 PART NUMB ER The order number for this device is a comb ination of the following: Part number, Package type, Operating temper ature range, shipping method PL602-3x X X - X Part Number Package Type O=TSSOP-16L Q=QFN-16L Temperature C=Commercial (0°C to 70°C) None=Tube R=Tape & Reel Part/Order Number Marking Package Option PL602 -35OC P602 -35 OC LLLLL 16-Pin TSSOP Tube PL602 -35OC-R 16-Pin TSSOP (Tape and Reel) PL602 -35Q C-R P602 LLL 16-Pin 3×3 QFN (Tape and Reel) PL602 -37OC P602 -37 OC LLLLL 16-Pin TSSOP Tube PL602 -37OC-R 16-Pin TSSOP (Tape and Reel) PL602 -37QC -R P602 LLL 16-Pin 3×3 QFN (Ta pe and Reel) PL602 -38OC P602 -38 OC LLLLL 16-Pin TSSOP Tube PL602 -38OC -R 16-Pin TSSOP (Tape and Reel) PL602 -38QC-R P602 LLL 16-Pin 3×3 QFN (Tape and Reel) PL602 -39OC P602 -39 OC LLLLL 16-Pin TSSOP Tube PL602 -39OC -R 16-Pin TSSOP (Tape and Reel) PL602 -39QC-R P602 LLL 16-Pin 3×3 QFN (Tape and Reel) *Note: “LLL ” and “LLLLL ” designates lot number

750kHz – 800MHz Low Phase Noise Multiplier XO Universal Low Phase Noise IC’s Micrel Inc. • 2180 Fortune Drive • San Jose, CA 95131 • USA • tel +1(408) 944 -0800 • fax + 1(408) 474 -1000 • www.micrel.com Rev 03 /07 /201 2 Page Micrel Inc., reserves the right to make changes in its products or specifications, or both at any time without notice. The in formation furnished by Micrel is believed to be accurate and reliable. However, Micrel makes no guara ntee or warranty concerning the accuracy of said information and shall not be responsible for any loss or damage of whatever nature resulting from the use of, or reliance upon this product. LIFE SUPPORT POLICY : Micrel’s products are not authorized for use as critical components in life support devices or systems without the express written approval of the President of Micrel Inc.