PL602-04OC-R

PL602-04 MICREL | Alldatasheet

Document overview

• Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
• PDF pages: 4

Technical content

Low Phase Noise CMO S XO ( 96MHz to 200MHz) Micrel Inc. • 2180 Fortune Drive • San Jose, CA 95131 • USA • tel +1(408) 944 -0800 • fax +1(408) 474 -1000 • www.micrel.com Rev 1 1/1 6/11 Page 1

FEATURES

 Low phase noise XO output for the 96MHz to 200MHz range ( -125 dBc at 10kHz offset).  12 to 25MHz crystal input.  Integrated crystal load capacitor: no e xternal load capacitor required.  Selectable High Drive (30mA) or Sta ndard Drive (10mA) output.  3.3V operation.  Available in 8 -Pin TSSOP or SOIC.

DESCRIPTION

The P L602 -04 is a low cost, high perfor mance and low phase noise XO, providing less than -125 dBc at 10kHz offset in the 96 MHz to 200MHz operating range. The very lo w jitter makes this chip ideal f or applications requiring clean reference fr equency sources. Input crystal can range from 12 to 25MHz (fundamental res onant mode). PIN CONFIGURATION OUTPUT RANGE MULTIPL IER FREQUENCY RANGE OUTPUT BUFFER X8 96 - 200MHz CMOS BLOCK DIAGRAM Reference Divider Phase Comparator Charge Pump Loop Filter VCO VCO Divider XTAL OSC OEXIN XOUT CLK PL602-04 4 5 8CLK VDD OE^ XIN GND N/C XOUT GND Note: ^ de note s inte rna l pull up

Low Phase Noise CMO S XO ( 96MHz to 200MHz) Micrel Inc. • 2180 Fortune Drive • San Jose, CA 95131 • USA • tel +1(408) 944 -0800 • fax +1(408) 474 -1000 • www.micrel.com Rev 1 1/1 6/11 Page 2 PIN DESC RIPTIONS Name Number Type Description CLK 1 O Output clock. VDD 2 P power supply. OE 3 I Output enable input. Disables (tri -state) output when low. Internal pull -up enables output by default if pin is not connected to low. XIN 4 I Crystal input. See C rystal Specification on page 3. XOUT 5 I Crystal output. See Crystal Specification on page 3. N/C 6 - Not connected. GND 7, 8 P Ground. ELECTRICAL SPECIFICA TIONS 1. Absolute Maximum Ratings PARAMETERS SYMBOL MIN. MAX. UNITS Supply Voltage VDD 4.6 V Input Voltage, dc VI -0.5 VDD +0.5 V Output Voltage, dc VO -0.5 VDD +0.5 V Storage Temperature TS -65 150 C Ambient Operating Temperature* TA -40 85 C Lead Temperature (soldering, 10s) 260 C ESD Protection, Human Body Model 2 kV Exposure of th e device under conditions beyond the limits specified by Maximum Ratings for e xtended periods may cause permanent damage to the device and affect product reliability. These conditions represent a stress rating only, and functional operations of the dev ice at these or any other co n- ditions above the operational limits noted in this specification is not implied. * Note : Operating Temperature is guaranteed by design for all parts (COMMERCIAL and INDU STRIAL), but tested for COMMERCIAL grade only. 2. DC Specific ations PARAMETERS SYMBOL CONDITIONS MIN. TYP. MAX. UNITS Supply Current, Dynamic, with Loaded Outputs IDD FXIN = 12 - 25MHz Output load of 10pF 35 mA Operating Vol tage VDD 2.97 3.63 V Output drive cu rrent (High Drive) IOH VOH = V DD -0.4V, V DD =3.3V 30 mA IOL VOL = 0.4V, V DD = 3.3V 30 mA Output drive cu rrent (Standard Drive) IOH VOH = V DD -0.4V, V DD =3.3V 10 mA IOL VOL = 0.4V, V DD = 3.3V 10 mA

Low Phase Noise CMO S XO ( 96MHz to 200MHz) Micrel Inc. • 2180 Fortune Drive • San Jose, CA 95131 • USA • tel +1(408) 944 -0800 • fax +1(408) 474 -1000 • www.micrel.com Rev 1 1/1 6/11 Page 3 3. AC Specifications PARAMETERS SYMBOL CONDITIONS MIN. TYP. MAX. UNITS Input Crystal Frequency 12 25 MHz Output Clock Rise/Fall Time (Standard Drive) 0.3V ~ 3.0V with 15 pF load 2.4 ns Output Clock Rise/Fall Time (High Drive) 0.3V ~ 3.0V with 15 pF load 1.2 Output Clock Duty Cycle Measured @ 50% V DD 45 50 55 % 4. Jitter and Phase Noise S pecif ication PARAMETERS CONDITIONS MIN. TYP. MAX. UNITS RMS Period Jitter (1 sigma – 1000 samples) at 80MHz, with capacitive decoupling between VDD and GND. 20 ps Phase Noise relative to carrier 155.52 MHz @100Hz of fset -100 dBc/Hz Phase Noise relati ve to carrier 155.52 MHz @1kHz offset -115 dBc/Hz Phase Noise relative to carrier 155.52 MHz @10kHz of fset -125 dBc/Hz Phase Noise relative to carrier 155.52 MHz @100kHz of fset -116 dBc/Hz Phase Noise relative to carrier 155.52MHz @1MHz of fset -114 dBc/Hz Phase Noise relative to carrier 155.52MHz @10MHz of fset -132 dBc/Hz 5. Crystal Specifications PARAMETERS SYMBOL MIN. TYP. MAX. UNITS Crystal Resonator Fr equency FXIN 12 25 MHz Crystal Loading Capacitance Ra ting CL (xtal) 20 pF Driving pow er 1 mW ESR RS 30  PACKAGE INFORM ATION C L A

8 PIN ( dimensions in mm )

Symbol Min. Max A 1.34 1.74 A1 0.10 0.25 B 0.33 0.51 C 0.19 0.25 D 4.80 4.95 E 3.80 4.00 H 5.80 6.20 L 0.38 1.27 e 1.27 BSC E H D e B TSSOP Min. Max - 1.20 0.05 0.15 0.19 0.30 0.09 0.20 2.90 3.10 4.30 4.50 6.20 6.60 0.45 0.75

0.65 BSC

Low Phase Noise CMO S XO ( 96MHz to 200MHz) Micrel Inc. • 2180 Fortune Drive • San Jose, CA 95131 • USA • tel +1(408) 944 -0800 • fax +1(408) 474 -1000 • www.micrel.com Rev 1 1/1 6/11 Page 4

ORDERING INFORMATION

Micrel Inc., reserves the right to make changes in its products or specifications, or both at any time without notice. The in formation furnished by Micrel is believed to be accurate and reliable. However, Micrel makes no guarantee or warranty concerning the accuracy of said info rmation and shall not be responsible for any loss or damage of whatever nature resulting from the use of, or reliance upon this product. LIFE SUPPORT POLICY : Micrel’s products are not authorized for use as critical components in life support devices or systems without the express written approval of the President of Micrel Inc. PART NUMBER For part ordering, please contact our Sales Department:

2180 Fortune Driv e, San Jose, CA 95131 , USA

Tel: (408) 944 -0800 Fax: (408) 474 -1000 PART NUMBER The order number for this device is a combination of the following: Device number, Package type and Operating temperature range PL602 -04 (H) X C Part/Order Nu mber (Commercial) Mar king* Package Option PL602-04OC P602 -04 OC LLLLL 8-Pin SOP Tube PL602-04OC -R 8-Pin SOP (Tape and Reel) PL602-04HOC P602 -04 HOC LLLLL 8-Pin SOP Tube PL 602-04HOC -R 8-Pin SOP (Tape and Reel) PL602-04SC P602 -04 SC LLLLL 8-Pin SOP Tube PL 602-04SC-R 8-Pin SOP (Tape and Reel) PL 602-04HSC P602 -04 HSC LLLLL 8-Pin SOP Tube PL 602-04HSC-R 8-Pin SOP (Tape and Reel) *Note: LLL LL designates lot number TEMPER ATURE C=COMMERCIAL I=INDUSTRAL PACKAGE TYPE S=SOIC, O=TSSOP Optional High Drive