PL602-00 MICREL | Alldatasheet
Document overview
- Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
- PDF pages: 4
Technical content
Multiplier XO IC Die for 12 to 25MHz Parallel Resonant Crystals Micrel Inc. • 2180 Fortune Drive • San Jose, CA 95131 • USA • tel +1(408) 944 -0800 • fax +1(408) 474 -1000 • ww w.micrel.com Rev 11/16 /11 Page 1
FEATURES
Integrated crystal osci llator circuitry (XO). Low phase noise ( -125dBc @ 10kHz offset and 155.52MHz output ) Selectable frequency multipliers (x1, x2, x4, x8 as bonding options). 3.3V supply voltage. Uses inexpensive fundamental -mode parallel reson ant crystals (from 12 to 25MHz). Selectable High Drive (30mA) or Standard Drive (10mA) output. Available in DIE (65 mil x 62 mil).
DESCRIPTION
The PL 602 -00 is a monolithic low jitter and low phase noise ( -125dBc @10kHz offset and 155.52MHz output ), high pe rformance CMOS XO IC. This flexible device can be used as a XO with output frequencies ranging from F XIN x 1 to F XIN x 8 thanks to selector pads allowing bonding options (see Divider Selection Table o n this page). This makes the PL 602 -00 ideal for a wide range of applications from 12MHz to 200MHz (including 50MHz, 77.76MHz, 125MHz and 155.52MHz, etc.). BLOCK DIAGRAM DIE SPECIFICATIONS Name Value Size 62 x 65 mil Reverse side GND Pad dimensions 80 micron x 80 micron Thickness 8 mil DIE CONFIGURA TION MULTIPLIER SELECTION SELECTION FXIN CLK (MHz) S2 S1 S0 0 0 0 12MHz – 25MHz FXIN x 2 0 0 1 FXIN x 4 0 1 0 FXIN x 1 1 0 0 FXIN x 8 0 1 1 FXIN x 2* 1 1 0 FXIN x 4* 1 0 1 FXIN x 1* 1 1 1 FXIN x 8* Note: - Selector pads default t o ‘0’, wire bond to VDD to set to ‘1’ - (*) High -drive CMOS output PAD DESCRIPTION Name Number Description XIN 27 Crystal input connection. XOUT 29 Crystal connection. GND 7,10 Ground. CLK 13 Clock Output. S[0:2] 18,19,20 Frequency selection pad VDD 21, 23 3.3V Power Supply. OE 25 Output Enable: ‘0’ to disable (tri - state output), 1’ (default value when not connected) to enabled the output. XIn XO CLKSelectable PLL XOut S[0:2] 181920212325 Y X (0,0) (1550,1475) 62 mil 65 mil GND CLK GND XOUT XIN OE^ VDD VDD S0V S1V S2V Die ID: 4444-44 C502B Note: ^ denotes internal pull up V denotes internal pull down
Multiplier XO IC Die for 12 to 25MHz Parallel Resonant Crystals Micrel Inc. • 2180 Fortune Drive • San Jose, CA 95131 • USA • tel +1(408) 944 -0800 • fax +1(408) 474 -1000 • ww w.micrel.com Rev 11/16 /11 Page 2 ELECTRICAL SPECIFICA TIONS 1. Absolute Maximum Ratings PARAMETERS SYMBOL MIN. MAX. UNITS Supply Voltage VDD 4.6 V Input Voltage, dc VI -0.5 VDD +0.5 V Output Voltage, dc VO -0.5 VDD +0.5 V Storage Temperature TS -65 150 C Ambient Operating Temperature* TA -40 85 C Junction Temperature TJ 125 C Lead Temperature (soldering, 10s) 260 C ESD Protection, Human Body Model 2 kV Exposure of the device under conditions beyond the limits specified by Maximum Ratings for extended periods may cause permane nt damage to the device and affect product reliability. These conditions represent a stress rating only, and functional operations of the device at these or any other co nditions above the operational limits noted in this specification is not implied. * Note : Operating Temperature is guaranteed by design for all parts (COMMERCIAL and INDUSTRIAL), but tested fo r COMMERCIAL grade only. 2. DC Electrical Specifications PARAMETERS SYMBOL CONDITIONS MIN. TYP. MAX. UNITS Supply Curre nt, Dynamic, with Loaded Output IDD FXIN = 12 - 25MHz Output load of 10pF 35 mA Operating Voltage VDD 2.97 3.63 V Output drive cur rent (High Drive) IOH VOH = V DD -0.4V, V DD =3.3V 30 mA IOL VOL = 0.4V, V DD = 3.3V 30 mA Output drive current (Standard Drive) IOH VOH = V DD -0.4V, V DD =3.3V 10 mA IOL VOL = 0.4V, V DD = 3.3V 10 mA 3. AC Electrical Specifications PARAMETERS SYMBOL CONDITIONS MIN. TYP. MAX. UNITS Input Crystal Frequency 12 25 MHz Output Clock Rise/Fall Time (Standard Drive) 0.3V ~ 3.0V with 15 pF load 3.0 ns Output Clock Rise/Fall Time (High Drive) 0.3V ~ 3.0V with 15 pF load 1.2 Output Clock Duty Cycle Measured @ 50% V DD 45 50 55 %
Multiplier XO IC Die for 12 to 25MHz Parallel Resonant Crystals Micrel Inc. • 2180 Fortune Drive • San Jose, CA 95131 • USA • tel +1(408) 944 -0800 • fax +1(408) 474 -1000 • ww w.micrel.com Rev 11/16 /11 Page 3 4. Crystal Specifications PARAMETERS SYMBOL CONDITIONS MIN. TYP. MAX. UNITS Crystal Resonator Frequency FXIN Parallel Fundamental Mode 12 25 MHz Crystal Loading Rating CL ( xtal) 20 pF Recommended ESR RE AT cut 30 5. Jitter and Phase Noise Specification PARAMETERS CONDITIONS MIN. TYP. MAX. UNITS RMS Period Jitter (1 sigma – 1000 samples) at 155MHz, with capacitive decoupling between VDD and GND. 20 ps Phase Noise relative to carrier Carrier Frequency 44 MHz @100Hz offset -113 dBc/Hz @1kHz offset -130 dBc/Hz @10kHz offset -135 dBc/Hz @100kHz offset -128 dBc/Hz @1MHz offset -128 dBc/Hz Phase Noise relative to carrier Carrier Frequency 155.52MHz @100Hz offset -100 dBc/Hz @1kHz offset -115 dBc/Hz @10kHz offset -125 dBc/Hz @100kHz offset -116 dBc/Hz @1MHz offset -114 dBc/Hz @10MHz offset -132 dBc/Hz @40MHz offset -142 dBc/Hz
Multiplier XO IC Die for 12 to 25MHz Parallel Resonant Crystals Micrel Inc. • 2180 Fortune Drive • San Jose, CA 95131 • USA • tel +1(408) 944 -0800 • fax +1(408) 474 -1000 • ww w.micrel.com Rev 11/16 /11 Page 4 PAD ASSIGNMENT Pad # Name X ( m) Y ( m) Description 7 GND 1042 109 Ground. 10 GND 1400 259 Ground. 13 CLK 1400 716 CMOS clock output. 18 S2 1232 1365 Used to select multiplication factor and drive level. Internal pull down. 19 S1 1042 1365 Used to select multiplication factor an d drive level. Internal pull down. 20 S0 854 1365 Used to select multiplication factor and drive level. Internal pull down. 21 VDD 659 1365 3.3V power supply. 23 VDD 459 1365 3.3V power supply. 25 OE 194 1365 Used to enable/disable the output(s). In ternal pull up. 27 XIN 109 1017 Crystal input. See crystal specification page 3. 29 XOUT 109 646 Crystal output. See crystal specification page 3.
ORDERING INFORMATION
Micrel Inc., reserves the right to make changes in its products or specificati ons, or both at any time without notice. The information furnished by Micrel is believed to be accurate and reliable. However, Micrel makes no guarantee or warranty concerning the accuracy of said info rmation and shall not be responsible for any loss or d amage of whatever nature resulting from the use of, or reliance upon this product. LIFE SUPPORT POLICY : Micrel’s products are not authorized for use as critical components in life support devices or systems without the express written approval of the Presi dent of Micrel Inc. For part ordering, please contact our Sales Department:
2180 Fortune Drive , San Jose, CA 95131 , USA
Tel: (408) 944 -0800 Fax: (408) 474 -1000 PART NUMBER The order number for this device is a combination of the following: Device number, Package type and Operating temperature range PL602 -00 D C Order Number Marking Package Option PL602-00DC P602 -00DC Die – Waffle Pack PART NUMBER TEMPERATURE C=COMMERCIAL I=INDUSTRAL PACKAGE TYPE D=DIE