PI3CH480QEX

PI3CH480_V01 DIODES | Alldatasheet

Document overview

• Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
• PDF pages: 11

Technical content

Features

Note: H=High Voltage Level; L=Low Voltage Level

Description

H X Hi-Z Hi-Z Hi-Z Hi-Z Disable L L IA0 IB0 IC0 ID0 S=0 L H IA1 IB1 IC1 ID1 S=1 Notes: 1. No purposely added lead. Fully EU Directive 2002/95/EC (RoHS), 2011/65/EU (RoHS 2) & 2015/863/EU (RoHS 3) compliant . 2. See https://www.diodes.com/quality/lead-free/ for more information about Diodes Incorporated’s definitions of Halogen - and Antimony-free, "Green" and Lead-free. 3. Halogen- and Antimony-free "Green” products are defined as those which contain <900ppm bromine, <900ppm chlorine (<1500 ppm total Br + Cl) and <1000ppm antimony compounds.

PI3CH480 www.diodes.com November 2018 Document Number DS40329 Rev 3-2 2 © Diodes Incorporated PI3CH480 Pin Description Pin No of TSSOP QSOP Pin No of UQFN3x3- Pin Name Description 1 15 S Select Inputs 2, 3, 5, 6, 11,10,14,13 16,1,3,4, 9,8,12,11 IA0, IA1, IB0, IB1, IC0, IC1, ID0, ID1 Data Inputs 4, 7, 9, 12 2,5,7,10 YA, YB, YC, YD Data Outputs 8 6 GND Ground 15 13 1111111 EN Enable 16 14 VCC Power — Center Pad GND — Maximum Ratings 3.3V Supply (Over Operating Range, TA = -40°C ~ +85°C, VCC = 3.3V ± 10%, unless otherwise noted) Symbol Description Test Conditions(1) Min Typ(2) Max Unit VIH Control Input HIGH Voltage Guaranteed Logic HIGH Level 2.0 — — V VIL Control Input LOW Voltage Guaranteed Logic LOW Level -0.5 — 0.8 V VIK Clamp Diode Voltage VCC = Min., IIN = -18mA — -1.3 -1.8 V IIH Input HIGH Current VCC = Max., VIN = VCC — — ±1 μA IIL Input Low Current VCC = Max., VIN = GND — — ±1 μA IOZH High-Impedance Current(3) 0 ≤ Y, In ≤ VCC — — ±1 μA RON Switch On-Resistance(4) VCC = Min., VIN = 0.0V ION = -48mA or -64mA — 4 6 Ω VCC = Min., VIN = 3.6V ION = -15mA — 5 8 Notes: 1. For maximum or minimum conditions, use appropriate value specified under Electrical Characteristics for the applicable device type. 2. Typical values are at VCC = 3.3V, TA = 25°C ambient and maximum loading. 3. Not more than one output should be shorted at one time. Duration of the test should not exceed one second. 4. Measured by the voltage drop between Y and In pin at indicated current through the switch. ON resistance is determined by the lower of the voltages on the two (Y, In) pins. Note: Stresses greater than those listed under MAXIMUM RATINGS may cause permanent damage to the device. This is a stress rating only and functional operation of the device at these or any other condi tions above those indicated in the operational sec tions of this specification is not implied. Exposure to absolute maximum rating conditions for extended periods may affect reliability.

PI3CH480 www.diodes.com November 2018 Document Number DS40329 Rev 3-2 3 © Diodes Incorporated PI3CH480 2.5V Supply (Over Operating Range, TA = -40°C ~ +85°C, VCC = 2.5V ± 10%, unless otherwise noted) Symbol Description Test Conditions(1) Min Typ(2) Max Unit VIH Control Input HIGH Voltage Guaranteed Logic HIGH Level 1.8 — VCC+0.3 V VIL Control Input LOW Voltage Guaranteed Logic LOW Level -0.3 — 0.8 V VIK Clamp Diode Voltage VCC = Max., IIN = -6mA — -0.7 -1.8 V IIH Input HIGH Current VCC = Max., VIN = VCC — — ±1 μA IIL Input Low Current VCC = Max., VIN = GND — — ±1 μA IOZH High-Impedance Current(3) 0 ≤ Y, In ≤ VCC — — ±1 μA RON Switch On-Resistance(4) VCC = Min., VIN = 0.0V ION = -48mA — 4 8 Ω VCC = Min., VIN = 2.25V ION = -15mA — 7 14 Notes: 1. For maximum or minimum conditions, use appropriate value specified under Electrical Characteristics for the applicable device type. 2. Typical values are at VCC = 2.5V, TA = 25°C ambient and maximum loading. 3. Not more than one output should be shorted at one time. Duration of the test should not exceed one second. 4. Measured by the voltage drop between Y and In pin at indicated current through the switch. ON resistance is determined by the lower of the voltages on the two (Y, In) pins. 1.8V Supply (Over Operating Range, TA = -40°C ~ +85°C, VCC = 1.8V ±10%, unless otherwise noted) Symbol Description Test Conditions(1) Min Typ(2) Max Unit VIH Control Input HIGH Voltage Guaranteed Logic HIGH Level 1.2 — VCC+0.3 V VIL Control Input LOW Voltage Guaranteed Logic LOW Level -0.3 — 0.6 V VIK Clamp Diode Voltage VCC = Max., IIN = -18mA — -0.7 -1.8 V IIH Input HIGH Current VCC = Max., VIN = VCC — — ±1 μA IIL Input Low Current VCC = Max., VIN = GND — — ±1 μA IOZH High-Impedance Current(3) 0 ≤ Y, In ≤ VCC — — ±1 μA RON Switch On-Resistance(4) VCC = Min., VIN = 0.0V ION = -48mA — 4 8 Ω VCC = Min., VIN = 1.6V ION = -15mA — 10 25 Notes: 1. For maximum or minimum conditions, use appropriate value specified under Electrical Characteristics for the applicable device type. 2. Typical values are at VCC = 1.8V, TA = 25°C ambient and maximum loading. 3. Not more than one output should be shorted at one time. Duration of the test should not exceed one second. 4. Measured by the voltage drop between Y and In pin at indicated current through the switch. ON resistance is determined by the lower of the voltages on the two (Y, In) pins. Capacitance (TA = 25°C, f = 1MHz) Symbol(1) Description Test Conditions Typ. Max. Unit CIN Input Capacitance VIN = 0V 1.6 2.5 pF COFF(IN) In Capacitance, Switch Off 3.2 4.5 COFF(Y) Y Capacitance, Switch Off 4.9 6.5 CON Y/In Capacitance, Switch On 8.4 10 Note: 1. These parameters are determined by device characterization but are not production tested

PI3CH480 www.diodes.com November 2018 Document Number DS40329 Rev 3-2 4 © Diodes Incorporated PI3CH480 Power Supply Characteristics Symbol Description Test Conditions(1) Min Typ Max Unit ICC Quiescent Power Supply Current VCC = 3.6V, VIN = GND or VCC — 0.2 0.5 mA VCC = 2.5V, VIN = GND or VCC — 0.25 0.6 mA VCC = 1.8V, VIN = GND or VCC — 0.8 1.5 mA Note: 1. For maximum or minimum conditions, use appropriate value specified under Electrical Characteristics for the applicable device. Dynamic Electrical Characteristics (Over Operating Range, TA = -40°C ~ +85°C, VCC = 3.3V ± 10%) Symbol Description Test Conditions Min Typ Max Unit XTALK Crosstalk See Test Diagram — -60 — dB OIRR Off-Isolation See Test Diagram — -60 — BW -3dB Bandwidth See Test Diagram 200 500 — MHz Switch Characteristics Over 3.3V Operating Range Symbol Description Test Conditions(1) Min Typ Max Unit tPLH, tPHL Propagation Delay(2, 3) Y to In, In to Y See Test Diagram — — 0.3 ns tPZH, tPZL Enable Time S or EN to Y or In See Test Diagram 1.5 — 9.0 tPHZ, tPLZ Disable Time S or EN to Y or In See Test Diagram 1.5 — 9.0 Note: 1. See test circuit and waveforms. 2. This parameter is guaranteed but not tested on propagation delays. 3. The switch contributes no propagation delay other than the RC delay of the on-resistance of the switch and the load capacitance. The time constant for the switch alone is of the order of 0.30ns for 10pF load. Because this time constant is much smaller than the rise/fall times of typical driving signals, it adds very little propagation delay to the system. Propagation delay of the switch when used in a system is determined by the driving circuit on the driving side of the switch and its interaction with the load on the driven side. Over 2.5V Operating Range Symbol Description Test Conditions(1) Min Typ Max Unit tPLH, tPHL Propagation Delay(2, 3) Y to In, In to Y See Test Diagram — — 0.3 ns tPZH, tPZL Enable Time S or EN to Y or In See Test Diagram 1.5 — 15.0 tPHZ, tPLZ Disable Time S or EN to Y or In See Test Diagram 1.5 — 12.0 Note: 1. See test circuit and waveforms. 2. This parameter is guaranteed but not tested on propagation delays. 3. The switch contributes no propagation delay other than the RC delay of the on-resistance of the switch and the load capacitance. The time constant for the switch alone is of the order of 0.30ns for 10pF load. Because this time constant is much smaller than the rise/fall times of typical driving signals, it adds very little propagation delay to the system. Propagation delay of the switch when used in a system is determined by the driving circuit on the driving side of the switch and its interaction with the load on the driven side.

PI3CH480 www.diodes.com November 2018 Document Number DS40329 Rev 3-2 5 © Diodes Incorporated PI3CH480 Over 1.8V Operating Range Symbol Description Test Conditions(1) Min Typ Max Unit tPLH, tPHL Propagation Delay(2, 3) Y to In, In to Y See Test Diagram — — 0.3 ns tPZH, tPZL Enable Time S or EN to Y or In See Test Diagram 1.5 — 25.0 tPHZ, tPLZ Disable Time S or EN to Y or In See Test Diagram 1.5 — 12.0 Notes: 1. See test circuit and waveforms. 2. This parameter is guaranteed but not tested on propagation delays. 3. The switch contributes no propagation delay other than the RC delay of the on-resistance of the switch and the load capacitance. The time constant for the switch alone is of the order of 0.30ns for 10pF load. Because this time constant is much smaller than the rise/fall times of typical driving signals, it adds very little propagation delay to the system. Propagation delay of the switch when used in a system is determined by the driving circuit on the driving side of the switch and its interaction with the load on the driven side. Test Circuit for Electrical Characteristics Notes: 1. CL = Load capacitance: includes jig and probe capacitance. 2. RT = Termination resistance: should be equal to ZOUT of the pulse generator. 3. All input impulses are supplied by generators having the following characteristics: PRR ≤ 10 MHz, ZO = 50Ω, tR ≤ 2.5ns, tF ≤ 2.5ns. 4. The outputs are measured one at a time with one transition per measurement.

PI3CH480 www.diodes.com November 2018 Document Number DS40329 Rev 3-2 6 © Diodes Incorporated PI3CH480 Switch Positions Test Switch tPLZ, tPZL 6.0V tPHZ, tPZH GND Prop Delay Open Test Circuit for Dynamic Electrical Characteristics Switching Waveforms Voltage Waveforms Enable and Disable Times Pulse Skew - tSK(p) HP4195A HP11667A VCC R1 T1 50Ω 10pF D.U.T

PI3CH480 www.diodes.com November 2018 Document Number DS40329 Rev 3-2 7 © Diodes Incorporated PI3CH480 Applications Information Logic Inputs Hot Insertion Part Marking L Package Q Package Top mark is not available at this time. To obtain advanced information regarding the top mark, please contact your local sales representative. Rail-to-Rail is a registered trademark of Nippon Motorola, Ltd.

PI3CH480 www.diodes.com November 2018 Document Number DS40329 Rev 3-2 8 © Diodes Incorporated PI3CH480 Mechanical Information 16-TSSOP (L)

PI3CH480 www.diodes.com November 2018 Document Number DS40329 Rev 3-2 9 © Diodes Incorporated PI3CH480 16- QSOP (Q)

PI3CH480 www.diodes.com November 2018 Document Number DS40329 Rev 3-2 10 © Diodes Incorporated PI3CH480 16-UQFN (ZHD)

Ordering Information

Part Numbers Package Code Package Description PI3CH480LEX L 16-Pin, 173mil Wide (TSSOP) PI3CH480QEX Q 16-Pin, 150mil Wide (QSOP) PI3CH480ZHDEX ZHD 16-Pin, 3x3 (UQFN) Notes: 1. No purposely added lead. Fully EU Directive 2002/95/EC (RoHS), 2011/65/EU (RoHS 2) & 2015/863/EU (RoHS 3) compliant. 2. See https://www.diodes.com/quality/lead-free/ for more information about Diodes Incorporated’s definitions of Halogen- and Antimony-free, "Green" and Lead free. 3. Halogen- and Antimony-free "Green” products are defined as those which contain <900ppm bromine, <900ppm chlorine (<1500ppm total Br + Cl) and <1000ppm antimony compounds. 4. E = Pb-free and Green 5. X suffix = Tape/Reel

PI3CH480 www.diodes.com November 2018 Document Number DS40329 Rev 3-2 11 © Diodes Incorporated PI3CH480 IMPORTANT NOTICE DIODES INCORPORATED MAKES NO WARRANTY OF ANY KIND, EXPRESS OR IMPLIED, WITH REGARDS TO THIS DOCUMENT, INCLUDING, BUT NOT LIMI TED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE (AND THEIR EQUIVALENTS UNDER THE LAWS OF ANY JURISDICTION). Diodes Incorporated and its subsidiaries reserve the right to make modifications, enhancements, improvements, corrections or other changes without further notice to this document and any product described herein. Diodes Incorporated does not assume any liability arising out of the application or use of this document or any product described herein; neither does Diodes Incorporated convey any license under its patent or trademark rights, nor the rights of others. Any Customer or user of this document or products described herein in such applications shall assume all risks of such use and will agree to hold Diodes Incorporated and all the companies whose products are represented on Diodes Incorporated website, harmless against all damages. Diodes Incorporated does not warrant or accept any liability whatsoever in respect of any products purchased through unauthor ized sales channel. Should Customers purchase or use Diodes Incorporated products for any unintended or unauthorized application, Customers shall indemnify and hold Diodes Incorporated and its representatives harmless against all claims, damages, expenses, and attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized application. Products described herein may be covered by one or more United States, international or foreign patents pending. Product names and markings noted herein may also be covered by one or more United States, international or foreign trademarks. This document is written in English but may be translated into multiple languages for reference. Only the English version of this document is the final and determinative format released by Diodes Incorporated. LIFE SUPPORT Diodes Incorporated products are specifically not authorized for use as critical components in life support devices or system s without the express written approval of the Chief E xecutive Officer of Diodes Incorporated. As used herein: A. Life support devices or systems are devices or systems which: 1. are intended to implant into the body, or 2. support or sustain life and whose failure to perform when properly used in accorda nce with instructions for use provided in the labeling can be reasonably expected to result in significant injury to the user. B. A critical component is any component in a life support device or system whose failure to perform can be reasonably expe cted to cause the failure of the life support device or to affect its safety or effectiveness. Customers represent that they have all necessary expertise in the safety and regulatory ramifications of their life support d evices or systems, and acknowledge and agree that they are solely responsible for all legal, regulatory and safety -related requirements concerning their products and any use of Diodes Incorporated products in such safety -critical, life support devices or systems, notwithstanding any devices- or systems-related information or support that may be provided by Diodes Incorporated. Further, Customers must fully indemnify Diodes Incorporated and its representatives against any damages arising out of the use of Diodes Incorporated products in such safety-critical, life support devices or systems. Copyright © 2018, Diodes Incorporated www.diodes.com