PI041900 MULTICOMP | Alldatasheet
Document overview
- Manufacturer or author: Provided By alldatasheet.com(free datasheet download site)
- PDF pages: 4
Technical content
Piano Key - Short & Long Actuator DIL Switches Page 1 31/05/05 V1.0 Features:
- SPST with low contact resistance.
- Down for off.
- Vapour phase solderable, IR reflow solderable.
- Insert moulding of terminals and ultrasonic welding.
- Fully sealed construction permits washing with freon, alcohol, water and steam.
- Double contacts for high reliability. 1. Style: This specification describes "WASHABLE OF DUAL IN-LINE PACKAGE SWITCHES", mainly used as signal switch of electric devices, with the general requirements off mechanical and electrical characteristics. Operating temperature : -20°C to +70°C. Storage temperature range : -40°C to +85°C. 2. Current Range: Non-switching : 100mA, 50V dc. Switching : 25mA, 24V dc. 3. Type of Actuation : Actuated by sliding. Dimensions : Millimetres (Inches)
Piano Key - Short & Long Actuator DIL Switches Page 2 31/05/05 V1.0 Item Description Test Conditions Requirements Electric Performance:
1 Visual Examination By visual examination check without any out pressure
and testing. There shall be no defects that affect the serviceability of the product.
2 Contact Resistance
- To be measured between the two terminals associated with each switch pole. 2. Measurements shall be made with a 1KHz shall current contact resistance meter. 50mΩ maximum (initial). 3 Insulation Resistance 500V dc, 1 minute ±5 seconds. 100MΩ minimum.
4 Dielectric Withstanding Voltage
300V ac (50Hz or 60Hz) shall be applied between all the adjacent terminals and between the terminal and the frame for 1 minute. There shall be no breakdown or flashover. 5 Capacitance 1MHz ±10kHz. 5pF maximum. Mechanical Performance:
6 Operation Force
Applied in the direction of operation. ON OFF OFF ON 800gf maximum.
7 Stop Strength
A static load of PI: Short actuator: 1kgf, Long actuator: 1kgf is applied in the operating direction and pulling direction, operated for a period of 15 seconds. There shall be no sign of damage mechanically.
8 Soldering Heat Resistance
- Soldering temperature: As show in item 2 to 6. P.C.Board Terminal PI 260°C ±5°C 5 ±1 seconds. 2. Duration of solder immersion: 5 ±1 seconds. 3. Frequency of solder process: 2 times maximum. (PCB is 1.6mm in thickness).
9 Vibration
Shall be vibrated in accordance with Method 201A of MIL-STD-202F 1.Frequency : 10-55-10Hz 1 minute/cycle 2.Direction : 3 vertical directions including the direction of operation. 3.Test time : 2 hours each direction. As show in item 2 to 6.
10 Shock
Shall be shocked in accordance with Method 213B Condition A MIL-STD-202F 1.Acceleration : 50G. 2.Action time : 11 ±1m seconds. 3.Testing direction : 6 sides. 4.Test cycle : 3 times in each direction. As show in item 2 to 6.
11 Solderability
1.PI soldering temperature : 230 ±5°C. 2.Flux : 5 - 10 seconds. 3.Duration of solder immersion : 3 ±0.5 seconds. No anti-soldering and the coverage of dipping into solder must more than 75% was requested. 4. Test Sequence
Piano Key - Short & Long Actuator DIL Switches Page 3 31/05/05 V1.0 Item Description Test Conditions Requirements Mechanical Performance:
12 Seal (Washable) The switch is placed at a depth of 5cm in fluorocarbon FC-
40 for 1 minute 50°C. 1.Visually monitor the successive bubbling distance within 25mm. 2. As shown in item 2 to 6. Seal Characteristics : (It is not necessary to apply this kind of test for non-washable series). 1. Do not wash immediately after soldering, do it after returning the switches back to thermal temperature. 2. Do not apply external force to the switch during washing. 3. The switch cannot be used where subject to direct contact with water (except for cleaning processing). Durability
13 Operation Life
Measurements shall be made following the test set forth below: 1. 25mA, 24V dc resistive load. 2. Rate of operation : 15 to 20 cycles/minute. 3. Cycle of operation : 200 cycles. 1. As shown in item 3 and 4. 2. Contact resistance : 50mΩ maximum (final-after test). Weather Proof
14 Resistance Low
Following the test set forth below the sample shall be left in normal temperature and humidity conditions for an hour before measurements are made : 1. Temperature : -40 ±3°C 2. Time : 96 hours As show in item 2 to 6.
15 Resistance High
Following the test set forth below the sample shall be left in normal temperature and humidity conditions for an hour before measurements are made : 1. Temperature : 85 ±2°C 2. Time : 96 hours 1. As show in item 3 to 6. 2. Contact resistance : 50mΩ maximum (final-after test).
16 Resistance Humidity
Following the test set forth below the sample shall be left in normal temperature and humidity conditions for an hour before measurements are made : 1. Temperature : 40 ±2°C. 2. Relative Humidity : 90 to 95%. 3. Time : 96 hours. 1. As show in item 4 to 6 2. Contact resistance : 50mΩ maximum (final-after test). 3. Insulation Resistance : 100mΩ minimum. Number of Ways Width (B) Type Part Number 4 12.45 Piano Key - Long Actuator PI041900 8 22.61 PI081900 10 27.69 PI101900 4 12.45 Piano Key - Short Actuator PI040900 8 22.61 PI080900 10 27.69 PI100900 Dimensions : Millimetres Specifications
For enquiries from all other markets Piano Key - Short & Long Actuator DIL Switches Page 4 31/05/05 V1.0 Notes: International Sales Offices: AUSTRALIA– Farnell InOne Tel No: ++ 61 2 9645 8888 Fax No: ++ 61 2 9644 7898 FRANCE – Farnell InOne Tel No: ++ 33 474 68 99 99 Fax No: ++ 33 474 68 99 90 NORWAY– Farnell InOne Tel No: ++ 45 44 53 66 66 Fax No: ++ 45 44 53 66 02 AUSTRIA – Farnell InOne Tel No: ++ 43 662 2180 680 Fax No: ++ 43 662 2180 670 GERMANY – Farnell InOne Tel No: ++ 49 89 61 39 39 39 Fax No: ++ 49 89 613 59 01 PORTUGAL– Farnell InOne Tel No: ++ 34 93 475 8804 Fax No: ++ 34 93 474 5288 ESTONIA – Farnell InOne Tel No: ++ 358 9 560 7780 Fax No: ++ 358 9 345 5411 NETHERLANDS– Farnell InOne Tel No: ++ 31 30 241 7373 Fax No: ++ 31 30 241 7333 UK – Farnell InOne Tel No: ++ 44 8701 200 200 Fax No: ++ 44 8701 200 201 SINGAPORE– Farnell-Newark InOne Tel No: ++ 65 6788 0200 Fax No: ++ 65 6788 0300 HONG KONG– Farnell-Newark InOne Tel No: ++ 852 2268 9888 Fax No: ++ 852 2268 9899 BELGIUM – Farnell InOne Tel No: ++ 32 3 475 2810 Fax No: ++ 32 3 227 3648 BRAZIL – Farnell-Newark InOne Tel No: ++ 55 11 4066 9400 Fax No: ++ 55 11 4066 9410 IRELAND – Farnell InOne Tel No: ++ 353 1 830 9277 Fax No: ++ 353 1 830 9016 SPAIN– Farnell InOne Tel No: ++ 34 93 475 8805 Fax No: ++ 34 93 474 5107 CHINA – Farnell-Newark InOne Tel No: ++86 10 6238 5152 Fax No: ++86 10 6238 5022 ITALY– Farnell InOne Tel No: ++ 39 02 93 995 200 Fax No: ++ 39 02 93 995 300 SWEDEN – Farnell InOne Tel No: ++ 46 8 730 50 00 Fax No: ++ 46 8 83 52 62 MALAYSIA– Farnell-Newark InOne Tel No: ++ 60 3 7873 8000 Fax No: ++ 60 3 7873 7000 SWITZERLAND– Farnell InOne Tel No: ++ 41 1 204 64 64 Fax No: ++ 41 1 204 64 54 DENMARK – Farnell InOne Tel No: ++ 45 44 53 66 44 Fax No: ++ 45 44 53 66 06 UK – CPC ++ 44 8701 202 530 ++ 44 8701 202 531 UK – BuckHickman InOne ++ 44 8450 510 150 ++ 44 8450 510 130 NEW ZEALAND– Farnell InOne Tel No: ++ 64 9 357 0646 Fax No: ++ 64 9 357 0656 EXPORT – Farnell InOne Tel No: ++ 44 8701 200 208 Fax No: ++ 44 8701 200 209 export FINLAND – Farnell InOne Tel No: ++ 358 9 560 7780 Fax No: ++ 358 9 345 5411 Disclaimer This data sheet and its contents (the "Information") belong to the Premier Farnell Group (the "Group") or are licensed to it. No licence is granted for the use of it other than for information purposes in connection with the products to which it relates. No licence of any intellectual property rights is granted. The Information is subject to change without notice and replaces all data sheets previously supplied. The Information supplied is believed to be accurate but the Group assumes no responsibility for its accuracy or completeness, any error in or omission from it or for any use made of it. Users of this data sheet should check for themselves the Information and the suitability of the products for their purpose and not make any assumptions based on information included or omitted. Liability for loss or damage resulting from any reliance on the Information or use of it (including liability resulting from negligence or where the Group w as aware of the possibility of such loss or damage arising) is excluded. This will not operate to limit or restrict the Group's liability for death or personal injury resulting from its negligence. Multicomp is the registered trademark of the Group. © Premier Farnell plc 2004. http://www.farnellinone.com http://www.buckhickmaninone.com http://www.cpc.co.uk