PH9085.XXXNL PULSE | Alldatasheet

Document overview

  • Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
  • PDF pages: 2

Technical content

1 power.pulseelectronics.com P721. G (11/18) http:/ /www.power.pulseelectronics.com/contact Isolation Power Transformers Toroid Platform SMD PH9085.XXXNL and PM2180.XXXNL Electrical Specifications @ 25°C - Operating Temperature -40°C to +125°C Part Number Inductance (1-3) (µH ±35%) Leakage Inductance (1-3) with (4-6) shorted (µH MAX) Capacitance (pF MAX) DCR (1-3) (Ω MAX) DCR (4-6) (Ω MAX) ET MAX (1-3)1 (V-µsec Max) Turns Ratio (1:3) (6:4) Isolated Voltage2 (Vrms)Commerical Automotive6 2500 1. The ET Max is calculated to limit the core loss and temperature rise at 100KHz based on a bipolar flux swing of 210mT Peak. 2. For Push-Pull topology, where the voltage is applied across half the primary winding turns, the ET needs to be derated by 50% for the same flux swing. 3. The applied ET may need to be further derated for higher frequencies based on the temperature rise which results from the core and copper losses A. To calculate total copper loss (W), use the following formula: Copper Loss (W) = Irms_Primary2 * DCR_Primary + Irms_Secondary2*DCR_Secondary B. To calculate total core loss (W), use the following formula: Core Loss (W) = 7.70E-13 * (Frequency in kHz)2.43 * (210 * [ET/ET Max])2.5 Where ET is the applied Volt Second, ET Max is the rated Volt Second for 210mT flux swing C. To calculate temperature rise, use the following formula: Temperature Rise (°C) = 340 * (Core Loss(W) + Copper Loss (W)) 4. The AEC-Q200 temperature and humidity operational life testing was completed using a dielectric strength test of 2750Vdc. 5. Continuous isolation voltage confirmed by 125°C/1000hrs accelerated aging with the bias voltage applied between primary and secondary windings. 6. The PM2180.XXXNL part numbers are AEC-Q200 and IATF16949 certified. The mechanical dimensions are 100% tested in production but do not necessarily meet aproduct capability index (Cpk) >1.33 and therefore may not strictly conform to PPAP . PH9085.XXXNL and PM2185.XXXNL Mechanical Schematic Push Pull Converter Transformer Functional insulation for isolated power supply driver 2.5KVrms isolation (380Vrms continuous) Notes: Dimensions: mm Unless otherwise specified, all tolerances are±0.25

2 power.pulseelectronics.com P721. G (11/18) http:/ /www.power.pulseelectronics.com/contact Isolation Power Transformers Toroid Platform SMD PH9085.XXXNL and PM2180.XXXNL Pulse Worldwide Headquarters

15255 Innovation Drive Ste 100

San Diego, CA 92128 U.S.A. Tel: 858 674 8100 Fax: 858 674 8262 Pulse Europe Pulse Electronics GmbH Am Rottland 12

58540 Meinerzhagen

Tel: 49 2354 777 100 Fax: 49 2354 777 168 Pulse China Headquarters Pulse Electronics (ShenZhen) CO., LTD D708, Shenzhen Academy of Aerospace Technology, The 10th Keji South Road, Nanshan District, Shenzhen, P .R. China 518057 Tel: 86 755 33966678 Fax: 86 755 33966700 Pulse North China Room 2704/2705 Super Ocean Finance Ctr.

2067 Yan An Road West

Tel: 86 21 62787060 Fax: 86 2162786973 Pulse South Asia

3 Fraser Street

0428 DUO Tower

Tel: 65 6287 8998 Fax: 65 6280 0080 Pulse North Asia 1F., No.111 Xiyuan Rd Zhongli City Taoyuan City 32057 Taiwan (R.O.C) Tel: 886 3 4356768 Fax: 886 3 4356820 For More Information Performance warranty of products offered on this data sheet is limited to the parameters specified. Data is subject to change without notice. Other brand and product names mentioned herein may be trademarks or registered trademarks of their respective owners. © Copyright, 2018. Pulse Electronics, Inc. All rights reserved. PH9085.XXXNL is a series of high isolation power supply transformer drivers. Intended to operate in a fixed duty cycle Push Pull topology, it is a part of a low cost solution for delivering lower power (up to 2W) from a low voltage source. A typical implementation would be an isolated RS-485/RS-232 power supply driver circuit, the design is compatible with the MAXIM™ MAX253 IC. A schematic diagram for the Push Pull converter topology is given below. For a fixed 50% duty cycle mode of operation, the output voltage is simply determined by the input voltage and turns ratio. So, with the available turns ratios, a variety of output voltages can be selected. MAXIM is a registered trademark of Maxim Integrated Products. V V PH9085/PM2180 GND CC OUT VIN DRIVER IC TAPE & REEL INFO SURFACE MOUNTING TYPE, REEL/TAPE LIST PART NUMBER REEL SIZE (mm) TAPE SIZE (mm) QTY A G P1 W K0 PCS/REEL PH9085.XXXNLT/PM2180.XXXNLT Ø330 16.4 12 16 6.6 700 APPLICATION P W K0 1 A G Direction of tape Mark ing Mark ing