PGA4311_07 BURR-BROWN | Alldatasheet
Document overview
- Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
- PDF pages: 15
Technical content
SBOS230A – MARCH 2002 – REVISED JUNE 2002 /C0052/C0262/C0067/C0104/C0097/C0110/C0110/C0101/C0108 /C0065/C0117/C0100/C0105/C0111 /C0086/C0111/C0108/C0117/C0109/C0101 /C0067/C0111/C0110/C0116/C0114/C0111/C0108 /C0080/C0071/C0065/C0052/C0051/C0049/C0049
FEATURES
/C0068DIGITALLY-CONTROLLED ANALOG VOLUME CONTROL: Four Independent Audio Channels Serial Control Interface Zero Crossing Detection Mute Function /C0068WIDE GAIN AND ATTENUATION RANGE: +31.5dB to –95.5dB with 0.5dB Steps /C0068LOW NOISE AND DISTORTION: 120dB Dynamic Range 0.0004% THD+N at 1kHz (U–Grade) 0.0002% THD+N at 1kHz (A–Grade) /C0068NOISE-FREE LEVEL TRANSITIONS /C0068LOW INTERCHANNEL CROSSTALK: –130dBFS /C0068POWER SUPPLIES: ±5V Analog, +5V Digital /C0068AVAILABLE IN AN SOP-28 PACKAGE
APPLICATIONS
/C0068AUDIO AMPLIFIERS /C0068MIXING CONSOLES /C0068MULTI–TRACK RECORDERS /C0068BROADCAST STUDIO EQUIPMENT /C0068MUSICAL INSTRUMENTS /C0068EFFECTS PROCESSORS /C0068A/V RECEIVERS /C0068CAR AUDIO SYSTEMS
DESCRIPTION
The PGA4311 is a high–performance, 4-channel audio volume control designed for professional and high-end consumer audio systems. Using high performance operational amplifier stages internal to the PGA4311 yields low noise and distortion, while providing the capability to drive 600Ω loads directly without buffering. The 3-wire serial control interface allows for connection to a wide variety of host controllers, in addition to support for daisy-chaining of multiple PGA4311 devices. www.ti.com Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet. Copyright 2002, Texas Instruments Incorporated/C0080/C0082/C0079/C0068/C0085/C0067/C0084/C0073/C0079/C0078 /C0068/C0065/C0084/C0065 /C0105/C0110/C0102/C0111/C0114/C0109/C0097/C0116/C0105/C0111/C0110 /C0105/C0115 /C0099/C0117/C0114/C0114/C0101/C0110/C0116 /C0097/C0115 /C0111/C0102 /C0112/C0117/C0098/C0108/C0105/C0099/C0097/C0116/C0105/C0111/C0110 /C0100/C0097/C0116/C0101/C0046 /C0080/C0114/C0111/C0100/C0117/C0099/C0116/C0115 /C0099/C0111/C0110/C0102/C0111/C0114/C0109 /C0116/C0111 /C0115/C0112/C0101/C0099/C0105/C0102/C0105/C0099/C0097/C0116/C0105/C0111/C0110/C0115 /C0112/C0101/C0114 /C0116/C0104/C0101 /C0116/C0101/C0114/C0109/C0115 /C0111/C0102 /C0084/C0101/C0120/C0097/C0115 /C0073/C0110/C0115/C0116/C0114/C0117/C0109/C0101/C0110/C0116/C0115 /C0115/C0116/C0097/C0110/C0100/C0097/C0114/C0100 /C0119/C0097/C0114/C0114/C0097/C0110/C0116/C0121/C0046 /C0080/C0114/C0111/C0100/C0117/C0099/C0116/C0105/C0111/C0110 /C0112/C0114/C0111/C0099/C0101/C0115/C0115/C0105/C0110/C0103 /C0100/C0111/C0101/C0115 /C0110/C0111/C0116 /C0110/C0101/C0099/C0101/C0115/C0115/C0097/C0114/C0105/C0108/C0121 /C0105/C0110/C0099/C0108/C0117/C0100/C0101 /C0116/C0101/C0115/C0116/C0105/C0110/C0103 /C0111/C0102 /C0097/C0108/C0108 /C0112/C0097/C0114/C0097/C0109/C0101/C0116/C0101/C0114/C0115/C0046 Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet.
/C0080/C0071/C0065/C0052/C0051/C0049/C0049 SBOS230A – MARCH 2002 – REVISED JUNE 2002 www.ti.com ABSOLUTE MAXIMUM RATINGS (1) (1)Stresses above these ratings may cause permanent damage. Exposure to absolute maximum conditions for extended periods may degrade device reliability. ELECTROSTATIC DISCHARGE SENSITIVITY This integrated circuit can be damaged by ESD. Texas Instruments recommends that all integrated circuits be handled with appropriate precautions. Failure to ob- serve proper handling and installation procedures can cause damage. ESD damage can range from subtle performance degradation to complete device failure. Precision integrated circuits may be more susceptible to damage because very small parametric changes could cause the device not to meet its published specifications. PACKAGE/ORDERING INFORMATION PRODUCT PACKAGE –LEAD PACKAGE DESIGNATOR (1) OPERATING TEMPERATURE RANGE PACKAGE MARKING ORDERING NUMBER TRANSPORT MEDIA, QUANTITY PGA4311 (U Grade) SOP 28 DW 40°Ct o+ 8 5°C PGA4311U PGA4311U Rails PGA4311 (U–Grade) SOP –28 DW –40°C to +85°C PGA4311U PGA4311U/1K Tape and Reel, 1000 PGA4311 (A Grade) SOP 28 DW 40°Ct o+ 8 5°C PGA4311UA PGA4311UA Rails PGA4311 (A–Grade) SOP –28 DW –40°C to +85°C PGA4311UA PGA4311UA/1K Tape and Reel, 1000 (1)For the most current specifications and package information, refer to our web site at www. ti.com.
ELECTRICAL CHARACTERISTICS
At TA = +25°C, VA+ = +5V, VA– = –5V, VD + = +5V, RL = 100kΩ , CL = 20pF, BW measure = 10Hz to 20kHz, unless otherwise noted. PARAMETER CONDITIONS PGA4311U (U –Grade) PGA4311UA (A –Grade) UNITSPARAMETER CONDITIONS MIN TYP MAX MIN TYP MAX UNITS DC CHARACTERISTICS Step Size 0.5 0.5 dB Gain Error Gain Setting = 31.5dB ±0.05 ±0.05 dB Gain Matching ±0.05 ±0.05 dB Input Resistance 10 10 kΩ Input Capacitance 3 3 pF AC CHARACTERISTICS THD+N VIN = 2Vrms, f = 1kHz 0.0004 0.001 0.0002 0.0004 % Dynamic Range VIN = AGND, Gain = 0dB 116 120 116 120 dB Voltage Range, Output (VA–) + 1.25 (VA+) – 1.25 (VA–) + 1.25 (VA+) – 1.25 V Voltage Range, Input (without clipping) 2.5 2.5 Vrms Output Noise VIN = AGND, Gain = 0dB 2.5 4 2.5 4 µVrms Interchannel Crosstalk f = 1kHz –130 –130 dBFS OUTPUT BUFFER Offset Voltage VIN = AGND, Gain = 0dB 0.25 0.5 0.25 0.5 mV Load Capacitance Stability 100 100 pF Short–Circuit Current 50 50 mA Unity–Gain Bandwidth, Small Signal 10 10 MHz
/C0080/C0071/C0065/C0052/C0051/C0049/C0049 SBOS230A – MARCH 2002 – REVISED JUNE 2002 www.ti.com ELECTRICAL CHARACTERISTICS (Cont.) At TA = +25°C, VA+ = +5V, VA– = –5V, VD + = +5V, RL = 100kΩ , CL = 20pF, BW measure = 10Hz to 20kHz, unless otherwise noted. PARAMETER CONDITIONS PGA4311U (U –Grade) PGA4311UA (A –Grade) UNITSPARAMETER CONDITIONS MIN TYP MAX MIN TYP MAX UNITS DIGITAL CHARACTERISTICS High–Level Input Voltage, VIH +2.0 VD + +2.0 VD + V Low –Level Input Voltage, VIL –0.3 0.8 –0.3 0.8 V High–Level Output Voltage, VOH IO = 200µA (VA+) – 1.0 (VD +) – 1.0 V Low –Level Output Voltage, VOL IO = –3.2mA 0.4 0.4 V Input Leakage Current 1 10 1 10 µA SWITCHING CHARACTERISTICS Serial Clock (SCLK) Frequency fSCLK 0 6.25 0 6.25 MHz Serial Clock (SCLK) Pulse Width LOW tPH 80 80 ns Serial Clock (SCLK) Pulse Width HIGH tPL 80 80 ns MUTE Pulse Width LOW tMI 2.0 2.0 ms Input Timing SDI Setup Time tSDS 20 20 ns SDI Hold Time tSDH 20 20 ns CS Falling to SCLK Rising tCSCR 90 90 ns SCLK Falling to CS Rising tCFCS 35 35 ns Output Timing CS LOW to SDO Active tCSO 35 35 ns SCLK Falling to SDO Data Valid tCFDO 60 60 ns CS HIGH to SDO High Impedance tCSZ 100 100 ns POWER SUPPLY Operating Voltage Quiescent Current IA+ VA+ = +5V 17 22 17 22 mA IA– VA– = –5V 19 24 19 24 mA ID + VD + = +5V 0.5 1.0 0.5 1.0 mA Power–Supply Rejection Ratio PSRR (250Hz) 100 100 dB TEMPERATURE RANGE Operating Range –40 +85 –40 +85 °C Storage Range –65 +150 –65 +150 °C
/C0080/C0071/C0065/C0052/C0051/C0049/C0049 SBOS230A – MARCH 2002 – REVISED JUNE 2002 www.ti.com PIN CONFIGURATION Top View SO PIN ASSIGNMENTS PIN NAME FUNCTION
1 MUTE Mute Control Input (Active LOW)
2 AGND_1 Analog Ground, Channel 1
3 AIN_1 Analog Input, Channel 1
4 AGND_1 Analog Ground, Channel 1
5 AOUT _1 Analog Output, Channel 1
6 VA– Analog Power Supply, –5V
7 VA+ Analog Power Supply, +5V
8 AOUT _3 Analog Output, Channel 3
9 AGND_3 Analog Ground, Channel 3
10 AIN_3 Analog Input, Channel 3
11 AGND_3 Analog Ground, Channel 3
12 VD + Digital Power Supply, +5V
13 SDI Serial Data Input
14 CS Chip Select Input
15 SCLK Serial Clock Input
16 SDO Serial Data Output
17 DGND Digital Ground
18 AGND_4 Analog Ground, Channel 4
19 AIN_4 Analog Input, Channel 4
20 AGND_4 Analog Ground, Channel 4
21 AOUT _4 Analog Output, Channel 4
22 VA+ Analog Power Supply, +5V
23 VA– Analog Power Supply, –5V
24 AOUT _2 Analog Output, Channel 2
25 AGND_2 Analog Ground, Channel 2
26 AIN_2 Analog Input, Channel 2
27 AGND_2 Analog Ground, Channel 2
28 ZCEN Zero Crossing Enable (Active HIGH)
/C0080/C0071/C0065/C0052/C0051/C0049/C0049 SBOS230A – MARCH 2002 – REVISED JUNE 2002 www.ti.com TYPICAL CHARACTERISTICS At TA = +25°C, VA+ = +5V, VA– = –5V, VD + = +5V, RL = 100kΩ , CL = 20pF, BW measure = 10Hz to 20kHz, unless otherwise noted. (NOTE: All plots taken with PGA4311 A–Grade.)
/C0080/C0071/C0065/C0052/C0051/C0049/C0049 SBOS230A – MARCH 2002 – REVISED JUNE 2002 www.ti.com TYPICAL CHARACTERISTICS (Cont.) At TA = +25°C, VA+ = +5V, VA– = –5V, VD + = +5V, RL = 100kΩ , CL = 20pF, BW measure = 10Hz to 20kHz, unless otherwise noted. (NOTE: All plots taken with PGA4311 A–Grade.) GENERAL DESCRIPTION The PGA4311 is a four-channel audio volume control. It may be used in a wide array of professional and consumer audio equipment. The PGA4311 is fabricated in a sub-micron CMOS process. The heart of the PGA4311 is a resistor network, an analog switch array, and a high-performance op amp stage. The switches are used to select taps in the resistor network that, in turn, determine the gain of the amplifier stage. Switch selections are programmed using a serial control port. The serial port allows connection to a wide variety of host controllers. See Figure 1 for a functional block diagram of the PGA4311. POWER –UP STATE On power up, “power-up reset” is activated for about 100ms during which the circuit is in hardware MUTE state and all internal flip-flops are reset. At the end of this period, the offset calibration is initiated without any external signals. Once this has been completed, the gain byte value for all channels are set to 00 HEX , or the software MUTE condi- tion. The gain will remain at this setting until the host con- troller programs new settings for for each channel via the serial control port.
Figure 1. PGA4311 Block Diagram. power-supply voltage returns to greater than ±3.2V. The PGA4311 includes four independent channels. Each channel has a corresponding input and output pin. Typical Characteristics section of the datasheet.
Figure 3. Serial Interface Timing Requirements.
terface to control many PGA4311 devices. to allow enough SCLK cycles to load all devices. tion that can provide for noise-free level transitions. ing of the input signal, thus minimizing audible glitches. Figure 4. Daisy-Chaining Multiple PGA4311 Devices.
Figure 6. Typical PCB Layout Floor Plan.
/C0080/C0071/C0065/C0052/C0051/C0049/C0049 SBOS230A – MARCH 2002 – REVISED JUNE 2002 www.ti.com PACKAGE DRAWING
Orderable Device Status(1) Package Type Package Drawing Pins Package Qty Eco Plan(2) Lead/Ball FinishMSL Peak Temp (3) PGA4311U ACTIVE SOIC DW 28 28 Green (RoHS & no Sb/Br) CU NIPDAU Level-2-260C-1 YEAR PGA4311U/1K ACTIVE SOIC DW 28 1000 Green (RoHS & no Sb/Br) CU NIPDAU Level-2-260C-1 YEAR PGA4311U/1KG4 ACTIVE SOIC DW 28 1000 Green (RoHS & no Sb/Br) CU NIPDAU Level-2-260C-1 YEAR PGA4311U2 PREVIEW SOIC DW 28 1 TBD Call TI Call TI PGA4311UA ACTIVE SOIC DW 28 28 Green (RoHS & no Sb/Br) CU NIPDAU Level-2-260C-1 YEAR PGA4311UA/1K ACTIVE SOIC DW 28 1000 Green (RoHS & no Sb/Br) CU NIPDAU Level-2-260C-1 YEAR PGA4311UA/1KG4 ACTIVE SOIC DW 28 1000 Green (RoHS & no Sb/Br) CU NIPDAU Level-2-260C-1 YEAR PGA4311UA1 PREVIEW SOIC DW 28 1 TBD Call TI Call TI PGA4311UAG4 ACTIVE SOIC DW 28 28 Green (RoHS & no Sb/Br) CU NIPDAU Level-2-260C-1 YEAR PGA4311UG4 ACTIVE SOIC DW 28 28 Green (RoHS & no Sb/Br) CU NIPDAU Level-2-260C-1 YEAR (1)The marketing status values are defined as follows: ACTIVE: Product device recommended for new designs. LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect. NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design. PREVIEW: Device has been announced but is not in production. Samples may or may not be available. OBSOLETE: TI has discontinued the production of the device. (2)Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check http://www.ti.com/productcontentfor the latest availability information and additional product content details. TBD: The Pb-Free/Green conversion plan has not been defined. Pb-Free (RoHS):TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements for all 6 substances, including the requirement that lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes. Pb-Free (RoHS Exempt):This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and package, or 2) lead-based die adhesive used between the die and leadframe. The component is otherwise considered Pb-Free (RoHS compatible) as defined above. Green (RoHS & no Sb/Br):TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame retardants (Br or Sb do not exceed 0.1% by weight in homogeneous material) (3) MSL, Peak Temp. -- The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature. Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals. TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release. In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis. PACKAGE OPTION ADDENDUM www.ti.com 8-Jan-2007 Addendum-Page 1
Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications, enhancements, improvements, and other changes to its products and services at any time and to discontinue any product or service without notice. Cu stomers should obtain the latest relevant information before placing orders and should verify that such info rmation is current and complete. All products are sold subject to TI’s terms and conditions of sale supplied at the time of order acknowledgment. TI warrants performance of its hardware products to the specifications applicable at the time of sale in accordance with TI’s standard warranty. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where mandated by governm ent requirements, testing of all parameters of each product is not necessarily performed. TI assumes no liability for applications assistance or customer product design. Customers are responsible for their products and applications using TI component s. To minimize the risks associated with customer products and applications, customers should provide adequate design and operating safeguards. TI does not warrant or represent that any license, either express or implie d, is granted under any TI patent right, copyright, mask work right, or other TI intellectual property right relating to any combination, machine, or process in which TI products or services are us ed. Information published by TI regarding third-party products or services does not consti tute a license from TI to use such products or services or a warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the third party, or a license from TI under the pat ents or other intellectual property of TI. Reproduction of information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied by all associated warranties, conditions, lim itations, and notices. Reproduction of this information with alteration is an unfair and deceptive business practice. TI is not responsible or liable for such altered documentation. Resale of TI products or services with statements diffe rent from or beyond the parameters stated by TI for that product or service voids all express and any imp lied warranties for the associated TI product or service and is an unfair and deceptive business practice. TI is not responsible or liable for any such statements. Following are URLs where you can obtain information on other Texas Instruments products and application solutions: Products Applications Amplifiers amplifier.ti.c om Audio www.ti.com/audio Data Converters dataconverter.ti.co m Automotive www.ti.com/automotive DSP dsp.ti.com Broadband www.ti.com/broadband Interface interface.ti.com Digital Control www.ti.com/digitalcontrol Logic logic.ti.com Military www.ti.com/military Power Mgmt power.ti.com Optical Networking www.ti.com/opticalnetwork Microcontrollers microcontroller.ti.com Security www.ti.com/security Low Power Wireless www.ti.com/lpw Telephony www.ti.com/telephony Video & Imaging www.ti.com/video Wireless www.ti.com/wireless Mailing Address: Texas Instruments Post Office Box 6553 03 Dallas, Texas 75265 Copyright © 2007, Texas Instruments Incorporated