PG1096NL PULSE | Alldatasheet

Document overview

  • Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
  • PDF pages: 3

Technical content

P745.D (08/16) pulseelectronics.com SMT Power Inductors Round wire Coils– PG1096NL series Inductance Range: 1.5uH to 82uH Current Rating: up to 65Apk Footprint: 26mm x 26mm Max Height: 14.8mm Max No Thermal Aging RoHS Compliant Electrical Specifications @ 25°C - Operating Temperature -40°C to 130°C1 Part Number Inductance @ Irated2 µH TYPICAL Irated 3 (A) Controlled Electrical Specs. Saturation 5 Current Isat (A TYP) Heating Current 6 Idc (A TYP) Core Loss Factor 7 (K2) DCR 4 (mΩ) MAX Inductance @ 0Adc (µH ± 20%) 25°C 100°C PG1096.252NL 2.25 45 1.2 2.5 55 43 45 31 PG1096.682NL 6 30 2 6.8 35 27 .5 30 50.6 PG1096.473NL 42.3 11 12.5 47 13 10 11 134.4 1. Actual temperature of the component during system operation (ambient plus temperature rise) must be within the standard operating range. 2. Inductance at Irated is a typical inductance value for the component taken at rated current. 3. The rated current as listed is either the saturation current (@ 25°C) or the heating current depending on which value is lower. 4. The DCR of the part is measured at an ambient temperature of 20°C±3°C from point a to b as shown below on the mechanical drawing. 5. The saturation current, Isat, is the current at which the component inductance drop by 20% (typical) at an ambient temperature. This current is determined by placing the component in the specified ambient environment and applying a short duration pulse current (to eliminate self-heating effect) to the component. 6. The heating current, Idc, is the DC current required to raise the component tempera- ture by approximately 40°C. The heating current is determined by mounting the component on a typical PCB and applying current for 30 minutes. The temperature is measured by placing the thermocouple on top of the unit under test. Take note that the components’ performance varies depending on the system condition. It is sug- gested that the component be tested at the system level, to verify the temperature rise of the component during system operation. 7. Core loss approximation is based on published core data: Core Loss = K1 * (f)1.42 * (K2ΔI)2.57 in mW K1=2.86E-09 (2.50E-09 FOR PG1096.152NL) f = switching frequency in KHz K1 & K2 = core loss factors ΔI= delta I across the component in Ampere K2ΔI=one half of the peak to peak flux density across the component in Gauss 8. Unless otherwise specified, all testing is made at 100kHz, 0.1Vac 9. Optional Tape & Reel packaging can be ordered by adding a “T” suffix to the part standard tape and reel specification EIA481. The tape and reel for this product has a width (W=44.0mm), pitch (Po=36.0mm) and depth (Ko=15.6mm). 10. The core is a conductive material so care should be taken when mounting this com- ponent over an exposed via or if the voltage across the terminals exceeds 24V. Trickle current through the core material may generate additional losses and potential overheating. Please contact Pulse to discuss an alternative solution if required. Notes:

P745.D (08/16) pulseelectronics.com SMT Power Inductors Round wire Coils– PG1096NL series Mechanicals PG1096.XXXNL Schematic Inches mmDimensions: 0.01 0.25Unless otherwise specified, all tolerences are ± (28.0 grams for PG1096.152NL) *PIN 3 IS FOR MECHANICAL SUPPORT ONLY AND HAS NO INTERNAL ELECTRICAL CONNECTION Part Number Lead Width (X) Ref H (Height) P (Pin Pitch) PG1096.152NL 3.0mm 13mm 17.00±1.00mm PG1096.252NL 3.0mm 14.8mm PG1096.472NL 3.0mm PG1096.682NL 3.0mm PG1096.103NL 3.0mm PG1096.183NL 3.0mm PG1096.223NL 3.0mm PG1096.333NL 3.0mm PG1096.473NL 3.0mm PG1096.683NL 3.0mm PG1096.823NL 2.3mm 17.00±1.70mm

P745.D (08/16) pulseelectronics.com SMT Power Inductors Round wire Coils– PG1096NL series Inductance Charts PG1096.XXXNL Typical Inductance vs DC Bias 01 02 03 04 05 06 07 08 0 DC Bias (A) INDUCTANCE(uH) .152NL@25ºC .152NL@100ºC .252NL@25ºC .252NL@100ºC .472NL@25ºC .472NL@100ºC .682NL@25ºC .682NL@100ºC .103NL@25ºC .103NL@100ºC Typical Inductance vs DC Bias 05 10 15 20 25 DC Bias (A) INDUCTANCE(uH) .183NL@25ºC .183NL@100ºC .223NL@25ºC .223NL@100ºC .333NL@25ºC .333NL@100ºC .473NL@25ºC .473NL@100ºC .683NL@25ºC .683NL@100ºC .823NL@25ºC .823NL@100ºC For More Information Pulse Worldwide Headquarters

12220 World Trade Drive

San Diego, CA 92128 U.S.A. Tel: 858 674 8100 Fax: 858 674 8262 Pulse Europe Pulse Electronics GmbH Am Rottland 12

58540 Meinerzhagen

Tel: 49 2354 777 100 Fax: 49 2354 777 168 Pulse China Headquarters B402, Shenzhen Academy of Aerospace Technology Bldg. 10th Kejinan Road High-Tech Zone Nanshan District Shenzhen, PR China 518057 Tel: 86 755 33966678 Fax: 86 755 33966700 Pulse North China Room 2704/2705 Super Ocean Finance Ctr.

2067 Yan An Road West

Tel: 86 21 62787060 Fax: 86 2162786973 Pulse South Asia

135 Joo Seng Road

#03-02 PM Industrial Bldg. Singapore 368363 Tel: 65 6287 8998 Fax: 65 6287 8998 Pulse North Asia 3F, No. 198 Zhongyuan Road Zhongli City Taoyuan County 320 Taiwan R. O. C. Tel: 886 3 4356768 Fax: 886 3 4356823 (Pulse) Fax: 886 3 4356820 (FRE) Performance warranty of products offered on this data sheet is limited to the parameters specified. Data is subject to change without notice. Other brand and product names mentioned herein may be trademarks or registered trademarks of their respective owners. © Copyright, 2016. Pulse Electronics, Inc. All rights reserved.