PG0926.461NL PULSE | Alldatasheet
Document overview
- Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
- PDF pages: 3
Technical content
P700.A (05/15) pulseelectronics.com SMT Power Inductor Round Wire Coils - PG0926NL series Inductance Range: 0.46µH to 22.0µH Current Rating: up to 50Apk Footprint: 13.4mm x 13.4mm Max Height: 8.0mm Max No Thermal Aging USA 858 674 8100 Germany 49 7032 7806 0 Singapore 65 6287 8998 Shanghai 86 21 62787060 China 86 755 33966678 Taiwan 886 3 4356768 Electrical Specifications @ 25°C - Operating Temperature -40°C to 130°C¹ Part Number Inductance @ Irated² µH TYPICAL Irated ³ (A) CONTROLLED ELECTRICAL SPECS SATURATION5 CURRENT Isat (A TYP) HEATING6 CURRENT Idc (A TYP) CORE LOSS7 FACTOR (K2)DCR4 (mΩ) ±12% INDUCTANCE @0Adc Notes: 1. Actual temperature of the component during system operation (ambient plus temperature rise) must be within the standard operating range. 2. Inductance at Irated is a typical inductance value for the component taken at rated current. 3. The rated current listed is either the saturation current (@ 25°C) or the heating current depending on which value is lower. 4. The DCR of the part is measured at an ambient temperature of 20°C ± 3°C from point a to b as shown below on the mechanical drawing. 5. The saturation current, Isat, is the current at which the component inductance drop by 20% (typical) at an ambient temperature. This current is determined by placing the component in the specified ambient environment and applying a short duration pulse current (to eliminate self-heating effect) to the component. 6. The heating current, Idc, is the DC current required to raise the component temperature by approximately 40°C. The heating current is determined by mounting the component on a typical PCB and applying current for 30 minutes. The temperature is measured by placing the thermocouple on top of the unit under test. Take note that the components’ performance varires depending on the system condition. It is suggested that the component be tested at the system level, to verify the temperature rise of the component during system operation. 7. Core loss approximation is based on published core data: Core Loss = K1 * (f)1.72 * (K2ΔI)2.41in mW K1 = 8.68E - 10 f = switching frequency in KHz K1 & K2 = core loss factors ΔI = delta I across the component in Ampere K2ΔI = one half of the peak to peak flux density across the component in Gauss 8. Unless otherwise specified, all testing is made at 100KHz, 0.1Vac 9. Optional Tape and Reel packaging can be ordered by adding a “T” suffix to the industry standard tape and reel specification EIA481. The tape and reel for this product has a width (W=32.0mm), pitch (Po=20.0mm) and depth (Ko=8.35mm).
P700.A (05/15) pulseelectronics.com SMT Power Inductor Round Wire Coils - PG0926NL series PG0926.XXXNL Mechanicals Schematics .094 [2.40] .087 [2.20] .323REF [8.20] BOTTOM VIEW .079REF [2.00] X (refer to table below) TOP VIEW .528 MAX [13.40 MAX] .528 MAX [13.40 MAX] PG0926.XXXNL MFG. LOCATION DATE CODE FRONT VIEW a b H MAX. .197REF [5.00] .197REF [5.00] .138REF [3.50] .157REF [4.00] SUGGESTED LAND PATTERN (REFERENCE ONLY) .323REF [8.20] .394REF [10.00] Dimensions: inched mm +.010 -0.25Unless otherwise specified, all tolerance are *Pin 3 is for mechanical support only and has no internal electrical connection SCHEMATIC Typical Inductance vs DC Bias 0.5 1.5 2.5 04 81 21 62 02 42 83 23 64 04 44 85 25 6 DC Bias (A) INDUCTANCE(uH) .461NL@25ºC .461NL@100ºC .102NL@25ºC .102NL@100ºC .182NL@25ºC .182NL@100ºC .282NL@25ºC .282NL@100ºC
pulseelectronics.com SMT Power Inductor Round Wire Coils - PG0926NL series P700.A (05/15) For More Information Pulse Worldwide Headquarters
12220 World Trade Drive
San Diego, CA 92128 U.S.A. Tel: 858 674 8100 Pulse Europe Einsteinstrasse 1 D-71083 Herren- berg Germany Tel: 49 7032 7806 Pulse China Headquarters B402, Shenzhen Academy of Aerospace Technol- ogy Bldg. 10th Kejinan Road High-Tech Zone Nanshan District Shenzen, PR China 518057 Pulse North China Room 2704/2705 Super Ocean Finance Ctr.
2067 Yan An Road
135 Joo Seng Road
#03-02 PM Industrial Bldg. Singapore 368363 Tel: 65 6287 8998 Fax: 65 6287 8998 Pulse North Asia 3F, No. 198 Zhongyuan Road Zhongli City Taoyuan County 320 Taiwan R. O. C. Tel: 886 3 4356768 Fax: 886 3 4356823 (Pulse) Performance warranty of products offered on this data sheet is limited to the parameters specified. Data is subject to change without notice. Other brand and product names mentioned herein may be trademarks or registered trademarks of their respective owners. © Copyright, 2015. Pulse Electronics, Inc. All rights reserved. Typical Inductance vs DC Bias 01234567 89 10 11 12 13 14 15 16 DC Bias (A) INDUCTANCE(uH) .562NL@25ºC .562NL@100ºC .722NL@25ºC .722NL@100ºC .872NL@25ºC .872NL@100ºC .113NL@25ºC .113NL@100ºC .153NL@25ºC .153NL@100ºC .223NL@25ºC .223NL@100ºC