DATASHEET SEARCH SITE | WWW.ALLDATASHEET.COM
Document overview
- Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
- PDF pages: 7
Technical content
Features
- Max Frequency 18 GHz 82.5% Phase V elocity T riple Shielded FEP Jacket Thermally Pre-Conditioned Cable Captivated Stainless Steel Connectors Expanded PTFE dielectric J-STD-Soldering Lot T raceability T est Report Ship same day JACKET .160 [4.06] OUTER BRAID INNER SHIELD INNER BRAID DIELECTRIC SOLID CENTER CONDUCTOR SECTION VIEW
Applications
- General Purpose Laboratory Use High Reliability
- Extreme T emperatures Military Electronics A vionics
- IFF SA TCOM ECM
Description
Pasternack’s temperature conditioned low loss cable assemblies are part of our full line of reliable RF components avail- able for shipment same day. These commercial-off-the-shelf (COTS), RF / microwave cable assemblies are designed and processed with high reliability in mind. Captivated stainless steel cable assembly connectors and thermally pre-conditioned triple-shielded coaxial cable are assembled using J-STD soldering processes and WHMA-A-620 workmanship criteria. The combination of stable materials, processing and acceptance testing work together to create a dependable cable assembly for applications where performance over time is important or the cost of failure is high. Each finished COTS temperature condi - tioned low loss cable assembly is traceable to its component lots and a test report is available for every lot produced. Our highly reliable low loss conditioned RF cable assembly datasheet specifications and drawing with dimensions are shown below in this PDF. Pasternack’s broad catalog of RF, microwave and millimeter wave cable assemblies allow designers to configure and customize their signal connections however they like. Whether the need is to provide reliable stable connections or fielding dependable RF cables, Pasternack has the right cable assemblies for the job. Pasternack can also expertly build your custom cable assemblies for you and ship them same day. Referenced Specifications IPC/WHMA-A-620 Requirements and Acceptance for Cable and Wire Harness Assemblies MIL-STD-348 Radio Frequency Connector Interfaces for MIL-DTL-3643, MIL-DTL-3650, MIL-DTL-3655, MIL- DTL-25516, MIL-PRF-31031, MIL-PRF-39012, MIL-PRF-49142, MIL-PRF... IPC J-STD-001 Requirements for Soldered Electrical and Electronic Assemblies IPC J-STD-006 Requirements for Electronic Grade Solder Alloys and Fluxed and Non-Fluxed Solid Solders for Electronic Soldering Applications Click the following link (or enter part number in “SEARCH” on website) to obtain additional part information including price, inventory and certifications: Temperature Conditioned SMA Male to N Male Low Loss Cable Using PE-P160LL Coax PE3M0186 PE3M0186 REV 1.2 Temperature Conditioned SMA Male to N Male Low Loss Cable Using PE-P160LL Coax RF Cable Assemblies Technical Data Sheet PE3M0186
any representation or warranty regarding the suitability of the part described herein for any particular purpose, and Pasternack does not assume any liability arising out of the use of any part or documentation. SAE AS5942 Marking of Electrical Insulating Materials SAE AS23053 Insulation Sleeving, Electrical, Heat Shrinkable, General Specifications For Material Specifications Component Specification Cable PE-P160LL in accordance with PE-P160LL datasheet Connector 1 PE45440 in accordance with MIL-STD-348 Connector 2 PE45446 in accordance with MIL-STD-348 Heat Shrink 1 SUMITUBE W3B2(4X) SIZE 12/3 in accordance with SAE AS23053 (AS APPLICABLE) Heat Shrink 2 SUMITUBE W3B2(4X) SIZE 12/3 in accordance with SAE AS23053 (AS APPLICABLE) Heat Shrink 3 M23053/4-303-0 in accordance with SAE AS23053 Heat Shrink 4 M23053/4-303-0 in accordance with SAE AS23053 Solder SN63 in accordance with J-STD-006 Electrical Specifications Description Minimum T ypical Maximum Units Frequency Range DC 18 GHz VSWR 1.35:1 Velocity of Propagation 82.5 % Capacitance 25 [82.02] pF/ft [pF/m] Dielectric Withstanding Voltage (AC) 1,000 V rms Specifications by Frequency Description F1 F2 F3 F4 F5 Units Frequency 1 2 4.5 9 18 GHz Electrical Specification Notes: Insertion Loss does not include the loss of the connectors. Insertion Loss is estimated as 0.04*SQRT(FGHz) dB per connector. PE3M0186 REV 1.2 Click the following link (or enter part number in “SEARCH” on website) to obtain additional part information including price, inventory and certifications: Temperature Conditioned SMA Male to N Male Low Loss Cable Using PE-P160LL Coax PE3M0186 RF Cable Assemblies Technical Data Sheet PE3M0186 Temperature Conditioned SMA Male to N Male Low Loss Cable Using PE-P160LL Coax
any representation or warranty regarding the suitability of the part described herein for any particular purpose, and Pasternack does not assume any liability arising out of the use of any part or documentation. Mechanical Specifications Cable Assembly Description Minimum T ypical Maximum Units Cable Outer Diameter 0.155 0.16 0.165 in Weight 0.15 [68.04] lbs [g] Cable Characteristics Description Specification Cable Type PE-P160LL Impedance 50 Ohms Inner Conductor Type Solid Inner Conductor Material and Plating Copper , Silver Dielectric Type Expanded PTFE Tape Number of Shields 3 Shield Layer 1 Silver Plated Copper Shield Layer 2 Aluminum Polyester Shield Layer 3 Silver Plated Copper Wire Jacket Material FEP PE3M0186 REV 1.2 Click the following link (or enter part number in “SEARCH” on website) to obtain additional part information including price, inventory and certifications: Temperature Conditioned SMA Male to N Male Low Loss Cable Using PE-P160LL Coax PE3M0186 RF Cable Assemblies Technical Data Sheet Temperature Conditioned SMA Male to N Male Low Loss Cable Using PE-P160LL Coax PE3M0186
any representation or warranty regarding the suitability of the part described herein for any particular purpose, and Pasternack does not assume any liability arising out of the use of any part or documentation. Connector Characteristics Description Connector 1 Connector 2 Type SMA Male N Male Specification MIL-STD-348 MIL-STD-348 Impedance 50 Ohms 50 Ohms Contact Material and Plating Beryllium Copper , Gold over Nickel Beryllium Copper , Gold over Nickel Contact Plating Specification 50 µin minimum 50 µin minimum Dielectric Type PTFE PTFE Body Material and Plating Passivated Stainless Steel Passivated Stainless Steel Body Plating Specification SAE-AMS-2700 SAE-AMS-2700 Coupling Nut Material and Plating Passivated Stainless Steel Passivated Stainless Steel Coupling Nut Plating Specification SAE-AMS-2700 SAE-AMS-2700 Hex Size 5/16 inch 3/4 inch Seal Gasket Material Silicone Rubber Silicone Rubber Contact Gage Specification 0.000 in min 0.210 in min Insulator Gage Specification 0.000 in min Mechanical Specification Notes: Environmental Specifications Description Specification Temperature Operating Range -55 to +125 deg C Compliance Certifications (see product page for current document) Process Specifications Process Specification Cable Preconditioning 5 cycles, -55 °C to +125°C, 20 minute dwells Soldering in accordance with J-STD-001, class 3 Marking shall meet the adherence requirements of SAE AS5942 Workmanship shall be in accordance with IPC/WHMA-A-620, class 3 PE3M0186 REV 1.2 Click the following link (or enter part number in “SEARCH” on website) to obtain additional part information including price, inventory and certifications: Temperature Conditioned SMA Male to N Male Low Loss Cable Using PE-P160LL Coax PE3M0186 RF Cable Assemblies Technical Data Sheet Temperature Conditioned SMA Male to N Male Low Loss Cable Using PE-P160LL Coax PE3M0186
any representation or warranty regarding the suitability of the part described herein for any particular purpose, and Pasternack does not assume any liability arising out of the use of any part or documentation. Tests and Inspections Description Sampling Connector Gaging (pin and insulator position) 100% Insertion Loss 100% VSWR 100% Dielectric Withstanding Voltage (DWV) 100% Visual - workmanship, configuration and marking 100% Length C=0, 1.5 AQL Mass C=0, 1.5 AQL Plotted and Other Data Notes:
- Values at 25°C, sea level. Typical Performance Data -1000 -700 -400 -100 200 500 800 1100 1400 1700 2000 -55 -35 -15 5 25 45 65 85 105 125 PPM ° C Typical Phase Change vs Temperature PE-P160LL Cable PE3M0186 REV 1.2 Click the following link (or enter part number in “SEARCH” on website) to obtain additional part information including price, inventory and certifications: Temperature Conditioned SMA Male to N Male Low Loss Cable Using PE-P160LL Coax PE3M0186 RF Cable Assemblies Technical Data Sheet Temperature Conditioned SMA Male to N Male Low Loss Cable Using PE-P160LL Coax PE3M0186
any representation or warranty regarding the suitability of the part described herein for any particular purpose, and Pasternack does not assume any liability arising out of the use of any part or documentation. How to Order Part Number Configuration: PE3M0186 - xx uu | | | Unit of Measure: | | cm = Centimeters | | <blank> = Inches | Length | Base Number Example: PE3M0186-12 = 12 inches long cable PE3M0186-100cm = 100 cm long cable Cable Assembly Length Tolerances: Temperature Conditioned SMA Male to N Male Low Loss Cable Using PE-P160LL Coax from Pasternack Enterprises has same day shipment for domestic and International orders. Our RF, microwave and millimeter wave products maintain a 99.4% availability and are part of the broadest selection in the industry. Click the following link (or enter part number in “SEARCH” on website) to obtain additional part information including price, inventory and certifications: Temperature Conditioned SMA Male to N Male Low Loss Cable Using PE-P160LL Coax PE3M0186 URL: https://www.pasternack.com/temperature-conditioned-sma-male-n-male-pe-p160ll-cable-assembly-pe3m0186-p.aspx PE3M0186 REV 1.2 RF Cable Assemblies Technical Data Sheet Temperature Conditioned SMA Male to N Male Low Loss Cable Using PE-P160LL Coax PE3M0186
any representation or warranty regarding the suitability of the part described herein for any particular purpose, and Pasternack does not assume any liability arising out of the use of any part or documentation. 7PE3M0186 REV 1.2 LENGTH MEASURED FROM REF. PLANE TO REF. PLANE .110 2.79 REF. .312 HEX .281 [7.14] FLATS PE45440 SMA MALE 3/4 HEX PE-P160LL .343 [8.71] FLATS RP RP J.Garcia APPROVED 01/30/19 DATE INITIAL RELEASE A REV. REVISIONS NOTES: ALL BLACK HEAT SHRINK WITH WHITE MARKINGS.1. TOP LAYER: SUMITUBE W3B2 (4X) - SIZE 12/32. BOTTOM LAYER: M23053/4-303-0. PASTERNACK SN XXXX PE3M0186-XXX D/C WWYYP1 CAGE 53919 PE45446 N MALE PART NUMBER N/A 1 1 REV UNLESS OTHERWISE SPECIFIED LEADING DIMENSIONS ARE INCHES DIMENSIONS IN [ ] ARE MILLIMETERS CAGE 53919 SIZE SCALE THESE COMMODITIES, TECHNOLOGY OR SOFTWARE WERE EXPORTED FROM THE UNITED STATES IN ACCORDANCE WITH THE EXPORT ADMINISTRATION REGULATIONS. DIVERSION CONTRARY TO U.S. LAW PROHIBITED. A SHEET OF THIRD-ANGLE PROJECTION DRAWN BY ALL DIMENSIONS SHOWN ARE FOR REFERENCE ONLY. PE3M0186 A THE INFORMATION AND DESIGN IN THIS DOCUMENT IS THE PROPERTY OF PASTERNACK CORPORATION. ALL RIGHTS RESERVED. J.YOU TOLERANCES: .01 [ .25 ].XX=± .X=± .2 [5.08] FRACTIONS ± 1/32 ANGLES ± 1° Pasternack Enterprises, Inc. P.O.Box 16759, Irvine, CA 92623. Fax: 1.949.261.7451 www.pasternack.com │ e-mail: sales@pasternack.com T-Rev.A Temperature Conditioned SMA Male to N Male Low Loss Cable Using PE-P160LL Coax PE3M0186 CAD Drawing