PE240128WRF-001-HQ

PS240128WRF POWERTIP | Alldatasheet

Document overview

• Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
• PDF pages: 27

Technical content

Datasheet sections

• 1.1 Features
• 1.2 Mechanical Specifications
• 1.3 Absolute Maximum Ratings
• 1.4 DC Electrical Characteristics
• 1.5 Optical Characteristics
• 1.6 Backlight Characteristics
• 2.2 Interface Pin Description
• 2.3 Timing Characteristics
• 3.1 Quality Assurance Flow Chart
• 3.2 Inspection Specification
• 4.1 Reliability Test Condition
• 5.1 Safety

PE240128WRF-001-HQ VER.0 Page2 RECORDS OF REVISION Date Rev. Description Page Design by 2006/04/19 0 MASS PRODUCTION --- PETER Total：27 Page

PE240128WRF-001-HQ VER.0 Page4 1. SPECIFICATIONS

1.1 Features

Display Type 240 * 128 Dots LCD Type FSTN , Positive , Transflective Driver Condition LCD Modul e : 1/160 Duty , 1/10 Bias Viewing Direction 6 O’clock Backlight Type LED B/L Weight 50 g Interface Support 8 Bit Parallel interface with 8080 or 6800 series MPU & IIC serial interface Driver IC SITRONIX - ST7529-G

1.2 Mechanical Specifications

Outline Dimension 99.2 (L) * 64.2 (w) * 18.04 (H)(Max) mm Viewing Area 93.0 (L) * 49.0 (w) mm Active Area 82.775 (L) * 44.135 (w) mm Dot Size 0.32 (L) * 0.32 (w) mm Dot Pitch 0.345 (L) * 0.345 (w) mm Note : For detailed information please refer to LCM drawing

1.3 Absolute Maximum Ratings

Item Symbol Condition Min. Max. Unit Power Supply Voltage V DD - -0.5 5.0 V LCD Driver Supply Voltage V LCD -VSS - -0.5 +22 V Input Voltage V IN - -0.5 V DD + 0.5 V Operating Temperature T OP - -20 70 °C Storage Temperature T ST - -30 80 °C Storage Humidity H D Ta < 40 °C 20 90 %RH

PE240128WRF-001-HQ VER.0 Page5

1.4 DC Electrical Characteristics

VDD = 3.3 V ± 0.3 , VSS = 0 V , Ta = 25°C Item Symbol Condition Min. Typ. Max. Unit Logic Supply Voltage V DD - 3.0 3.3 3.6 V High-level Input Voltage V IH - 0.7V DD - V DD V Low-level Input Voltage V IL - V SS - 0.3V DD V High-level Output Voltage V OH - - - - V Low-level Input Voltage V OL - - - - V Supply Current I DD V DD = 3.3 V - 1.2 6.2 mA VOP Vo – Vss (-20°C) 14.0 14.1 14.2 V VOP Vo – Vss (25°C) *1 12.8 12.95 13.1 V LCM Driver Voltage VOP Vo – Vss (70°C) 11.7 11.8 11.9 V NOTE:*1 The VOP test point is Vo – Vss. NOTE:2 : Recommended Power Supply Combinations.

1.5 Optical Characteristics

LCD Panel: 1/160 Duty , 1/13 Bias , VLCD = 15.06 V Ta = 25°C Item Symbol Conditions Min. Typ. Max. Reference View Angle θ C>2.0 , ∅ = 270° -40° - +40° Note 1 Contrast Ratio CR θ = -5° , ∅ = 270° 2 2.8 - Note 3 Response Time(rise) Tr θ = -5° , ∅ = 270° - 135 ms 205 ms Response Time(fall) Tf θ = -5° , ∅ = 270° - 300 ms 450 ms Note 2

PE240128WRF-001-HQ VER.0 Page6 Note 1. Optical characteristics-2 Viewing angle Front (6H) φ=270° Rear (12H) φ=90° Right (3H) φ=0° Left (9H) φ=180° θL Viewing angle Top (θ=0°) θR

PE240128WRF-001-HQ VER.0 Page7 Note 2. Optical characteristics-3 Fig.2 Definition of response time Positive Type Selected waveformNo selected waveform No selected waveform 100% 90% 10% TfTr Transmittance Negative Type 100% 90% 10% TfTr No selected Selected waveformNo selected waveform Transmittance

PE240128WRF-001-HQ VER.0 Page8 Electrical characteristics-2 ※2 Drive waveform Vop: Drive voltage fF: Frame frequency 1/B: Bias fD: Drive frequency N: Duty (1) Selected waveform (2) Non- Selected waveform V Vop/B Vop/B V 1/fF 1/fD 32N32 Note: Frame frequency is defined as follows: Common side supply voltage peak - to - peak /2 = 1 period Vop/B 1/fF 1/fD 321N32 (1-2/B)Vop Vop/B (1-2/B)Vop

PE240128WRF-001-HQ VER.0 Page9 Note 3. : Definition of Vth Active voltage range View direction Drive waveform Transmittance ※1 Contrast ratio = (Brightness in OFF state) / (Brightness in ON state) Outline of Electro-Optical Characteristics Measuring System Measuring System: Autronic DMS-803 50% (No selected waveform) 73% Vth2 40° (Selected waveform) Vth1 10° Selected waveform No selected waveform DriveVth2Vth1 Transmittanc 100 73% 50% 正讀 θ ψ Human Photo Detector LCD Panel Transmissive Temperatur e Control Chamber Active

PE240128WRF-001-HQ VER.0 Page10

1.6 Backlight Characteristics

LCD Module with LED Backlight Maximum Ratings Item Symbol Conditions Min. Max. Unit Forward Current IF Ta =25℃ - 180 mA Reverse Voltage VR Ta =25℃ - 5 V Power Dissipation PO Ta =25℃ - 0.61 W Electrical / Optical Characteristics T a = 2 5 ℃ Item Symbol Conditions Min. Typ. Max. Unit Forward Voltage VF IF= 80 mA - 3.3 3.4 V Reverse Current IR VR= 5V - - 60 uA X 0.29 0.32 0.35 CIE Color Coordinate (With LCD) Y IF= 80 mA 0.35 0.38 0.41 Average Brightness (with LCD) *1 IV IF= 80 mA 30 50 - cd/m 2 Uniformity (With LCD)*2 △B IF= 80 mA 70 - - % Color White *1 This value will be changed while mass production. *2：△B=B(min) / B(max)

PE240128WRF-001-HQ VER.0 Page11 2. MODULE STRUCTURE

2.1 Counter Drawing

2.1.1 LCM Mechanical Diagram

• See Appendix

2.1.2 Block Diagram

240 * 128 DOTS LCD PANEL IC-ST7529 Please refer interface pin description for detail A K COM0 COM63 ……… COM127 COM64 COM0 COM63 ……… COM143 ……… COM80

PE240128WRF-001-HQ VER.0 Page12

2.2 Interface Pin Description

Pin No. Symbol Function 1 A0 Register select input pin − A0 = "H": DB0 to DB8 or SI are display data − A0 = "L": DB0 to DB8 or SI are control data

2 RW_WR

Read / Write execution control pin MPU Type RW_WR Description

6800 RW Read / Write control input pin

RW = “H” : read RW = “L” : write 8080 /WR Write enable clock input pin The data on DB0 to DB8 are latched at the rising edge of the /WR signal.

3 DB0

4 DB1

5 DB2

6 DB3

They connect to the standard 8-bit MPU bus via the 8 bit bi-directional bus.When the following interface is selected and the XCS pin is high, the following pins become highimpedance, which should be fixed to VDD or VSS.

7 DB4

8 DB5

9 DB6

10 DB7

D7: SCL; D6: SI ; D0, D1: SA1, SA0 D3, D2: Acknowledgement D4, D5, D8 should be fixed to VDD or VSS.

11 E_RD

Read / Write execution control pin MPU Type RW_WR Description

6800 E Read / Write control input pin

-RW = “H”: When E is “H”, DB0 to DB8 are in an output status. -RW = “L”: The data on DB0 to DB8 are latched at the falling edge of the E signal. 8080 /RD Read enable clock input pin When /RD is “L”, DB0 to DB8 are in an output status. 12 RST Reset input pin. When RST is “L”, initialization is executed.

PE240128WRF-001-HQ VER.0 Page13 Pin No. Symbol Function

13 IF1

14 IF3

IF1 IF3 MPU interface type H L 80 series 8-bit parallel L H 68 series 8-bit parallel L L IIC

15 XCS

Data/instruction I/O is enabled only when XCS is "L". When chip select is non-active, DB0 to DB8 may be high impedance.

16 VSS Power supply (VSS=0)

17 VDD Power supply (VDD=3.3V) 18 CAP7P DC / DC voltage converter. Connect a capacitor between this terminal and the CAP7P terminal. 19 CAP1N DC / DC voltage converter. Connect a capacitor between this terminal and the CAP1N terminal. 20 CAP5P DC / DC voltage converter. Connect a capacitor between this terminal and the CAP5P terminal. 21 CAP3P DC / DC voltage converter. Connect a capacitor between this terminal and the CAP3P terminal. 22 CAP1N DC / DC voltage converter. Connect a capacitor between this terminal and the CAP1N terminal. 23 CAP1P DC / DC voltage converter. Connect a capacitor between this terminal and the CAP1P terminal. 24 CAP2P DC / DC voltage converter. Connect a capacitor between this terminal and the CAP2P terminal. 25 CAP2N DC / DC voltage converter. Connect a capacitor between this terminal and the CAP2N terminal. 26 CAP4P DC / DC voltage converter. Connect a capacitor between this terminal and the CAP4P terminal. 27 CAP2N DC / DC voltage converter. Connect a capacitor between this terminal and the CAP2N terminal. 28 CAP6P DC / DC voltage converter. Connect a capacitor between this terminal and the CAP6P terminal.

29 VLCD LCD supply voltage

PE240128WRF-001-HQ VER.0 Page14 Pin No. Symbol Function 30 V4 31 V3 32 V2 33 V1 34 V0 LCD driver supply voltages V0In & V0out should be connected together in FPC area. Voltages should have the following relationship: V0 ≧ V1 ≧ V2 ≧ V3 ≧ V4 ≧ VSS When the internal power circuit is active, these voltages are generated as the following table according to the state of LCD bias. LCD Bias V1 V2 V3 V4 1/N Bias (N-1) / N x V0 (N-2) / N x V0 (2/N) x V0 (1/N) x V0 NOTE: N = 5 to 14

PE240128WRF-001-HQ VER.0 Page15

2.3 Timing Characteristics

VDD = 3.3V , Ta = 25ºC Rating Item Signal Symbol Condition Min Max Units Address hold time t AH8 - 20 - Address setup time t AW8 - 20 - System cycle time tCYC8 - 200 - Enable L pulse width (Write) t CCLW - 100 - Enable H pulse width (Write) RW_WR tCCHW - 100 - Enable L pulse width (Read) t CCLR - 100 - Enable H pulse width (Read) E_RD tCCHR - 100 - WRITE Data setup time t DS8 - 150 - WRITE Address hold time t DH8 - 20 - READ access time tACC8 C L=100pF - 40 READ Output disable time DB0 to DB7 tOH8 C L=100pF - 30 ns

PE240128WRF-001-HQ VER.0 Page16 For the 6800 Series MPU VDD = 3.3V , Ta = 25ºC Rating Item Signal Symbol Condition Min Max Units Address hold time t AH6 - 20 - Address setup time t AW6 - 20 - System cycle time tCYC6 - 200 - Enable L pulse width (Write) t EWLW - 100 - Enable H pulse width (Write) RW_WR tEWHW - 100 - Enable L pulse width (Read) t EWLR - 100 - Enable H pulse width (Read) E_RD tEWHR - 100 - WRITE Data setup time t DS6 - 150 - WRITE Address hold time t DH6 - 20 - READ access time tACC6 C L=100pF - 40 READ Output disable time DB0 to DB7 tOH6 C L=100pF - 30 ns

PE240128WRF-001-HQ VER.0 Page17 Reset Timing VDD = 3.3V , Ta = 25ºC Rating Item Signal Symbol Condition Min Typ Max Units Reset time - t R - - 1 µs Reset “L” pulse width RES t RW - 1 - - µs

PE240128WRF-001-HQ VER.0 Page18

2.4 Display Command

PE240128WRF-001-HQ VER.0 Page19

PE240128WRF-001-HQ VER.0 Page20 3. QUALITY ASSURANCE SYSTEM

3.1 Quality Assurance Flow Chart

Item Customer Sales R&D Q.A Manufactu ring Product control Purchase Inventory control Marketing Design Sample Approval Pilot Run Mass Product Ship Out OK Request Info Survey Inquiry Project evaluation Project Validation Quote OK NG Contract Design check Sample test Verification Sample approval NG NG Pilot run & Reliabilit y test Verification Specification preparation OK Mass production Inspection NGOK Shipment NG Ship out OK

PE240128WRF-001-HQ VER.0 Page21 Item Customer Sales R&D Q.A Manufact uring Product control Purchase Inventory control Sales Service Q.A Activity 1. ISO 9001 Maintenance Activities 2. Process improvement proposal 3 . E q u i p m e n t c a l i b r a t i o n 4. Education And Training Activities 5. Standardization Management Info Claim Failure analysis Corrective action Tracking Analysis report

PE240128WRF-001-HQ VER.0 Page22

3.2 Inspection Specification

Inspection Standard : MIL-STD-105E Table Normal Inspection Single Sampling Level II Equipment : Gauge , MIL-STD , Powertip Tester , Sample IQC Defect Level : Major Defect AQL 0.4; Minor Defect AQL 1.5 FQC Defect Level : 100% Inspection OUT Going Defect Level : Sampling Specification : NO Item Specification Judge Level

1 Part Number The part number is inconsis tent with work order of

production N.G. Major

2 Quantity The quantity is inconsistent with work order of

production N.G. Major The display lacks of some patterns. N.G. Major Missing line. N.G. Major The size of missing dot, A is > 1/2 Dot size N.G. Major There is no function. N.G. Major Electronic characteristics of LCM A=( L + W ) ╱2 Output data is error N.G. Major Material is different with work order of production N.G. Major LCD is assembled in inverse direction N.G. Major Bezel is assembled in inverse direction N.G. Major Shadow is within LCD viewing area + 0.5 mm N.G. Major The diameter of dirty particle, A is > 0.4 mm N.G. Minor Dirty particle length is > 3.0mm, and 0.01mm < width ≤ 0.05mm N.G. Minor Display is without protective film N.G. Minor Conductive rubber is over bezel 1mm N.G. Minor Polarizer exceeds over viewing area of LCD N.G. Minor Area of bubble in polarizer, A > 1.0mm, the number of bubble is > 1 piece. N.G. Minor Appearance of LCD A=( L + W ) ╱ 2 Dirty particle (Including scratch、bubble ) 0.4mm < Area of bubble in polarizer, A < 1.0mm, the number of bubble is > 4 pieces. N.G. Minor Burned area or wrong part number is on PCB N.G. Major The symbol, character, and mark of PCB are unidentifiable. N.G Minor The stripped solder mask , A is > 1.0mm N.G. Minor 0.3mm < stripped solder mask or visible circuit, A < 1.0mm, and the number is ≥ 4 pieces N.G. Minor There is particle between the circuits in solder mask N.G Minor The circuit is peeled off or cracked N.G Minor There is any circuits risen or exposed. N.G Minor 0.2mm < Area of solder ball, A is ≤ 0.4mm The number of solder ball is ≥ 3 pieces N.G Minor Appearance of PCB A=( L + W ) ╱2 The magnitude of solder ball, A is > 0.4mm. N.G Minor

PE240128WRF-001-HQ VER.0 Page23 NO Item Specification Judge Level The shape of modeling is deformed by touching. N.G. Major Insufficient epoxy: Circuit or pad of IC is visible N.G. Minor Excessive epoxy: Diameter of modeling is > 20mm or height is > 2.5mm N.G. Minor6 Appearance of molding A=( L + W ) ╱2 The diameter of pinhole in modeling, A is > 0.2mm. N.G. Minor The folding angle of frame must be > 45°+ 10° N.G. Minor The area of stripped electroplate in top-view of frame, A is > 1.0mm. N.G. Minor Rust or crack is (Top view only) N.G. Minor7 Appearance of frame A=( L + W ) ╱2 The scratched width of frame is > 0.06mm. (Top view only) N.G. Minor The color of backlight is nonconforming N.G. Major Backlight can’t work normally. N.G. Major The LED lamp can’t work normally N.G. Major The unsoldering area of pin for backlight, A is > 1/2 solder joint area. N.G. Minor Electrical characteristic of backlight A=( L + W ) ╱2 The height of solder pin for backlight is > 2.0mm N.G. Minor The mark or polarity of component is unidentifiable. N.G. Minor The height between bottom of component and surface of the PCB is floating > 0.7mm N.G. Minor D > 1/4W W D D ’ P a d N.G. Minor End solder joint width, D’ is > 50% width of component termination or width of pad N.G. Minor Side overhang, D is > 25% width of component termination. N.G. Minor Component is cracked, deformed, and burned, etc. N.G. Minor The polarity of component is placed in inverse direction. N.G. Minor

10 Assembly parts

A=( L + W ) ╱2 Maximum fillet height of solder extends onto the component body or minimum fillet height is < 0.5mm. N.G. Minor

PE240128WRF-001-HQ VER.0 Page24 4. RELIABILITY TEST

4.1 Reliability Test Condition

1 High Temperature

Storage at 80 ± 2°C 96~100 hrs Surrounding temperature, then storage at normal condition 4hrs

2 Low Temperature

Storage at -30 ± 2°C 96~100 hrs Surrounding temperature, then storage at normal condition 4hrs

3 High Temperature

/Humidity Storage 1.Storage 96~100 hrs 60 ± 2°C, 90~95%RH surrounding temperature, then storage at normal condition 4hrs. (Excluding the polarizer).or 2.Storage 96~100 hrs 40 ± 2°C, 90~95%RH surrounding temperature, then storage at normal condition 4 hrs.

4 Temperature Cycling

(30mins) (5mins) (30mins) (5mins)

10 Cycle

5 Vibration 10~55Hz ( 1 minute ) 1.5mm X,Y and Z direction * (each 2hrs) Air Discharge: Apply 6 KV with 5 times discharge for each polarity +/- Contact Discharge: Apply 250V with 5 times discharge for each polarity +/-

6 ESD Test

Testing location: Around the face of LCD Testing location: 1.Apply to bezel. 2.Apply to Vdd, Vss. Packing Weight (Kg) Drop Height (cm) 0 ~ 45.4 122 45.4 ~ 90.8 76 90.8 ~ 454 61

7 Drop Test

PE240128WRF-001-HQ VER.0 Page25 5. PRECAUTION RELATING PRODUCT HANDLING

5.1 SAFETY

5.1.1 If the LCD panel breaks , be careful not to get the liquid crystal to touch your skin.

5.1.2 If the liquid crystal touches your ski n or clothes , please wash it off immediately by

using soap and water.

5.2 HANDLING

5.2.1 Avoid any strong mechani cal shock which can break the glass.

5.2.2 Avoid static electricity whic h can damage the CMOS LSI— When working with the

module , be sure to ground your body and any electrical equipment you may be using. 5.2.3 Do not remove the panel or frame from the module. 5.2.4 The polarizing plate of the display is very fragile. So , please handle it very carefully, do not touch , push or rub the exposed polarizing with anything harder than an HB pencil lead (glass , tweezers , etc.)

5.2.5 Do not wipe the polar izing plate with a dry cloth , as it may easily scratch the surface

of plate. 5.2.6 Do not touch the display area wi th bare hands , this will stain the display area. 5.2.7 Do not use ketonics solvent & arom atic solvent. Use with a soft cloth soaked with a cleaning naphtha solvent. 5.2.8 To control temperature and time of soldering is 280 ± 10°C and 3-5 sec.

5.2.9 To avoid liquid (include organic solvent) stained on LCM

5.3 STORAGE

5.3.1 Store the panel or module in a da rk place where the temperature is 25°C ± 5°C

and the humidity is below 65% RH. 5.3.2 Do not place the module near organics solvents or corrosive gases. 5.3.3 Do not crush , shake , or jolt the module.

5.4 TERMS OF WARRANTY

5.4.1 Applicable warrant period

The period is within thirteen months since the date of shipping out under normal using and storage conditions.

5.4.2 Unaccepted responsibility

This product has been manufactured to your company’s specification as a part for use in your company’s general electronic products. It is guaranteed to perform according to delivery specifications. For any other use apart from general electronic equipment, we cannot take responsibility if the product is used in nuclear power control equipment, aerospace equipment , fire and security systems or any other applications in which there is a direct risk to human life and where extremely high levels of reliability are required.