PD69008 MICROSEMI | Alldatasheet
Document overview
- Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
- PDF pages: 15
Technical content
PD69008 - 8 Ports Power Over Ethernet Manager Microsemi Analog Mixed Signal Group Page 1 2381 Morse Avenue, Irvine, CA 92614, USA; Within the USA: (800) 713-4113, Outside the USA: (949) 221-7100 Fax: (949) 756-0308 Copyright © 2009 Rev. 1.0, 2009-03-15 Microsemi’s PD69008 Power over Ethernet (PoE) Manager chip integrates power, analog and state of the art embedded core logic into a single 80-pin, plastic QFP package. The device is used in Ethernet switches and Midspans to enable network devices to share power and data over the same cable. PD69008 device is an 8-port, mixed-signal, high- voltage Power over Ethernet driver. It enables detection of IEEE802.3af-2003 compliant PDs (Powered Devices) and IEEE802.3AT High Power Devices, thus, ensuring safe power feeding and disconnection of ports. With full digital control via a serial communication interface and a minimum of external components, the device integrates into multi- port and highly populated Ethernet switches and routers. The PD69008 executes all real time functions as specified in the IEEE802.3af-2003 (“AF”) standard and IEEE802.3at High Power (“AT”) functionality, including load detection, “AF” and “AT” classification and port status monitoring. In addition it performs system level activities such as power management and MIB support for system management. The PoE device is designed to detect and disable disconnected ports, utilizing both DC and AC disconnection methods, as specified in the IEEE 802.3af-2003 standard. The PD69008 is designed to support 2 main configurations:
- Auto mode: For Basic ”AF” and “AT” PSE equipment
- Enhanced mode: For High End, Extended features set of AF and AT PSE equipment gate_3 Port_neg2 port_sense5 gate_4 port_sense4 Port_neg4 Port_neg3 port_sense3 gate_2 port_sense2 Port_neg1 gate_1 port_sense1 gate_5 AG ND1 Port_neg6 gate_6 gate_7 port_sense7 Port_neg7 NC NC NC NC NC NC NC port_sense6 AGND2 NC NC NC PD69008 Date Code17 gate_0 Port_neg5 NC DG ND1 Port_neg0 port_sense0 NC Vmain Ref_port_neg CP_OUT CP_IN Vport_pos0 Vport_pos1 Vport_pos2 Vport_pos3 Vport_pos4 Vport_pos5 Vport_pos6 Vport_pos7 NC NC NC NC DGND2 I2CINI Vcc2p5 QGND Ext_reg ASIC_INI ADC2p5 Iref Reset_n SCL SCK MOSI MISO SDA CS_n Vperi Disable_ports _n Sense_Neg CS_EEPROM_n/ LSL / Interrupt _n SDA_out / Test_mode Good0/GPIO0 Good1/GPIO1 rGood2/GPIO4 LSD / GPIO2 LSC / GPIO3 PD69008 Auto Mode features: ♦ Fully IEEE802.3af-2003 compliant ♦ Designed to support IEEE802.3at including two- event classification ♦ Supports pre-standard PD detection ♦ Supports Cisco devices detection ♦ IETF Power Ethernet MIB (RFC 3621) compliant ♦ Single DC voltage input (44v-57v) ♦ Wide temperature range: -40° C to +85° C ♦ Low thermal dissipation (0.5 Ω sense resistor) ♦ Drives 8 independent two-pairs power ports or 64-pairs ports ♦ Can cascade up to 8 PoE devices (64 ports) ♦ EEPROM interface for software patching and parameter configuration ♦ I 2C Host interface ♦ Supports Interrupt out pin ♦ Dynamic power management ♦ Emergency power management supporting three configurable Power Bank I/Os ♦ Direct register communication ♦ Direct LED drive supporting one or two colors ♦ Continuous monitoring per port and system data ♦ Parameter setting per port and per system ♦ Power soft start algorithm ♦ Thermal monitoring/protection ♦ Voltage monitoring/protection ♦ H/W disable ports input ♦ Built in 3.3 V regulator ♦ Internal power on reset ♦ Enhanced SPI bus for internal communication ♦ External EEPROM for system parameters update ♦ SW ROM patch option ♦ RoHS compliant Enhanced Modes Additional Features: ♦ I 2C or UART Host interface ♦ Serial communication protocol backwards compatible with PD63000 and PDIC66000 ♦ Added monitoring ♦ Extended parameters setting ♦ Port matrix for flexible PCB Layout ♦ Field upgradeable software ♦ Emergency Power Management with four power supplies Part number Temperature range Package PD69008 -40 to 85°C LQFP 80 pin This datasheet refers to ICs with date code "XAA0843" or later. Date code: See the bottom line (XAA0843) in the Pin Configuration drawing. Where “0843" is the date code, “08”IS the year (2008), and “43” is the week.
PD69008 - 8 Ports Power Over Ethernet Manager Microsemi Analog Mixed Signal Group Page 2 2381 Morse Avenue, Irvine, CA 92614, USA; Within the USA: (800) 713-4113, Outside the USA: (949) 221-7100 Fax: (949) 756-0308 Copyright © 2009 Rev. 1.0, 2009-03-15 The PD69008 is packed in an 80-pin LQFP plastic package, 12 x 12 x 1.4 mm with exposed pad Figure 1: PD69008 Package Description
PD69008 - 8 Ports Power Over Ethernet Manager Microsemi Analog Mixed Signal Group Page 3 2381 Morse Avenue, Irvine, CA 92614, USA; Within the USA: (800) 713-4113, Outside the USA: (949) 221-7100 Fax: (949) 756-0308 Copyright © 2009 Rev. 1.0, 2009-03-15 DGND, AGND, QGND, SENSE_NEG………….. -0.3 to 0.3 V (2) VCC MISO, MOSI, SCK, SCL, SDA, CLK, RESETN, CS_N, INTERRUPT, POWER_BANK[2..0], LSD, LSC, LSL, (VPERI + 0.3) V ESD (Human Body Model)…………….….… -2 to 2 kV (3) Max junction temperature (Tjunc)…………..…+150 °C Junction-ambient thermal resistance (θJA)….. 30 ° C/W(4) Junction-case thermal resistance (θJC)………10 ° C/W Lead temperature (soldering, 10 s)…………. 260 ° C Notes: “x” defines port numbers, 0 thru 3, inclusive. (1) 80 V is the transient voltage that can be applied for 1 min max. (2) Maximum value between grounds. (3) ESD testing is performed in accordance with the Human Body Model (CZap = 100 pF, RZap = 1500 Ω). (4) with 4ML PCB – no air flow Stresses beyond those listed above, may cause permanent damage to the device. Exposure to absolute maximum rating conditions for extended periods, may affect device reliability. PARAMETER MIN. NOM. MAX. UNIT Operating temperature At full load ambient -40 +85 ° C Operational limitations (1) 15 to 44 44 to 55 55 to 57 V (1) Operating functions depend on the input voltage, as shown in Figure 2. Figure 2: Operational Ranges
PD69008 - 8 Ports Power Over Ethernet Manager Microsemi Analog Mixed Signal Group Page 4 2381 Morse Avenue, Irvine, CA 92614, USA; Within the USA: (800) 713-4113, Outside the USA: (949) 221-7100 Fax: (949) 756-0308 Copyright © 2009 Rev. 1.0, 2009-03-15 PIN NAME: • SCL
- DISABLE_PORTS_N PAD TYPE: Schmitt Trigger CMOS input, TTL Level with no internal Res. PARAMETER SYMBOL MIN TYP MAX UNIT NOTE High Level Input Voltage V IH 2.0 V Low Level Input Voltage V IL 0.8 V Input Voltage Hysteresis 0.3 V Input High Current I IH -1 1 μA Input Low Current I IL -1 1 μA PIN NAME: • LSD Multiplexed with GPIO_2
- LSC Multiplexed with GPIO_3
- POWER_GOOD0 Multiplexed with GPIO_0
- POWER_GOOD1 Multiplexed with GPIO_1
- POWER_GOOD2 Multiplexed with GPIO_4 PAD TYPE: CMOS I/O, TTL Level with no internal pull up / pull down resistor, with Schmitt trigger Input PARAMETER SYMBOL MIN TYP MAX UNIT NOTE High Level Input Voltage V IH 2.0 V Low Level Input Voltage V IL 0.8 V Input Voltage Hysteresis 0.3 V Input High Current I IH -1 +1 μA Input Low Current I IL -1 +1 μA High Level Output Voltage VPERI- 0.4V V Iout=-2 mA Low Level Output Voltage 0.4 V Iout=2 mA
PD69008 - 8 Ports Power Over Ethernet Manager Microsemi Analog Mixed Signal Group Page 5 2381 Morse Avenue, Irvine, CA 92614, USA; Within the USA: (800) 713-4113, Outside the USA: (949) 221-7100 Fax: (949) 756-0308 Copyright © 2009 Rev. 1.0, 2009-03-15 PIN NAME: • SCK
- CS_N
- MOSI PAD TYPE: CMOS I/O, TTL Level with internal pull up current source, with Schmitt trigger Input PARAMETER SYMBOL MIN TYP MAX UNIT NOTE High Level Input Voltage V IH 2.0 V Low Level Input Voltage V IL 0.8 V Input Voltage Hysteresis 0.3 V Input High Current I IH -1 +1 μA Input Low Current I IL -1 +1 μA High Level Output Voltage VPERI- 0.4 V V Iout = -2 mA Low Level Output Voltage
0.4 V Iout = 2 mA
Pull up current 10 20 50 uA PIN NAME: • MISO PAD TYPE: CMOS I/O, TTL Level with internal pull up current source, with Schmitt trigger Input PARAMETER SYMBOL MIN TYP MAX UNIT NOTE High Level Input Voltage V IH 2.0 V Low Level Input Voltage V IL 0.8 V Input Voltage Hysteresis 0.3 V Input High Current I IH -1 +1 μA Input Low Current I IL -1 +1 μA High Level Output Voltage VPERI- 0.4V V Iout = -2 mA Low Level Output Voltage Pull down current 10 20 50 uA
PD69008 - 8 Ports Power Over Ethernet Manager Microsemi Analog Mixed Signal Group Page 6 2381 Morse Avenue, Irvine, CA 92614, USA; Within the USA: (800) 713-4113, Outside the USA: (949) 221-7100 Fax: (949) 756-0308 Copyright © 2009 Rev. 1.0, 2009-03-15 PIN NAME: • RESET_N
- SDA
- SDA_OUT Multiplexed with TEST_MODE PAD TYPE: Digital I/O – input/output open drain CMOS Open Drain Output with Schmitt Trigger Input, TTL Level (external pull up res. Only)) PARAMETER SYMBOL MIN TYP MAX UNIT NOTE High Level Input Voltage VIH 2.0 V Low Level Output Voltage VOL 0.4 V Iout = 6 mA Low Level Input Voltage VIL 0.8 V Input Voltage Hysteresis 0.3 V OFF State Output Current -1 +1 uA PIN NAME: • CS_EEPROM & LSL Multiplexed with INTERRUPT_N PAD TYPE: CMOS Open Drain Output (external pull up res. Only)) PARAMETER SYMBOL MIN TYP MAX UNIT NOTE Low Level Output Voltage
0.4 V Iout = 6 mA
-1 +1 uA PIN NAME: • VPORT_NEGx
- REF_PORT_NEG PAD TYPE: High Voltage Analog Pad PARAMETER SYMBOL MIN TYP MAX UNIT NOTE Pin Current Consumption -10 + 10 uA Port driver OFF, Vport differential measurement OFF, AC generator OFF
PD69008 - 8 Ports Power Over Ethernet Manager Microsemi Analog Mixed Signal Group Page 7 2381 Morse Avenue, Irvine, CA 92614, USA; Within the USA: (800) 713-4113, Outside the USA: (949) 221-7100 Fax: (949) 756-0308 Copyright © 2009 Rev. 1.0, 2009-03-15 PIN NAME: • PORT_SENSEx PAD TYPE: Low Voltage Analog Pad PARAMETER SYMBOL MIN TYP MAX UNIT NOTE Operating Voltage 0 0.5 V With external 0.5 Ohms 2% to GND Internal Current Consumption 20 uA PIN NAME: • VPORT_POSx
- VPORT_NEGx PAD TYPE: High Voltage Analog Pad PARAMETER SYMBOL MIN TYP MAX UNIT NOTE Operating Voltage (to GND) 0 62 V PIN NAME: • VMAIN PAD TYPE: High Voltage Supply Pad PARAMETER SYMBOL MIN TYP MAX UNIT NOTE Operating Voltage 44 57 V VMAIN Current Consumption 13.6 16 mA Total on VMAIN PIN NAME: • CP_OUT PAD TYPE: Analog PARAMETER SYMBOL MIN TYP MAX UNIT NOTE Operating voltage 44 68 V Pin Internal Current Consumption 5 mA
PD69008 - 8 Ports Power Over Ethernet Manager Microsemi Analog Mixed Signal Group Page 8 2381 Morse Avenue, Irvine, CA 92614, USA; Within the USA: (800) 713-4113, Outside the USA: (949) 221-7100 Fax: (949) 756-0308 Copyright © 2009 Rev. 1.0, 2009-03-15 PIN NAME: • CP_IN PAD TYPE: Analog PARAMETER SYMBOL MIN TYP MAX UNIT NOTE Operating Voltage 34 57 V PIN NAME: • ADC2p5, VCC2p5, VPERI, EXT_REG PAD TYPE: Analog PARAMETER SYMBOL MIN TYP MAX UNIT NOTE ADC2p5 Output Voltage 2.45 2.55 V ADC2p5 Internal Current Consumption 6 mA Recommended external cap. = 47 nF to 135 nF VCC2p5 Output Voltage 2.37 2. 62 V Recommended external cap. = 47 nF to 135 nF VPERI Output Voltage 3.10 3.5 V Recommended external cap. = 1 uF to 4.7 uF VPERI External Current Load 6 mA Without external NPN EXT_REG Output Current 6 mA PIN NAME: • ASICINI, I2CINI (max. capacitance between mode input to GND should NOT exceed 1nF) PAD TYPE: Analog PARAMETER SYMBOL MIN TYP MAX UNIT NOTE Operating Voltage 0 ADC2p5 V Current Consumption -1 +1 uA PIN NAME: • IREF PAD TYPE: Analog PARAMETER SYMBOL MIN TYP MAX UNIT NOTE Output Voltage 1.21 1.34 V With external 24.9 K resistor to GND
PD69008 - 8 Ports Power Over Ethernet Manager Microsemi Analog Mixed Signal Group Page 9 2381 Morse Avenue, Irvine, CA 92614, USA; Within the USA: (800) 713-4113, Outside the USA: (949) 221-7100 Fax: (949) 756-0308 Copyright © 2009 Rev. 1.0, 2009-03-15 PIN NAME: • FET_Gx PAD TYPE: Analog PARAMETER SYMBOL MIN TYP MAX UNIT NOTE Output voltage 12 15 V Dynamic Characteristics The PD69008 utilizes three programmable current level thresholds (Imin, Icut, Ilim) and three timers (Tmin, Tcut, Tlim). Loads that dissipate more than Icut for longer than Tcut are classified as ‘overloads’ and are automatically shutdown. Loads that consume Ilim current for more than Tlim are shutdown and classified as 'short circuit state'. In cases where the PD69008 is configured to operate in DC-Disconnect mode, and the output current is below Imin for more than Tmin , the PD is classified as ‘no-load’ and is shutdown. In cases where the PD69008 is configured to operate in AC-Disconnect mode, and the load's impedance is above a pre-defined impedance for more than Tmin, the PD is classified as ‘no-load’ and is shutdown. Automatic recovery from overload and no-load conditions is attempted every period of TOVLREC and TUDLREC (typically 5 and 1 seconds, respectively). Output power is limited to Ilim, which is a maximum peak current allowed at the port. AF Ports Parameters PARAMETER CONDITIONS MIN. TYP. MAX. UNIT Automatic recovery from overload shutdown TOVLREC value, measured from port shutdown (can be modified through control port) 5 s Automatic recovery from no-load shutdown TUDLREC value, measured from port shutdown (can be modified through control port) 1 s Cutoff timers accuracy Typical accuracy of T cut 4 2 0 ms Inrush current I Inrsh For t=50 ms, Cload=180 uF max. 400 450 mA Output current operating range I port Continuous operation after startup period. 10 375 mA Output power available, operating range Pport Continuous operation after startup period, at port output. 0.57 15.4 W Imin1 Must disconnect for t greater than T UVL 0 5 mA Off mode current Imin2 May or may not disconnect for t greater than TUVL 5 7.5 10 mA PD power maintenance request drop-out time limit TPMDO Buffer period to handle transitions 300 400 ms Over load current detection range I cut Time limited to T OVL 350 400 mA Over load time limit T OVL 50 75 ms Turn on rise time T rise From 10% to 90% of V port (Specified for PD load consisting of 100 uF capacitor in parallel to 200 Ω). 15 us Turn off time Toff From V port to 2.8 Vdc 500 ms Time Maintain Power Signature T MPS DC modulation time for dc disconnect 49 ms AC disconnect impedance Zac 27 600 2000 KΩ
PD69008 - 8 Ports Power Over Ethernet Manager Microsemi Analog Mixed Signal Group Page 10 2381 Morse Avenue, Irvine, CA 92614, USA; Within the USA: (800) 713-4113, Outside the USA: (949) 221-7100 Fax: (949) 756-0308 Copyright © 2009 Rev. 1.0, 2009-03-15 AT Ports Parameters PARAMETER CONDITIONS MIN. TYP. MAX. UNIT Automatic recovery from overload shutdown TOVLREC value, measured from port shutdown (can be modified through control port) 5 s Automatic recovery from no-load shutdown TUDLREC value, measured from port shutdown (can be modified through control port) 1 s Cutoff timers accuracy Typical accuracy of T cut 4 2 0 ms Inrush current I Inrsh For t=50 ms, Cload=180 uF max. 400 450 mA Output current operating range I port Continuous operation after startup period. 10 643 mA Output power available, operating range Pport Continuous operation after startup period, at port output. 0.57 36.25 W Imin1 Must disconnect for t greater than T UVL 0 5 mA Off mode current Imin2 May or may not disconnect for t greater than TUVL 5 7.5 10 mA PD power maintenance request drop-out time limit TPMDO Buffer period to handle transitions 300 400 ms Over load current detection range I cut Time limited to T OVL 686 728 771 mA Over load time limit T OVL 50 75 ms Turn on rise time T rise From 10% to 90% of V port (Specified for PD load consisting of 100 uF capacitor in parallel to 200 Ω). 15 us Turn off time Toff From V port to 2.8 Vdc 500 ms Time Maintain Power Signature TMPS DC modulation time for dc disconnect 49 ms AC disconnect impedance Zac 27 600 2000 K Ω
PD69008 - 8 Ports Power Over Ethernet Manager Microsemi Analog Mixed Signal Group Page 11 2381 Morse Avenue, Irvine, CA 92614, USA; Within the USA: (800) 713-4113, Outside the USA: (949) 221-7100 Fax: (949) 756-0308 Copyright © 2009 Rev. 1.0, 2009-03-15 Pin Pin Name [Package] Pin Type Description
0 PAD Gnd Exposed pad connected to underside of die
1 VPORT_POS0 Analog I/O Port 0 positive input
2 VPORT_POS1 Analog I/O Port 1 positive input
3 VPORT_POS2 Analog I/O Port 2 positive input
4 VPORT_POS3 Analog I/O Port 3 positive input
5 VPORT_POS4 Analog I/O Port 4 positive input
6 VPORT_POS5 Analog I/O Port 5 positive input
7 VPORT_POS6 Analog I/O Port 6 positive input
8 VPORT_POS7 Analog I/O Port 7 positive input
9 NC Not Connected
10 NC Not Connected
11 NC Not Connected
12 NC Not Connected
13 CP_OUT Analog I/O Charge Pump Output Pulse
14 CP_IN Su pply Charge pump input
15 VMAIN Su pply Main Voltage supply
16 REF_PORT_NEG Analog I/O Port negative reference
17 DGND2 GND Digital ground
18 POWER_GOOD0 MULTIPLEXED
WITH GPIO_0 Digital I/O Power supply monitoring Multiplexed with General purpose I/O
19 POWER_GOOD1 MULTIPLEXED
WITH GPIO_1 Digital I/O Power supply monitoring Multiplexed with General purpose I/O
20 POWER_GOOD2 MULTIPLEXED
WITH GPIO_4 Digital I/O Power supply monitoring Multiplexed with General purpose I/O
21 AGND1 GND Analog ground
22 VPORT_NEG6 Analog I/O Port 6 negative voltage feeding
23 PORT_SENSE6 Analog I/O Channel current monitoring
24 FET_G6 Analog I/O Port 6 – Gate control
25 FET_G7 Analog I/O Port 7 – Gate control
26 PORT_SENSE7 Analog I/O Channel current monitoring
27 VPORT_NEG7 Analog I/O Port 7 negative voltage feeding
28 NC Not Connected
29 NC Not Connected
30 NC Not Connected
31 NC Not Connected
32 NC Not Connected
33 NC Not Connected
34 NC Not Connected
35 NC Not Connected
36 NC Not Connected
37 NC Not Connected
38 NC Not Connected
39 NC Not Connected
40 DGND1 GND Digital ground
41 DISABLE_PORTS_N Di gital Input Disable All Ports Power – Active Low
42 CS_N Di gital I/O SPI bus, Chip Select
43 MISO Di gital I/O SPI bus, Master Data in/slave out
PD69008 - 8 Ports Power Over Ethernet Manager Microsemi Analog Mixed Signal Group Page 12 2381 Morse Avenue, Irvine, CA 92614, USA; Within the USA: (800) 713-4113, Outside the USA: (949) 221-7100 Fax: (949) 756-0308 Copyright © 2009 Rev. 1.0, 2009-03-15 Pin Pin Name [Package] Pin Type Description
44 MOSI Di gital I/O SPI bus, Master Data out/slave in
45 SCK Di gital I/O SPI bus, Serial clock I/O
46 SCL Di gital Input I2C bus, Serial Clock Input
47 SDA_OUT MULTIPLEXED WITH
TEST_MODE Digital I/O Third pin in I 2C protocol Test Mode Pin – Must be tied to VPERI with pull-up resistor if not used
48 SDA Di gital I/O I2C bus, open drain
49 RESET_N Di gital I/O Active Low Reset I/O
50 IREF Analog I/O Current reference
51 ASICINI Analog Input Analog input for Asic initialization
52 VCC2P5 Internal Regulator Internal 2.5v source – not to be used for external devices
53 I2CINI Analog Input Analog input for I2C initialization
54 QGND GND Quiet analog ground
55 ADC2P5 Internal reference ADC reference – not to be used for external
56 EXT_REG Analog Out External regulation
57 VPERI Analog Out Regulated 3.3v output voltage source for external devices
58 CS_EEPROM_N & LSL
MULTIPLEXED WITH INTERRUPT_N Digital Output Open drain SPI bus, EEPROM Chip Select & LED Stream Latch (if set) Multiplexed with interrupt out
59 LSD MULTIPLEXED WITH GPIO_2 Digital I/O LED Stream Data – data out Multiplexed with
60 LSC MUXED WITH GPIO_3 Digital I/O LED Stream CLK– CLK out Multiplexed with
61 SENSE_NEG Analog I/O Port sense reference
62 AGND2 GND Analog ground
63 VPORT_NEG0 Analog I/O Port 0 negative voltage feeding
64 PORT_SENSE0 Analog I/O Channel current monitoring
65 FET_G0 Analog I/O Port 0 – Gate control
66 FET_G1 Analog I/O Port 1 – Gate control
67 PORT_SENSE1 Analog I/O Channel current monitoring
68 VPORT_NEG1 Analog I/O Port 1 negative voltage feeding
69 VPORT_NEG2 Analog I/O Port 2 negative voltage feeding
70 PORT_SENSE2 Analog I/O Channel current monitoring
71 FET_G2 Analog I/O Port 2 – Gate control
72 FET_G3 Analog I/O Port 3 – Gate control
73 PORT_SENSE3 Analog I/O Channel current monitoring
74 VPORT_NEG3 Analog I/O Port 3 negative voltage feeding
75 VPORT_NEG4 Analog I/O Port 4 negative voltage feeding
76 PORT_SENSE4 Analog I/O Channel current monitoring
77 FET_G4 Analog I/O Port 4 – Gate control
78 FET_G5 Analog I/O Port 5 – Gate control
79 PORT_SENSE5 Analog I/O Channel current monitoring
80 VPORT_NEG5 Analog I/O Port 5 negative voltage feeding
PD69008 - 8 Ports Power Over Ethernet Manager Microsemi Analog Mixed Signal Group Page 15 2381 Morse Avenue, Irvine, CA 92614, USA; Within the USA: (800) 713-4113, Outside the USA: (949) 221-7100 Fax: (949) 756-0308 Copyright © 2009 Rev. 1.0, 2009-03-15 The information contained in the document is PROPRI ETARY AND CONFIDENTIAL information of Microsemi and cannot be copied, published, uploaded, posted, transmitt ed, distributed or disclosed or used without the express duly signed written consent of Microsemi If the recipient of this document has entered into a disclosure agreement with Microsemi, then the terms of su ch Agreement will also apply . This document and the information contained herein may not be modified, by any person other than autho rized personnel of Microsem i. No license under any patent, copyright, trade secret or other intellectual property right is granted to or conferred upon you by disclosure or delivery of the information, either expressly, by implication, inducemen t, estoppels or otherwise. Any license under such intellectual property rights must be approved by Microsemi in writing signed by an officer of Microsemi. Microsemi reserves the right to change the configuration, functionality and pe rformance of its products at anytime without any notice. This product has been subject to limited testing and should not be used in conjunction with life- support or other mission-critical equipment or applic ations. Microsemi assumes no liability whatsoever, and Microsemi disclaims any express or implied warranty, rela ting to sale and/or use of Microsemi products including liability or warranties relating to fitne ss for a particular purpose, merchantabili ty, or infringement of any patent, copyright or other intellectual property right. The product is subject to other terms and conditions which can be located on the web at http://www.microsemi.com/legal/tnc.asp
Revision History
Revision Level / Date Para. Affected Description 0.1 / 15 March 2009 - Initial Preliminary Release 1.0 / 25-Aug-09 Release © 2009 Microsemi Corp. All rights reserved. For technical support contact:sales_AMSG@microsemi.com. Cat. No. 06-0079-058