PD16707A_15 RENESAS | Alldatasheet

Document overview

  • Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
  • PDF pages: 15

Technical content

To our customers, Old Company Name in Catalogs and Other Documents On April 1st, 2010, NEC Electronics Corporation merged with Renesas Technology Corporation, and Renesas Electronics Corporation took over all the business of both companies. Therefore, although the old company name remains in this document, it is a valid Renesas Electronics document. We appreciate your understanding. Renesas Electronics website: http://www.renesas.com April 1st, 2010 Renesas Electronics Corporation Issued by: Renesas Electronics Corporation (http://www.renesas.com) Send any inquiries to http://www.renesas.com/inquiry.

  1. All information included in this document is current as of the date this document is issued. Such information, however, is subject to change without any prior notice. Before purchasing or using any Renesas Electronics products listed herein, please confirm the latest product information with a Renesas Electronics sales office. Also, please pay regular and careful attention to additional and different information to be disclosed by Renesas Electronics such as that disclosed through our website. 2. Renesas Electronics does not assume any liability for infringeme nt of patents, copyrights, or other intellectual property rights of third parties by or arising from the use of Renesas Electronics products or technical information described in this document. No license, express, implied or otherwise, is granted hereby under any patents, copyrights or other intellectual property rights of Renesas Electronics or others. 3. You should not alter, modify, copy, or otherwise misappropriate any Renesas Electronics product, whether in whole or in part. 4. Descriptions of circuits, software and other related informat ion in this document are provided only to illustrate the operation of semiconductor products and application examples. You are fully responsible for the incorporation of these circuits, software, and information in the design of your equipment. Renesas Electronics assumes no responsibility for any losses incurred by you or third parties arising from the use of these circuits, software, or information. 5. When exporting the products or technology described in this doc ument, you should comply with the applicable export control laws and regulations and follow the procedures required by such laws and regulations. You should not use Renesas Electronics products or the technology described in this document for any purpose relating to military applications or use by the military, including but not limited to the development of weapons of mass destruction. Renesas Electronics products and technology may not be used for or incorporated into any products or systems whose manufacture, use, or sale is prohibited under any applicable domestic or foreign laws or regulations. 6. Renesas Electronics has used reasonable care in preparing th e information included in this document, but Renesas Electronics does not warrant that such information is error free. Renesas Electronics assumes no liability whatsoever for any damages incurred by you resulting from errors in or omissions from the information included herein. 7. Renesas Electronics products ar e classified according to the following three quality grades: “Standard”, “High Quality”, and “Specific”. The recommended applications for each Renesas Electronics product depends on the product’s quality grade, as indicated below. You must check the quality grade of each Renesas Electronics product before using it in a particular application. You may not use any Renesas Electronics product for any application categorized as “Specific” without the prior written consent of Renesas Electronics. Further, you may not use any Renesas Electronics product for any application for which it is not intended without the prior written consent of Renesas Electronics. Renesas Electronics shall not be in any way liable for any damages or losses incurred by you or third parties arising from the use of any Renesas Electronics product for an application categorized as “Specific” or for which the product is not intended where you have failed to obtain the prior written consent of Renesas Electronics. The quality grade of each Renesas Electronics product is “Standard” unless otherwise expressly specified in a Renesas Electronics data sheets or data books, etc. “Standard”: Computers; office equipmen t; communications equipment; test and measurement equipment; audio and visual equipment; home electronic appliances; machine tools; personal electronic equipment; and industrial robots. “High Quality”: Transportation equi pment (automobiles, trains, ships, etc.); traffic control systems; anti-disaster systems; anti- crime systems; safety equipment; and medical equipment not specifically designed for life support. “Specific”: Aircraft; aerospace equipment; submersible repeaters; nuclear reactor control systems; medical equipment or systems for life support (e.g. artificial life support devices or systems), surgical implantations, or healthcare intervention (e.g. excision, etc.), and any other applications or purposes that pose a direct threat to human life. 8. You should use the Renesas Electronics pr oducts described in this document within the range specified by Renesas Electronics, especially with respect to the maximum rating, operating supply voltage range, movement power voltage range, heat radiation characteristics, installation and other product characteristics. Renesas Electronics shall have no liability for malfunctions or damages arising out of the use of Renesas Electronics products beyond such specified ranges. 9. Although Renesas Electronics endeavors to improve the quality and reliability of its products, semiconductor products have specific characteristics such as the occurrence of failure at a certain rate and malfunctions under certain use conditions. Further, Renesas Electronics products are not subject to radiation resistance design. Please be sure to implement safety measures to guard them against the possibility of physical injury, and injury or damage caused by fire in the event of the failure of a Renesas Electronics product, such as safety design for hardware and software including but not limited to redundancy, fire control and malfunction prevention, appropriate treatment for aging degradation or any other appropriate measures. Because the evaluation of microcomputer software alone is very difficult, please evaluate the safety of the final products or system manufactured by you. 10. Please contact a Renesa s Electronics sales office for details as to environmental matters such as the environmental compatibility of each Renesas Electronics product. Please use Renesas Electronics products in compliance with all applicable laws and regulations that regulate the inclusion or use of controlled substances, including without limitation, the EU RoHS Directive. Renesas Electronics assumes no liability for damages or losses occurring as a result of your noncompliance with applicable laws and regulations. 11. This document may not be reproduced or duplicated, in any form, in whole or in part, without prior written consent of Renesas Electronics. 12. Please contact a Renesa s Electronics sales office if you have any questions regarding the information contained in this document or Renesas Electronics products, or if you have any other inquiries. (Note 1) “Renesas Electronics” as used in this document means Renesas Electronics Corporation and also includes its majority- owned subsidiaries. (Note 2) “Renesas Electronics product(s)” means any product developed or manufactured by or for Renesas Electronics.

The information in this document is subject to change without notice. Before using this document, please confirm that this is the latest version. Not all products and/or types are available in every country. Please check with an NEC Electronics sales representative for availability and additional information. MOS INTEGRATED CIRCUIT µPD16707A 263/256-OUTPUT TFT-LCD GATE DRIVER DATA SHEET Document No. S16563EJ1V0DS00 (1st edition) Date Published January 2004 NS CP (K) Printed in Japan 2003 The mark ★ shows major revised points.

DESCRIPTION

The µPD16707A is a TFT-LCD gate driver equipped with 263/256-output lines. It can output a high-gate scanning voltage in response to CMOS level input because it provided with a level-shift circuit inside the IC circuit. It can also drive the XGA /SXGA/ SXGA+, and since the input signal is placed symmetrically, this product can wire easily between gate drivers.

FEATURES

  • CMOS level input (2.3 to 3.6 V)
  • 263/256 outputs
  • High-output voltage (VDD2 to VEE: 40 V MAX.)
  • Capable of All-ON outputting (/AOR, /AOL)
  • Input terminal symmetrical placement
  • Adapted to TCP/COF Remark /xxx indicates active low signal.

ORDERING INFORMATION

µ PD16707AN-xxx TCP (TAB package) µ PD16707ANL-xxx COF Remark Purchasing the above chip entail the exchange of documents such as a separate memorandum or product quality, and the TCP’s external shape is customized. To order the required shape, so please contact one of our sales representatives.

Data Sheet S16563EJ1V0DS 2 µ PD16707A 1. BLOCK DIAGRAM LS2 Note LS2 Note LS2 Note LS2 Note LS2 Note LS2 Note 263-bit shift registerSR1 SR263SR262SR261SR3SR2 R,/LR O 263O 262O 261O 3O 2O 1 VEE /AOR OER STVR CLKR STVL MODE CLKL OEL /AOL O 0 O 264 VEE level VEE level R,/LL Note LS2: Shifts CMOS level and output level (VDD2 to VEE).

Data Sheet S16563EJ1V0DS 3 µ PD16707A 2. PIN CONFIGURATION (µPD16707AN-xxx: TCP) (Copper Foil Surface, Face-up) IC View direction VDD2 VDD2 VDD1 VDD1 OEL O264 O263 O262 O261 CLKL VEE VEE VSS VSS MODE STVL R,/LL /AOL VDD2 VDD2 VDD1 VDD1 OER CLKR VEE VEE VSS VSS STVR R,/LR /AOR Chip back side Remark This figure does not specify the TCP package.

Data Sheet S16563EJ1V0DS 4 µ PD16707A 3. PIN FUNCTIONS Pin Symbol Pin Name I/O Description O1 to O263 Driver Output These pins output scan signals that dr ive the vertical direction (gate lines) of a TFT-LCD. The output signals change in synchronization with the rising edge of shift clock CLK. The driver output amplitude is VDD2-VEE. O0, O264 Driver Output The signal of V EE level is outputted by fixation. R,/LR, R,/LL Shift direction control Input The shift direction control pin of shift register. R,/LR, R,/LL = H (right shift): STVR → O 1 → O263 → STVL R,/LR, R,/LL = L (left shift): STVL → O263 → O1 → STVR R,/LR and R,/LL are connected inside IC. STVR, STVL Start pulse I/O This is the I/O of the internal shift r egister. The start pulse is read at the rising edge of shift clock CLK (CLKR, CLKL), and scan signals are output from the driver output pins. The input level is a VDD1-VSS (logic level). When in MODE = H, the start pulse is output at the falling edge of the 263rd clock of shift clock CLK, and is cleared at the falling edge of the 264th clock. The output level is V DD1-VSS (logic level). CLKR, CLKL Shift clock Input This pin inputs a shift clock to the in ternal shift register. The shift operation is performed in synchronization with the rising edge of this input. CLKR and CLKL are connected inside IC. OER, OEL Output enable Input When this pin goes hi gh level, the driver output is fixed to VEE level. The shift register is not cleared. CLK is asynchronous in the clock. OER and OEL are connected inside IC. /AOR, /AOL All-on control Input When this pin goes low level, all driver output = V DD2 level. The shift register is not cleared. This pin has priority over OER and OEL. This pin is pulled up to VDD1 power supply inside IC. CLK is asynchronous in the clock. /AOR and /AOL are connected inside IC. MODE Selection of number of outputs Input MODE = V DD1 or open: 263 outputs MODE = VSS: 256 outputs (Driver pins O129 to O135 are invalid.) Input level is VDD1-VSS (logic level) This pin is pulled up to VDD1 power supply inside IC. VDD1 Logic power supply – 2.3 to 3.6 V VDD2 Driver positive power supply – 5 to 30 V. The driver output: High level VSS Logic ground – Connect this pin to the ground of the system. VEE Negative Power supply for internal operation – −15 to −3 V. The driver output: Low level Cautions 1. To prevent latch-up, turn on power to V DD1→ VEE→ VDD2→ logic input in this order. Turn off power in the reverse order. These power up/down sequence must be observed also during transition period. 2. Insert a capacitor of about 0.1 µF between each power line, as shown below, to secure noise margin such as V IH and VIL. VDD2 VDD1 VSS 0.1 Fµ 0.1 Fµ 0.1 Fµ VEE

Data Sheet S16563EJ1V0DS 5 µ PD16707A 4. RELATIONS OF ENABLE OUTPUT PIN NUMBER SELECTION AND OUTPUT PIN Switching is possible for 263/256 with µPD16707A by the MODE pin. MODE = H or open MODE = L 263-output Mode 256-output Mode O1 O 1 O2 O 2 O3 O 3 O4 O 4 O5 O 5 O6 O 6 ↓ ↓ O127 O 127 O128 O 128 O129 V OUT = VEE O130 V OUT = VEE O131 V OUT = VEE O132 V OUT = VEE O133 V OUT = VEE O134 V OUT = VEE O135 V OUT = VEE O136 O 136 O137 O 137 ↓ ↓ O259 O 259 O260 O 260 O261 O 261 O262 O 262 O263 O 263

Data Sheet S16563EJ1V0DS 6 µ PD16707A 5. TIMING CHART (R,/LR = R,/LL = H, MODE = H, /AOR = /AOL = H) CLKR 1 OER O 1 (O263) O 2 (O262) STVL (STVR) O 1 of next stage (O263 of next stage) O2 of next stage (O262 of next stage) 2 3 262 263 264 265 STVR (STVL) O 3 (O261) O262 (O2) O263 (O1) 266 CLKL OEL Remark The signal name in parenthesis is it at the time of R,/LR = R,/LL = L.

Data Sheet S16563EJ1V0DS 7 µ PD16707A 6. ELECTRICAL SPECIFICATIONS Absolute Maximum Ratings (TA = 25°C, VSS = 0 V) Parameter Symbol Rating Unit Logic Supply Voltage V DD1 −0.5 to +7.0 V Driver Positive Supply Voltage V DD2 −0.5 to +32 V Power Supply Voltage V DD2-VEE −0.5 to +42 V Internal Operation Negative Supply Voltage V EE –16 to + 0.5 V Input Voltage V I −0.5 to VDD1 + 0.5 V Operating Ambient Temperature T A −20 to +75 °C Storage Temperature T stg −55 to +125 °C Caution Product qualify may suffer if the absolute m aximum rating is exceeded ev en momentarily for any parameter. That is, the absolute maximum ratings are rated values at which the product is on the verge of suffering physical damage, and therefore the product must be used under conditions that ensure that the absolute maximum ratings are not exceeded. Recommended Operating Range (TA = –20 to +75°C, VSS = 0 V) Parameter Symbol Condition MIN. TYP. MAX. Unit Logic Supply Voltage V DD1 2.3 3.3 3.6 V Driver Positive Supply Voltage V DD2 5 20 30 V Internal Operation Negative Supply Voltage V EE −15 −5 −3 V Power Supply Voltage V DD2-VEE 8 25 40 V Clock Frequency f CLK 500 kHz

Data Sheet S16563EJ1V0DS 8 µ PD16707A Parameter Symbol Condition MIN. TYP.Note MAX. Unit High level Input Voltage V IH 0.8 V DD1 V DD1 V Low level Input Voltage V IL CLKR, CLKL, STVR, STVL, R,/LR, R,/LL, OER, OEL, MODE VSS 0.2 V DD1 V High level Output Voltage V OH STVR (STVL), IOH = −40 µA V DD1 − 0.4 V DD1 V Low level Output Voltage V OL STVR (STVL), IOL = +40 µA VSS V SS + 0.4 V LCD Driver Output ON Resistance R ON V OUT = VEE + 1.0 V or VDD2 – 1.0 V 0.4 1.0 kΩ Pull-up Resistance R PU V DD1 = 3.0 V (/AOR, /AOL, MODE) 10 50 100 kΩ Input Leak Current I IL V I = 0 V or 3.6 V (except for /AOR, /AOL, MODE) ±1.0 µA Static Current Dissipation I DD1 V DD1, fCLK = 50 kHz, OER = OEL = L, f STV = 60 Hz, no load 20 200 µA I DD2 V DD2, fCLK = 50 kHz, OER = OEL = L, f STV = 60 Hz, no load 10 100 µA I EE V EE, fCLK = 50 kHz, OER = OEL = L, f STV = 60 Hz, no load –300 –30 µA Remark STV: STVR (STVL) Note The TYP. value are reference values at VDD1 = 3.0 V, TA = 25°C. ★

Data Sheet S16563EJ1V0DS 9 µ PD16707A Switching Characteristics (TA = –20 to +75°C, VDD1 = 2.3 to 3.6 V, VDD2 = 20 V, VEE = –5 V, VSS = 0 V) Parameter Symbol Condition MIN. TYP. MAX. Unit Cascade Output Delay Time t PHL1 CL = 20 pF, 500 ns t PLH1 CLKR (CLKL) → STVL (STVR) 500 ns tPHL2 500 ns tPLH2 CL = 300 pF, CLKR (CLKL) → On 500 ns tPHL3 500 ns Driver Output Delay Time tPLH3 CL = 300 pF, OER (OEL) → On 500 ns Output Rise Time t TLH CL = 300 pF 800 ns Output Fall Time t THL 800 ns Input Capacitance C I TA = 25°C 15 pF Timing Requirements (TA = −20 to +75°C, VDD1 = 2.3 to 3.6 V, VDD2 = 20 V, VEE = −5 V, VSS = 0 V) Parameter Symbol Condition MIN. TYP. MAX. Unit Clock Pulse High Width PW CLK(H) 500 ns Clock Pulse Low Width PW CLK(L) 500 ns Enable Pulse Width PW OE 1000 ns Data Setup Time t SETUP STVR (STVL) ↑→ CLKR, CLKL↑ 200 ns Data Hold Time t HOLD CLKR, CLKL ↑→ STVR (STVL) ↓ 200 ns Remark Unless otherwise specified, the input level is defined to be VIH = 0.8 VDD1, VIL = 0.2 VDD1. Caution Keep the time and fall time of the logic input to tr = tf = 20 ns (10 to 90% of the rated values).

Data Sheet S16563EJ1V0DS 10 µ PD16707A Switching Characteristics Waveform (R,/LR = R,/LL = H, MODE = H) Unless otherwise specified, the input level is defined to be VIH = 0.8 VDD1, VIL = 0.2 VDD1. tSETUP CLKR STVR tr 90% 10% tHOLD PW CLK(H) tf 260 261 tPLH2 O tPHL2 O O 262 O 263 tPLH1 STVL tPHL1 OER tPHL3 O 1 to O 263 tPLH3 262 263

  •   90%10%tTLH tTHL PW OE PW CLK(L) 50% 50% 10% 90% 50% 90% 10% 50% 50% CLKL OEL

Data Sheet S16563EJ1V0DS 11 µ PD16707A 7. RECOMMENDED MOUNTING CONDITIONS The following conditions must be met of mounting conditions of the µ PD16707A. For more details, refer to the [Semiconductor Device Mounting Manual] (http://www.necel.com/pkg/en/mount/index.html) Please consult with our sales offices in case other m ounting process is used, or in case the mounting is done under different conditions. µ PD16707AN-xxx: TCP (TAB Package) Mounting Condition Mounting Method Condition Thermocompression Soldering Heating tool 300 to 350°C, heating for 2 to 3 seconds : pressure 100g (per solder) ACF (Adhesive Conductive Film) Temporary bonding 70 to 100°C: pressure 3 to 8 kg/cm : time 3 to 5 sec. Real bonding 165 to 180°C: pressure 25 to 45 kg/cm : time 30 to 40 sec. (When using the anisotropy conductive film SUMIZAC1003 of Sumitomo Bakelite,Ltd). Caution To find out the detailed conditions for mounting the ACF part, please contact the ACF manufacturing company. Be sure to avoid using two or more mounting methods at a time.

Data Sheet S16563EJ1V0DS 12 µ PD16707A NOTES FOR CMOS DEVICES

1 PRECAUTION AGAINST ESD FOR SEMICONDUCTORS

Note: Strong electric field, when exposed to a MOS device, can cause destruction of the gate oxide and ultimately degrade the device operation. Steps must be taken to stop generation of static electricity as much as possible, and quickly dissipate it once, when it has occurred. Environmental control must be adequate. When it is dry, humidifier should be used. It is recommended to avoid using insulators that easily build static electricity. Semiconductor devices must be stored and transported in an anti-static container, static shielding bag or conductive material. All test and measurement tools including work bench and floor should be grounded. The operator should be grounded using wrist strap. Semiconductor devices must not be touched with bare hands. Similar precautions need to be taken for PW boards with semiconductor devices on it.

2 HANDLING OF UNUSED INPUT PINS FOR CMOS

Note: No connection for CMOS device inputs can be cause of malfunction. If no connection is provided to the input pins, it is possible that an internal input level may be generated due to noise, etc., hence causing malfunction. CMOS devices behave differently than Bipolar or NMOS devices. Input levels of CMOS devices must be fixed high or low by using a pull-up or pull-down circuitry. Each unused pin should be connected to V DD or GND with a resistor, if it is considered to have a possibility of being an output pin. All handling related to the unused pins must be judged device by device and related specifications governing the devices.

3 STATUS BEFORE INITIALIZATION OF MOS DEVICES

Note: Power-on does not necessarily define initial status of MOS device. Production process of MOS does not define the initial operation status of the device. Immediately after the power source is turned ON, the devices with reset function have not yet been initialized. Hence, power-on does not guarantee out-pin levels, I/O settings or contents of registers. Device is not initialized until the reset signal is received. Reset operation must be executed immediately after power-on for devices having reset function.

µ PD16707A Reference Documents NEC Semiconductor Device Reliability/Quality Control System (C10983E) Quality Grades On NEC Semiconductor Devices (C11531E) The information in this document is current as of January 2004. The information is subject to change without notice. For actual design-in, refer to the latest publications of NEC Electronics data sheets or data books, etc., for the most up-to-date specifications of NEC Electronics products. Not all products and/or types are available in every country. Please check with an NEC Electronics sales representative for availability and additional information. No part of this document may be copied or reproduced in any form or by any means without the prior written consent of NEC Electronics. NEC Electronics assumes no responsibility for any errors that may appear in this document. NEC Ele ctronics does not assume any liability for infringement of patents, copyrights or other intellectual property rights of third parties by or arising from the use of NEC Electronics products listed in this document or any other liability arising from the use of such products. No license, express, implied or otherwise, is granted under any patents, copyrights or other intellectual property rights of NEC Electronics or others. Descriptions of circuits, software and other related information in this document are provided for illustrative purposes in semiconductor product operation and application examples. The incorporation of these circuits, software and information in the design of a customer's equipment shall be done under the full responsibility of the customer. NEC Electronics assumes no responsibility for any losses incurred by customers or third parties arising from the use of these circuits, software and information. While NEC Electronics endeavors to enhance the quality, reliability and safety of NEC Electronics products, customers agree and acknowledge that the possibility of defects thereof cannot be eliminated entirely. To minimize risks of damage to property or injury (including death) to persons arising from defects in NEC Electronics products, customers must incorporate sufficient safety measures in their design, such as redundancy, fire-containment and anti-failure features. NEC Electronics products are classified into the following three quality grades: "Standard", "Special" and "Specific". The "Specific" quality grade applies only to NEC Electronics products developed based on a customer- designated "quality assurance program" for a specific application. The recommended applications of an NEC Electronics product depend on its quality grade, as indicated below. Customers must check the quality grade of each NEC Electronics product before using it in a particular application. "Standard":Computers, office equipment, communications equipment, test and measurement equipment, audio and visual equipment, home electronic appliances, machine tools, personal electronic equipment and industrial robots. "Special": Transportation equipment (automobiles, trains, ships, etc.), traffic control systems, anti-disaster systems, anti-crime systems, safety equipment and medical equipment (not specifically designed for life support). "Specific":Aircraft, aerospace equipment, submersible repeaters, nuclear reactor control systems, life support systems and medical equipment for life support, etc. The quality grade of NEC Electronics products is "Standard" unless otherwise expressly specified in NEC Electronics data sheets or data books, etc. If customers wish to use NEC Electronics products in applications not intended by NEC Electronics, they must contact an NEC Electronics sales representative in advance to determine NEC Electronics' willingness to support a given application. (Note) (1) "NEC Electronics" as used in this statement means NEC Electronics Corporation and also includes its majority-owned subsidiaries. (2) "NEC Electronics products" means any product developed or manufactured by or forNEC Electronics (as defined above). M8E 02. 11-1