PCZ1H220MCL1GS

PCZ NICHICON | Alldatasheet

Document overview

• Manufacturer or author: Provided By alldatasheet.com(free datasheet download site)
• PDF pages: 2

Technical content

CONDUCTIVE POLYMER ALUMINUM SOLID ELECTROLYTIC CAPACITORS PCZ Chip Type, Higher Capacitance High Temperature Range Specifications Temperature Characteristics (Max.Impedance Ratio) Category Temperature Range Rated Voltage Range Rated Capacitance Range Capacitance Tolerance Tangent of loss angle (tan δ) ESR ( 1) Leakage Current ( 2) Performance CharacteristicsItem –55 to +150°C 16 to 63V 12 to 1000µF ± 20% at 120Hz, 20°C Less than or equal to the specified value at 120Hz, 20°C Less than or equal to the specified value at 100kHz, 20°C After 2 minutes' application of rated voltage, leakage current is not more than 0.03CV. Endurance ESR after Endurance ( 1) Damp Heat (Steady State) Resistance to Soldering Heat Marking The specifications listed at right shall be met when the capacitors are restored to 20°C after the rated voltage is applied for 2000 hours at 150°C. Less than or equal to the specified value at 100kHz, -40°C The specifications listed at right shall be met when the capacitors are restored to 20°C after the rated voltage is applied for 2000 hours at 85°C , 85% RH. After soldering the capacitor under the soldering conditions prescribed here, the capacitor shall meet the specifications listed at right. Pre-heating shall be done at 150 to 200°C and for 60 to 180 sec. The duration for over +230°C temperature at capacitor surface shall not exceed 60 seconds. In case peak temperature is 260°C or less, reflow soldering shall be two times maximum. Measurement for solder temperature profile shall be made at the capacitor top. Navy blue print on the case top Capacitance change tan δ Leakage current ( 2) ESR ( 1) Within ± 20% of initial capacitance value ( 3) 150% or less of the initial specified value 200% or less of the initial specified value Less than or equal to the initial specified value Capacitance change tan δ Leakage current ( 2) ESR ( 1) Within ± 20% of initial capacitance value ( 3) 150% or less of the initial specified value 200% or less of the initial specified value Less than or equal to the initial specified value Capacitance change tan δ Leakage current ( 2) ESR ( 1) Within ± 10% of the initial capacitance value ( 3) 130% or less than the initial specified value 130% or less than the initial specified value Less than or equal to the initial specified value High reliability. Low ESR, High ripple current. Long life of 2000 hours at 150°C. SMD type : Lead free reflow soldering condition at 260°C peak complete correspondence. Compliant to the RoHS directive (2011/65/EU,(EU)2015/863). ESR after Endurance at -40°C. AEC-Q200 Qualified. Please contact us for details.

1 ESR should be measured at both of the terminal ends closest where the terminals

protrude through the plastic platform.

2 Conditioning : If any doubt arises, measure the leakage current after the voltage treatment of

applying DC rated voltage continuously to the capacitor for 120 minutes at 105°C. 3 Initial value : The value before test of examination of resistance to soldering. Positive C Z 2 2 0 V 0 1 2 H 0.3 max. φD±0.5 B±0.2 A±0.2 C±0.2 0.5 max. E Series Voltage (V:35V) Plastic platform Lot No.Capacitance NegativeL±0.5 Standard C Z 2 2 0 V 0 1 2 Negative PositiveVibration Resistance H 0.3 max. φD±0.5 B±0.2 A±0.2 C±0.2 0.5 max.E L±0.5 Plastic platform Aid electrode Series Voltage (V:35V) Lot No.Capacitance Dimensions PCZ High Temperature PCH Dimension table in next page. P C Z V M C L 1 1 G S Configuration Taping code Size code Capacitance tolerance (±20%) Rated capacitance (220µF) Rated voltage (35V) Series name Type Standard Vibration Resistance CodeSize L ※Please ask for Part Number. Type numbering system (Example : 35V 220µF) The vibration structure-resistant product is also available upon request, please ask for details. ( ) : Size of the vibration structure-resistant product. (mm) Vibration Resistance φ×- UP 4J[F φ×- UP φ×- UP Size φD L A B C E H (mm) Standard φ8 × 7L 8.0 6.9 9.0 8.3 8.3 3.2 0.8 to 1.1 φ8 × 10L 8.0 9.9 9.0 8.3 8.3 3.2 0.8 to 1.1 φ8 × 12L 8.0 11.9 9.0 8.3 8.3 3.2 0.8 to 1.1 φ10 × 10L 10.0 9.9 11.0 10.3 10.3 4.6 0.8 to 1.1 φ10 × 8L 10.0 7.9 11.0 10.3 10.3 4.6 0.8 to 1.1 φ10 × 12.7L 10.0 12.6 11.0 10.3 10.3 4.6 0.8 to 1.1 Voltage V 16 20 25 35 50 63 Code C D E V H J Frequency coefficient of rated ripple current Frequency Coefficient ※ I : Leakage Current(µA), C : Rated Capacitance(µF), V : Rated Voltage(V) 120Hz 1kHz 10kHz 100kHz or more 0.05 0.30 0.70 1.00 CAT.8100N

CONDUCTIVE POLYMER ALUMINUM SOLID ELECTROLYTIC CAPACITORS PCZ Rated Voltage （V） （code） Surge Voltage (V) Rated Capacitance （µF） Case Size φD×L （mm）tan δ Leakage Current （µA） Initial ESR (mΩ) （20℃/100kHz) Low temp. ESR after Endurance (mΩ) （−40℃ /100kHz） Rated Ripple （mArms） （150℃ /100kHz） Part Number at 20℃ after 2 minutes ） （1C） 20 220 8×7 0.08 105 30 60 800 PCZ1C221MCL1GS 470 ▲ 8×10 0.08 225 17 34 1900 PCZ1C471MCL6GS 470 10×8 0.08 225 32 64 1400 PCZ1C471MCL1GS 560 △ 8×12 0.08 268 16 32 2000 PCZ1C561MCL2GS 680 10×10 0.08 326 19 38 1900 PCZ1C681MCL1GS 1000 10×12.7 0.08 480 13 26 2200 PCZ1C102MCL1GS （1D） 25 100 8×7 0.08 60 39 78 600 PCZ1D101MCL1GS 220 ▲ 8×10 0.08 132 20 40 1800 PCZ1D221MCL6GS 220 10×8 0.08 132 33 66 1400 PCZ1D221MCL1GS 270 △ 8×12 0.08 162 18 36 1900 PCZ1D271MCL2GS 330 10×10 0.08 198 20 40 1800 PCZ1D331MCL1GS 470 10×12.7 0.08 282 15 30 2100 PCZ1D471MCL1GS （1E） 31 68 8×7 0.08 51 41 82 600 PCZ1E680MCL1GS 150 ▲ 8×10 0.08 112 20 40 1800 PCZ1E151MCL6GS 150 10×8 0.08 112 33 66 1400 PCZ1E151MCL1GS 180 △ 8×12 0.08 135 19 38 1900 PCZ1E181MCL2GS 270 10×10 0.08 202 20 40 1800 PCZ1E271MCL1GS 330 10×12.7 0.08 247 15 30 2100 PCZ1E331MCL1GS （1V） 43 47 8×7 0.08 49 44 88 600 PCZ1V470MCL1GS 100 ▲ 8×10 0.08 105 22 44 1700 PCZ1V101MCL6GS 100 10×8 0.08 105 33 66 1400 PCZ1V101MCL1GS 150 △ 8×12 0.08 157 21 42 1800 PCZ1V151MCL2GS 180 10×10 0.08 189 20 40 1800 PCZ1V181MCL1GS 220 10×12.7 0.08 231 16 32 2000 PCZ1V221MCL1GS （1H） 63 22 8×7 0.08 33 48 96 600 PCZ1H220MCL1GS 47 ▲ 8×10 0.08 70 28 56 1500 PCZ1H470MCL6GS 47 10×8 0.08 70 35 70 1300 PCZ1H470MCL1GS 56 △ 8×12 0.08 84 27 54 1500 PCZ1H560MCL2GS 68 10×10 0.08 102 28 56 1500 PCZ1H680MCL1GS 100 10×12.7 0.08 150 24 48 1600 PCZ1H101MCL1GS （1J） 79 12 8×7 0.08 22 52 104 400 PCZ1J120MCL1GS 27 ▲ 8×10 0.08 51 38 76 1300 PCZ1J270MCL6GS 27 10×8 0.08 51 37 74 1300 PCZ1J270MCL1GS 39 △ 8×12 0.08 73 35 70 1300 PCZ1J390MCL2GS 47 10×10 0.08 88 33 66 1400 PCZ1J470MCL1GS 68 10×12.7 0.08 128 28 56 1500 PCZ1J680MCL1GS Dimensions No marked, 1 will be put at 12th digit of type numbering system. : In this case, 6 will be put at 12th digit of type numbering system. : In this case, 2 will be put at 12th digit of type numbering system. For taping specifications, recommended land size/soldering by reflow and minimum order quantity, please refer to the Guidelines for Aluminum Electrolytic Capacitors. CAT.8100N