PCW NICHICON | Alldatasheet
Document overview
- Manufacturer or author: Provided By alldatasheet.com(free datasheet download site)
- PDF pages: 2
Technical content
Chip Type, 125°C Reliability Ripple Load Life of 2000h at 125°C. High reliability, Low ESR, High ripple current. SMD type : Lead free reflow soldering condition at 260°C peak complete correspondence. Compliant to the RoHS directive (2011/65/EU,(EU)2015/863). AEC-Q200 Qualified. Please contact us for details. Dimension table in next page. Specifications Temperature Characteristics (Max.Impedance Ratio) Category Temperature Range Rated Voltage Range Rated Capacitance Range Capacitance Tolerance Tangent of loss angle (tan δ) ESR ( 1) Leakage Current ( 2) Performance CharacteristicsItem –55 to +125°C 2.5 to 6.3V 150 to 1800µF ± 20% at 120Hz, 20°C Less than or equal to the specified value at 120Hz, 20°C Less than or equal to the specified value at 100kHz, 20°C Less than or equal to the specified value . After 2 minutes' application of rated voltage at 20°C Endurance Damp Heat (Steady State) Resistance to Soldering Heat Marking The specifications listed at right shall be met when the capacitors are restored to 20°C after D.C. bias plus rated ripple current is applied for 2000 hours at 125°C, the peak voltage shall not exceed the rated voltage. The specifications listed at right shall be met when the capacitors are restored to 20°C after the rated voltage is applied for 1000 hours at 85°C, 85% RH. After soldering the capacitor under the soldering conditions prescribed here, the capacitor shall meet the specifications listed at right. Pre-heating shall be done at 150 to 200°C and for 60 to 180 sec. The duration for over +230°C temperature at capacitor surface shall not exceed 60 seconds. In case peak temperature is 250°C or less, reflow soldering shall be two times maximum. In case peak temperature is 260°C or less, reflow soldering shall be once. The temperature profile measurement shall be the temperature at the top of the capacitor. Navy blue print on the case top Capacitance change tan δ Leakage current ( 2) ESR ( 1) Within ± 20% of the initial capacitance value ( 3) 150% or less than the initial specified value 150% or less than the initial specified value Less than or equal to the initial specified value Capacitance change tan δ Leakage current ( 2) ESR ( 1) Within ± 20% of the initial capacitance value ( 3) 150% or less than the initial specified value 150% or less than the initial specified value Less than or equal to the initial specified value Capacitance change tan δ Leakage current ( 2) ESR ( 1) Within ± 10% of the initial capacitance value ( 3) 130% or less than the initial specified value 130% or less than the initial specified value Less than or equal to the initial specified value 1 ESR should be measured at both of the terminal ends closest where the terminals protrude through the plastic platform. 2 Conditioning : If any doubt arises, measure the leakage current after the voltage treatment of applying DC rated voltage continuously to the capacitor for 120 minutes at 105°C. 3 Initial value : The value before test of examination of resistance to soldering. P C W E M C O 1 1 G S Configuration Taping code Size code Capacitance tolerance (±20%) Rated capacitance (270µF) Rated voltage (2.5V) Type, Series name C W 2 7 0 e 3 1 1 H 0.3 max.B± 0.2 A±0.2 C±0.2 0.5 max. φD±0.5 E Series Voltage (e:2.5v) Plastic platform Lot No. Capacitance Negative Positive φ6.3, φ 8：L±0.5 φ5：L±0.3 Dimensions Type numbering system (Example : 2.5V 270µF) Frequency coefficient of rated ripple current
0 Frequency0/
120Hz 1kHz 10kHz 100kHz or more 0.05 0.30 0.70 1.00 Voltage V 2.5 4 6.3 Code e g j Size φD L A B C E H φ5 × 6L 5.0 5.9 6.0 5.3 5.3 1.6 0.5 to 0.8 PCW PCJ High temperature, Ripple current superimposition CONDUCTIVE POLYMER ALUMINUM SOLID ELECTROLYTIC CAPACITORS φ6.3 × 6L 6.3 6.0 7.3 6.6 6.6 2.1 0.5 to 0.8 × 7L 8.0 7.0 9.0 8.3 8.3 3.2 0.8 to 1.1 × 10L 8.0 10.0 9.0 8.3 8.3 3.2 0.8 to 1.1 (mm) CAT.8100N
CONDUCTIVE POLYMER ALUMINUM SOLID ELECTROLYTIC CAPACITORS For taping specifications, recommended land size/soldering by reflow and minimum order quantity, please refer to the Guidelines for Aluminum Electrolytic Capacitors. Rated Voltage （V） （code） Surge Voltage (V) Rated Capacitance （µF） Case Size φD×L （mm） tanδ Leakage Current （µA） ESR （mΩ） （20℃ /100kHz） Rated Ripple （mArms） （125℃ /100kHz） Part Number at 20℃ after 2 minutes ） 2.5 （0E） 2.8 270 5×6 0.08 270 16 1800 PCW0E271MCO1GS 390 6.3×6 0.08 292 15 1890 PCW0E391MCO1GS 820 8×7 0.08 615 14 2100 PCW0E821MCO1GS 1800 8×10 0.08 1350 13 2200 PCW0E182MCO1GS （0G） 4.6 180 5×6 0.08 288 17 1720 PCW0G181MCO1GS 330 6.3×6 0.08 396 16 1800 PCW0G331MCO1GS 560 8×7 0.08 672 15 2150 PCW0G561MCO1GS 1200 8×10 0.08 1440 14 2300 PCW0G122MCO1GS 6.3 （0J） 7.2 150 5×6 0.08 378 18 1580 PCW0J151MCO1GS 220 6.3×6 0.08 415 16 1800 PCW0J221MCO1GS 470 8×7 0.08 888 15 2200 PCW0J471MCO1GS 1000 8×10 0.08 1890 14 2500 PCW0J102MCO1GS Blue : New product （as of October 2024） CAT.8100N