PCS NICHICON | Alldatasheet

Document overview

  • Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
  • PDF pages: 2

Technical content

CAT.8100H CONDUCTIVE POLYMER ALUMINUM SOLID ELECTROLYTIC CAPACITORS PCS Chip Type, LongLife Assurance Specifications Temperature Characteristics (Max.Impedance Ratio) Category Temperature Range Rated Voltage Range Rated Capacitance Range Capacitance Tolerance Tangent of loss angle (tan δ) ESR ( 1) Leakage Current ( 2) Performance CharacteristicsItem –55 to +105°C 4 to 16V 22 to 560µF ± 20% at 120Hz, 20°C Less than or equal to the specified value at 120Hz, 20°C Less than or equal to the specified value at 100kHz, 20°C Less than or equal to the specified value . After 2 minutes' application of rated voltage at 20°C Endurance Damp Heat (Steady State) Resistance to Soldering Heat Marking The specifications listed at right shall be met when the capacitors are restored to 20°C after the rated voltage is applied for 5000 hours at 105°C. The specifications listed at right shall be met when the capacitors are restored to 20°C after the rated voltage is applied for 1000 hours at 60°C, 90% RH. After soldering the capacitor under the soldering conditions prescribed here, the capacitor shall meet the specifications listed at right. Pre-heating shall be done at 150 to 200°C and for 60 to 180 sec. The duration for over +230°C temperature at capacitor surface shall not exceed 60 seconds. In case peak temperature is 250°C or less, reflow soldering shall be two times maximum. In case peak temperature is 260°C or less, reflow soldering shall be once. Measurement for solder temperature profile shall be made at the capacitor top and the terminal. Navy blue print on the case top Capacitance change tan δ Leakage current ( 2) ESR ( 1) Within ± 20% of the initial capacitance value ( 3) 150% or less than the initial specified value 150% or less than the initial specified value Less than or equal to the initial specified value Capacitance change tan δ Leakage current ( 2) ESR ( 1) Within ± 20% of the initial capacitance value ( 3) 150% or less than the initial specified value 150% or less than the initial specified value Less than or equal to the initial specified value Capacitance change tan δ Leakage current ( 2) ESR ( 1) Within ± 10% of the initial capacitance value ( 3) 130% or less than the initial specified value 130% or less than the initial specified value Less than or equal to the initial specified value Load life of 5000 hours at 105°C. SMD type : Lead free reflow soldering condition at 260°C peak correspondence. Compliant to the RoHS directive (2011/65/EU). AEC-Q200 compliant. Please contact us for details. 1 ESR should be measured at both of the terminal ends closest where the terminals protrude through the plastic platform. 2 Conditioning : If any doubt arises, measure the leakage current after the voltage treatment of applying DC rated voltage continuously to the capacitor for 120 minutes at 105°C. 3 Initial value : The value before test of examination of resistance to soldering. P C S J M C L G S Configuration Taping code Size code Capacitance tolerance (±20%) Rated capacitance (220µF) Rated voltage (6.3V) Series name Type C S 2 2 0 j 9 4 1 H 0.3 MAX. φD±0.5 B±0.2 A±0.2 C±0.2 0.5 MAX. E LSeries Voltage ( j:6.3v) Plastic platform Lot No.Capacitance Negative Positive +0.1 -0.4 Dimensions Type numbering system (Example : 6.3V 220µF) Voltage V 4 6.3 10 16 Code g j A C Size φD L A B C E H φ5 × 6L 5.0 5.9 6.0 5.3 5.3 1.6 0.5 to 0.8 φ6.3 × 6L 6.3 5.9 7.3 6.6 6.6 2.1 0.5 to 0.8 φ8 × 7L 8.0 6.9 9.0 8.3 8.3 3.2 0.8 to 1.1 (mm) Dimension table in next page. PCS Long Life PCF Frequency coefficient of rated ripple current

0 Frequency0/

120Hz 1kHz 10kHz 100kHz or more 0.05 0.30 0.70 1.00

CAT.8100H CONDUCTIVE POLYMER ALUMINUM SOLID ELECTROLYTIC CAPACITORS PCS Dimensions Taping specifications are given in page 23. Recommended land size, soldering by reflow are given in page 18, 19. Please refer to page 3 for the minimum order quantity. Rated ripple current (mArms) at 105°C 100kHz Rated Capacitance (µF) Rated Voltage (V)(code) Surge Voltage (V) Leakage Current (µA) ESR (mΩ) (at 100kHz 20°C) Rated Ripple (mArms)tan δ Part NumberCase Size φD × L (mm) (0G) (1C) (1A) 6.3 (0J) 4.6 18.4 11.5 7.2 150 330 330 560 100 100 120 220 220 390 120 150 270 120 120 264 264 448 100 126 126 151 277 277 491 100 112 136 240 300 540 100 125 125 218 262 384 2200 2800 3200 3600 1600 2400 2800 2800 2800 3200 3200 1300 2300 2100 2300 2600 3200 1100 2000 2200 2200 2800 2800 PCS0G151MCL1GS PCS0G331MCL1GS PCS0G331MCL9GS PCS0G561MCL1GS PCS0J470MCL1GS PCS0J101MCL1GS PCS0J101MCL9GS PCS0J121MCL9GS PCS0J221MCL1GS PCS0J221MCL9GS PCS0J391MCL1GS PCS1A330MCL1GS PCS1A560MCL9GS PCS1A680MCL1GS PCS1A121MCL1GS PCS1A151MCL9GS PCS1A271MCL1GS PCS1C220MCL1GS PCS1C390MCL1GS PCS1C390MCL9GS PCS1C680MCL1GS PCS1C820MCL9GS PCS1C121MCL1GS 0.12 0.12 0.12 0.12 0.12 0.12 0.12 0.12 0.12 0.12 0.12 0.12 0.12 0.12 0.12 0.12 0.12 0.12 0.12 0.12 0.12 0.12 0.12 5 × 6 6.3 × 6 8 × 7 8 × 7 5 × 6 5 × 6 6.3 × 6 6.3 × 6 6.3 × 6 8 × 7 8 × 7 5 × 6 6.3 × 6 5 × 6 6.3 × 6 8 × 7 8 × 7 5 × 6 5 × 6 6.3 × 6 6.3 × 6 8 × 7 8 × 7 No marked, 1 will be put at 12th digit of type numbering system. : In this case, 9 will be put at 12th digit of type numbering system.