PCM

PCM NICHICON | Alldatasheet

Document overview

• Manufacturer or author: Provided By alldatasheet.com(free datasheet download site)
• PDF pages: 2

Technical content

High reliability , Low ESR, High ripple current. Long life of 8000 hours at 125°C. SMD type : Lead free reflow soldering condition at 260°C peak complete correspondence. Compliant to the RoHS directive (2011/65/EU,(EU)2015/863). ESR after Endurance at -40°C. AEC-Q200 Qualified. Please contact us for details. CONDUCTIVE POLYMER ALUMINUM SOLID ELECTROLYTIC CAPACITORS PCM Chip Type, Higher Capacitance High Temperature Range Performance Characteristics –55 to +125°CCategory Temperature Range Item Specifications Temperature Characteristics (Max.Impedance Ratio) Rated Voltage Range Rated Capacitance Range Capacitance Tolerance Tangent of loss angle (tan δ) ESR ( 1) Leakage Current ( 2) 16 to 80V 12 to 1000µF ± 20% at 120Hz, 20°C Less than or equal to the specified value at 120Hz, 20°C Less than or equal to the specified value at 100kHz, 20°C After 2 minutes' application of rated voltage, leakage current is not more than 0.03CV. Damp Heat (Steady State) Resistance to Soldering Heat Marking The specifications listed at right shall be met when the capacitors are restored to 20°C after the rated voltage is applied for 8000 hours (φD = 6.3:6000hours) at 125°C. The specifications listed at right shall be met when the capacitors are restored to 20°C after the rated voltage is applied for 2000 hours at 85°C, 85% RH. After soldering the capacitor under the soldering conditions prescribed here, the capacitor shall meet the specifications listed at right. Pre-heating shall be done at 150 to 200°C and for 60 to 180 sec. The duration for over +230°C temperature at capacitor surface shall not exceed 60 seconds. In case peak temperature is 260°C or less, reflow soldering shall be two times maximum. Measurement for solder temperature profile shall be made at the capacitor top. Navy blue print on the case top Capacitance change tan δ Leakage current ( 2) ESR ( 1) Within ± 20% of initial capacitance value ( 3) 150% or less of the initial specified value 200% or less of the initial specified value Less than or equal to the initial specified value Capacitance change tan δ Leakage current ( 2) ESR ( 1) Within ± 20% of initial capacitance value ( 3) 150% or less of the initial specified value 200% or less of the initial specified value Less than or equal to the initial specified value Capacitance change tan δ Leakage current ( 2) ESR ( 1) Within ± 10% of the initial capacitance value ( 3) 130% or less than the initial specified value 130% or less than the initial specified value Less than or equal to the initial specified value Endurance

1 ESR should be measured at both of the terminal ends closest where the terminals

protrude through the plastic platform.

2 Conditioning : If any doubt arises, measure the leakage current after the voltage treatment of

applying DC rated voltage continuously to the capacitor for 120 minutes at 105°C. 3 Initial value : The value before test of examination of resistance to soldering. C M 1 5 0 V 3 3 1 φ6.3:L±0.3 φ8,10:L±0.5 H 0.3 max. φD±0.5 B±0.2 A±0.2 C±0.2 0.5 max. E Series Voltage (V:35V) Plastic platform Lot No.Capacitance Negative Positive Negative PositiveVibration Resistance H 0.3 max. φD±0.5 B±0.2 A±0.2 C±0.2 0.5 max.E L±0.5 Plastic platform Aid electrode Series Voltage (V:35V) Lot No.Capacitance C M 1 5 0 V 3 3 1 Standard Dimensions P C M V M C L 1 1 G S Configuration Taping code Size code Capacitance tolerance (±20%) Rated capacitance (150µF) Rated voltage (35V) Series name Type Standard Vibration Resistance CodeSize L ※Please ask for Part Number. Type numbering system (Example : 35V 150µF) The vibration structure-resistant product is also available upon request, please ask for details. ( ) : Size of the vibration structure-resistant product. Dimension table in next page. Less than or equal to the specified value at 100kHz, -40°CESR after Endurance ( 1) After storing the capacitors under no load at 125°C for 1000 hours and then performing voltage treatment based on JIS C 5101-4 clause 4.1 at 20°C, they shall meet the specified values for the endurance characteristics listed above.Shelf Life PCM Long Life Assurance PCR ※ I : Leakage Current(µA), C : Rated Capacitance(µF), V : Rated Voltage(V) φD L A B C E H Size 8.0 6.9 9.0 8.3 8.3 3.2 0.8 to 1.1 φ8 × 7L 8.0 9.9 9.0 8.3 8.3 3.2 0.8 to 1.1 φ8 ×10L 8.0 11.9 9.0 8.3 8.3 3.2 0.8 to 1.1 φ8 ×12L 10.0 7.9 11.0 10.3 10.3 4.6 0.8 to 1.1 φ10 × 8L 6.3 7.9 7.3 6.6 6.6 2.1 0.5 to 0.8 φ6.3 × 8L 6.3 5.9 7.3 6.6 6.6 2.1 0.5 to 0.8 φ6.3 × 6L 10.0 9.9 11.0 10.3 10.3 4.6 0.8 to 1.1 φ10 ×10L 10.0 12.6 11.0 10.3 10.3 4.6 0.8 to 1.1 φ10×12.7L (mm) Code C V 16 D E V H J Voltage K (mm) Standard Size φD L A B C E H φ 8 × 7L 8.0 6.9 9.0 8.3 8.3 3.2 0.8 to 1.1 φ 6.3 × 6L 6.3 5.9 7.3 6.6 6.6 2.1 0.5 to 0.8 φ 8 × 10L 8.0 9.9 9.0 8.3 8.3 3.2 0.8 to 1.1 φ 6.3 × 8L 6.3 7.9 7.3 6.6 6.6 2.1 0.5 to 0.8 φ 8 × 12L 8.0 11.9 9.0 8.3 8.3 3.2 0.8 to 1.1 φ10 × 8L 10.0 7.9 11.0 10.3 10.3 4.6 0.8 to 1.1 φ10 × 10L 10.0 9.9 11.0 10.3 10.3 4.6 0.8 to 1.1 φ10 × 12.7L 10.0 12.6 11.0 10.3 10.3 4.6 0.8 to 1.1 4J[F φ×- UP φ×- UP φ×- UP φ×- UP (mm) Vibration Resistance Frequency coefficient of rated ripple current Frequency Coefficient 120Hz 1kHz 10kHz 100kHz or more 0.05 0.30 0.70 1.00 CAT.8100N

（V） （code） Surge Voltage (V) Rated Capacitance （µF） Case Size φD×L （mm）tan δ Leakage Current （µA） Initial ESR (mΩ) （20℃/100kHz） Low temp. ESR after Endurance (mΩ) （−40℃ /100kHz） Rated Ripple （mArms） （125℃ /100kHz） Part Number at 20℃ after 2 minutes ） （1C） 20 120 6.3×6 0.08 57 36 72 1200 PCM1C121MCL1GS 220 ■ 6.3×8 0.08 105 23 46 1700 PCM1C221MCL4GS 220 8×7 0.08 105 30 60 1500 PCM1C221MCL1GS 470 ▲ 8×10 0.08 225 17 34 2400 PCM1C471MCL6GS 470 10×8 0.08 225 22 44 1900 PCM1C471MCL1GS 560 8×12 0.08 268 16 32 2700 PCM1C561MCL1GS 680 10×10 0.08 326 19 38 2300 PCM1C681MCL1GS 1000 10×12.7 0.08 480 13 26 2800 PCM1C102MCL1GS （1D） 25 100 6.3×6 0.08 60 41 82 1200 PCM1D101MCL1GS 150 ■ 6.3×8 0.08 90 25 50 1700 PCM1D151MCL4GS 150 8×7 0.08 90 39 78 1700 PCM1D151MCL1GS 330 ▲ 8×10 0.08 198 19 38 2400 PCM1D331MCL6GS 330 10×8 0.08 198 23 46 2000 PCM1D331MCL1GS 470 8×12 0.08 282 18 36 2800 PCM1D471MCL1GS 560 10×10 0.08 336 20 40 2500 PCM1D561MCL1GS 680 10×12.7 0.08 408 14 28 3500 PCM1D681MCL1GS （1E） 31 56 6.3×6 0.08 42 43 86 1200 PCM1E560MCL1GS 100 ■ 6.3×8 0.08 75 27 54 1700 PCM1E101MCL4GS 100 8×7 0.08 75 41 82 1700 PCM1E101MCL1GS 220 ▲ 8×10 0.08 165 20 40 2400 PCM1E221MCL6GS 220 10×8 0.08 165 24 48 2000 PCM1E221MCL1GS 270 8×12 0.08 202 19 38 2800 PCM1E271MCL1GS 330 10×10 0.08 247 20 40 2500 PCM1E331MCL1GS 470 10×12.7 0.08 352 15 30 3500 PCM1E471MCL1GS （1V） 43 47 6.3×6 0.08 49 48 96 1200 PCM1V470MCL1GS 68 ■ 6.3×8 0.08 71 31 62 1700 PCM1V680MCL4GS 68 8×7 0.08 71 44 88 1700 PCM1V680MCL1GS 150 ▲ 8×10 0.08 157 22 44 2400 PCM1V151MCL6GS 150 10×8 0.08 157 25 50 2000 PCM1V151MCL1GS 220 8×12 0.08 231 21 42 2800 PCM1V221MCL1GS 270 10×10 0.08 283 20 40 2500 PCM1V271MCL1GS 330 10×12.7 0.08 346 16 32 3500 PCM1V331MCL1GS （1H） 63 22 6.3×6 0.08 33 50 100 1000 PCM1H220MCL1GS 39 ■ 6.3×8 0.08 58 36 72 1200 PCM1H390MCL4GS 39 8×7 0.08 58 45 90 1600 PCM1H390MCL1GS 82 ▲ 8×10 0.08 123 26 52 2100 PCM1H820MCL6GS 82 10×8 0.08 123 34 68 2000 PCM1H820MCL1GS 120 △ 8 ×12 0.08 180 25 50 2500 PCM1H121MCL2GS 120 10×10 0.08 180 25 50 2500 PCM1H121MCL1GS 180 10×12.7 0.08 270 19 38 3200 PCM1H181MCL1GS （1J） 79 12 6.3×6 0.08 22 51 102 1000 PCM1J120MCL1GS 22 ■ 6.3×8 0.08 41 45 90 1200 PCM1J220MCL4GS 22 8×7 0.08 41 48 96 1600 PCM1J220MCL1GS 39 8×10 0.08 73 28 56 2100 PCM1J390MCL1GS 47 10×8 0.08 88 35 70 2000 PCM1J470MCL1GS 56 8×12 0.08 105 27 54 2500 PCM1J560MCL1GS 68 10×10 0.08 128 28 56 2500 PCM1J680MCL1GS 100 10×12.7 0.08 189 24 48 3200 PCM1J101MCL1GS （1K） 100 12 6.3×8 0.08 28 50 100 1000 PCM1K120MCL1GS 27 8×10 0.08 64 38 76 1400 PCM1K270MCL1GS 39 8×12 0.08 93 35 70 1800 PCM1K390MCL1GS 47 10×10 0.08 112 33 66 1800 PCM1K470MCL1GS 68 10×12.7 0.08 163 28 56 2200 PCM1K680MCL1GS CONDUCTIVE POLYMER ALUMINUM SOLID ELECTROLYTIC CAPACITORS Dimensions No marked, 1 will be put at 12th digit of type numbering system. : In this case, 2 will be put at 12th digit of type numbering system. : In this case, 4 will be put at 12th digit of type numbering system. : In this case, 6 will be put at 12th digit of type numbering system. For taping specifications, recommended land size/soldering by reflow and minimum order quantity, please refer to the Guidelines for Aluminum Electrolytic Capacitors. CAT.8100N