PCK NICHICON | Alldatasheet
Document overview
- Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
- PDF pages: 2
Technical content
CAT.8100H CONDUCTIVE POLYMER ALUMINUM SOLID ELECTROLYTIC CAPACITORS PCK Chip Type, Ultra-low ESR Specifications Temperature Characteristics (Max.Impedance Ratio) Category Temperature Range Rated Voltage Range Rated Capacitance Range Capacitance Tolerance Tangent of loss angle (tan δ) ESR ( 1) Leakage Current ( 2) Performance CharacteristicsItem –55 to +105°C 2.5 to 6.3V 220 to 2200µF ± 20% at 120Hz, 20°C Less than or equal to the specified value at 120Hz, 20°C Less than or equal to the specified value at 100kHz, 20°C Less than or equal to the specified value . After 2 minutes' application of rated voltage at 20°C Endurance Damp Heat (Steady State) Resistance to Soldering Heat Marking The specifications listed at right shall be met when the capacitors are restored to 20°C after the rated voltage is applied for 2000 hours at 105°C. The specifications listed at right shall be met when the capacitors are restored to 20°C after the rated voltage is applied for 1000 hours at 60°C, 90% RH. After soldering the capacitor under the soldering conditions prescribed here, the capacitor shall meet the specifications listed at right. Pre-heating shall be done at 150 to 200°C and for 60 to 180 sec. The duration for over +230°C temperature at capacitor surface shall not exceed 60 seconds. In case peak temperature is 250°C or less, reflow soldering shall be two times maximum. In case peak temperature is 260°C or less, reflow soldering shall be once. Measurement for solder temperature profile shall be made at the capacitor top and the terminal. Navy blue print on the case top Capacitance change tan δ Leakage current ( 2) ESR ( 1) Within ± 20% of the initial capacitance value ( 3) 150% or less than the initial specified value 150% or less than the initial specified value Less than or equal to the initial specified value Capacitance change tan δ Leakage current ( 2) ESR ( 1) Within ± 20% of the initial capacitance value ( 3) 150% or less than the initial specified value 150% or less than the initial specified value Less than or equal to the initial specified value Capacitance change tan δ Leakage current ( 2) ESR ( 1) Within ± 10% of the initial capacitance value ( 3) 130% or less than the initial specified value 130% or less than the initial specified value Less than or equal to the initial specified value Ultra-low ESR, Higher Capacitance, High ripple current. Load life of 2000 hours at 105°C. SMD type : Lead free reflow soldering condition at 260°C peak correspondence. Compliant to the RoHS directive (2011/65/EU). AEC-Q200 compliant. Please contact us for details. 1 ESR should be measured at both of the terminal ends closest where the terminals protrude through the plastic platform. 2 Conditioning : If any doubt arises, measure the leakage current after the voltage treatment of applying DC rated voltage continuously to the capacitor for 120 minutes at 105°C. 3 Initial value : The value before test of examination of resistance to soldering. P C K J M C O G S Configuration Taping code Capacitance tolerance (±20%) Rated capacitance (220µF) Rated voltage (6.3V) Series name Type C K 2 2 0 j 9 4 1 H 0.3 MAX. φD±0.5 B±0.2 A±0.2 C±0.2 0.5 MAX. E LSeries Voltage ( j:6.3v) Plastic platform Lot No.Capacitance Negative Positive +0.1 -0.4 Dimensions Type numbering system (Example : 6.3V 220µF) Voltage V 2.5 4 6.3 Code e g j Size φD L A B C E H φ6.3 × 6L 6.3 5.9 7.3 6.6 6.6 2.1 0.5 to 0.8 φ8 × 7L 8.0 6.9 9.0 8.3 8.3 3.2 0.8 to 1.1 φ10 × 8L 10.0 7.9 11.0 10.3 10.3 4.6 0.8 to 1.1 φ10 × 10L 10.0 9.9 11.0 10.3 10.3 4.6 0.8 to 1.1 (mm) Dimension table in next page. PCKPCJ Low ESR Frequency coefficient of rated ripple current
0 Frequency0/
120Hz 1kHz 10kHz 100kHz or more 0.05 0.30 0.70 1.00
CAT.8100H CONDUCTIVE POLYMER ALUMINUM SOLID ELECTROLYTIC CAPACITORS PCK Dimensions Taping specifications are given in page 23. Recommended land size, soldering by reflow are given in page 18, 19. Please refer to page 3 for the minimum order quantity. Rated ripple current (mArms) at 105°C 100kHz Rated Capacitance (µF) Rated Voltage (V)(code) Surge Voltage (V) Leakage Current (µA) ESR (mΩ) (at 100kHz 20°C) Rated Ripple (mArms)tan δ Part NumberCase Size φD × L (mm) 2.5 (0E) 6.3 (0J) (0G) 2.8 7.2 4.6 390 560 680 1200 2200 330 470 560 1000 1800 220 330 390 820 1500 293 420 510 900 1650 396 564 672 1200 2160 416 624 737 1550 2835 3900 4500 4500 5000 6000 3900 4500 4500 5000 6000 3900 4500 4500 5000 6000 PCK0E391MCO1GS PCK0E561MCO1GS PCK0E681MCO1GS PCK0E122MCO1GS PCK0E222MCO1GS PCK0G331MCO1GS PCK0G471MCO1GS PCK0G561MCO1GS PCK0G102MCO1GS PCK0G182MCO1GS PCK0J221MCO1GS PCK0J331MCO1GS PCK0J391MCO1GS PCK0J821MCO1GS PCK0J152MCO1GS 0.12 0.12 0.12 0.12 0.12 0.12 0.12 0.12 0.12 0.12 0.12 0.12 0.12 0.12 0.12 6.3 × 6 8 × 7 8 × 7 10 × 8 10 × 10 6.3 × 6 8 × 7 8 × 7 10 × 8 10 × 10 6.3 × 6 8 × 7 8 × 7 10 × 8 10 × 10