PCH1C102MCL1GS

PCH_V01 NICHICON | Alldatasheet

Document overview

• Manufacturer or author: Provided By alldatasheet.com(free datasheet download site)
• PDF pages: 2

Technical content

CONDUCTIVE POLYMER ALUMINUM SOLID ELECTROLYTIC CAPACITORS PCH Chip Type, Higher Capacitance High Temperature Range Specifications Temperature Characteristics (Max.Impedance Ratio) Category Temperature Range Rated Voltage Range Rated Capacitance Range Capacitance Tolerance Tangent of loss angle (tan δ) ESR ( 1) Leakage Current ( 2) Performance CharacteristicsItem –55 to +135°C 16 to 80V 12 to 1000μF ± 20% at 120Hz, 20°C Less than or equal to the specified value at 120Hz, 20°C Less than or equal to the specified value at 100kHz, 20°C After 2 minutes' application of rated voltage, leakage current is not more than 0.03CV or 3(μA), whichever is greater. Endurance Shelf Life ESR after Endurance ( 1) Damp Heat (Steady State) Resistance to Soldering Heat Marking The specifications listed at right shall be met when the capacitors are restored to 20°C after the rated voltage is applied for 4000 hours at 135°C. Less than or equal to the specified value at 100kHz, -40°C The specifications listed at right shall be met when the capacitors are restored to 20°C after the rated voltage is applied for 2000 hours at 85°C, 85% RH. After soldering the capacitor under the soldering conditions prescribed here, the capacitor shall meet the specifications listed at right. Pre-heating shall be done at 150 to 200°C and for 60 to 180 sec. The duration for over +230°C temperature at capacitor surface shall not exceed 60 seconds. In case peak temperature is 260°C or less, reflow soldering shall be two times maximum. Measurement for solder temperature profile shall be made at the capacitor top. Navy blue print on the case top Capacitance change tan δ Leakage current ( 2) ESR ( 1) Within ± 20% of initial capacitance value ( 3) 150% or less of the initial specified value 200% or less of the initial specified value Less than or equal to the initial specified value Capacitance change tan δ Leakage current ( 2) ESR ( 1) Within ± 20% of initial capacitance value ( 3) 150% or less of the initial specified value 200% or less of the initial specified value Less than or equal to the initial specified value Capacitance change tan δ Leakage current ( 2) ESR ( 1) Within ± 10% of the initial capacitance value ( 3) 130% or less than the initial specified value 130% or less than the initial specified value Less than or equal to the initial specified value High reliability, High voltage (to 80V). Low ESR, High ripple current. Long life of 4000 hours at 135°C. SMD type : Lead free reflow soldering condition at 260°C peak complete correspondence. Compliant to the RoHS directive (2011/65/EU,(EU)2015/863). ESR after Endurance at -40°C. AEC-Q200 compliant. Please contact us for details. 1 ESR should be measured at both of the terminal ends closest where the terminals protrude through the plastic platform. 2 Conditioning : If any doubt arises, measure the leakage current after the voltage treatment of applying DC rated voltage continuously to the capacitor for 120 minutes at 105°C. 3 Initial value : The value before test of examination of resistance to soldering. P C H V M C L 1 1 G S Configuration Taping code Size code Capacitance tolerance (±20%) Rated capacitance (150µF) Rated voltage (35V) Series name Type Standard Vibration Resistance codeConfiguration L S Type numbering system (Example : 35V 150 μF) After storing the capacitors under no load at 135°C for 1000 hours and then performing voltage treatment based on JIS C 5101-4 clause 4.1 at 20°C, they shall meet the specified values for the endurance characteristics listed above. C H 1 5 0 V 0 1 2 H 0.3 MAX. φD±0.5 B±0.2 A±0.2 C±0.2 0.5 MAX. E φ6.3:L±0.3 φ8,10:L±0.5 Series Voltage (V:35V) Plastic platform Lot No.Capacitance Negative PositiveStandard Negative PositiveVibration Resistance H 0.3 MAX. φD±0.5 B±0.2 A±0.2 C±0.2 0.5 MAX.E L±0.5 Plastic platform Aid electrode C H 1 5 0 V 0 1 2 Series Voltage (V:35V) Lot No.Capacitance Dimensions NEW PCH PCRPCZ High Temperature High Temperature The vibration structure-resistant product is also available upon request, please ask for details. ( ) : Size of the vibration structure-resistant product. Frequency coefficient of rated ripple current Frequency0/ Coefficient 120Hz 1kHz 10kHz 100kHz or more 0.05 0.30 0.70 1.00 (mm) Standard Size φD L A B C E H φ8 × 7L 8.0 6.9 9.0 8.3 8.3 3.2 0.8 to 1.1 φ6.3 × 6L 6.3 5.9 7.3 6.6 6.6 2.1 0.5 to 0.8 φ8 × 10L 8.0 9.9 9.0 8.3 8.3 3.2 0.8 to 1.1 φ6.3 × 8L 6.3 7.9 7.3 6.6 6.6 2.1 0.5 to 0.8 φ8 × 12L 8.0 11.9 9.0 8.3 8.3 3.2 0.8 to 1.1 φ10 × 8L 10.0 7.9 11.0 10.3 10.3 4.6 0.8 to 1.1 φ10 × 10L 10.0 9.9 11.0 10.3 10.3 4.6 0.8 to 1.1 φ10 × 12.7L 10.0 12.6 11.0 10.3 10.3 4.6 0.8 to 1.1 (mm) Vibration Resistance Size φD L A B C E H φ10 × 10.5L 10.0 10.0 11.0 10.3 10.3 4.6 1.1 to 1.5 φ6.3 × 8L 6.3 7.5 7.3 6.6 6.6 2.5 0.5 to 0.8 φ10 × 13.2L 10.0 12.7 11.0 10.3 10.3 4.6 1.1 to 1.5 φ8 × 10.5L 8.0 10.0 9.0 8.3 8.3 3.1 1.1 to 1.5 Voltage V 16 20 25 35 50 63 80 Code C D E V H J K Dimension table in next page.

CONDUCTIVE POLYMER ALUMINUM SOLID ELECTROLYTIC CAPACITORS PCH Dimensions 100 102 100 0.08 0.08 0.08 0.08 0.08 0.08 0.08 0.08 0.08 0.08 0.08 0.08 0.08 0.08 0.08 0.08 0.08 0.08 0.08 0.08 0.08 0.08 0.08 0.08 0.08 0.08 0.08 0.08 0.08 0.08 0.08 0.08 0.08 0.08 0.08 0.08 0.08 0.08 0.08 0.08 0.08 0.08 0.08 0.08 0.08 0.08 0.08 0.08 0.08 0.08 0.08 0.08 0.08 6.3 × 6 6.3 × 8 8 × 7 8 × 10 10 × 8 8 × 12 10 × 10 10 × 12.7 6.3 × 6 6.3 × 8 8 × 7 8 × 10 10 × 8 8 × 12 10 × 10 10 × 12.7 6.3 × 6 6.3 × 8 8 × 7 8 × 10 10 × 8 8 × 12 10 × 10 10 × 12.7 6.3 × 6 6.3 × 8 8 × 7 8 × 10 10 × 8 8 × 12 10 × 10 10 × 12.7 6.3 × 6 6.3 × 8 8 × 7 8 × 10 10 × 8 8 × 12 10 × 10 10 × 12.7 6.3 × 6 6.3 × 8 8 × 7 8 × 10 10 × 8 8 × 12 10 × 10 10 × 12.7 6.3 × 8 8 × 10 8 × 12 10 × 10 10 × 12.7 PCH1C121MCL1GS PCH1C221MCL4GS PCH1C221MCL1GS PCH1C471MCL6GS PCH1C471MCL1GS PCH1C561MCL1GS PCH1C681MCL1GS PCH1C102MCL1GS PCH1D101MCL1GS PCH1D151MCL4GS PCH1D151MCL1GS PCH1D331MCL6GS PCH1D331MCL1GS PCH1D471MCL1GS PCH1D561MCL1GS PCH1D681MCL1GS PCH1E560MCL1GS PCH1E101MCL4GS PCH1E101MCL1GS PCH1E221MCL6GS PCH1E221MCL1GS PCH1E271MCL1GS PCH1E331MCL1GS PCH1E471MCL1GS PCH1V470MCL1GS PCH1V680MCL4GS PCH1V680MCL1GS PCH1V151MCL6GS PCH1V151MCL1GS PCH1V221MCL1GS PCH1V271MCL1GS PCH1V331MCL1GS PCH1H220MCL1GS PCH1H390MCL4GS PCH1H390MCL1GS PCH1H820MCL6GS PCH1H820MCL1GS PCH1H121MCL2GS PCH1H121MCL1GS PCH1H181MCL1GS PCH1J120MCL1GS PCH1J220MCL4GS PCH1J220MCL1GS PCH1J390MCL1GS PCH1J470MCL1GS PCH1J560MCL1GS PCH1J680MCL1GS PCH1J101MCL1GS PCH1K120MCL1GS PCH1K270MCL1GS PCH1K390MCL1GS PCH1K470MCL1GS PCH1K680MCL1GS 900 1500 1100 2400 1900 2700 2300 2500 900 1200 800 2300 1800 2500 2200 3000 900 1100 800 2300 1800 2300 2200 2900 800 1100 800 2200 1800 2300 2200 2800 700 900 900 2100 1600 2100 2100 2500 700 800 800 1900 1500 2100 2000 2100 800 1000 1100 1200 1500 ʢ1Eʣ ʢ1Vʣ 6350 ʢ1Hʣ 2016 ʢ1Cʣ 2520 ʢ1Dʣ 10080 ʢ1Kʣ ʢ1Jʣ 79 120 220 220 470 470 560 680 1000 100 150 150 330 330 470 560 680 100 100 220 220 270 330 470 150 150 220 270 330 120 120 180 100 Rated Voltage (V)(code) Surge Voltage (V) Rated Capacitance (µF) Case Size φD × L (mm) tan δ Part Number Low temp. ESR after Endurance (mΩ) (-40°C / 100kHz) Rated Ripple (mArms) (135°C / 100kHz) Initial ESR (mΩ) (20°C / 100kHz) : In this case, 6 will be put at 12th digit of type numbering system. : In this case, 4 will be put at 12th digit of type numbering system. : In this case, 2 will be put at 12th digit of type numbering system. No marked, 1 will be put at 12th digit of type numbering system. Rated ripple current (mArms) at 135°C 100kHz Taping specifications are given in page 23. Recommended land size, soldering by reflow are given in page 18, 19. Please refer to page 3 for the minimum order quantity.