PCH NICHICON | Alldatasheet
Document overview
- Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
- PDF pages: 2
Technical content
CONDUCTIVE POLYMER ALUMINUM SOLID ELECTROLYTIC CAPACITORS PCH Chip Type, Higher Capacitance High Temperature Range Specifications Temperature Characteristics (Max.Impedance Ratio) Category Temperature Range Rated Voltage Range Rated Capacitance Range Capacitance Tolerance Tangent of loss angle (tan δ) ESR ( 1) Leakage Current ( 2) Performance CharacteristicsItem –55 to +135°C 25 to 63V 22 to 470µF ± 20% at 120Hz, 20°C Less than or equal to the specified value at 120Hz, 20°C Less than or equal to the specified value at 100kHz, 20°C After 2 minutes' application of rated voltage, leakage current is not more than 0.03CV or 3(µA), whichever is greater. Endurance Shelf Life ESR after Endurance ( 1) Damp Heat (Steady State) Resistance to Soldering Heat Marking The specifications listed at right shall be met when the capacitors are restored to 20°C after the rated voltage is applied for 4000 hours at 135°C. Less than or equal to the specified value at 100kHz, -40°C The specifications listed at right shall be met when the capacitors are restored to 20°C after the rated voltage is applied for 2000 hours at 85°C, 85% RH. After soldering the capacitor under the soldering conditions prescribed here, the capacitor shall meet the specifications listed at right. Pre-heating shall be done at 150 to 200°C and for 60 to 180 sec. The duration for over +230°C temperature at capacitor surface shall not exceed 60 seconds. In case peak temperature is 260°C or less, reflow soldering shall be two times maximum. Measurement for solder temperature profile shall be made at the capacitor top and the terminal. Navy blue print on the case top Capacitance change tan δ Leakage current ( 2) ESR ( 1) Within ± 20% of initial capacitance value ( 3) 150% or less of the initial specified value 200% or less of the initial specified value Less than or equal to the initial specified value Capacitance change tan δ Leakage current ( 2) ESR ( 1) Within ± 20% of initial capacitance value ( 3) 150% or less of the initial specified value 200% or less of the initial specified value Less than or equal to the initial specified value Capacitance change tan δ Leakage current ( 2) ESR ( 1) Within ± 10% of the initial capacitance value ( 3) 130% or less than the initial specified value 130% or less than the initial specified value Less than or equal to the initial specified value High reliability, High voltage (to 63V). Low ESR, High ripple current. Long life of 4000 hours at 135°C. SMD type : Lead free reflow soldering condition at 260°C peak complete correspondence. Compliant to the RoHS directive (2011/65/EU). ESR after Endurance at -40°C. AEC-Q200 compliant. Please contact us for details. 1 ESR should be measured at both of the terminal ends closest where the terminals protrude through the plastic platform. 2 Conditioning : If any doubt arises, measure the leakage current after the voltage treatment of applying DC rated voltage continuously to the capacitor for 120 minutes at 105°C. 3 Initial value : The value before test of examination of resistance to soldering. P C H V M C L 1 1 G S Configuration Taping code Size code Capacitance tolerance (±20%) Rated capacitance (150µF) Rated voltage (35V) Series name Type Type numbering system (Example : 35V 150µF) PCH PCR After storing the capacitors under no load at 135°C for 1000 hours and then performing voltage treatment based on JIS C 5101-4 clause 4.1 at 20°C, they shall meet the specified values for the endurance characteristics listed above. C H 1 5 0 V 3 3 1 H 0.3 MAX. φD±0.5 B±0.2 A±0.2 C±0.2 0.5 MAX. E LSeries Voltage (V:35V) Plastic platform Lot No.Capacitance Negative Positive +0.1 -0.4 Dimensions NEW Voltage V 25 35 50 63 Code E V H J Size φD L A B C E H φ8 × 7L 8.0 6.9 9.0 8.3 8.3 3.2 0.8 to 1.1 × 10L 8.0 9.9 9.0 8.3 8.3 3.2 0.8 to 1.1 φ8 × 12L 8.0 11.9 9.0 8.3 8.3 3.2 0.8 to 1.1 φ10 × 8L 10.0 7.9 11.0 10.3 10.3 4.6 0.8 to 1.1 φ10 × 10L 10.0 9.9 11.0 10.3 10.3 4.6 0.8 to 1.1 φ10 × 12.7L 10.0 12.6 11.0 10.3 10.3 4.6 0.8 to 1.1 (mm) Frequency coefficient of rated ripple current
0 Frequency0/
120Hz 1kHz 10kHz 100kHz or more 0.05 0.30 0.70 1.00 High Temperature
CONDUCTIVE POLYMER ALUMINUM SOLID ELECTROLYTIC CAPACITORS PCH Dimensions Rated Voltage (V)(code) Surge Voltage (V) 800 1800 1400 2100 2200 2000 700 1700 1300 1800 2200 1900 700 1600 1200 1600 1700 1800 700 1500 1100 1700 1800 1600 0.08 0.08 0.08 0.08 0.08 0.08 0.08 0.08 0.08 0.08 0.08 0.08 0.08 0.08 0.08 0.08 0.08 0.08 0.08 0.08 0.08 0.08 0.08 0.08 8 × 7 8 × 10 10 × 8 8 × 12 10 × 10 10 × 12.7 8 × 7 8 × 10 10 × 8 8 × 12 10 × 10 10 × 12.7 100 220 220 270 330 470 150 150 220 270 330 3125 (1E) 4335 (1V) PCH1E101MCL1GS PCH1E221MCL6GS PCH1E221MCL1GS PCH1E271MCL1GS PCH1E331MCL1GS PCH1E471MCL1GS PCH1V680MCL1GS PCH1V151MCL6GS PCH1V151MCL1GS PCH1V221MCL1GS PCH1V271MCL1GS PCH1V331MCL1GS PCH1H390MCL1GS PCH1H820MCL6GS PCH1H820MCL1GS PCH1H121MCL2GS PCH1H121MCL1GS PCH1H181MCL1GS PCH1J220MCL1GS PCH1J390MCL1GS PCH1J470MCL1GS PCH1J560MCL1GS PCH1J680MCL1GS PCH1J101MCL1GS Rated Capacitance (µF) Case Size φD × L (mm) tan δ Part Number Low temp. ESR after Endurance (mΩ) (-40°C / 100kHz) Rated Ripple (mArms) (135°C / 100kHz) Initial ESR (mΩ) (20°C / 100kHz) 120 120 180 100 6350 (1H) 7963 (1J) 8 × 7 8 × 10 10 × 8 8 × 12 10 × 10 10 × 12.7 8 × 7 8 × 10 10 × 8 8 × 12 10 × 10 10 × 12.7 No marked, 1 will be put at 12th digit of type numbering system. : In this case, 2 will be put at 12th digit of type numbering system. : In this case, 6 will be put at 12th digit of type numbering system. October 2018