PCA

PCA NICHICON | Alldatasheet

Document overview

• Manufacturer or author: Provided By alldatasheet.com(free datasheet download site)
• PDF pages: 2

Technical content

Chip Type, High Reliability Specifications Temperature Characteristics (Max.Impedance Ratio) Category Temperature Range Rated Voltage Range Rated Capacitance Range Capacitance Tolerance Tangent of loss angle (tan δ) ESR ( 1) Leakage Current ( 2) Performance CharacteristicsItem –55 to +125°C 25 to 63V 47 to 470µF ± 20% at 120Hz, 20°C Less than or equal to the specified value at 120Hz, 20°C Less than or equal to the specified value at 100kHz, 20°C After 2 minutes' application of rated voltage, leakage current is not more than 0.03CV. Endurance Shelf Life ESR after Endurance ( 1) Damp Heat (Steady State) Resistance to Soldering Heat Marking The specifications listed at right shall be met when the capacitors are restored to 20°C after D.C. bias plus rated ripple current is applied for 4000 hours at 125°C, the peak voltage shall not exceed the rated voltage. Less than or equal to the specified value at 100kHz, -40°C The specifications listed at right shall be met when the capacitors are restored to 20°C after the rated voltage is applied for 2000 hours at 85°C, 85% RH. After soldering the capacitor under the soldering conditions prescribed here, the capacitor shall meet the specifications listed at right. Pre-heating shall be done at 150 to 200°C and for 60 to 180 sec. The duration for over +230°C temperature at capacitor surface shall not exceed 60 seconds. In case peak temperature is 260°C or less, reflow soldering shall be two times maximum. Measurement for solder temperature profile shall be made at the capacitor top. Navy blue print on the case top Capacitance change tan δ Leakage current ( 2) ESR ( 1) Within ± 20% of initial capacitance value ( 3) 150% or less of the initial specified value 200% or less of the initial specified value Less than or equal to the initial specified value Capacitance change tan δ Leakage current ( 2) ESR ( 1) Within ± 20% of initial capacitance value ( 3) 150% or less of the initial specified value 200% or less of the initial specified value Less than or equal to the initial specified value Capacitance change tan δ Leakage current ( 2) ESR ( 1) Within ± 10% of the initial capacitance value ( 3) 130% or less than the initial specified value 130% or less than the initial specified value Less than or equal to the initial specified value

1 ESR should be measured at both of the terminal ends closest where the terminals

protrude through the plastic platform.

2 Conditioning : If any doubt arises, measure the leakage current after the voltage treatment of

applying DC rated voltage continuously to the capacitor for 120 minutes at 105°C. 3 Initial value : The value before test of examination of resistance to soldering. Dimension table in next page. After storing the capacitors under no load at 125°C for 1000 hours and then performing voltage treatment based on JIS C 5101-4 clause 4.1 at 20°C, they shall meet the specified values for the endurance characteristics listed above. P C A E M C L 1 1 G S Configuration Taping code Size code Capacitance tolerance (±20%) Rated capacitance (220µF) Rated voltage (25V) Series name Type Type numbering system (Example : 25V 220µF) C A 2 2 0 E 3 3 1 H 0.3 max. φD±0.5 B±0.2 A±0.2 C±0.2 0.5 max. E Series Voltage (E:25V) Plastic platform Lot No.Capacitance Negative Positive L±0.5 Dimensions ※ I : Leakage Current(µA), C : Rated Capacitance(µF), V : Rated Voltage(V) High reliability, Ripple current superimposition guaranteed products. Low ESR, High ripple current. Long life of 4000 hours at 125°C. SMD type : Lead free reflow soldering condition at 260°C peak complete correspondence. Compliant to the RoHS directive (2011/65/EU,(EU)2015/863). ESR after Endurance at -40°C. AEC-Q200 compliant. Please contact us for details. PCRPCA Compliant to high ripple current. φD L A B C E H Size 8.0 9.9 9.0 8.3 8.3 3.2 0.8 to 1.1 φ8 ×10L 8.0 11.9 9.0 8.3 8.3 3.2 0.8 to 1.1 φ8 ×12L 10.0 9.9 11.0 10.3 10.3 4.6 0.8 to 1.1 φ10 ×10L 10.0 12.6 11.0 10.3 10.3 4.6 0.8 to 1.1 φ10×12.7L (mm) Code V E V H J Voltage Standard Frequency coefficient of rated ripple current

0 Frequency0/

120Hz 1kHz 10kHz 100kHz or more 0.05 0.30 0.70 1.00 NEW CONDUCTIVE POLYMER ALUMINUM SOLID ELECTROLYTIC CAPACITORS CAT.8100N

（V） （code） Surge Voltage (V) Rated Capacitance （µF） Case Size φD×L （mm）tan δ Leakage Current （µA） Initial ESR (mΩ) （20℃/100kHz) Low temp. ESR after Endurance (mΩ) （−40℃ /100kHz） Rated Ripple （mArms） （125℃ /100kHz） Part Number at 20℃ after 2 minutes ） （1E） 31 220 8×10 0.08 165 20 40 3900 PCA1E221MCL1GS 270 8×12 0.08 202 19 38 4000 PCA1E271MCL1GS 330 10×10 0.08 247 20 40 4600 PCA1E331MCL1GS 470 10×12.7 0.08 352 15 30 5100 PCA1E471MCL1GS （1V） 43 150 8×10 0.08 157 22 44 3900 PCA1V151MCL1GS 220 8×12 0.08 231 21 42 3900 PCA1V221MCL1GS 270 10×10 0.08 283 20 40 4500 PCA1V271MCL1GS 330 10×12.7 0.08 346 16 32 5000 PCA1V331MCL1GS （1H） 63 68 8×10 0.08 102 26 52 3600 PCA1H680MCL1GS 120 △ 8×12 0.08 180 25 50 3700 PCA1H121MCL2GS 120 10×10 0.08 180 25 50 4300 PCA1H121MCL1GS 180 10×12.7 0.08 270 19 38 4600 PCA1H181MCL1GS （1J） 79 47 8×10 0.08 88 28 56 3600 PCA1J470MCL1GS 68 8×12 0.08 128 27 54 3700 PCA1J680MCL1GS 82 10×10 0.08 154 28 56 4300 PCA1J820MCL1GS 120 10×12.7 0.08 226 24 48 4600 PCA1J121MCL1GS Dimensions No marked, 1 will be put at 12th digit of type numbering system. : In this case, 2 will be put at 12th digit of type numbering system. CONDUCTIVE POLYMER ALUMINUM SOLID ELECTROLYTIC CAPACITORS For taping specifications, recommended land size/soldering by reflow and minimum order quantity, please refer to the Guidelines for Aluminum Electrolytic Capacitors. CAT.8100N