PC2807

PC2807_15 RENESAS | Alldatasheet

Document overview

• Manufacturer or author: Provided By www.digicamel.com(FREE DATASHEET DOWNLOAD SITE)
• PDF pages: 10

Technical content

To our customers, Old Company Name in Catalogs and Other Documents On April 1st, 2010, NEC Electronics Corporation merged with Renesas Technology Corporation, and Renesas Electronics Corporation took over all the business of both companies. Therefore, although the old company name remains in this document, it is a valid Renesas Electronics document. We appreciate your understanding. Renesas Electronics website: http://www.renesas.com April 1st, 2010 Renesas Electronics Corporation Issued by: Renesas Electronics Corporation (http://www.renesas.com) Send any inquiries to http://www.renesas.com/inquiry.

1. All information included in this document is current as of the date this document is issued. Such information, however, is subject to change without any prior notice. Before purchasing or using any Renesas Electronics products listed herein, please confirm the latest product information with a Renesas Electronics sales office. Also, please pay regular and careful attention to additional and different information to be disclosed by Renesas Electronics such as that disclosed through our website. 2. Renesas Electronics does not assume any liability for infringeme nt of patents, copyrights, or other intellectual property rights of third parties by or arising from the use of Renesas Electronics products or technical information described in this document. No license, express, implied or otherwise, is granted hereby under any patents, copyrights or other intellectual property rights of Renesas Electronics or others. 3. You should not alter, modify, copy, or otherwise misappropriate any Renesas Electronics product, whether in whole or in part. 4. Descriptions of circuits, software and other related informat ion in this document are provided only to illustrate the operation of semiconductor products and application examples. You are fully responsible for the incorporation of these circuits, software, and information in the design of your equipment. Renesas Electronics assumes no responsibility for any losses incurred by you or third parties arising from the use of these circuits, software, or information. 5. When exporting the products or technology described in this doc ument, you should comply with the applicable export control laws and regulations and follow the procedures required by such laws and regulations. You should not use Renesas Electronics products or the technology described in this document for any purpose relating to military applications or use by the military, including but not limited to the development of weapons of mass destruction. Renesas Electronics products and technology may not be used for or incorporated into any products or systems whose manufacture, use, or sale is prohibited under any applicable domestic or foreign laws or regulations. 6. Renesas Electronics has used reasonable care in preparing th e information included in this document, but Renesas Electronics does not warrant that such information is error free. Renesas Electronics assumes no liability whatsoever for any damages incurred by you resulting from errors in or omissions from the information included herein. 7. Renesas Electronics products ar e classified according to the following three quality grades: “Standard”, “High Quality”, and “Specific”. The recommended applications for each Renesas Electronics product depends on the product’s quality grade, as indicated below. You must check the quality grade of each Renesas Electronics product before using it in a particular application. You may not use any Renesas Electronics product for any application categorized as “Specific” without the prior written consent of Renesas Electronics. Further, you may not use any Renesas Electronics product for any application for which it is not intended without the prior written consent of Renesas Electronics. Renesas Electronics shall not be in any way liable for any damages or losses incurred by you or third parties arising from the use of any Renesas Electronics product for an application categorized as “Specific” or for which the product is not intended where you have failed to obtain the prior written consent of Renesas Electronics. The quality grade of each Renesas Electronics product is “Standard” unless otherwise expressly specified in a Renesas Electronics data sheets or data books, etc. “Standard”: Computers; office equipmen t; communications equipment; test and measurement equipment; audio and visual equipment; home electronic appliances; machine tools; personal electronic equipment; and industrial robots. “High Quality”: Transportation equi pment (automobiles, trains, ships, etc.); traffic control systems; anti-disaster systems; anti- crime systems; safety equipment; and medical equipment not specifically designed for life support. “Specific”: Aircraft; aerospace equipment; submersible repeaters; nuclear reactor control systems; medical equipment or systems for life support (e.g. artificial life support devices or systems), surgical implantations, or healthcare intervention (e.g. excision, etc.), and any other applications or purposes that pose a direct threat to human life. 8. You should use the Renesas Electronics pr oducts described in this document within the range specified by Renesas Electronics, especially with respect to the maximum rating, operating supply voltage range, movement power voltage range, heat radiation characteristics, installation and other product characteristics. Renesas Electronics shall have no liability for malfunctions or damages arising out of the use of Renesas Electronics products beyond such specified ranges. 9. Although Renesas Electronics endeavors to improve the quality and reliability of its products, semiconductor products have specific characteristics such as the occurrence of failure at a certain rate and malfunctions under certain use conditions. Further, Renesas Electronics products are not subject to radiation resistance design. Please be sure to implement safety measures to guard them against the possibility of physical injury, and injury or damage caused by fire in the event of the failure of a Renesas Electronics product, such as safety design for hardware and software including but not limited to redundancy, fire control and malfunction prevention, appropriate treatment for aging degradation or any other appropriate measures. Because the evaluation of microcomputer software alone is very difficult, please evaluate the safety of the final products or system manufactured by you. 10. Please contact a Renesa s Electronics sales office for details as to environmental matters such as the environmental compatibility of each Renesas Electronics product. Please use Renesas Electronics products in compliance with all applicable laws and regulations that regulate the inclusion or use of controlled substances, including without limitation, the EU RoHS Directive. Renesas Electronics assumes no liability for damages or losses occurring as a result of your noncompliance with applicable laws and regulations. 11. This document may not be reproduced or duplicated, in any form, in whole or in part, without prior written consent of Renesas Electronics. 12. Please contact a Renesa s Electronics sales office if you have any questions regarding the information contained in this document or Renesas Electronics products, or if you have any other inquiries. (Note 1) “Renesas Electronics” as used in this document means Renesas Electronics Corporation and also includes its majority- owned subsidiaries. (Note 2) “Renesas Electronics product(s)” means any product developed or manufactured by or for Renesas Electronics.

The information in this document is subject to change without notice. Before using this document, please confirm that this is the latest version. Not all devices/types available in every country. Please check with local NEC representative for availability and additional information. 1998, 2000 BiCMOS INTEGRATED CIRCUIT µ µ µ µ PC2807,2807A PREAMPLIFIER FOR INFRARED REMOTE CONTROLLER DATA SHEET Document No. S13198EJ2V0DS00 (2nd edition) Date Published December 2000 NS CP (K) Printed in Japan The mark # shows major revised points.

DESCRIPTION

The µ PC2807 and 2807A are semiconductors integrated circuit developed as preamplifiers for the receiver module of infrared remote controllers. These preamplifiers can be directly connected to a PIN photodiode, and integrate a high-gain first stage amplifier, limiter, bandpass filter, detector circuit, and waveform-shaping circuit on a single chip.

FEATURES

• Only PIN photodiode required as an external component.
• Following carrier frequencies (fO ) selectable (six types): µ PC2807A : fO = 40.0 kHz
• Fixed trap frequency fT = 54 kHz (when carrier frequency is 56.7 kHz, trap frequency is 76 kHz)
• Active-low output
• Supplied in form of wafer APPLICATION
• Receiver module of infrared remote controller

ORDERING INFORMATION

Part Number Condition in shipment µ PC2807W Wafer µ PC2807AW Wafer Contact an NEC sales representative in advance since a memorandum on product quality need to be prepared for shipment in the form of wafer.

µ µ µ µ PC2807, 2807A BLOCK DIAGRAM 13 12 11 10 TRAP skip First-stage amplifier Waveform-shaping circuit Limiter amplifier Trimming circuit fO setting 8 7 GND1 GND2PAD6 PAD3 PAD4 PAD5 9 5 OUT S3 S2 PAD1 IN TRAP BPF VCC Detector 22 kΩ I/V ABLC Carrier elimination

Data Sheet S13198EJ2V0DS 3 µ µ µ µ PC2807, 2807A PAD FUNCTION Symbol Pad No. Function VCC 6 Power pad. Apply a voltage of 5 V ±10%. Connect an external smoothing filter if noise on power line is high. GND1 7 GND pad (for output transistor) GND2 8 GND pad (for circuits excluding output transistor) IN 9 Input pad. Internal impedance is 190 k Ω Typ. PIN photodiode can be directly connected. OUT 5 Output pad. Open-collector output with pull-up resistor (22 kΩ Typ.) To connect pull-up resistor, use resistor of 10 kΩ or higher. S1 1 BPF center frequency setting pads. S2 2 Connect pad corresponding to carrier frequency to be used to GND Note S3 4 PAD1 3 BPF output pad. Parameters such as voltage gain and BPF bandwidth can be tested. Do not connect this pad to anything on final assembly. PAD3 10 Test and trimming pads. Do not connect these pads to anything. PAD4 11 PAD5 12 PAD6 13 Note Connect each of BPF center frequency setting pads as follows depending on the carrier frequency.

• µ PC2807 Carrier Frequency S1 S2 S3 32.7 kHz GND Leave unconnected. Leave unconnected. 36.0 kHz GND GND GND 36.7 kHz Leave unconnected. GND GND 37.9 kHz Leave unconnected. Leave unconnected. Leave unconnected. 56.7 kHz Leave unconnected. Leave unconnected. GND
• µ PC2807A Carrier Frequency S1 S2 S3 40.0 kHz Leave unconnected. Leave unconnected. Leave unconnected.

µ µ µ µ PC2807, 2807A ELECTRICAL SPECIFICATIONS Absolute Maximum Ratings (TA ==== ++++25 ±±±±3°°°°C) Parameter Symbol Ratings Unit Supply voltage V CC 6.0 V Output sink current I OSINK 2.5 mA Input voltage V IN 0 to VCC V Storage temperature T stg −40 to + 125 °C Caution Product quality may suffer if the absolute maximum rating is exceeded even momentarily for any parameter. That is, the absolute maximum ratings are rated values at which the product is on the verge of suffering physical damage, and therefore the product must be used under conditions that ensure that the absolute maximum ratings are not exceeded. Recommended Operating Conditions (T Parameter Symbol Conditions Min. Typ. Max. Unit Supply voltage V CC 4.5 5.0 5.5 V Operating ambient temperature TA −25 +25 +80 °C

Data Sheet S13198EJ2V0DS 5 µ µ µ µ PC2807, 2807A Electrical Characteristics (TA = ++++25 ±±±±3°°°°C, VCC ==== 5 V) Parameter Symbol Conditions Min. Typ. Max. Unit Circuit current I CC With no signal applied. S1, S2, and S3: Leave unconnected. 1.2 1.6 1.9 mA Low-level output voltage 1 VOL1 Without external pull-up resistor − 0.05 0.4 V Low-level output voltage 2 VOL2 With external 10-kΩ pull-up resistor connected− 0.10 0.5 V High-level output voltage VOH 4.8 5.0 − V Voltage gain A v S1, S2, and S3: Leave unconnected., VIN = 30 dB µ V Note1 , f = 37.9 kHz Note2 70 78 84 dB BPF bandwidth f BW −3 dB bandwidth. S1, S2, S3: Leave unconnected., VIN = 30 dB µ V Note1 1.5 3.0 4.5 kHz Output pulse width 1 t BW1 S1, S2, and S3: Leave unconnected., VIN = 500 µ Vp-p, f = 37.9 kHz Note2 Burst length: 600 µ s, Cycle: 1.2 ms Note3 Average value of output from start of signal input to 60th pulse 400 600 800 µ s Output pulse width 2 t PW2 S1, S2, and S3: Leave unconnected., VIN = 50 mVp-p, f = 37.9 kHz Note2 Burst length: 600 µ s, Cycle: 1.2 ms Note3 Average value of output from start of signal input to 60th pulse 400 600 800 µ s 3. Input the following burst signal. 37.9-kHz carrier 600 µ s600 µ s600 µ s

µ µ µ µ PC2807, 2807A APPLICATION CIRCUIT EXAMPLE (at carrier frequency of 37.9 kHz) Remark f = 37.9 kHz for the µ PC2807. In the µ PC2807A, f = 40.0 kHz. 13 12 11 10 TRAP skip First-stage amplifier Waveform-shaping circuit Limiter amplifier Trimming circuit fO setting 8 7 GND1GND2 OUTPUT PAD6 PAD3 PAD4 PAD5 9 5 OUT S3 S2 PAD1 IN TRAP BPF 5 V VCC Detector 22 kΩ PIN Photo- diode I/V ABLC Carrier elimination

Data Sheet S13198EJ2V0DS 7 µ µ µ µ PC2807, 2807A NOTES FOR BiCMOS DEVICES

1 PRECAUTION AGAINST ESD FOR SEMICONDUCTORS

Note: Strong electric field, when exposed to a device, can cause destruction of the gate oxide and ultimately degrade the device operation. Steps must be taken to stop generation of static electricity as much as possible, and quickly dissipate it once, when it has occurred. Environmental control must be adequate. When it is dry, humidifier should be used. It is recommended to avoid using insulators that easily build static electricity. Semiconductor devices must be stored and transported in an anti-static container, static shielding bag or conductive material. All test and measurement tools including work bench and floor should be grounded. The operator should be grounded using wrist strap. Semiconductor devices must not be touched with bare hands. Similar precautions need to be taken for PW boards with semiconductor devices on it.

2 HANDLING OF UNUSED INPUT PINS

Note: No connection for device inputs can be cause of malfunction. If no connection is provided to the input pins, it is possible that an internal input level may be generated due to noise, etc., hence causing malfunction. Input levels of devices must be fixed high or low by using a pull-up or pull- down circuitry. Each unused pin should be connected to V DD or GND with a resistor, if it is considered to have a possibility of being an output pin. All handling related to the unused pins must be judged device by device and related specifications governing the devices.

3 STATUS BEFORE INITIALIZATION OF BiCMOS DEVICES

Note: Power-on does not necessarily define initial status of device. Production process of BiCMOS does not define the initial operation status of the device. Immediately after the power source is turned ON, the devices with reset function have not yet been initialized. Hence, power-on does not guarantee out-pin levels, I/O settings or contents of registers. Device is not initialized until the reset signal is received. Reset operation must be executed immediately after power-on for devices having reset function.

µ µ µ µ PC2807, 2807A M8E 00. 4 The information in this document is current as of December, 2000. The information is subject to change without notice. For actual design-in, refer to the latest publications of NEC's data sheets or data books, etc., for the most up-to-date specifications of NEC semiconductor products. Not all products and/or types are available in every country. Please check with an NEC sales representative for availability and additional information. No part of this document may be copied or reproduced in any form or by any means without prior written consent of NEC. NEC assumes no responsibility for any errors that may appear in this document. NEC does not assume any liability for infringement of patents, copyrights or other intellectual property rights of third parties by or arising from the use of NEC semiconductor products listed in this document or any other liability arising from the use of such products. No license, express, implied or otherwise, is granted under any patents, copyrights or other intellectual property rights of NEC or others. Descriptions of circuits, software and other related information in this document are provided for illustrative purposes in semiconductor product operation and application examples. The incorporation of these circuits, software and information in the design of customer's equipment shall be done under the full responsibility of customer. NEC assumes no responsibility for any losses incurred by customers or third parties arising from the use of these circuits, software and information. While NEC endeavours to enhance the quality, reliability and safety of NEC semiconductor products, customers agree and acknowledge that the possibility of defects thereof cannot be eliminated entirely. To minimize risks of damage to property or injury (including death) to persons arising from defects in NEC semiconductor products, customers must incorporate sufficient safety measures in their design, such as redundancy, fire-containment, and anti-failure features. NEC semiconductor products are classified into the following three quality grades: "Standard", "Special" and "Specific". The "Specific" quality grade applies only to semiconductor products developed based on a customer-designated "quality assurance program" for a specific application. The recommended applications of a semiconductor product depend on its quality grade, as indicated below. Customers must check the quality grade of each semiconductor product before using it in a particular application. "Standard":Computers, office equipment, communications equipment, test and measurement equipment, audio and visual equipment, home electronic appliances, machine tools, personal electronic equipment and industrial robots "Special": Transportation equipment (automobiles, trains, ships, etc.), traffic control systems, anti-disaster systems, anti-crime systems, safety equipment and medical equipment (not specifically designed for life support) "Specific": Aircraft, aerospace equipment, submersible repeaters, nuclear reactor control systems, life support systems and medical equipment for life support, etc. The quality grade of NEC semiconductor products is "Standard" unless otherwise expressly specified in NEC's data sheets or data books, etc. If customers wish to use NEC semiconductor products in applications not intended by NEC, they must contact an NEC sales representative in advance to determine NEC's willingness to support a given application. (Note) (1) "NEC" as used in this statement means NEC Corporation and also includes its majority-owned subsidiaries. (2) "NEC semiconductor products" means any semiconductor product developed or manufactured by or for NEC (as defined above).