PB8H CRYDOM | Alldatasheet
Document overview
- Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
- PDF pages: 3
Technical content
Input and output modules accepted interchangeably Operate with 5, 15 or 24 volt logic supplies Captive-screw retaining system for standard-size modules Plug-compatible logic connections Screw terminal barrier block for load connections Resident pull-up resistors 5 amp field-replaceable fuses (LITTLEFUSE #251005 or equivalent) All even-numbered logic connections are logic ground PB8H MECHANICAL SPECIFICATIONS LEDs indicate logic status MOUNTING BOARD Rev. 070808 8.25 (209,55) 7.5 (190,5) 4.0 (101,6) 3.5 (88,9) 0.25 (6,4) 0.375 (9,5) 0 1 2 3 4 5 6 7 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 5V JUMPERS PIN 1 PIN 49 PWR ON+5V GND
1 AMP FUSE
0.65 (16,5) 2.1 (53,3) THRU HOLE SWAGED STANDOFF LOGIC SUPPLY BARRIER STRIP REPLACEABLE 1 AMP LOGIC SUPPLY FUSE (see note 4) POWER BARRIER STRIP (see notes 2,3) REPLACEABLE 5 AMP LINE FUSES (8) (see note 5) SPARE 5 AMP LINE FUSE PULL UP RESISTOR 3.3K OHM (8) GORDOS DIGITAL I/O MODULES SOLD SEPERATELYLED STATUS INDICATORS SIGNAL INPUT/OUTPUT
50 CONDUCTOR MALE
(see note 1) NEGATIVE (-) LOGIC SUPPLY BUS TERMINATION JUMPERS CONNECTING LOGIC SUPPLY THRU HEADER CONNECTOR POSITIVE (+) LOGIC SUPPLY BUS TERMINATION 3) OPTIONAL JUMPERS ARE AVAILABLE TO INTERCONNECT BARRIER STRIP COMMONS. ORDER 1 EACH "JS8". 4) LITTLE FUSE 251001 OR EQUIVALENT. 5) LITTLE FUSE 251005 OR EQUIVALENT. SCREW TERMINAL NOTES: 1) CONNECTOR IS CIRCUIT ASSEMBLY CA-50H-2B-SR OR EQUIVALENT. 2) 6-32 SCREW TERMINAL BARRIER STRIPS ACCEPT WIRE SIZES FROM 24 TO 12 AWG. DIMENSIONS: INCHES (MILLIMETERS) TOLERANCE: 0.020 ( 0,50)+- NC NC PWR ON RESISTOR PULL UP 2-50EVEN PINS +5V GND 1 2 3 4 5 7 8 6 9 10 11 12 13 14 15 16 1 1 1 1 1 1 1 1 3 3 3 3 3 3 3 3 3.3K OHM LOGIC SUPPLY BARRIER STRIP POWER BARRIER STRIP
5 AMP LINE FUSUES (8)
(8) LED STATUS INDICATORS (8)
1 AMP LOGIC
50 CONDUCTOR
SHOCK, EXPLOSION, OR ARC FLASH. /g120 Disconnect all power before installing or working with this equipment. /g120 Verify all connections and replace all covers before turning on power. Failure to follow these instructions will result in death or serious injury. RIESGO DE DESCARGA ELECTRICA O EXPLOSION. /g120 Desconectar todos los suministros de energia a este equipo antes de trabajar con este equipo. /g120 Verificar todas las conexiones y colocar todas las tapas antes de energizer el equipo. El incumplimiento de estas instrucciones puede provocar la muerte o lesiones serias. RISQUE DE DESCHARGE ELECTRIQUE OU EXPLOSION /g120 Eteindre toutes les sources d'énergie de cet appareil avant de travailler dessus de cet appareil /g120 Vérifier tous connections, et remettre tous couverts en olace avant de mettre sous De non-suivi de ces instructions provoquera la mort ou des lésions sérieuses sérieuses. GEFAHR EINES ELEKTRISCHE N SCHLAGES ODER EINER EXPLOSION. /g120Stellen Sie jeglichen Strom ab, der dieses Gerät versorgt, bevor Sie an dem Gerät Arbeiten durchführen /g120Vor dem Drehen auf Energie alle Anschlüsse überprüfen und alle Abdeckungen ersetzen. Unterlassung dieser Anweisungen können zum Tode oder zu schweren Verletzungen führen. RISCHIO DI SCOSSA ELETTRICA O DELL’ESPLOSI ONE. /g120Spenga tutta l'alimentazion e che fornisce questa apparecchiatu ra prima del lavorare a questa apparecchiatu ra /g120Verificare tutti i collegamenti e sostituire tutte le coperture prima della rotazione sull'alimentazi one L'omissione di seguire queste istruz ioni provocherà la morte o di lesioni serie RISCO DE DESCARGA ELÉTTRICA OU EXPLOSÃO /g120Desconectar o equipamento de toda á energia antes de instalar ou trabalhar com este equipamen to /g120Verificar todas as conexões e recolocar todas as tampas antes de religar o equipamento O não cumprimento destas instruções pode levar á morte ou lesões sérias. DANGER / PELIGRO / DANGER /GEFAHR / PERICOLO / PERIGO
ANNEX - ENVIROMENTAL INFORMATION