PB16HQ CRYDOM | Alldatasheet

Document overview

  • Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
  • PDF pages: 3

Technical content

Input and output modules accepted interchangeably Operate with 5, 15 or 24 volt logic supplies Plug-compatible logic connections Screw terminal barrier block for load connections 5 amp field-replaceable fuses (LITTLEFUSE #251005 or equivalent) All even-numbered logic connections are logic ground PB16HQ MECHANICAL SPECIFICATIONS MOUNTING BOARD Rev. 070808 NOTES: 3) OPTIONAL JUMPERS AVAILABLE TO INTERCONNECT BARRIER STRIP COMMONS. ORDER 2 EACH JUMPER "JQ4". 1) CONNECTOR IS BERG 65863-145 OR EQUIVALENT. 4) LITTLE FUSE 251001 OR EQUIVALENT. 5) LITTLE FUSE 251005 OR EQUIVALENT. 2) 6-32 SCREW TERMINAL BARRIER STRIPS ACCEPT WIRE SIZES FROM 24 TO 12 AWG. c c c c c c JUMPERS CONNECTING LOGIC SUPPLY THROUGH HEADER CONNECTOR POSITIVE (+) LOGIC SUPPLY BUS TERMINATION DIMENSIONS: INCHES (MILLIMETERS) TOLERANCE: ± 0.20 ( ± 0,50) REPLACEABLE 1A LOGIC SUPPLY FUSE (SEE NOTE 4) LOGIC SUPPLY BARRIER STRIP NEGATIVE (-) LOGIC SUPPLY BUS TERMINATION SIGNAL INPUT/OUTPUT

50 CONDUCTOR MALE PIN

CONNETOR (SEE NOTE 1) POWER BARRIER STRIPS (SEE NOTE 2,3) REPLACEABLE POWER LINE FUSE (8) (SEE NOTE 5) GORDOS QUAD PACK DIGITAL DIFITAL I/O MODULES SOLD SEPERATELY SPARE 5A LINE FUSE (SEE NOTE 5) SWAGED STANDOFF THRU HOLE 0.15 (3,8) DIA F1 F2 F3 F4 F5 F6 F7 F8 PWR ON TB2R1 PIN 49 5V JUMPERS PIN F1A 0.375 (9,5) +5V GND 6.75 (171,5) 6.0 (152,4) 12 - 158 - 114 - 7 CROUZET 57 - 463 PB - 16HO 0 - 3 SPARE 5A FUSE 5.0 (127,0) 4 .5 (114,3) cc PWR ON 2-50EVEN PINS +5V GND

1 C 3 5 C 7 9 C 11 13 C 15

2 C 4 6 C 8 10 C 12 14 C 16

50 CONDUCTOR

(-) I/O MODULE PIN SOCKETS 5A LINE FUSES (8) LOWER BARRIER STRIP UPPER BARRIER STRIP SIGNAL INPUT/OUTPUT Captive-screw retaining system for Quad-Pack modules

SHOCK, EXPLOSION, OR ARC FLASH.

  • Disconnect all power before installing or working with this equipment.
  • Verify all connections and replace all covers before turning on power. Failure to follow these instructions will result in death or serious injury. RIESGO DE DESCARGA ELECTRICA O EXPLOSION.
  • Desconectar todos los suministros de energia a este equipo antes de trabajar con este equipo.
  • Verificar todas las conexiones y colocar todas las tapas antes de energizer el equipo. El incumplimiento de estas instrucciones puede provocar la muerte o lesiones serias. RISQUE DE DESCHARGE ELECTRIQUE OU EXPLOSION
  • Eteindre toutes les sources d'énergie de cet appareil avant de travailler dessus de cet appareil
  • Vérifier tous connections, et remettre tous couverts en olace avant de mettre sous De non-suivi de ces instructions provoquera la mort ou des lésions sérieuses sérieuses. GEFAHR EINES ELEKTRISCHE N SCHLAGES ODER EINER EXPLOSION.
  • Stellen Sie jeglichen Strom ab, der dieses Gerät versorgt, bevor Sie an dem Gerät Arbeiten durchführen
  • Vor dem Drehen auf Energie alle Anschlüsse überprüfen und alle Abdeckungen ersetzen. Unterlassung dieser Anweisungen können zum Tode oder zu schweren Verletzungen führen. RISCHIO DI SCOSSA ELETTRICA O DELL’ESPLOSI ONE.
  • Spenga tutta l'alimentazion e che fornisce questa apparecchiatu ra prima del lavorare a questa apparecchiatu ra
  • Verificare tutti i collegamenti e sostituire tutte le coperture prima della rotazione sull'alimentazi one L'omissione di seguire queste istruz ioni provocherà la morte o di lesioni serie RISCO DE DESCARGA ELÉTTRICA OU EXPLOSÃO
  • Desconectar o equipamento de toda á energia antes de instalar ou trabalhar com este equipamen to
  • Verificar todas as conexões e recolocar todas as tampas antes de religar o equipamento O não cumprimento destas instruções pode levar á morte ou lesões sérias. DANGER / PELIGRO / DANGER /GEFAHR / PERICOLO / PERIGO

ANNEX - ENVIROMENTAL INFORMATION