PA0105015

PA0004015 NORGREN | Alldatasheet

Document overview

• Manufacturer or author: Provided By alldatasheet.com(free datasheet download site)
• PDF pages: 20

Technical content

05/99 N/AL 9.12.001.01Our policy is one of continuous research and development. We therefore reserve the right to amend, without notice, the specifications given in this document.

Ordering Information

To order, quote appropriate product number from the tables on the following pages. When ordering Polyester reinforced PVC hose state the length of hose required. lAvailable in a variety of different types to suit a wide range of applications lAll tubing can be used with specific ranges of tube fittings lNylon and polyurethane tube available in several colours for ease of identification Technical Data Medium: Compressed air (Consult our Technical Service for use with other fluids) Operating Pressure: Refer to specific tubing type on the following pages Operating Temperature: Refer to specific tubing type on the following pages Tube Sizes Nylon: 4, 5, 6, 8, 10, 12, 14, 16, 22, 28 mm O/D Polyurethane: 4, 5, 6, 8, 10, 12 O/D Extraflexible Nylon: 8, 10, 12, 15 mm O/D Polyester reinforced PVC hose: 3, 5, 6.3, 8, 10, 12.5, 19, 25 mm I/D Polyester reinforced PVC hose assemblies: 4, 5, 6, 8, 10, 12, 16, 22, 28 O/D Metal Braided: 4, 5, 6, 8, 10, 12, 28 mm Copper – half hard and annealed: 4, 5, 6, 8, 10, 12, 16, 22, 28 mm O/D Double Wall Brazed Steel: 4, 6, 8, 10, 12 mm O/D Materials Nylon tube: nylon (polyamide) type 11 or 12 fully plasticised Polyurethane Polyester reinforced PVC: high quality electrically non- conductive plasticised PVC hose, high tensile polyester fibre braiding, galvanised steel ‘O’ clips and brass tailpieces on assembled hoses Metal braided hose: E90 nitrile rubber hose, galvanised steel braiding wire, brass ferrules, copper tailpieces Copper tube: phosphorous de-oxidised non arsenical copper to BS6017 grade Cu-DHP Double wall brazed steel: copper coated steel strip with plated external surface Tubing & Hose Metric Nylon, Polyurethane, Polyester Reinforced PVC, Metal Braided Rubber, Copper, Double Wall Brazed Steel

O/D I/D Product number Corporate Corporate tube tube Red Yellow Green Red Grey (mm) (mm) 15 m coil 25 m coil 100 m coil 15 m coil 25 m coil 100 m coil 15 m coil 25 m coil 100 m coil 25m coil 25m coil 4 2,5 PA0104015* PA0104025* PA0104100 PA0304015* PA0304025* PA0304100 PA0204015* PA0204025* PA0204100 PA0804025 PA0604025 5 3,0 PA0105015* PA0105025* PA0105100 PA0305015* PA0305025* PA0305100 PA0205015* PA0205025* PA0205100 - - 6 4,0 PA0106015* PA0106025* PA0106100 PA0306015* PA0306025* PA0306100 PA0206015* PA0206025* PA0206100 PA0806025 PA0606025 8 6,0 PA0108015* PA0108025* PA0108100 PA0308015* PA0308025* PA0308100 PA0208015* PA0208025* PA0208100 PA0808025 PA0608025 10 7,5 PA0110015* PA0110025* PA0110100 PA0310015* PA0310025* PA0310100 PA0210015* PA0210025* PA0210100 - - 12 9,0 PA0112015* PA0112025* PA0112100 PA0312015* PA0312025* PA0312100 PA0212015* PA0212025* PA0212100 - - 14† 11,0 – PA0114025 PA0114100 – PA0314025 PA0314100 – PA0214025 PA0214100 - - N/AL 9.12.001.02 05/99 Metric Tubing and Hose Our policy is one of continuous research and development. We therefore reserve the right to amend, without notice, the specifications given in this document. General Information – Metric Nylon Tubing To DIN Standards 73378 and 74324 Coils are supplied in polythene bags. Those coils marked * can also be supplied in boxes at nominal extra cost, add ‘C’ to end of product number. †Do not conform to above standards. 22 mm and 28 mm O/D tubing conforms to BS 5409 Part 1, Table 2. Other colours can be supplied for orders of sufficient quantity. This standard range of nylon tubing can be supplied in longer lengths to order, provided that a minimum economic production quantity is ordered. All of these coils are supplied in boxes or on drums. This standard range of polyurethane tubing can be supplied in longer lengths to order, provided that a minimum economic production quantity is ordered. O/D I/D Product number tube tube Natural Black Blue Brown (mm) (mm) 15 m coil 25 m coil 100 m coil 15 m coil 25 m coil 100 m coil 15 m coil 25 m coil 100 m coil 100 m coil 4 2,5 PA0004015* PA0004025* PA0004100 PA0704015* PA0704025* PA0704100 PA0504015* PA0504025* PA0504100 PA0404100 5 3,0 PA0005015* PA0005025* PA0005100 PA0705015* PA0705025* PA0705100 PA0505015* PA0505025* PA0505100 PA0405100 6 4,0 PA0006015* PA0006025* PA0006100 PA0706015* PA0706025* PA0706100 PA0506015* PA0506025* PA0506100 PA0406100 8 6,0 PA0008015* PA0008025* PA0008100 PA0708015* PA0708025* PA0708100 PA0508015* PA0508025* PA0508100 - 10 7,5 PA0010015* PA0010025* PA0010100 PA0710015* PA0710025* PA0710100 PA0510015* PA0510025* PA0510100 - 12 9,0 PA0012015* PA0012025* PA0012100 PA0712015* PA0712025* PA0712100 PA0512015* PA0512025* PA0512100 - 14† 11,0 PA0014015 PA0014025 PA0014100 – PA0714025 PA0714100 – PA0514025 PA0514100 - 16 12,0 PA0016015 PA0016025 – – – – – – – - 22† 17,0 PA0022015 PA0022025 – – – – – – – - 28† 22 PA0028015 PA0028025 – – – – – – – - O/D I/D Maximum working pressure (bar) Minimum bend radius (mm) tube (mm) tube (mm) at –40°C to +20°C 4 2,5 28 25 5 3,031 25 6 4,025 30 8 6 19 50 107,5 24 60 12 9,018 75 14 11,015 80 16 12,018 95 22 17,015 125 28 22,015 160 Working temperature °C Factor +30°C 0,83 +40°C 0,75 +50°C 0,64 +60°C 0,57 +80°C 0,47 Polyurethane Tubing O/D I/D Product number tube tube Natural Black Blue Red Yellow Green (mm) (mm) 25 m coil 100 m coil 25 m coil 100 m coil 25 m coil 100 m coil 25 m coil 100 m coil 25 m coil 100 m coil 4 2,5 PU0004025C PU0004100C PU0704025C PU0704100C PU0504025C PU0504100C PU0104025C PU0104100C PU0304025C PU0304100C 5 3,0 PU0005025C PU0005100C PU0705025C PU0705100C PU0505025C PU0505100C PU0105025C PU0105100C PU0305025C PU0305100C 6 4,0 PU0006025C PU0006100C PU0706025C PU0706100C PU0506025C PU0506100C PU0106025C PU0106100C PU0306025C PU0306100C PU0206100C 8 5,5 PU0008025C PU0008100D PU0708025C PU0708100D PU0508025C PU0508100D PU0108025C PU0108100D PU0308025C PU0308100D PU0208100D 10 7,0 PU0010025C PU0010100D PU0710025C PU0710100D PU0510025C PU0510100D PU0110025C PU0110100D PU0310025C PU0310100D PU0210100D 12 8,0 PU0012025C PU0012100D PU0712025C PU0712100D PU0512025C PU0512100D PU0112025C PU0112100D PU0312025C PU0312100D PU0212100D To calculate working pressures at various temperatures, multiply working pressure at –40°C to +20°C by factor given in table. Maximum continuous working temperature +80°C. Maximum working pressures Working pressure/temperature conversion factors O/D I/D Maximum Bend Natural tube tube working radius 25m coil (mm) (mm) Pressure (bar) (mm) at 20°C 8 6 10 30 PS0008025 10 8 8 40 PS0010025 12 10 6 60 PS0012025 15 12.5 6 110 PS0015025 Extraflexible Nylon Tubing Working temperature °C Factor +30°C 0,83 +40°C 0,75 +50°C 0,64 +60°C 0,57 To calculate working pressures at various temperatures, multiply working pressure at –40°C to +20°C by factor given in table. Maximum continuous working temperature +60°C. Working pressure/temperature conversion factors

05/99 N/AL 9.12.001.03 MMeettrriicc TTuubbiinngg aanndd HHoossee Our policy is one of continuous research and development. We therefore reserve the right to amend, without notice, the specifications given in this document. O/D I/D Maximum working pressure (bar) Minimum bend radius (mm) tube (mm) tube (mm) at –40°C to +20°C 4 2,5 106 5 3,011 7 6 4,09 9 8 5,5 9 16 107,09 17 12 8,09 25 To calculate working pressures at various temperatures, multiply working pressure at –40°C to +20°C by factor given in table. Maximum continuous working temperature +60°C. Maximum working pressures Working pressure/temperature conversion factors Working temperature °C Factor +30°C 0,85 +40°C 0,70 +50°C 0,60 +60°C 0,50 Product Hose Min. Hose Max (bar) ‘O’ clip Number bore bend Ø working product radius O/D pressure number PV2008030 3 51,0 8 31 48 0168 02 PV2010030 5 63,0 10 20 48 0168 03 PV2012030 6,3 76,0 11,5 17 48 0168 04 PV2014030 8 102 13,5 16 48 0168 05 PV2016030 10 114 16 16 48 0168 06 PV2019030 12,5 140 18,5 14 48 0168 07 PV2027030 20 203 27 9 48 0168 11 PV2033030 25 229 33 6 48 0168 15 Product A O/D B Max (bar) Min C D Number* tailpiece working bend hose hose pressure radius I/D O/D 42 0200 00 000 4 19,0 10 28 3 8 42 0210 00 000 5 21,5 10 28 3 8 42 0220 00 000 6 23,0 10 31,5 6,3 12 42 0230 00 000 8 26,0 10 31,5 6,3 12 42 0240 00 000 10 28,0 10 48,5 10 16 42 0250 00 000 12 30,0 10 48,5 10 16 42 0260 00 000 16 34,8 9 50,5 12,5 19 42 0270 00 000 22 42,0 7 70 19 27 42 0280 00 000 28 51,0 6 225 25 33 Polyester reinforced PVC hose 30m coils Pincers DC‘O’ ClipA To Order B Flexible hose assemblies A special pair of pincers, product number 39 0014 00, is available for crimping ‘O’ clips to hose. Instructions 1. Cut off the desired length of hose 2. Insert reusable tailpieces 3. Slip on the ‘O’ clips 4. Clamp tightly with pincers Polyester reinforced PVC hose Operating temperature: –20°C to +70°C. For use at temperatures above +70°C consult our Technical Service. *State the length of hose required when ordering. Maximum length 30m.

N/AL 9.12.001.04 05/99 Metric Tubing and Hose Our policy is one of continuous research and development. We therefore reserve the right to amend, without notice, the specifications given in this document. Product A B C E Min Max (bar) Number O/D A/F bend working tube radius pressure 42 0020 00 000 4 19 * 13 34 69 42 0020 00 250 4 19 250 13 34 69 42 0020 00 300 4 19 300 13 34 69 42 0020 00 350 4 19 350 13 34 69 42 0020 00 400 4 19 400 13 34 69 42 0020 00 500 4 19 500 13 34 69 42 0020 00 600 4 19 600 13 34 69 42 0020 00 750 4 19 750 13 34 69 42 0020 01 000 4 19 100013 34 69 42 0030 00 000 5 21 * 13 34 69 42 0030 00 250 5 21 250 13 34 69 42 0030 00 300 5 21 300 13 34 69 42 0030 00 350 5 21 350 13 34 69 42 0030 00 400 5 21 400 13 34 69 42 0030 00 500 5 21 500 13 34 69 42 0030 00 600 5 21 600 13 34 69 42 0030 00 750 5 21 750 13 34 69 42 0030 01 000 5 21 100013 34 69 42 0040 00 000 6 23 * 14 35 69 42 0040 00 250 6 23 250 14 35 69 42 0040 00 300 6 23 300 14 35 69 42 0040 00 350 6 23 350 14 35 69 42 0040 00 400 6 23 400 14 35 69 42 0040 00 500 6 23 500 14 35 69 42 0040 00 600 6 23 600 14 35 69 42 0040 00 750 6 23 750 14 35 69 42 0040 01 000 6 23 100014 35 69 B BC E A Flexible hose assemblies Metal Braided Rubber Hose Product A B C E Min Max (bar) Number O/D A/F bend working tube radius pressure 42 0050 00 000 8 26 * 17 39 69 42 0050 00 250 8 26 250 17 39 69 42 0050 00 300 8 26 300 17 39 69 42 0050 00 350 8 26 350 17 39 69 42 0050 00 400 8 26 400 17 39 69 42 0050 00 500 8 26 500 17 39 69 42 0050 00 600 8 26 600 17 39 69 42 0050 00 750 8 26 750 17 39 69 42 0050 01 000 8 26 100017 39 69 42 0060 00 000 10 28 * 19 39 69 42 0060 00 250 10 28 250 19 39 69 42 0060 00 300 10 28 300 19 39 69 42 0060 00 350 10 28 350 19 39 69 42 0060 00 400 10 28 400 19 39 69 42 0060 00 500 10 28 500 19 39 69 42 0060 00 600 10 28 600 19 39 69 42 0060 00 750 10 28 750 19 39 69 42 0060 01 000 10 28 100019 39 69 42 0070 00 000 12 30 * 22 51 47 42 0070 00 250 12 30 250 22 51 47 42 0070 00 300 12 30 300 22 51 47 42 0070 00 350 12 30 350 22 51 47 42 0070 00 400 12 30 400 22 51 47 42 0070 00 500 12 30 500 22 51 47 42 0070 00 600 12 30 600 22 51 47 42 0070 00 750 12 30 750 22 51 47 42 0070 01 000 12 30 100022 51 47 Metal braided rubber hoses are suitable for use with petrol, diesel fuel, paraffin and other liquids to pressures stated in the tables below. They are also suitable for use with compressed air up to a maximum working pressure of 10 bar. The maximum working pressures quoted in these tables have been taken under ideal conditions with non-pulsating pressures when used with compression tube fittings, see Section 99..66. Working temperature range -20°C to +100°C *State length of hose required if ordering non-standard lengths. Minimum length 155mm. When installing a flexible hose the following simple rules should be noted. 1. Flexible hose is weakened when installed in a twisted position. 2. Ample bend radius should be allowed to avoid collapsing the hose. 3. When hose is installed in a flexing application remember that metal end fittings are not part of the flexible portion. 4. Use elbows or adaptors to eliminate excess hose bends. Double wall brazed steel tubing is constructed from copper coated steel strip which is rolled twice around laterally, then furnace brazed to produce a tube of double wall structure, with a clear, scale free coppered bore, a plated external surface and a consistently uniform wall thickness. Double Wall Brazed Steel Tube Product O/D Inside Min Max Number tube diameter bend working 3m straight size radius pressure (bar) (10ft) (min) at 20°C* BU6304003 4 2,6 10 380 BU6306003 6 4,6 13 300 BU6308003 8 6,6 19 250 BU6310003 10 8,6 22 195 BU6312003 12 10,6 44 160 Tolerance on outside diameters is –0,07 mm to +0,05 mm. *Maximum working pressures stated are for tubes of straight length, with non-pulsating pressures when used with Enots compression tube fittings.

05/99 N/AL 9.12.001.05 MMeettrriicc TTuubbiinngg aanndd HHoossee Our policy is one of continuous research and development. We therefore reserve the right to amend, without notice, the specifications given in this document. Product O/D I/D Wall Min Recommended Number tube tube thickness bend safe working 10m coils size size radius pressure (bar) -200°C to +50°C CS6004010 4 2,8 0,6 12 128 CS6005010 5 3,4 0,8 15 138 CS6006010 6 4,4 0,8 19 112 CS6008010 8 6,4 0,8 24 81 CS6010010 10 8,4 0,8 30 64 33mm ssttrraaiigghhtt CS6012003 12 9,6 1,2 40 81 CS6016003 16 13,6 1,2 48 59 CS6022003 22 19,0 1,5 67 53 CS6028003 28 25,0 1,5 86 41 The following technical information is valid for copper tube when used with compression fittings, see Section 9.5. For further information please consult our Technical Service. Copper Tubing Standard Duty: Annealed Manufactured to BS 2871: Part 2 with dimensions generally to Table 4. Tolerances on O/D are +0,00mm to –0,08mm. The recommended safe working pressures are calculated in accordance with BS1306 with a stress value of 41N/mm 2 and minimum tube wall thickness. For safe working pressures at temperatures other than -200°c to +50°C refer to Pressure De-rating Factor table below. Copper Tubing Pressure De-rating Factor For temperatures other than -200°C to +50°C to to to to to Annealed 1,0 0,97 0,82 0,63 0,43 Half-hard 1,0 0,95 0,88 0,54 0,29 To calculate the working pressure at temperatures other than –200°C to +50°C multiply the working pressure given in the appropriate table by the factor given in this table.e.g. Safe working pressure of standard duty half-hard copper tube, 8 mm O/D at +120°C = 157 x 0,88 = 138 bar. Product O/D I/D Wall Min Recommended Number tube tube thickness bend safe working 3m straight size size radius pressure (bar) -200°C to +50°C CS7004003 4 2,8 0,6 12 193 CS7005003 5 3,4 0,8 15 208 CS7006003 6 4,0 1,0 19 218 CS7008003 8 6,0 1,0 24 157 CS7010003 10 7,6 1,2 30 150 CS7012003 12 9,6 1,2 40 122 CS7016003 16 13,6 1,2 48 89 CS7022003 22 19,0 1,5 67 81 CS7028003 28 25,0 1,5 86 62 Standard Duty: Half Hard Manufactured to BS 2871: Part 2 with dimensions generally to Table 4. Tolerances on O/D are +0,00mm to –0,08mm. The recommended safe working pressures are calculated in accordance with BS1306 with a stress value of 62N/mm 2 and minimum tube wall thickness. For safe working pressures at temperatures other than -200°c to +50°C refer to Pressure De-rating Factor table below. Product Description Number M/3314 Tube cutter

39012061 Replacement blades

Tube Cutter - Plastic Tubing Suitable for providing clean square cuts through 3mm to 19mm plastic tubing. Cutter is provided with Norgren branding in corporate red colour. 79mm 27mm Warning These products are intended for use in industrial compressed air systems only. Do not use these products where pressures and temperatures can exceed those listed under ‘Technical Data’. Before using these products with fluids other than those specified, for non-industrial applications, life-support systems, or other applications not within published specifications, consult Norgren. Through misuse, age, or malfunction, components used in fluid power systems can fail in various modes. The system designer is warned to consider the failure modes of all component parts used in fluid power systems and to provide adequate safeguards to prevent personal injury or damage to equipment in the event of such failure. System designers must provide a warning to end users in the system instructional manual if protection against a failure mode cannot be adequately provided. System designers and end users are cautioned to review specific warnings found in instruction sheets packed and shipped with these products where applicable.

06/97 N/AL 9.12.005.01Our policy is one of continuous research and development. We therefore reserve the right to amend, without notice, the specifications given in this document. WeldTube and Tube Strippers l Available in a variety of colours in four tube sizes l Outer cover protects against damage from weld spatter l Designed to be used with WeldFit push-in fittings l Good flexibility with tight bend radius capability l Good chemical resistance l Flame retardant outer cover Technical Data Operating Medium: Compressed Air, Water (Consult our Technical Service for use with other fluids) Operating Pressure: Vacuum 10 bar Working Temperature: -30 °C to 70°C Tube Sizes: Inner tube 6, 8, 10, 12 mm O/D Materials: Inner tube:- Polyurethane, 95° shore A. Outer tube:- Flame retardent PVC To order, quote the appropriate product number from the tables on the following pages. Metric

39004100 Stripper

39004160 Spare blades (2)

N/AL 9.12.005.02 06/97 W eldTube Our policy is one of continuous research and development. We therefore reserve the right to amend, without notice, the specifications given in this document. W arning These products are intended for use in industrial compressed air systems only. Do not use these products where pressuresand temperaturescan exceed those listed under ‘Technical Data’. Before using these products with fluids other than those specified, for non-industrial applications, life-support systems, or other applications not within published specifications, consult Norgren. Through misuse, age, or malfunction, components used in fluid power systems can fail in various modes. The system designer is warned to consider the failure modes of all component parts used in fluid power systems and to provide adequate safeguards to prevent personal injury or damage to equipment in the event of such failure. System designers must provide a warning to end users in the system instructional manual if protection against a failure mode cannot be adequately provided. System designers and end users are cautioned to review specific warnings found in instruction sheets packed and shipped with these products where applicable. General Information 138 This tube stripper ensures correct stripping of WeldTube The colours are for the outer PVC cover Tubing is supplied shrink-wrapped in 25m coils Other colours can be supplied for orders of sufficient quantity Tubing can also be supplied in longer lengths subject to economic order quantities Tube Stripper O/D O/D I/D Working Burst Bend Product number Outer tube Inner tube Inner tube pressure pressure radius Black Red Green Blue mm mm mm bar bar mm 8 6 4 10 30 40 WT4706025 WT4106025 WT4206025 WT4506025 10 8 6 10 30 50 WT4708025 WT4108025 WT4208025 WT4508025 12,5 10 7 10 30 65 WT4710025 WT4110025 WT4210025 WT4510025 14,5 12 9 10 30 75 WT4712025 WT4112025 WT4212025 WT4512025 To give full protection from weld spatter, the outer cover needs to be removed exposing the correct length of inner tube for insertion into the WeldFit fitting. The outer cover then fits into the collet counterbore, thus protecting system from spatter. Instructions for Use 1. Ensure tube is cut at 90°to the tube axis. This cut to be in the middle mark along tube. 2. Adjust cutting depth of stripper - adjust the cutting depth of the blade at the head screw and adjust to the outer cover thickness. 3. Lift the clip against the spring pressure and insert tube, lining up blade with the next mark from tube end (this ensures correct length is removed.) Release the clip. 4. To strip outer cover, turn the tool radially around the tube to make a circular cut. 5. Turn the blade (90°) up to the stop with the lever. Move tool along the tube to make longitudinal cut. 6. The outer cover can be levered off with the aid of the ground edge of the clip and removed.

l High mechanical strength l Large thermal range l Broad chemical resistance l Good fatigue resistance l Light weight l Low permeability l Heat and light stabilized l Excellent abrasion resistance Polyamide (Nylon) Tubing to DIN standards 73378 and 74324 * These products conform to DIN 74324, SAE J1394 and ISO 7628-1 = This product conforms to SAE J1394 not to DIN 74324 or 73378

• These products conform to DIN 74324 Other colours and sizes of metric nylon tubing can be supplied for orders of sufficient quantity. Standard range of nylon tubing can be supplied in long length coils to order, providing that a minimum economic production quantity is ordered. The automotive tubing range is suitable for commercial vehicle primary air braking and auxiliary air systems and can be used in conjunction with Norgren vehicle push-in fittings (FleetFit). OD x wall thickness Black• Red Green Yellow Blue (mm) 25m 100m 25m 25m 25m 25m 4 x 1.0 TP0704025 TP0704100 TP0104025 TP0204025 TP0304025 TP0504025 6 x 1.0* TP0706025 TP0706100 TP0106025 TP0206025 TP0306025 TP0506025 8 x 1.0* TP0708025 TP0708100 TP0108025 TP0208025 TP0308025 TP0508025 9 x 1.5 TP0709025 TP0709100 T00109024 TP0209025 TP0309025 TP0509025 10 x 1.25 TP0710025 TP0710100 TP0110025 TP0210025 TP0310025 TP0510025 10 x 1.5= TN0710025 TN0710100 TN0110025 TN0210025 TN0310025 TN0510025 11 x 1.5 TP0711025 TP0711100 TP0111025 TP0211025 TP0311025 TP0511025 12 x 1.5* TP0712025 TP0712100 TP0112025 TP0212025 TP0312025 TP0512025 15 x 1.5 TP0715025 TP0715100 TP0115025 TP0215025 TP0315025 TP0515025 16 x 1.5* TP0716025 TP0716100 TP0116025 TP0216025 TP0316025 TP0516025

These products are intended for use in industrial compressed air systems only. Do not use these products where pressuresand temperaturescan exceed those listed under ‘Technical Data’. Before using these products with fluids other than those specified, for non-industrial applications, life-support systems, or other applications not within published specifications, consult Norgren. Through misuse, age, or malfunction, components used in fluid power systems can fail in various modes. The system designer is warned to consider the failure modes of all component parts used in fluid power systems and to provide adequate safeguards to prevent personal injury or damage to equipment in the event of such failure. System designers must provide a warning to end users in the system instructional manual if protection against a failure mode cannot be adequately provided. System designers and end users are cautioned to review specific warnings found in instruction sheets packed and shipped with these products where applicable.

06/97 Our policy is one of continuous research and development. We therefore reserve the right to amend, without notice, the specifications given in this document. N/AL 9.12.004.01 Spring Coils PU Pneuflex Series l PU Pneuflex coils are suitable for high mechanical deformations, machine tools, etc. l Coils are supplied complete with swivel fittings at both ends l High degree of flexibility l Good resistance to abrasion and impact strength l Very short diameter on windings Technical Data Medium: Compressed air, water, inert gases, oils, hydrocarbons, solvents and any other fluid compatible with polyurethane Operating Pressure: See details overleaf Operating Temperature: -20°c to +50°c See details overleaf Tube Sizes 6, 8, 10, 12mm O/D 2, 4, 6, 8m maximum working lengths Thread Sizes: 1⁄8, 1⁄4, 3⁄8 BSPT Materials: Tubing Coils:Polyurethane polyester based Body and nut: brass nickel plated Protection spring: steel, zinc plated Seal: NBR To order, quote appropriate product numbers from the tables on the following page. Polyurethane

N/AL 9.12.003.02 06/97Our policy is one of continuous research and development. We therefore reserve the right to amend, without notice, the specifications given in this document. Product Diameter A B Effective C D Max working E number of tube Length Length Working Coil Length in Diameter pressure Thread D x d End A End B Length (m) neutral position (mm) on Windings bar PU310600218 6 x 4 300 100 2 165 32 10 R 1⁄8 PU310600418 6 x 4 300 100 4 350 32 10 R 1⁄8 PU310600618 6 x 4 300 100 6 545 32 10 R 1⁄8 PU310600818 6 x 4 300 100 8 720 32 10 R 1⁄8 PU310800228 8 x 5 500 100 2 180 42 10 R 1⁄4 PU310800428 8 x 5 500 100 4 400 42 10 R 1⁄4 PU310800628 8 x 5 500 100 6 630 42 10 R 1⁄4 PU310800828 8 x 5 500 100 8 800 42 10 R 1⁄4 PU311000228 10 x 6,5 500 100 2 185 52 9 R 1⁄4 PU311000428 10 x 6,5 500 100 4 400 52 9 R 1⁄4 PU311000628 10 x 6,5 500 100 6 635 52 9 R 1⁄4 PU311000828 10 x 6,5 500 100 8 800 52 9 R 1⁄4 PU311200238 12 x 8 500 100 2 180 65 9 R 3⁄8 PU311200438 12 x 8 500 100 4 390 65 9 R 3⁄8 PU311200638 12 x 8 500 100 6 590 65 9 R 3⁄8 PU311200838 12 x 8 500 100 8 780 65 9 R 3⁄8 General Information - PU Pneuflex Spring Coils Mounting Method Male thread and swivel fittings at both ends. PU Pneuflex Coils are coloured red. To calculate working pressures at various temperatures, multiply working pressure by factor given in table. Working Pressure/Temperature Conversion Factor Dimensional Drawing Warning These products are intended for use in industrial compressed air systems only. Do not use these products where pressuresand temperaturescan exceed those listed under ‘Technical Data’. Before using these products with fluids other than those specified, for non-industrial applications, life-support systems, or other applications not within published specifications, consult Norgren. Through misuse, age, or malfunction, components used in fluid power systems can fail in various modes. The system designer is warned to consider the failure modes of all component parts used in fluid power systems and to provide adequate safeguards to prevent personal injury or damage to equipment in the event of such failure. System designers must provide a warning to end users in the system instructional manual if protection against a failure mode cannot be adequately provided. System designers and end users are cautioned to review specific warnings found in instruction sheets packed and shipped with these products where applicable. Working temperature °C Factor 30c 0,85 40°c 0,70 50°c 0,60 CAB D E

10/96 N/UK 9.12.003.01Our policy is one of continuous research and development. We therefore reserve the right to amend, without notice, the specifications given in this document. Spring Coils PA Pneuflex Series l PA Pneuflex spring coils ideally suited for use with pneumatic tools, machine tools, industrial robots and many general applications l Spring coils supplied complete with swivel fittings at both ends l Good resistance to oils, hydrocarbons and solvents Technical Data Medium: Compressed air, water, inert gases, oils and any other fluid compatible with PA11, nickel plated brass and NBR Tube Sizes: 6, 8, 10, 12, 15 mm O/D 3, 3.75, 5, 7.5 and 15m maximum working lengths Operating Pressure: See details overleaf Operating Temperature: See details overleaf Materials Spring Coils: Nylon PA11, nickel plated brass fitting body, nitrile rubber seals, galvanised steel protection spring PA Pneuflex Threads BSPT thread 1⁄4, 3⁄8 BSPP thread 1⁄2 To order quote the appropriate product numbers from the tables on the following page. Nylon

N/UK 9.12.003.02 10/96Our policy is one of continuous research and development. We therefore reserve the right to amend, without notice, the specifications given in this document. General Information – PA Pneuflex Spring Coils Product number O/D tube I/D tube A B Length of closed Length of maximum Operating pressure Adaptor (mm) (mm) (mm) (mm) spiral (mm) C extension (m) D at +20° C (bar) (thread) E PA330600328 6 4 64 52 200 3 31 1⁄4 PA330600428 6 4 64 52 250 3,75 31 1⁄4 PA330600528 6 4 64 52 333 5 31 1⁄4 PA330600828 6 4 64 52 500 7,50 31 1⁄4 PA330601528 6 4 64 52 1000 15 31 1⁄4 PA330800328 8 6 86 70 200 3 22 1⁄4 PA330800428 8 6 86 70 250 3,75 22 1⁄4 PA330800528 8 6 86 70 333 5 22 1⁄4 PA330800828 8 6 86 70 500 7,50 22 1⁄4 PA330801528 8 6 86 70 1000 15 22 1⁄4 PA331000328 10 8 105 85 210 3 17 1⁄4 PA331000428 10 8 105 85 262 3,75 17 1⁄4 PA331000528 10 8 105 85 350 5 17 1⁄4 PA331000828 10 8 105 85 525 7,50 17 1⁄4 PA331001528 10 8 105 85 1000 15 17 1⁄4 PA331200338 12 10 134 110 200 3 12 3⁄8 PA331200438 12 10 134 110 250 3,75 12 3⁄8 PA331200538 12 10 134 110 333 5 12 3⁄8 PA331200838 12 10 134 110 500 7,50 12 3⁄8 PA331201538 12 10 134 110 1000 15 12 3⁄8 PA331500348 15 12 190 160 166 3 17 1⁄2 PA331500448 15 12 190 160 207 3,75 17 1⁄2 PA331500548 15 12 190 160 277 5 17 1⁄2 PA331500848 15 12 190 160 415 7,50 17 1⁄2 Mounting Method: Male thread and swivel fitting at both ends. Pneuflex Spring Coils are coloured yellow. Coils of 4 and 5 mm tube are available special order. W arning These products are intended for use in industrial compressed air systems only. Do not use these products where pressuresand temperaturescan exceed those listed under ‘Technical Data’. Before using these products with fluids other than those specified, for non-industrial applications, life-support systems, or other applications not within published specifications, consult Norgren. Through misuse, age, or malfunction, components used in fluid power systems can fail in various modes. The system designer is warned to consider the failure modes of all component parts used in fluid power systems and to provide adequate safeguards to prevent personal injury or damage to equipment in the event of such failure. System designers must provide a warning to end users in the system instructional manual if protection against a failure mode cannot be adequately provided. System designers and end users are cautioned to review specific warnings found in instruction sheets packed and shipped with these products where applicable. A B C D E Working temperature ° C Factor –40° C to +20° C 1,00 +30° C 0,83 +40° C 0,72 +50° C 0,64 +60° C 0,57 +80° C 0,47 To calculate working pressures at various temperatures, multiply working pressure at –40°C to +20°C by factor given in table. Maximum continuous working temperature +80°C. W orking pressure/temperature conversion factors

11/97 N/AL 9.12.002.01Our policy is one of continuous research and development. We therefore reserve the right to amend, without notice, the specifications given in this document. To order, quote appropriate product number from the tables on the following pages. When ordering Polyester reinforced PVC hose state the length of hose required. lAvailable in a variety of different types to suit a wide range of applications lAll tubing can be used with specific ranges of tube fittings lNylon tube available in several colours for ease of identification Technical Data Medium: Compressed air (Consult our Technical Service for use with other fluids) Operating Pressure: Refer to specific tubing type on the following pages Operating Temperature: Refer to specific tubing type on the following pages Tube Sizes Nylon: Nylon (food grade): 3⁄16", 1⁄4", 5⁄16", 3⁄8"O/D Nylon (spring coils): 3⁄16", 1⁄4", 5⁄16", 3⁄8", 1⁄2" Polyester reinforced PVC hose assemblies: 3⁄16", 1⁄4", 5⁄16", 3⁄8", 1⁄2", 3⁄4" O/D Copper – half hard and annealed: 1⁄8", 3⁄16", 1⁄4", 5⁄16", Double Wall Brazed Steel: 3⁄16", 1⁄4", 5⁄16", 3⁄8", 1⁄2"O/D Materials Nylon tube: nylon (polyamide) type 11 or 12 fully plasticised Nylon tube: (spring coils) type 11 or 12 fully plasticised Nylon tube (food grade): nylon (polyamide) type 11 or 12 unplasticised Polyester reinforced PVC hose: high quality electrically non- conductive plasticised PVC hose, high tensile polyester fibre braiding, galvanised steel ‘O’ clips and brass tailpieces on assembled hoses Metal braided hose: E90 nitrile rubber hose, galvanised steel braiding wire, brass ferrules, copper tailpieces Copper tube: phosphorous de-oxidised non arsenical copper to BS6017 grade Cu-DHP Double wall brazed steel: copper coated steel strip with plated external surface Tubing & Hose Inch Nylon, Food Grade Nylon, Polyester Reinforced PVC, Metal Braided Rubber, Copper, Double Wall Brazed Steel

N/AL 9.12.002.02 11/97 Inch Tubing and Hose Our policy is one of continuous research and development. We therefore reserve the right to amend, without notice, the specifications given in this document. General Information – Inch Nylon Tubing Nylon (spring coils) O/D I/D Maximum working Bending tube tube pressure at -40° radius size size to +20°C (bar) centreline Maximum working pressures Working temperature °C Factor -40°C to +20° 1,00 +30° 0,83 +40° 0,75 +50° 0,64 +60° 0,57 +80° 0,47 Working Pressure/Temperature Conversion Factors O/D I/D Product number tube tube Natural Red Black size size 50 ’coils 250’ coils 500’ coils 2000’ coils 50’ coils 250’ coils 50’ coils 250’ coils 1⁄8" 0,065" PA0051050C PA0051250 –– –– PA0751050C – 5⁄32" 0,100" PA0052050C PA0052250 –– PA0152050C – PA0752050C – 3⁄16" 0,125" PA0053050C PA0053250 – PA0053B00D PA0153050C – PA0753050C PA0753250 1⁄4" 0,175" PA0054050C PA0054250 PA0054500 PA0054B00D PA0154050C PA0154250 PA0754050C PA0754250 5⁄16" 0,215" PA0055050C PA0055250 PA0055500 – PA0155050C PA0155250 PA0755050C PA0755250 3⁄8" 0,260" PA0056050C PA0056250 PA0056500 – PA0156050C – PA0756050C – 1⁄2" 0.370" PA0057050C PA0057250 PA0057500 – PA0157050C – PA0157050C – To calculate working pressures at various temperatures, multiply working pressure at -40° to +20°C by factor given in table. Maximum continuous working temperature 80°C. Product O/D Colour number tube size PF1053100 3⁄16 Natural PF1054100 1⁄4 Natural PF1055100 5⁄16 Natural PF1056100 3⁄8 Natural Food Grade Tubing A special grade of nylon tubing is available for all food industry applications. This tubing is entirely odourless and tasteless, and will not impart extraneous flavour or odour to susceptible foods or beverages. Supplied in 100ft coils. O/D I/D Product number tube tube Blue Brown Green Yellow size 50’ coils 250’ coils 50’ coils 250’ coils 50’ coils 250’ coils 50’ coils 250’ coils 1⁄8" 0,065" PA0551050C –– – PA0251050C – PA0351050C – 5⁄32" 0,100" PA0552050C – PA0452050C – PA0252050C – PA0352050C – 3⁄16" 0,125" PA0553050C – PA0453050C – PA0253050C – PA0353050C – 1⁄4" 0,175" PA0554050C PA0554250 PA0454050C PA0454250 PA0254050C PA0254250 PA0354050C PA0354250 5⁄16" 0,215" PA0555050C PA0555250 PA0455050C PA0455250 PA0255050C – PA0355050C 3⁄8" 0,260" PA0556050C – PA0456050C – PA0256050C – PA0356050C –– 1⁄2" 0.370" PA0557050C – PA0457050C – PA0257050C – PA0257050C – 2" min straight 2" min straight B C A Product A B C Number nominal nominal nominal tube O/Dia coil I/Dia closed length 40007203 3⁄16"2 " 8 " 40007204 1⁄4"2 " 1 0 1⁄2"

11/97 N/AL 9.12.002.03 Inch Tubing and Hose Our policy is one of continuous research and development. We therefore reserve the right to amend, without notice, the specifications given in this document. ‘O ’ ClipA To Order B Flexible hose assemblies Polyester reinforced Product A O/D B Max Min Number* tail- working bend piece pressure radius 41 0307 00 000 3⁄16" 1" 10 0,98" 41 0308 00 000 1⁄4"1 1⁄8" 10 1,24" 41 0309 00 000 5⁄16"1 1⁄4" 10 1,49" 41 0310 00 000 3⁄8"1 3⁄8" 10 1,91" 41 0311 00 000 1⁄2"1 1⁄2" 9 1,99" 41 0313 00 000 3⁄4"1 3⁄4" 7 2,76" Operating temperature: –20°C to +70°C. For use at temperatures above +20°C consult our Technical Service. *State the length of hose required when ordering. Maximum length 100 ft. B BC E A Product A B C E Min Max Number O/D bend working tube radius pressure 41 0633 00 000 3⁄16 1" * 0,45" 1 3⁄4"6 9 41 0633 00 100 3⁄16 1" 10" 0,45" 1 3⁄4"6 9 41 0633 00 120 3⁄16 1" 12" 0,45" 1 3⁄4"6 9 41 0633 00 140 3⁄16 1" 14" 0,45" 1 3⁄4"6 9 41 0633 00 160 3⁄16 1" 16" 0,45" 1 3⁄4"6 9 41 0633 00 180 3⁄16 1" 18" 0,45" 1 3⁄4"6 9 41 0633 00 200 3⁄16 1" 20" 0,45" 1 3⁄4"6 9 41 0633 00 240 3⁄16 1" 24" 0,45" 1 3⁄4"6 9 41 0633 00 300 3⁄16 1" 30" 0,45" 1 3⁄4"6 9 41 0633 00 360 3⁄16 1" 36" 0,45" 1 3⁄4"6 9 41 0634 00 000 1⁄4 11⁄8" * 0,53" 2" 69 41 0634 00 100 1⁄4 11⁄8" 10" 0,53" 2" 69 41 0634 00 120 1⁄4 11⁄8" 12" 0,53" 2" 69 41 0634 00 140 1⁄4 11⁄8" 14" 0,53" 2" 69 41 0634 00 160 1⁄4 11⁄8" 16" 0,53" 2" 69 41 0634 00 180 1⁄4 11⁄8" 18" 0,53" 2" 69 41 0634 00 200 1⁄4 11⁄8" 20" 0,53" 2" 69 41 0634 00 240 1⁄4 11⁄8" 24" 0,53" 2" 69 41 0634 00 300 1⁄4 11⁄8" 30" 0,53" 2" 69 41 0634 00 360 1⁄4 11⁄8" 36" 0,53" 2" 69 41 0635 00 000 5⁄16 11⁄4" * 0,60" 2" 69 41 0635 00 100 5⁄16 11⁄4" 10" 0,60" 2" 69 41 0635 00 120 5⁄16 11⁄4" 12" 0,60" 2" 69 41 0635 00 140 5⁄16 11⁄4" 14" 0,60" 2" 69 41 0635 00 160 5⁄16 11⁄4" 16" 0,60" 2" 69 Metal Braided Rubber Hose - Inch Flexible hose assemblies Product A B C E Min Max Number O/D bend working tube radius pressure 41 0635 00 180 5⁄16 11⁄4" 18" 0,60" 2" 69 41 0635 00 200 5⁄16 11⁄4" 20" 0,60" 2" 69 41 0635 00 240 5⁄16 11⁄4" 24" 0,60" 2" 69 41 0635 00 300 5⁄16 11⁄4" 30" 0,60" 2" 69 41 0635 00 360 5⁄16 11⁄4" 36" 0,60" 2" 69 41 0636 00 000 3⁄8 13⁄8" * 0,71" 2 1⁄2"6 9 41 0636 00 100 3⁄8 13⁄8" 10" 0,71" 2 1⁄2"6 9 41 0636 00 120 3⁄8 13⁄8" 12" 0,71" 2 1⁄2"6 9 41 0636 00 140 3⁄8 13⁄8" 14" 0,71" 2 1⁄2"6 9 41 0636 00 160 3⁄8 13⁄8" 16" 0,71" 2 1⁄2"6 9 41 0636 00 180 3⁄8 13⁄8" 18" 0,71" 2 1⁄2"6 9 41 0636 00 200 3⁄8 13⁄8" 20" 0,71" 2 1⁄2"6 9 41 0636 00 240 3⁄8 13⁄8" 24" 0,71" 2 1⁄2"6 9 41 0636 00 300 3⁄8 13⁄8" 30" 0,71" 2 1⁄2"6 9 41 0636 00 360 3⁄8 13⁄8" 36" 0,71" 2 1⁄2"6 9 41 0638 00 000 1⁄2 11⁄2" * 0,92" 3" 47 41 0638 00 100 1⁄2 11⁄2" 10" 0,92" 3" 47 41 0638 00 120 1⁄2 11⁄2" 12" 0,92" 3" 47 41 0638 00 140 1⁄2 11⁄2" 14" 0,92" 3" 47 41 0638 00 160 1⁄2 11⁄2" 16" 0,92" 3" 47 41 0638 00 180 1⁄2 11⁄2" 18" 0,92" 3" 47 41 0638 00 200 1⁄2 11⁄2" 20" 0,92" 3" 47 41 0638 00 240 1⁄2 11⁄2" 24" 0,92" 3" 47 41 0638 00 300 1⁄2 11⁄2" 30" 0,92" 3" 47 41 0638 00 360 1⁄2 11⁄2" 36" 0,92" 3" 47 *State length of hose required if ordering non-standard lengths. Minimum length 6". When installing a flexible hose the following simple rules should be noted. 1. Flexible hose is weakened when installed in a twisted position. 2. Ample bend radius should be allowed to avoid collapsing the hose. 3. When hose is installed in a flexing application remember that metal end fittings are not part of the flexible portion. 4. Use elbows or adaptors to eliminate excess hose bends. Double wall brazed steel tubing is constructed from copper coated steel strip which is rolled twice around laterally, then furnace brazed to produce a tube of double wall structure, with a clear, scale free coppered bore, a plated external surface and a consistently uniform wall thickness. Double Wall Brazed Steel Tube Product O/D Inside Min Max Number tube diameter bend working 3m straight size radius pressure (bar) (10ft) at 20°C* BU6352010 5⁄32" 0,100" 3⁄8" 380 BU6353010 3⁄16" 0,131" 3⁄8" 340 BU6354010 1⁄4" 0,194" 1⁄2" 300 BU6355010 5⁄16" 0,256" 3⁄4" 250 BU6356010 3⁄8" 0,319" 7⁄8" 195 BU6357010 1⁄2" 0,444" 1 3⁄4" 160 Tolerance on outside diameters are –0,003" to +0,002".

N/AL 9.12.002.04 11/97 Inch Tubing and Hose Our policy is one of continuous research and development. We therefore reserve the right to amend, without notice, the specifications given in this document. The following technical information is valid for copper tube when used with compression fittings, see Section 9.5. For further information please consult our Technical Service. Copper Tubing Product O/D I/D Wall Min Recommended Number tube tube thickness bend safe working 10m coils size size (SWG) radius pressure (bar) (33ft) -200°C to +50°C CS6051033 1⁄8" 0,069 22 3⁄8" 205 CS6052033 5⁄32" 0,100 22 15⁄32" 156 CS6053033 3⁄16" 0,131 22 9⁄16" 126 CS6054033 1⁄4" 0,178 20 3⁄4" 120 CS6055033 5⁄16" 0,240 20 15⁄16"9 4 CS6056033 3⁄8" 0,303 20 1 1⁄8"7 7 3m straight (10ft) CS6057010 1⁄2" 0,404 18 1 1⁄2"7 7 CS6058010 5⁄8" 0,529 18 1 7⁄8"6 0 CS6059010 3⁄4" 0,622 16 2 1⁄4"6 8 CS6060010 7⁄8" 0,747 16 2 5⁄8"5 7 CS6062010 1 1⁄8" 0,997 16 3 3⁄8"4 4 Standard Duty: Annealed Manufactured to BS 2017: 1963 with dimensions generally to Table 1. Tolerances on O/D are +0,000" to –0,003". The recommended safe working pressures are calculated In accordance with BS1306 with a stress value of 41N/mm 2 (62 for half hard) and minimum tube wall thickness. For safe working pressures at temperatures other than -200°c to +50°C refer to Pressure De-rating Factor table below . Pressure De-rating Factor For temperatures other than -200°C to +50°C to to to to to Annealed 1,0 0,97 0,82 0,63 0,43 Half-hard 1,0 0,95 0,88 0,54 0,29 To calculate the working pressure at temperatures other than –200°C to +50°C multiply the working pressure given in the appropriate table by the factor given in this table.e.g. Safe working pressure of standard duty half-hard copper tube, 5⁄16 O/D at +120°C = 143 x 0,88 = 126 bar. Product O/D I/D Wall Min Recommended Number tube tube thickness bend safe working 3m straight size size (SWG) radius pressure (bar) (10ft) -200°C to +50°C CS7053010 3⁄16" 0,131 22 9⁄16" 192 CS7054010 1⁄4" 0,178 20 3⁄4" 184 CS7055010 5⁄16" 0,240 20 1 5⁄16" 143 CS7056010 3⁄8" 0,303 20 1 1⁄8" 117 CS7057010 1⁄2" 0,404 18 1 1⁄2" 117 CS7058010 5⁄8" 0,529 18 1 7⁄8"9 2 CS7059010 3⁄4" 0,622 16 2 1⁄4" 103 CS7060010 7⁄8" 0,747 16 2 5⁄8"8 7 CS7051010 1⁄8" 0,069 22 3⁄8" 313 CS7052010 5⁄32" 0,1 22 15⁄32" 238 Standard Duty: Half Hard Manufactured to BS 2017: 1963 with dimensions generally to Table 1. Tolerances on O/D are +0,000" to –0,003". Product O/D Inside Min Max Number tube diameter bend working 3m straight radius pressure (10ft) centreline CH6053010 3⁄16" 0,115" 9⁄16" CH6054010 1⁄4" 0,154" 3⁄4" CH6055010 5⁄16" 0,216" 1 5⁄16" See CH6056010 3⁄8" 0,279" 1 1⁄8" Note † CH6057010 1⁄2" 0,372" 1 1⁄2" CH6058010 5⁄8" 0,497" 1 7⁄8" CH6059010 3⁄4" 0,590" 2 1⁄4" CH6060010 7⁄8" 0,715 2 5⁄8" Heavy Duty † When used with compression tube fittings the maximum working pressure for heavy duty tubing should be regarded as being the same as for our standard duty for safety reasons. For other applications the heavy duty range will withstand higher pressures. For further and more precise details please consult our Technical Service. Warning These products are intended for use in industrial compressed air systems only. Do not use these products where pressuresand temperaturescan exceed those listed under ‘Technical Data’. Before using these products with fluids other than those specified, for non-industrial applications, life-support systems, or other applications not within published specifications, consult Norgren. Through misuse, age, or malfunction, components used in fluid power systems can fail in various modes. The system designer is warned to consider the failure modes of all component parts used in fluid power systems and to provide adequate safeguards to prevent personal injury or damage to equipment in the event of such failure. System designers must provide a warning to end users in the system instructional manual if protection against a failure mode cannot be adequately provided. System designers and end users are cautioned to review specific warnings found in instruction sheets packed and shipped with these products where applicable.

07/97 N/AL 9.13.001.01Our policy is one of continuous research and development. We therefore reserve the right to amend, without notice, the specifications given in this document. To order, quote appropriate product number from the tables on the following pages. lLow cost items for neat and secure fixing of tubing lMetallic clips are strong and resilient lNylon ties available in releasable or permanent locking types Technical Data Tubing Ties Operating Temperature: –50°C* to +85°C Minimum Tensile Strength: 13.61 kg - locking type 27.21 kg - releasable type Manufacturing Specification: to American Military Specification 23190 - Drawing No. 3367 Materials Tubing Ties and Mountings - Nylon Type 66, natural colour Tubing Clips - Zinc plated mild steel Tubing Ties – Releasable: 50, 81 mm maximum bundle diameter Lockable: 35, 50, 75 mm maximum bundle diameter Tubing Clips– Single sided: 4, 5, 6, 8, 10, 12, 16, 22, 28 mm O/D tube Double sided: 16, 22, 28 mm O/D tube 5⁄8, 3⁄4 O/D tube Tubing Channels– Acommodate 5, 6, 8 and 12mm O/D tube Accessories Tubing Ties & Tubing Clips

28.5 4.7 20.2 28.5 1.18 Mounting Base Product Number: 34 0380 24 Product Number: 34 0380 23 Tie can be inserted from any of 4 sides. Fixing adhesive backing. Both bases have additional fixing holes for use as required. D B C GØE A F Tubing Channels Product Length Width Maximum number Bundle ø 34 0380 11 200 4,7 50 34 0380 12 300 4,7 81 N/AL 9.13.001.02 11/97 Accessories Our policy is one of continuous research and development. We therefore reserve the right to amend, without notice, the specifications given in this document. Releasable ties Nylon Tube Ties Remain securely locked until intentionally released by operating finger catch. Product Length Width Maximum number Bundle ø 34 0380 01 150 3,5 35 34 0380 02 200 3,5 50 34 0380 03 300 3,5 75 Lockable ties Nylon Tube Ties Non-return cam action provides permanent fixing. Product A D D1 D2 D3 Q R number O/D tube 34 0218 02 4 20,3 12,7 5,3 4,2 5,1 6,4 34 0218 03 5 20,3 12,7 6,1 5,0 5,1 6,4 34 0218 04 6 21,8 12,7 7,6 6,6 5,1 6,4 34 0218 05 8 23,4 12,7 9,4 8,2 5,1 6,4 34 0218 06 10 24,4 12,7 10,5 9,7 5,1 6,4 34 0218 07 12 27,9 12,7 13,7 13,0 5,1 6,4 34 0215 08 16 34,3 19,1 16,0 15,8 7,1 7,1 36 0001 10 22 44,2 19,1 22,7 22,2 7,1 7,1 34 0215 11 28 51,6 19,1 28,6 28,6 7,1 7,1 D R D3 A Q/H11083 Tubing Clips - single sided Product A D D1 D2 D3 Q R number O/D tube Metric - single tube Inch - single tube 12.0 27.0 16.0 Mounting cradle For releasable ties For locking ties Nylon Tube Tie Mountings Product Number: 34 0380 21 Very neat fixing: body of cradle encapsulates head of tie. Fixing hole for M6 bolt. 12.5 20.6 3.5 Mounting Base Product Number: 34 0380 22 For use where space is restricted. Tie is slipped through slot in mounting. Fixing hole for M5 bolt. 13.2 19.0 3.8 19.0 1.3 Product No. of A B C D E F G number channels Ø 100HA0500 10 96,0 13,5 9,0 6,0 2,5 4,3 9,7 100HA0600 10 105,0 13,5 9,0 5,5 3,0 5,2 10,5 100HA0800 10 135,0 15,5 12,0 7,5 3,0 6,8 13,5 100H61200 6 118,0 17,5 16,5 10,0 3,4 10,5

11/97 N/AL 9.13.001.03 Accessories Our policy is one of continuous research and development. We therefore reserve the right to amend, without notice, the specifications given in this document. Warning These products are intended for use in industrial compressed air systems only. Do not use these products where pressuresand temperaturescan exceed those listed under ‘Technical Data’. Before using these products with fluids other than those specified, for non-industrial applications, life-support systems, or other applications not within published specifications, consult Norgren. Through misuse, age, or malfunction, components used in fluid power systems can fail in various modes. The system designer is warned to consider the failure modes of all component parts used in fluid power systems and to provide adequate safeguards to prevent personal injury or damage to equipment in the event of such failure. System designers must provide a warning to end users in the system instructional manual if protection against a failure mode cannot be adequately provided. System designers and end users are cautioned to review specific warnings found in instruction sheets packed and shipped with these products where applicable. Product A D D1 D2 D3 Q R number O/D tube 34 0219 02 4 25,6 12,7 5,3 8,2 5,1 6,4 34 0219 03 5 27,9 12,7 6,1 9,7 5,1 6,4 34 0219 04 6 32,0 12,7 7,6 13,0 5,1 6,4 34 0219 05 8 36,0 12,7 9,4 16,1 5,1 6,4 34 0219 06 10 39,9 12,7 10,5 19,3 5,1 6,4 34 0219 07 12 48,0 12,7 12,7 25,6 5,1 6,4 D R D3 A Q/H11083 Tubing Clips - single sided Product A D D1 D2 D3 Q R number O/D tube Metric - double tube Inch - double tube Product A D D1 D2 D3 Q R number O/D tube 34 0220 02 4 29,6 12,7 5,3 12,1 5,1 6,4 34 0220 03 5 32,0 12,7 6,1 14,5 5,1 6,4 34 0220 04 6 40,0 12,7 7,6 19,3 5,1 6,4 34 0220 05 8 47,9 12,7 9,4 24,0 5,1 6,4 34 0220 06 10 55,6 12,7 10,4 28,8 5,1 6,4 34 0220 07 12 60,6 12,7 13,7 38,4 5,1 6,4 D R D3 A Q/H11083 Tubing Clips - single sided Product A D D1 D2 D3 Q R number O/D tube Metric - triple tube Inch - triple tube Product A D D1 D2 D3 Q R number O/D tube 34 0216 08 16 57,2 19,1 16,0 7,1 19,1 36 0003 10 22 76,3 19,1 22,7 7,1 22,2 34 0216 11 28 89,0 19,1 28,6 7,1 28,6 D AD1 QØ R R Tubing Clips - double sided Product A D D1 D2 D3 Q R number O/D tube Metric Inch Product Pack Drilling required number 48 0034 24 200 Cast iron – 4,5mm dia. drill Solid metal – 4,4mm dia. drill Sheet metal – 4mm dia. drill Self-tapping screw 12.7 This screw is suitable for clips on tubes up to and including 1/2" O/D and 12mm O/D. For larger sizes use a 1/4" or 6 mm bolt.