P6SMB_1 TSC | Alldatasheet

Document overview

  • Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
  • PDF pages: 4

Technical content

Dimensions in inches and (millimeters) Version: A06 P6SMB SERIES

600 Watts Surface Mount

Transient Voltage Suppressor SMB/DO-214AA .083(2.10) .077(1.95) .012(.31) .006(.15) .012(.31) .006(.15) .008(.20) .004(.10) .056(1.41) .035(0.90) .147(3.73) .137(3.48) .187(4.75) .167(4.25) .103(2.61) .078(1.99) .209(5.30) .201(5.10) F e a t u r e s /cuspopen For surface mounted application in order to optimize board space /cuspopen Low profile package /cuspopen Built-in strain relief /cuspopen Glass passivated junction /cuspopen Excellent clamping capability /cuspopen Fast response time: Typically less than 1.0ps from 0 volt to BV min. /cuspopen Typical I R less than 1 μA above 10V /cuspopen High temperature soldering guaranteed: 260oC / 10 seconds at terminals /cuspopen Plastic material used carries Underwriters Laboratory Flammability Classification 94V-0 /cuspopen 600 watts peak pulse power capability with a 10 x 1000 us waveform by 0.01% duty cycle M e c h a n i c a l D a t a /cuspopen Case: Molded plastic /cuspopen Terminals: Pure tin plated lead free, /cuspopen Polarity: Indicated by cathode band /cuspopen Standard packaging: 12mm tape (EIA STD RS-481) /cuspopen Weight: 0.093gram Maximum Ratings and Electrical Characteristics Rating at 25 oC ambient temperature unless otherwise specified. Type Number Symbol Value Units Peak Power Dissipation at TA=25 o C, Tp=1ms( Note 1) PPK Minimum 600 Watts Steady State Power Dissipation Pd 3 Watts Peak Forward Surge Current, 8.3 ms Single Half Sine-wave Superimposed on Rated Load (JEDEC method) (Note 2, 3) - Unidirectional Only IFSM 100 Amps Maximum Instantaneous Forward Voltage at 50.0A for Unidirectional Only (Note 4) VF 3.5/5.0 Volts Typical Thermal Resistance (Note 5) RθJC RθJA oC/W Operating and Storage Temperature Range TJ, TSTG -65 to + 150 oC Notes: 1. Non-repetitive Current Pulse Per Fig. 3 and Derated above T A=25oC Per Fig. 2. 2. Mounted on 5.0mm (.013 mm Thick) Copper Pads to Each Terminal. 3. 8.3ms Single Half Sine-wave or Equivalent Square Wave, Duty Cycle=4 pulses Per Minute Maximum. Devices for Bipolar Applications 1. For Bidrectional Use C or CA Suffix for Types P6SMB6.8 through Types P6SMB220A. 2. Electrical Characteristics Apply in Both Directions.

RATINGS AND CHARACTERISTIC CURVES (P6SMB SERIES) FIG.5- TYPICAL JUNCTION CAPACITANCE (UNIDIRECTIONAL) V( ), BREAKDOWN VOLTAGE. VOLTSBR PAC NOITCNUJ,JC )Fp(.ECNATICA VR=0 Tj =25 C f = 1.0MHz Vsig = 50 mVp-p O MEASURED at STAND-OFF VOLTAGE, V WM 1 10 100 200 100 1000 6000 FIG.1- PEAK PULSE POWER RATING CURVE P , PEAK PULSE POWER, KW PPM tp, PULSE WIDTH, sec. 0.1 s 1.0 s 10 s 100 s 1.0ms 10ms 0.1 100 NON-REPETITIVE PULSE WAVEFORM SHOWN in FIG.3 T = 25 C J O FIG.2- PULSE DERATING CURVE PEAK PULSE POWER (P ) or CURRENT (I ) PP PPM TA, AMBIENT TEMPERATURE. ( C) O DERATING IN PERCENT AGE. % 0 25 50 75 100 125 150 175 200 100 FIG.4- MAXIMUM NON-REPETITIVE FORWARD SURGE CURRENT UNIDIRECTIONAL ONLY IFSM, PEAK FOR WARD SURGE CURRENT NUMBER OF CYCLES AT 60Hz AMPERES 8.3ms Single Half Sine Wave JEDEC Method 1 2 4 6 8 10 20 40 60 80 10010 100 200 FIG.3- PULSE WAVEFORMCLAMPING POWER PEAK PULSE CURRENT t, TIME, ms 0 1.0 2.0 3.0 4.0 100 150 PULSE WIDTH (td) is DEFINED as the POINT WHERE the PEAK CURRENT DECAYS to 50% of I PPM Half Value - IPPM 10/1000 sec. WAVEFORM as DEFINED by R.E.A. tr = 10 sec Peak Value I PPM td Version: A06

Dimensions in inches and (millimeters) ELECTRICAL CHARACTERISTICS (TA=25OC unless otherwise noted) Breakdown Voltage Test Stand-Off Maximum Maximum Maximum Maximum Device Device VBR Current Voltage Reverse Leakage Peak Pulse Clamping Temperature Marking (Volts) (Note 1) @IT VWM at VWM Current IRSM Voltage at IPPM Coefficient Code Min Max (mA) (Volts) I D (uA) (Note 2)(Amps) V C(Volts) of V BR(% / OC)

Test Stand-Off Maximum Maximum Maximum Maximum Device Device VBR Current Voltage Reverse Leakage Peak Pulse Clamping Temperature Marking (Volts) (Note 1) @IT VWM at VWM Current IRSM Voltage at IPPM Coefficient Code Min Max (mA) (Volts) I D (uA) (Note 2)(Amps) V C(Volts) of V BR(% / OC) Notes: 1. VBR measured after IT applied for 300us, IT=square wave pulse or equivalent. 2. Surge current waverform per Figure 3 and derate per Figure 2. 3. For bipolar types having VWM of 10 volts and under, the ID limit is doubled. 4. For bidirectional use C or CA suffix for types P6SMB6.8 through P6SMB220A. 5. All terms and symbols are consistent with ANSI/IEEE C62.35. ELECTRICAL CHARACTERISTICS (TA=25OC unless otherwise noted) Breakdown Volta